Search Documents

By Oliver Bowles

The use of fire as a source of heat was the first step from primitive existence toward modern civilization, and heat has performed functions of inestimable importance throughout the ensuing ages. The first commercial steam engine invented in 1698 demonstrated that heat was an important source of power, and heat has since become the motivating force for railroad trains and steamboats as well as for machines in multitudes of factories. Aside from its function of supplying power, heat is an agent of vast importance in chemical reactions and engineering processes. Because of the high temperature of steam under pressure, losses by radiation from boilers and pipes become excessive unless the radiating surfaces are covered with insulating materials. Insulation is important also for hot-water pipes and many other types of equipment from which heat may radiate. Radiation losses from heated surfaces increase rapidly

Jan 1, 1943

By Brian L. Quick

Problem: The National Institute for Occupational Safety and Health's [NIOSH] National Occupational Research Agenda (DHHS Publication No. 96 115) reports that approximately 50% of miners will experience hearing loss by age 50, compared to only 9% of the general population. The present investigation examines three antecedents believed to be associated with miner's use of hearing protection. Method: A posttest delayed posttest control group field research design was employed to assess antecedents toward wearing hearing protection. Results: Following the initial posttest, miners' attitudes and subjective norms were antecedents to intentions to wear hearing protection devices. Also, intentions toward wearing hearing protection predicted hearing protection behaviors. Approximately six weeks later, miners' attitudes and perceived behavioral control were each significant predictors of intentions to wear hearing protection and again, intentions were positively associated with hearing protection behaviors. Impact on Industry: Our results indicate that appeals to normative influences may be the most effective antecedent to employ when persuading coal miners to wear hearing protection. However, messages designed to impact attitudes and perceived behavioral control were also effective.

Jan 1, 2008

Reduce the cost of modifying uranium well casings so that leaching solutions can pass through, but sand grains are blocked. Approach The well casing and surrounding cement are perforated at the mineralized zone by impinging them with high pressure water jets. How It Works A nozzle assembly is attached to a high pressure (15,000 psi) pipe and lowered into the well casing which typically is schedule 40 PVC (poly-vinyl chloride). The high pressure pipe line is extended down Into the casing until it reaches the mineralized zone. The upper end of the pipeline is then connected by a high pressure hose to the outlet of a 10,000 psi pump. Turning the pump on for 5 seconds causes a high velocity water jet to cut through the well casing and the surrounding cement. Figure 1 shows a high pressure pipe being installed in a well casing. Cutting small diameter holes in the casing allows the leachant to enter the casing and be pumped to the surface. However, the holes are small enough to prevent most sand grains from entering. Numerous holes are usually cut through the casing. The 3-nozzle assembly shown in Figure 2 cuts three holes, one above another.

Jan 1, 1978

By Forrest T. Moyer

INJURY experience in the metal and nonmetal mineral industries during 1964 was better in rates of occurrence but worse in severity rates than in 1963. The frequency rate of injuries per million man-hours was improved at metal mills, nonmetal mines, and sand and gravel operations, and was virtually unchanged at metal mines; however" the rate of occurrence of work injuries at nonmetal mills, stone operations, nonferrous reduction and refining plants, and slag plants was higher than in 1963. The severity rate of injuries during 1964, data for which are presented for the first time in this chapter, was better at metal mills, nonmetal mines, stone operations, and slag plants. However, the severity rate was worse at metal mines, nonmetal mills, sand and gravel plants, and nonferrous smelters.

Jan 1, 1965

By Yumi Nakashima, Setsuo Maeda

Vibration magnitude and frequency of the z-axis vehicle seat are time-variant, which are influenced by not only vehicle vibration characteristics themselves but also road surfaces, speeds and the human body. There is little in the current reporting about evaluating and analyzing automobile seat vibration that focuses on the time-variant. Yaguchi et al.1 has proposed a method to evaluate automobile seat vibration that is based on judgments using a subjective mental state. Their method focuses on the time-variant magnitude of the peak frequency on a power spectrum density. However, their method has no consideration of all the frequency contents of the discomfort, nor comparison between different peak frequency vibrations. Suzuki2 has emphasized that the vehicle vibration should be judged by a series of vibration stimuli to evaluate, because the vehicle vibration is time-variant, which isn’t a matter of the relationship between a single vibration stimulus and a subjective response. He clarified that the human sensation to the vehicle vibration discomfort changes every moment showing the relationship between the frequency-weighted r.m.s. acceleration calculated every 5 seconds and the category judgment to vehicle vibration discomfort every 5 seconds. However, his study doesn’t show what parameter connects to the subjective final judgment to vehicle vibration. Therefore, we applied the method similar to ISO100563 considering the time-variant to the vehicle seat z-axis vibration evaluation. The new method for the vehicle seat vibration considering the time-variant was examined on the hypothesis that the final subjective evaluation must be conducted from the judgment summarizing a series of vibration stimuli. Methods The vibration bench system, which reproduces the movement of a vehicle floor, was used for the experiment with the single-axis (vertical direction) four-post road simulator system, which is usually used for a car, as shown in Fig.1. The experiment was done on the right side of the vibration bench using the floor vibration which was 5.5 minutes, 0.822 m/sec2 (Wk) over the range 0.5-20Hz with 4 male subjects (age ave21.5, SD0.5, weight ave75kg, SD7.91kg, height ave166.8cm, SD5.2cm) and 4 suspension seats. As Fig.2 shows, subjects evaluated the degree of discomfort every 5 seconds to each seat vibration measuring the seat z-axis vibration acceleration. [ ]

Jan 6, 2006

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By Mark S. Redfern, Kim M. Corneliusa, Christopher A. Hamrick, Sean Gallaghera

Coal miners often handle heavy electrical power cables, weighing up to 10 kg per meter. These cables are manually lifted and attached to the mine roof to prevent damage from mobile underground equipment. Data suggest that workers who commonly perform cable handling tasks experience a high rate of lost time back injuries. In this study, six male underground miners performed a total of 12 cable-hanging tasks in standing, stooping, and kneeling postures, during which kinematic and ground reaction force data were collected. Reductions in vertical work space were found to result in a linear increase in the peak moment experienced by the lumbarspine (p<0.05). In restricted postures, peak moments were not significantly different in stooping vs. kneeling postures (p>0.05). Average lumbopelvic flexion during the tasks was highest in stooping conditions, followed by standing and kneeling exertions (p<0.05). Implications of this data with respect to design of cable handling tasks are presented and discussed. Keywords: Biomechanics, posture, low back pain, restricted workspace, mining

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils rind 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Figure 1 shows this building, market; "Main high school building?, with respect to other buildings, pipe lines, oil wells, and gas lines on the property.

Jan 1, 1937

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils avid 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Fire 1 shows this building, marked "Main high school building", with respect to other buildings, pipe lines, oil wells, and gas lines or the property.

Jan 1, 1937

By Pakalnis Rimas, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

By Charlie Wyche

In 1980, gold, silver, and pit and quarry construction materials were the principal minerals produced in the Dominion of Fiji. The combined value of these minerals totaled some $7.2 million,2 over 85% of all mineral production, Production of cement, sand and gravel, and quarry products continued to increase, but gold and silver production from Fiji&apos;s only operating mine declined slightly from the previous year&apos;s level. Mineral exploration has been carried out by U.S., Australian, British, Canadian, West German, and South African companies since the early 1960&apos;s, and a high level of activity was maintained throughout 1980. At the end of 1980, some 40 mineral prospecting licenses covering over 4,300 square kilometers were in force, and 19 applications were under consideration by the Mineral Resources Department. Total expenditures by mining companies on land base projects exceeded $6 million in 1980.

Jan 1, 1982

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

By John R. Bartels

Remote operation of continuous mining machines has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory studied the workplace relationships between continuous miner operators and various tramming tasks of the equipment using motion capture data, operator response times, and field of view data to evaluate the factors influencing operator-machine struck-by events (contact with a solid object) in a virtual mine environment. It is not feasible (nor ethical) to use human subjects to directly evaluate factors that precipitate such injuries. However, use of motion analysis data and digital human models can facilitate analysis of struck-by accident risk by allowing investigators to manipulate factors that influence injury. Factors included in this study included machine speed, direction of escape, the direction the operator was facing relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck.

Jan 1, 2008

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

This chapter presents proportionate mortality ratios (PMRs) derived from death certificate data in the National Occupational Mortality Surveillance (NOMS) database for the years 1986 through 1993. At the time this report was prepared, 1993 was the latest year for which data were available. Industry is classified under the 1980 U.S. Bureau of the Census classification system [Bureau of the Census 1982]; cause of death, under the International Classification of Diseases, Ninth Revision (ICD-9) [World Health Organization 1977]. A PMR of 100 indicates a mortality risk for a particular industry group that is similar to that for all industry groups combined. A PMR over 100 suggests a higher risk; a PMR under 100 suggests a lower risk. PMRs are subject to many factors that affect their reliability and validity and may not be comparable across populations with very different causes of death. An elevated PMR for a specified cause of death among an occupational or industry group may indicate a relationship between a work exposure and the cause of death specified. However, there are many limitations of PMRs as a measure of risk; they are most useful for generating hypotheses about exposure-disease relationships, which can then be tested in other studies. Selected PMRs are presented separately for males and females for coal mining, metal mining, nonmetallic mineral mining and quarrying (which includes nonmetal, stone, and sand and gravel), and for oil and gas extraction. All PMRs have been adjusted for age and race. In general, PMRs are presented only if the lower 95% confidence limit exceeded 100. If a PMR in an ICD-9 subcategory was above 100, however, the PMR for the larger category into which the subcategory falls is always presented and may be less than 100. PMRs can be expected to be elevated for conditions that have a high prevalence in particular occupational groups. PMRs showed elevated values for conditions known to affect miners, such as coal workers&apos; pneumoconiosis, pneumoconiosis due to silica, tuberculosis, chronic pulmonary heart disease, and injuries. Additional findings of interest were- • An elevated PMR for myocardial infarction among male coal miners (table 2-1); • Elevated PMRs for neurologic disease in general and anterior horn cell disease, in particular among male metal miners (table 2-3); • An elevated PMR for rheumatic heart disease in male metal miners (table 2-3); • Elevated PMRs for malignant neoplasms of the digestive organs and peritoneum and for malignant neoplasms of the colon and rectum in female nonmetal miners (table 2-6); and • Elevated PMRs for non-A, non-B hepatitis and arteriosclerotic heart disease among male oil and gas workers (table 2-7).

Jan 5, 2000

By William J. Campbell

Expansion measurements of platinum, added as an internal standard, are used for thermal calibration of X-ray cameras and diffractometers. Accuracy of the temperatures derived by this technique depends on the precision of expansion measurements and the reliability of reference expansion data. Temperature measurements to ± 1° C. require ?d or ?a to be determined within ± 0.001 percent. Selected expansion data are concluded to be reliable to 2° C., 5° C., and 25° C., over the temperature ranges 0° C. to 700° C., 700° C. to 1,000° C., and 1,000° C. to 1,700° C., respectively. Tabular expansion values from 25° C. to 1,700° C. in 2° C. intervals were calculated from the following equation; Expansion, percent = [8.91 + 1.28 x 10-3(t-25) + 0.04 x 10-6(t-25) ] [t-25.104 ] These tabular values facilitate future corrections of published temperatures as more reliable expansion-temperature data become available.

Jan 1, 1962

By F. A. Rutledge, H. Marstraander, J. H. Hulbert, G. A. Apell

"INTRODUCTION The inability of Alaska coal mines to supply the quantity of coal required by public and private consumers and by the armed forces in Alaska caused the Coal Procurement Section of the Alaska Department, U. S. Army, to be established. It proposed to investigate the coal deposits and to expedite production of coal. The Bureau of Mines has closely cooperated in this program and was in direct charge of exploration. As to develop and equip an underground coal mine would have taken time and the need for coal was acute, a deposit that could be prepared for mining quickly was desirable. Several such deposits of stripping coal were known to occur in the Nenana field and were examined by the Bureau. One of these, the Diamond strip mine 4 miles west of Healy, was brought into production late in the fall of 1943. This mine was operated for the Army Coal Procurement Section by the C. F. Lytle Co. and the Green Construction Co.The Roth property, or Leasing Block No. 28, in the Healy Creek Valley offered the largest available tonnage of both stripping coal and total reserves. A program of exploration by the Bureau of Mines was inaugurated in 1943 and completed in 1944. Field parties of the Federal Geological Survey mapped the area had correlated the coal beds during the 1944 and 1945 summer seasons."

Nov 1, 1946

By Kara A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature, and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68 °C and 141 °C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large scale experimental configuration, the installation specifications of the fire suppression system, and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature, and limited water application on the suppression system performance.

Jan 1, 2010

By Ralph Husack

The Bureau of Mines investigated the effect of gamma radiation on reactions between Pennsylvania anthracite and fluorine and chlorine. In the tests with fluorine about 90 percent of the coal reacted at 350° C to form volatile products whether or not irradiation was employed. Up to 0.8 ml of liquid products per gram of anthracite was collected. Among the 25 com-pounds indicated by gas chromatography, fluoroform and l,l-difluoroethylene were tentatively identified from their relative retention times and perfluoro-cyclopentane from its infrared spectrum. In addition, a clear, hard, wax, probably a fluorocarbon, was formed at 45° C in both the presence and absence of radiation. With chlorine there was no significant difference due to radiation, and preliminary tests indicated that the chlorine reacted more with the organic matter of anthracite at 200° C than with inorganic matter. At 400° C the results were inconclusive because of excessive corrosion in the reaction vessel.

Jan 1, 1966

By Wilbur I. Duvall

In a review of so 40 papers on damage to residential structures resulting from blasting, only 3 were found that present data on the observed amplitude and frequency of the vibration levels produced by blasting together with an observed degree of damage to a residential structure. The data from these three reports have been analyzed statistically to determine if one of the quantities, displacement, velocity, or acceleration, is more reliable than the others for estimating the degree of damage to a residential structure. From this analysis the conclusion is drawn that a given degree of damage to a structure is most closely related to the magnitude of the particle velocity of the wave motion passing thru the earth at the structure location. On the average, only minor damage it observed for peak particle velocities of 5.4 inches per second, and major damage is observed for peak particle velocities of 7.6 inches per second. When the spread of the data is taken into consideration, the following statement can be made: Wave motions that have a peak particle velocity in excess of 2 inches per second have a fair probability of producing some damage to structures, whereas wave motions that have a peak velocity less than 2 inches per second have a very low probability of causing any damage. Therefore, the recommendation is made that vibration levels in the vicinity of residential structures should be maintained below a peat particle velocity of 2 inches per second. The above criterion for safe blasting is considered to hold over a wide variety of soil and rock conditions because the original data were obtained for a wide range of soil and rock conditions and on various types of residential structures. INTRODUCTION Ever since explosives were discovered and developed for mining purposes, there has existed the problem of what effects the air and ground vibrations resulting from blasting have on structures of various types. This problem is

Jan 1, 1962