Search Documents

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr,5 Fieldner and Davis,6 and others, 7 has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M.8 standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting she results in those types of fuel which give erroneous results due to mechanical losses.

Jan 1, 1932

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1986 was $405.2 million, a slight decrease from that of 1985. Alabama was second in the Nation in production of bauxite, crushed marble, and ferroalloys; third b fire clay; fifth in masonry cement and lime; sixth in total clays; and seventh in recovered sulfur. Alabama ranked 19th nationally in value of nonfuel minerals produced. Cement, clays, lime, sand and gravel, and stone were the major commodities produced.

Jan 1, 1988

The Federal Coal Mine Health and Safety Act of 1969 limits to 2 milligrams per cubic meter (for dust containing a maximum of 5% quartz) the average respirable dust concentration to which individual miners may be exposed. Section 205 of the Act directs that an appropriate exposure formula for dusts with quartz content in excess of 5% be established. This formula, entered in F. R. Document 70-12351 filed September 16, 1970, is 10 milligrams per cubic meter divided by % quartz. Thus, the total respirable dust exposure permitted limits the quartz to a maximum of 100 micrograms. For example, if % quartz is 5%, 10 mg/5 = 2 milligrams, and (.05) (2 mg) = 100 micrograms. Similarly, if % quartz is 10%, 10/10 = 1, and (.10) (1 mg) = 100 micrograms, etc. If the % quartz is less than 5%, the 2 mg/M3 limit prevails.

Jan 1, 1974

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By James W. Myers

"Packaged fuel" is the trade name applied by the industry to a product consisting of coal screenings and a binder compressed into 3 -or 4-inch cubes and wrapped (six or eight in a package) in sturdy paper and sealed with gummed tape. Parry describes the product in greater detail and distinguishes clearly between packaged fuel and briquettes. The industry developed from the desire of retail coal dealers to improve utilization of the relatively large quantities of slack sizes that result from the degradation, during shipping and handling in the yard, of friable coal, particularly Pocahontas coal. During the war an attempt was made to apply this technique to anthracite fines, and a recent publication of the U. S. Bureau of Mines reported the results of physical and combustion tests on packaged fuels containing anthracite fines. References made in this report to the previous investigation on packaged fuels containing anthracite represent data or conclusions presented in Report of Investigations 3882. This investigation was conducted as a continuation of the previously reported studies and consisted of physical and combustion tests of packaged fuels made from high-volatile bituminous coal, as well as the low-volatile bituminous coal ordinarily used in the industry, to determine their relative suitability for domestic firing. Particular attention was given to the smoke-producing properties of the packaged fuels because of the increasing importance of the prevention or reduction of smoke from hand-fired domestic heating plants resulting from the widespread enactment of smoke-prevention ordinances.

Jan 1, 1951

By J. G. Donaldson

Optimum conditions are given for chloridizing pyrite, marcasite, chalcopyrite, arsenopyrite, stibnite, and covellite with chlorine gas. The formation of metal chlorides is affected by the time and temperature of chloridizing, and by particle size of the sample. Chloridizing data also are given for chemically precipitated antimony (III) sulfide and copper (II) sulfide.

Jan 1, 1962

By Henry P. Cole

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/technical workplaces are described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training is explored. Research and development activities that may improve mine health and safety training are suggested. Most of these research and development activities were completed later in the project. This additional work is reported in the project technical report #2 and the final report. The research reported in the present document was completed in 1984 -85. Many of the initial findings reported in this document are updated in the later project final report.

Jan 1, 1988

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1974 is compared with consumption in 1973 and 1975 (preliminary data).

Jan 1, 1977

By S. S. Cole, C. E. Wood, T. L. Joseph

"INTRODUCTION Iron ore containing titanium was first used in blast furnaces over a century ago. It is well known that TiO2 is a slag-forming material that will increase the amount of slag produced by the usual gangue materials, silica and alumina. Increase in the volume of slag due to the presence of TiO2 and a lack of information concerning its effect on the properties of the slag have prevented the general use of titaniferous ore. Also rather com¬mon belief among furnace operators that the bottom of the furnace builds up when ores containing TiO2 are smelted has militated against the use of titaniferous ore. This building up of the hearth has been attributed to the formation of copper-colored crystals of titanium cyanonitride, which have been observed in the salamanders of blast furnaces. Until recently the availability of nontitaniferous iron ore has left little incentive to use ore containing titanium.The presence of vanadium in certain deposits of titaniferous magnetite in New York State has created new interest in problems connected with the use of titanium-bearing ore. It appears that most of the vanadium in this ore can be recovered in pig iron, which can be blown in a converter to produce a slag containing vanadium in amounts suitable for the production of ferrovanadium.The Titanium Division of the National Lead Co. recently erected a largo mill to treat ore from Sanford Hill, in Essex County, New York, about 50 miles west of Port Henry. The ore deposit was acquired from the MacIntyre Iron Co. and is often referred to as Sanford ore. It is one of the largest deposits of Iron-bearing material to be found east of the Lake Superior region and is being mined by open-pit methods."

Jan 1, 1943

By Thomas E. Finch

This report is an engineering-economic evaluation of alternate methods of handling the parting between two coal seams. It consists of evaluations of parting stowing techniques applicable in a representative, thick seam western United States mine. Methods are examined for their potential implementation, and an estimated operating cost per yard of material moved is developed. The methods are of two categories castback or haulback. Haulback methods use truck haulage except With scrapers, and the castback methods are a direct stowage with no intermediate haulage equipment. Possible equipment combinations include draglines, shovels, hydraulic backhoes, bucket wheel excavators, scrapers, and front end loaders. The purpose of this report is to evaluate the effective competetiveness of the various alternatives.

Jan 1, 1975

By Victor R. Spironello

The Bureau of Mines has conducted studies of the slags related to ferrous technology to evaluate experimentally acceptable substitutes for the auxiliary flux, mineral fluorspar, in steelmaking operations. Comparative heats were made in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF) to evaluate a waste material known as "used potlining." Used pot lining is recovered from alumina reduction cells after its useful life and contains significant levels of fluorine and sodium in various compounds. This material in both lump and pelletized form provided adequately fluid slags, based on observations made during BOF operation. No adverse effects were found on furnace performance, metal and slag chemsitry, the strength of the steel produced, or the environment. Fluorine recovery in the slag was about the same as that obtained when using fluorspar, as were the losses to the scrubber water and solids. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag. The sodium recovered in the slag apparently also contributed to fluidity, since the fluorine input was at about two-thirds that of the fluorspar. Used potlining was determined experimentally to be a satisfactory substitute for fluorspar in basic oxygen steelmaking.

Jan 1, 1982

By A. U. Miller

"Ventilation is one of the meet important factors in mining, although until recent years less thought has probably been given to effective ventilation than to any other one phase of mining. In the past, very little, if any, attention was given air courses until they became so constricted by falls that the volume of air was greatly reduced; and, in addition, the stoppings and doors were so poorly constructed that only a very small percentage of air reached the face workings.As a matter of fact, mines have been visited where the volume of air being circulated in certain sections was much larger than in others, and where the management was striving to increase the flow of air in those sections with the least air current, believing the ventilation to be deficient. After sampling and analyzing the return air from the various sections in such mines it has been found that the quality of the air in certain places with the largest flow was more impure than in some of those with the least flow.In past years, practically all mine fans were operated by steam-driven engines supplied with steam from the mire boiler plant. No check was made on the steam consumption or the power cost of operating the fan, therefore the management had very little if any definite information as to cost of ventilating the mine.With the increased use of electrically-driven equipment in mines electricity is being used more and more to drive mine ventilating fans, and since in many instances the current is purchased from central power plants operators have come to realize that in many cases the cost of operating the fans is very high. Some engineers estimate that it ranges from 20 to 50 per cent of the total power cost of the mine. This information, together with the fact that mines are now being developed on a larger scale, requiring larger quantities of air for the men to dilute the gases liberated, has caused the large progressive companies to make, a more comprehensive study of mine ventilation, resulting in a decided improvement in the quality and quantity of air at the face workings, as well as reducing materially the ventilating costs."

Oct 1, 1930

By Wilton Johnson

The development and use of minerals and mineral fuels are essential to national security and to the maintenance of an expanding economy. As a Nation, we often met these needs but failed to recognize and assess the impact that mining and mineral processing activities have on other natural resources. Currently, the growing demand for energy and minerals is accompanied by an increasing awareness that the provision of these resources must not conflict with society's demand for a clean and habit-able environment. Although present mining and mineral processing activities incorporate, or have under development, technology capable of minimizing environ-mental impacts on land, air, and water, many older operations, particularly in the first half of this century, lacked the technological, social, and environmental insights that exist today. Consequently, a substantial backlog of damaging and potentially damaging conditions remains from such problems as mine subsidence, acid water generation, burning and nonburning waste banks, abandoned surface-mined lands, abandoned underground mine fires, and abandoned mine shafts and oil and gas wells.

Jan 1, 1979

By Ronald W. Stingelin

The geology of the roof of the Pittsburgh coal bed was studied and mapped in nine contiguous counties containing the bulk of the remaining reserves of this coal bed in the northern Appalachian Coal Basin. Drill core records from Belmont and Monroe counties, Ohio, Washington and Greene counties Pennsylvania, and Ohio, Marshall, Wetzel, Monongalia, and Marion counties, West Virginia provided the data for twelve computer generated regional geologic variable maps. Four of these geologic variables (overburden thickness, vertical distance to the rider coal, lithology at the five foot horizon above the roof of the mineable Pittsburgh seam, and the number of lithologic changes within the 30 foot interval above the roof of the mineable Pittsburgh seam) were used to estimate the risk of potential roof falls by a methological scheme developed during this study. A hazard zone risk map was developed showing a generalized regional trend of increasing risk from west to east across the basin. Mapping of individual geologic variables and mapping of hazard risk can be done at any scale. The accuracy of the mapping is primarily dependent on the density of the drill core records. Geologic feature maps and the hazard risk map contained in this report are reduced (1 :500,000 scale) versions of the larger scale (1 :62,500) maps prepared for the Bureau of Mines as map folios.

Jan 1, 1979

By Walter E. Pittman

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

Jan 1, 1982

By Franklin D. Cooper

This Bureau of Mines report reviews in detail the foundry coke situation in the United States in 1975. It discusses intrinsic production problems and identifies opportunities for modifying operating practices so that the quality and yield of foundry coke can be enhanced without unnecessary investment in new equipment. Major topics include operating data and attendant practices and problems, the relationship of carbonization phenomena to coke quality and yield, environ- mental impacts of foundry coke plant operations, suggested research and development opportunities, and data on components of oven charges and on foundry coke production and shipments.

Jan 1, 1977

By S. J. Davenport

The increased consumption and importation of fluorspar and cryolite (1)3/ in recent years, and especially the addition of fluorine compounds to drinking water in the United States, have aroused renewed interest in the properties of such compounds and possible health hazards incident to their use. It has been suggested that the issuance of a revision and elaboration of Information Circular 7311, The Hazards of Hydrogen Fluoride Poisoning in the Mineral and Allied Industries, which hay been out of print for some time, would be opportune. Fluorine minerals have been known since the Middle Ages. Fluorine was isolated in 1886 by Moisson (2).

Jan 1, 1954

By Sam S. Taylor

Disposal of brines produced with crude petroleum and natural gas is a continually increasing problem. The necessity for studying this problem has been realized more generally in recent years, and in August 1934 an agreement was made between the Kansas State Board of Health and the United States Bureau of Mines to conduct a cooperative technical study of methods of brine disposal. To date one paper in the technical press4/ and three reports5/6/ have been published in which are given results of studies carried on under this cooperative agreement. In the Mid-Continent fields, the methods used most generally for handling oil-field brines are: (1) Impounding in evaporation ponds; (2) controlled diversion into surface streams; and (3) injection into subsurface formations through wells assigned for this purpose. Various States recognize one or more of the methods as legally authorized procedure. Impounding brine in ponds and solar evaporation have proved inadequate as a general rule, owing, usually, to the porous nature of the soil, the low rate of evaporation, or both. Diversion, of

Jan 1, 1937