Search Documents

By George S. Rice

The prevention of coal-mine explosions has been one of the chief purposes of the Bureau of Mines. In facti the first Federal appropriation relating to mining methods, in 1908, authorized the investigation of the causes of mine explosions and the possible methods of preventing them. When that investigation started the mining industry had not determined the real causes of a succession of terrible coal-mine explosions in various countries, culminating in the great disasters at CoulTièl'es, France, and Monongah, W. Va. Coal dust as an agent of widespread explosions had been under suspicion, and watering to allay the dust was recommended by some mining engineers but the watering of coal-mine dust was adopted in comparatively few mines of the United States and Great Britain, and had not been introduced widely in any country except Germany. Rock dusting, another method of preventing explosions of coal dust, was early tested with success by the Bureau of Mines in its fist gallery at Pittsburgh and, beginnig in 1911, at the experimental mine, Bruceton, Pa. Several of the fist publications i of the bureau suggested that rock dust be used in gaseous or dusty bituminous mines, and in 1915 Technical Paper 842 strongly recommended it. Since that time additional tests in the experimental mine have fully confied this :ft judgment.

Jan 1, 1924

By R. Lusignea

This report describes the development of a device for the nondestructive testing of resin grouted roof bolts by means of mechanical frequency response. Various alternative methods were evaluated and the mechanical frequency response method was selected. An interactive program of design, testing, and development culminating in the current prototype instrument demonstrated the capabilities of the method and suggested potential applications of the instrument. The resin bolt testing device utilizes a swept frequency dynamic compliance measurement in the 1 to 2 kHz range which is interpreted by an electronic signal processor to give a "GO" or "NO GO? readout. Field tests have shown that the device can reliably determine the bond quality of the front half of the bolt (nearest the roof surface). Tests were carried out on both experimentally installed bolts and typical mine bolts installed by a conventional bolting machine. The development program has led to recommendations for improvement of the prototype and future development work.

Jan 1, 1979

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concen¬tration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidaticn practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concentration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidation practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

Watershed Jll in Jefferson County, Ohio we instrumented in 1977 as one of three watersheds established for the purpose of investigating surface mining and reclamation effects upon local hydrology, sediment discharge, and sediment and water quality. Each watershed was less than 50-acres in size, and was in a different geologic setting within southeastern Ohio. Surface runoff and ground¬water levels were monitored. Samples were taken for sediment determination and chemical analysis prior to mining. Monitoring and sampling continued through the period of watershed disturbance caused by mining and reclamation activities, which began in May 1980 at Watershed Jll. A psuedo-postreclamation period followed the initial cessation of man-machine activity on the watershed. A second reclamation effort occurred in the fall of 1981 and was to be followed by a third in 1982 after observations ceased. A true final postreclamation period was not monitored at this site, because the erosion control practice (terrace diversions) failed after each reclamation. Watershed Jll was a small pasture and wooded watershed with sandstone and shale above the mined coal seam prior to mining. A clay layer under the coal supported a perched saturated zone, termed the top aquifer for convenience. A lower underclay supported a second saturated zone called the middle aquifer. A lower perched aquifer had been dewatered by previous deep mining. After about three years of premine data and about two and one-half years of mining reclamation and psuedo-postreclamation data, the following general observations may be made: 1. The mining-reclamation phase was very short, and the postmining period was characterized by erosion failures and remedial disturbances that kept the watershed condition and size in a state of change. It was impossible to collect sufficient data to confidently characterize the hydrologic-sediment-chemical aspects of the mining period or of a postreclamation period and, most importantly, of the future watershed after its various properties and characteristics have ceased adjusting to its severe disturbance and reconstitution. 2. A seeding of wheat followed by grasses and legumes was not a particularly successful reclamation practice in terms of stabilizing the new soil. Numerous rills and small gullies developed in spite of installed diversions. 3. Storm runoff rates and yields at the watershed outlet increased from the premine, (phase 1) to the mining-reclamation (Phase 2) periods, and remained at or near the Phase 2 level through the postreclamation (Phase 3a) period. 4. The top aquifer changed in physical and chemical character as a result of mining and was becoming reestablished as the project drew to a close; but it is impossible to predict its final configuration or character. 5. Dewatering of the top aquifer resulted in a complete cessation of baseflow because the middle aquifer water table lay below the elevation of the watershed outlet. 6. The top and middle aquifers were merged in one area of the watershed where the upper coal underclay was disturbed. 7. Failure of the diversion terraces and their outlet obscured the effects of the reclamation practice upon sediment concentration and yields. There was little difference in sediment concentrations between Phases 2 and 3a. 8. Drinking water standards were met by surface waters throughout the period of observation except for two samples that exceeded the nitrate-N allowable level of 10 mg/l. 9. In all Phase 3 surface-water samples, iron concentrations were within the limits established by OSM, and manganese concentrations exceeded the regulation level only once. pH fell below the lower regulation level of 6.0 between 10% and 20% of the time. 10. The chemical quality of sediments was generally about the same after reclamation as before mining, with the exception of organic carbon, which decreased.

Jan 1, 1983

By W. J. Wiehagen

The Work Crew Performance Model (WCPM) seeks to define performance variability within similar tasks of an underground work crew and relate observed variability to a cost consequence. Performance variability is described using work site observations to determine the adherence to job elements con¬tained within a standard operating procedure. Key components of the WCPM include (1) job definition through task analyses and the ranking of job elements by perceived cost consequence, (2) observational techniques for establishing performance baselines by measuring adherence to safe and proficient job procedures, and (3) cost linkages between adherence to task procedures and measures of consequence for noncompliance. Data presented within this report were obtained through the study of shuttle car operation in an underground mine in Appalachia. Observed adherence to safe and proficient job procedures by opera¬tors matched well with the consensus profiles (measured through a nominal group technique) with min¬ing personnel. It was also found that experienced operators consistently outperformed less experienced, incidental operators. These findings imply potential use of the WCPM as a practical procedure for thinking systematically about the choices available to reduce performance variability. Field application of the model can offer useful data to evaluate training and financially support performance improvement strategies that can be tested for their ability to reduce human error.

Jan 1, 1994

By Bruce F. Grant

This report discusses research being done by the Petroleum and Natural Gas Branch und the Applied Physics Branch of the Bureau of Mines to deter-mine the most effective uses of explosives in shooting oil and gas wells, as measured in terms of rates of production from the wells. An experimental investigation of the effects of detonating explosives in shallow holes drilled in rocks, chosen to be similar to those forming oil and gas reservoirs, forms the basis of this study. Records obtained from strain gages placed in the rock around the experimental shots permit determination of the generation and propagation characteristics of the strain wave. Water-injection tests made on the test holes before and after shooting allow the increase in fluid conductivity resulting from the shot to be determined. By rotating these data to the physical properties of the rock, and by conducting shooting experiments over the range of rock types common to oil and gas reservoirs, it is expected that relationships between the fluid conductivity and the properties of the explosive and rock can be developed and used for designing efficient shots for oil and gas wells. Four series of experiment.al tests were completed during the summer of 1949 and are described herein. The results of these tests confirmed the feasibility of the experimental approach and permitted outlining the plans for future research discussed in this report. This report is presented to acquaint industry with this research program and the progress to date, so that the Bureau may have the benefit of suggestions from interested readers.

Jan 1, 1950

By Sam Friedman

The Bureau of Mines conducted experiments using bench-scale apparatus to explore the effect of large changes in process variables on the yield and composition of the gases produced by passing 800° C steam through a fixed bed of Pittsburgh seam (hvab) coal. The total yield of combustible gases increased throughout the given range for the following variables: Superficial steam velocity increasing from 0.02 to 0.12 fps, pressure increasing from 1,000 to 6,000 psig, residence time increasing from 0 to 60 minutes, and temperature increasing from 800° to 900° C; however, a greater increase in the yield of hydrogen in comparison with the increase in yield of methane reduced the gross heating value of the gas to around 470 Btu per scf at conditions giving the maximum yield. Pressures of 1,000, 3,000, and 6,000 psig at 0.09 fps steam velocity, 800° C, and 60 minutes residence time, respectively, produced methane yields of 20, 24, and 22 percent, based on maf coal, with the gross heating value of the CO2-free gas decreasing from 552 to 520 and to 470 Btu per scf. Methane concentrations in the CO2-free gas were 26, 22, and 14 percent, respectively. Based on the gross heating value of the coal, the percentage of the heating value recovered in the gas was 60, 71, and 87 percent, respectively. The use of tungsten sulfide as a catalyst for converting carbon oxides and hydrogen into methane was explored briefly using both a sulfur-free gas rich in methane and a sulfur-bearing synthesis gas (3H2:1CO).

Jan 1, 1968

By Steven G. Grannes

This U.S. Bureau of Mines report summarizes Federal mandatory belt conveyor automatic fire suppression system installation requirements and inspection procedures, identifies system failure modes observed during in-mine investigations, and suggests system design and maintenance upgrades which, if implemented, would result in an improvement in overall system reliability. This report is a compilation of recommendations based on discussions with Mine Safety and Health Administration (MSHA) inspectors, review of manufacturer's literature, discussions with mine personnel, and research investigations of automatic fire suppression system performance in the laboratory and in mines. The Code of Federal Regulations (CFR) requirements for installation, inspection, and maintenance of fire suppression systems should be regarded as minimum standards.

Jan 1, 1990

By Peter G. Chamberlain

The surge in gold and silver prices during the 1970's attracted many new mining operators and has rekindled interest among experienced ones. With its low capital investment requirements and fast payout, leaching has attracted many operators--particularly those with small or low- grade deposits. Although in certain situations leaching offers many advantages over conventional mining methods, many operators are uncertain how these relatively new techniques should be implemented. Consequently the Bureau of Mines has prepared this circular to disseminate information on gold and silver leaching practices, techniques, and problem. Engineering data gathered from 26 operations indicate that most ores are leached in heaps following crushing and distribution on pads. Metal values are recovered from cyanide leach solutions using either zinc precipitation or charcoal adsorption. Potential problems that my hamper on block development of a leaching operation are poor percolation characteristics of the ore, calcium salt buildup, low temperatures, and solution losses. An extensive bibliography on gold and silver leaching is appended.

Jan 1, 1984

By Ellsworth Y. Dougherty, Edwards F. Fitzhugh

"INTRODUCTION During the summer of 1945 the Bureau of Mines made approximately 200 miles of reconnaissance magnetic surveys in north-central Mirnesota. The survey started near the western end of the Mesabi Iron Range and extended into the area to the southwest, west, and northwest and also southward to the-northern limits of the Cuyuna Iron Range. The purpose of the survey was to data to assist exploration for iron ore in the region through:1. Supplying a relatively unit form network of traverses, by which and future surveys of localities in the urea ray be correlated. Suggesting localities in which more detailed magnetic surveys may be justified, and, Disclosing localities in which there is lass hope of obtaining significant results from further magnetic surveys.The instrument used was a Hotchkiss Superdip, and traverses for calibration and comparison were run with a Schmidt-type magnetometer. Field observations and work directly related thereto were carried out under contract by E. J. Lang-year Co., Minneapolis. Engineers of the Bureau of Mines planned, directed, and reviewed the survey."

Aug 1, 1946

By H. M. Thorne

Oil shale, a potential source of products presently obtained from petroleum, is found in many countries. The most extensive known deposits from the standpoint of potential shale oil in place are those in Brazil and the United States of America. Mining methods used for oil shale range from open-pit operations for shallow deposits to room-and-pillar and longwall techniques for deposits with thick overburdens. Oil shales from different sources vary greatly in the amounts and types of organic and inorganic constituents. By retorting, the organic material is converted to oil, gas, and coke. The largest percentages of oil are obtained from materials having the highest hydrogen content. Over 2,000 retorting systems have been patented, but only a few have been used industrially, and no single process seems best for all types of shales or economic conditions. Shale oils have different characteristics, depending on the source rock and method of retorting. They contain large quantities of olefinic hydrocarbons and more oxygen, nitrogen, and sulfur derivatives of hydrocarbons than most petroleums. Consequently, petroleum refining methods usually must be modified for shale oil. This is particularly true in catalytic processing. Hydrogenation, even under mild conditions, improves shale-oil refinability. Several byproducts may be obtained from both the retorting and refining steps,

Jan 1, 1964

By August J. Kwitowski

This report presents the results of a joint Bureau of Mines-U.S. Department of Energy project that evaluated a newly developed low-coal mining system: the 4M miniminer system. The evaluation took place from April through October 1981 and determined potential health, safety, and productivity factors for the mining system using the surface test facilities at Bruceton, PA. The planning, testing, results of testing, and a summary evaluation of the 4M miniminer system are included in the report. The miniminer system was found to be a very good concept with future potential for safe, healthful, and economic production in thin-seam mining. The mining system was also judged to have considerable potential for use in some coal seams that are presently considered unminable by other existing mining equipment. The preproduction, prototype version of the miniminer system that was tested suffered from several safety and production problems. These problems are also described, along with suggested remedies.

Jan 1, 1989

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983

By Alan Mayton, N. Kumar Kittusamy, Christopher Jobes, Farid Amirouche

Industrial equipment exposes individuals to whole-body vibration (WBV) and mechanical shock. This exposure can negatively impact their health, safety, comfort, and working efficiency and performance. Accordingly, proper seat design is an important consideration in reducing the adverse effects of WBV exposure to vehicle operators. Since the human body is sensitive to low frequency WBV, ride quality is a basic and important element of good seat design. When designing a suitable seat, it is essential to understand vibration exposure environment of workers and how well they can tolerate this environment [1]. This is particularly true in the mining industry. Mayton et al. [2] reported on a low-coal shuttle car seat design that underwent limited, yet successful underground mine trials. Building on this work, a follow-up study compared NIOSH and existing seat designs on low- and mid-coal seam shuttle cars. The NIOSH seat designs included viscoelastic foam, which has properties similar to those found in a mechanical spring/damper suspension system. The seats also included an adjustable lumbar support and a fore-aft seat adjustment. The NIOSH seat designs contrast with the existing seat design, which have little or no lumbar support and include inexpensive foam padding of the type commonly used in furniture. This paper will focus on the seat designs for the mid-coal seam shuttle car and compare subjective comfort data collected from five vehicle operators with ISO 2631 – based reduced comfort boundary (RCB) analysis of recorded vibration levels. Methods Experimental data were collected using three different tools: triaxial accelerometers, pre-amplifiers, and filters connected to a data recorder; a visual analog scale (VAS); and a short questionnaire. Researchers recorded quantitative or objective vehicle vibration data to determine the input and output acceleration at the operator cab floor and operator seat interface. Qualitative or subjective data, collected with the VAS, allowed researchers to obtain the operators’ immediate impressions of shock, vibration, and discomfort levels for the vehicle ride on each of the seat designs. Each shuttle car operator made six round trips with the vehicle each seat. The shuttle car operator marked the VAS on the first, third, and sixth round trip of the trials for each seat. A round trip consisted of traveling to the coal face with no load and returning to the load discharge location with a full load of coal. Results Total overall average ratings for the five vehicle operators of the mid-coal seam shuttle car, showed that operators sensed from 45 to 87% less discomfort with NIOSH seat designs compared to the existing seat design. Using a 95% CI, researchers computed a strong positive correlation for discomfort. Figure 1 illustrates the RCB analysis method for one of two NIOSH seat designs.

Jan 6, 2006

By J. G. Donaldson

A bench-scale method for recovering lead and zinc from slimes and mill tailings from the Tri-State District of Missouri, Oklahoma, and Kansas was developed by the Bureau of Mines. Dilute hydrochloric acid, containing sodium chloride, and chlorine gas were used to decompose the mineral constituents. Lead was electrolyzed from the pregnant acid solution, and zinc was precipitated from the depleted electrolyte by neutralization with lime. Up to 98 percent of the lead was recovered in an impure lead electro- deposit assaying approximately 85 percent lead. Zinc recoveries up to 90 percent of the total were attained in a precipitate assaying approximately 40 percent zinc.

Jan 1, 1963

By Halagowder Devaraj, Mostafa Sheykhnazari, Veer P. Bhavanandan

"A sensitive colorimetric assay for detecting mucins and glycoproteins rich in 0-glycosidically linked saccharides is reported. The method combines the susceptibility of N-acetylgalactosamine terminating 0-glyco idically linked saccharides to P-elimination with the Morgan-Elson reaction for N-acetylhexosamines with free reducing ends. All mucin and mucin-type glycoproteins but none of the serum-type glycoproteins tested resulted in characteristic color production. All mucins tested gave linear responses in the range 5 to 200 ""g and the assay was also adapted to the microscale involving the use of 96-well microtiter plates. The microassay in which the volumes of samples and reagents are scaled down 2.5-fold was particularly useful in monitoring of mucins, in the presence of other glycoconjugates, in large numbers of samples obtained during fractionation procedures. Cesium chloride, cesium bromide, potassium thiocyanate, and various detergents do not interfere with the colorimetric determination. Guanidine hydrochloride, cesium triftuoroacetate, and B-mercap- . toethanol decreased color by 30 to 45%; however, the interference was not serious to prevent the use of the method for detection of mucins in their presence. The use of the method for the specific detection of mucin during fractionation by gel filtration and density gradient centrifugation of cystic fibrosis sputum samples is demonstrated. Mucins are an important class of biomacromolecules whose structure-function relationship is poorly understood (1,2). The investigations of mucins are hampered by difficulties in purifying these very large size molecules which appear to avidly bind other components of the mucus (3,4). One of the problems during purification is the specific detection of mucins. For example, during the various purification steps, the fractions containing mucins are typically detected by assaying for neutral sugars (hexoses) (5,6), for sialic acids (7), or for periodate oxidizable saccharide units (8). However, these methods are not entirely satisfactory because neutral sugars, sialic acids, and periodate-oxidizable saccharides are also components of other glycoconjugates. In addition, the neutral sugar and sialic acid measurements are also subject to interference from high levels of proteins and nucleic acids."

Jan 1, 1990

By C. W. Morris

This study was performed for the U.S. Bureau of Mines. An existing computer simulation of a dragline was modified to simulate a dragline dumping into the hopper portion of a cross-pit conveyor system. This revised computer model was then used to study four proposed cross-pit conveyor systems. Parameters such as dragline position, hopper position, and digging procedure were varied to maximize the dragline production. This performance was compared with the conventional side-casting spoil method. I t was concluded that the cross-pit conveyor systems were competitive with the conventional side-casting technique.

Jan 1, 1977

By J. P. Hansen

Reducibility tests were run by the Bureau of Mines on an open hearth lump ore and four groups of pellets whose smelting characteristics had been deter-mined previously in the Bureau's experimental blast furnace. When reduction data from various tests were plotted on specially prepared paper l-(l-percent reduction/100)1/3 against time, the plots were linear. The iron-wustite inter-face therefore advances at a constant rate. The rate of the interface advance in mm/min was used as a reducibility index. The reducibility index measured at 900° C, using 0.45 cu ft hydrogen per minute varied inversely with the surface area of the sample. Even with carefully controlled surface areas, how-ever, duplicate reducibility indices varied considerably. When enough tests were run to give a stable mean, the mean reducibility index did correlate with blast furnace production for the four pellet groups. Results indicated that if the interface speed itself were to be used for correlation with blast furnace production, a sample size of about 180 grams of minus 0.742-plus 0.525-inch particles should be used with a test temperature of 900° C and a flow of 0.45 cu ft hydrogen per minute.

Jan 1, 1966

By A. Gene Collins, Cynthia A. Pearson, Cathy J. Waters

The chemistry of selenium and tellurium is discussed , along with a method of preparing a synthetic oilfield brine , an oilfield brine sampling method , and methods for determining selenium and tellurium in complex oilfield brines . Selenium either can be reduced to the elemental form with sulfur dioxide and determined semiquantitatively by color comparison of the red amorphous form or can be converted to selenite and determined quantitatively by reacting it with 3,3 ' - diaminobenzidine and obtaining its spectral absorbance at 420 mu . Tellurium can be reduced to the elemental form with hypophosphorous acid , and the spectral absorbance of its red hydrosol can be measured at 400 mu . Less than 0.05 mg / 1 of selenium and 0.1 mg / 1 of tellurium can be determined by the described methods .

Jan 1, 1964