Search Documents

Alabama ranked 19th in the Nation in nonfuel mineral value1 in 1994, down from 18th in 1993, according to the U.S. Bureau of Mines. The estimated value for 1994 was $576 million, a 2.5% increase over that of 1993. This followed a 3.5% increase in 1993 over that of 1992. The State accounted for a little less than 2% of the U.S. total. Nonfuel mineral production in Alabama consisted entirely of industrial minerals; no metals were mined in the State. Bauxite materials mined in the State are a natural mixture of bauxitic clay and bauxite having very low iron oxide content and are primarily used to make refractory (high temperature resistant) products, rather than in the production of primary aluminum. In descending order of dollar value, the top four mineral commodities produced in Alabama were crushed stone, portland cement, lime, and construction sand and gravel. These commodities accounted for almost 88 % of the State's total non fuel mineral value, while crushed stone and portland cement together represented almost 65 % of the total. In estimated mineral production for 1994, Alabama remained first in common clays and first of only two States that produced bauxite; third in lime, kaolin clays, and fire clays; seventh in portland cement and salt; and was one of the top seven States that produce bentonite clays. The State dropped from third to fifth in masonry cement. Production of talc and pyrophyllite resumed in 1994. Compared with 1993, the value of crushed stone, lime, construction sand and gravel, common clays, kaolin clays, fire clays, bauxite, and talc and pyrophyllite increased. Decreases occurred in portland cement, masonry cement, industrial sand and gravel, and dimension stone.

Jan 1, 1995

By A. Matzick

In its work under the Synthetic Liquid Fuels Program the Bureau of Mines has developed on a 6-ton-a-day-pilot-plant scale a continuous, gravity-feed retort far distilling oil from oil shale. The development work covered by this report was done from January 27, 1950, to January 26, 1952, at the ail-Shale Experiment Station near Rifle, Colo. Over 300 pilot-plant tests were made during the investigation. The basic retort developed has been named the Gas-Combustion retort. In this process, part of the heat for retorting of the shale is generated by burning recycled product gas in a combustion zone within the descending shale bad in the retort. Additional heat is supplied by combustion of the carbonaceous residue remaining in the spent shale after the oil has been distilled. Air for combustion is admitted through an air distributor in the center of the bed at about the mid-point of the retort. Hot gas rising from the combustion zone heats countercurrently the descending raw shale and liberated shale oil by pyrolysis of the shale. After passing through and exchanging heat with the incoming raw shale, the oil is condensed as a fog or mist in the gas, which is withdrawn at the tip of the retort. The cool gas is then piped to an oil-recovery system where the oil is separated from the gas in centrifugal separators or other types of mechanical or electrostatic separators. The hot, spent shale below the combustion zone is cooled by heat exchange with recycle gas, which is a portion of the effluent gas from the oil-recovery system.

Jan 1, 1955

Objective: To provide a safe, practical, cost-effective method for measuring coal rib thickness during highwall mining.

Jul 1, 2008

By M. Didyk

In this report, the application of the PHU/MVS program is demonstrated through the use of a simple but realistic mine ventilation program. The report details, the problem description, the input data required and the various output features of the simulator. The PSU/MVS program is written in Fortran IV for use with IBM 370/168 computers. A version of the program that can be used in CDC computers is also available. A ventilation network consisting of 531 branches, 300 nodes and 5 fans took 48 seconds for solution on The Pennsylvania State University's IBM 370/168 computer. Appendix I of this report is the User?s Manual for the program. Appendices II and III contain the input data listing, and selected output listing for; the application. Appendix IV provides tables for leakage, friction factors and shape factors.

Jan 1, 1977

By Thomas P. Dolley

Building stone, cassiterite, kaolin, gold, lime, and peat were the only commodities mined, The country's main economy was in agriculture, primarily in coffee exports. Tribal violence occurred again, between the Hutu and Tutsi tribes, causing an estimated 50,000 deaths, mainly in rural and mining areas. The inflation and a large deficit continued. The country continued to import cement, fertilizers, oil, and petroleum products. Burundi possessed numerous small gold deposits. The northwest and north-east were the country's two most important gold-bearing regions. A large kaolin deposit was found at Ngozi, and its mining was specified in the fifth 5-year development plan for 1988-1992. In the area of Rugombo, limestone was being explored with the intention of opening a cement plant.

Jan 1, 1990

By John Paul Gries

This Bureau of Mines report reviews the mineral industry of the Black Hills area, including Butte, Custer, Fall River, Lawrence, Meade, and Penning- ton Counties, S. Dak.; and Crook, Niobrara, and Weston Counties, Wyo. It includes discussion of geological occurrence, processing, and potential of 27 commodities that have been produced from the nine-county area. The value of mineral production exceeds $70 million annually. Gold and petroleum account for two-thirds of the total, followed by clays, cement, sand and gravel, and rock. The combined mineral industries annually consume 268 million kilowatts of electrical energy, 933 million Mcf of gas, and 2 million barrels of fuel oil. Water consumption is about 10,000 gallons per minute. About 2,700 persons are employed on a year-round or significant part-time basis.

Jan 1, 1974

By Forrest T. Moyer

The safety record of the coal-mining industry, both anthracite and bituminous, in 1966 was improved over that of 1965 in all general measures of injury experience. The improvement was more pronounced in the anthracite industry. The total of 10,679 disabling work injuries comprised 233 fatal and 10,466 nonfatal injuries, 26 and 692 fewer, respectively, than in 1965. The number of fatalities in 1966 was the lowest annual total since complete records were started in 1910. Similarly, the number of nonfatal injuries in 1966 was lower than in any year since 1930 when such data were first collected.

Jan 1, 1969

By J. Douglas Causey

No mines are active in the Hunter Mountain Wilderness Study Area (WSA), and no mineral resources have been identified in the WSA. However, the Monarch Mine has low potential for silver, copper, tungsten, and gold resources in quartz veins; the Shirley Ann Group and Sal Group have moderate and low potential, respectively, for silver, lead, and copper resources in skarn; claims overlying the Eureka Quartzite have low potential for silica resources; and the Tourmaline N1-4 Prospect has low potential for tourmaline resources in quartz monzonite. Copper, lead, silver, tungsten, molybdenum, wollastonite and garnet occur in skarn zones between monzonitic and carbonate units. Silver, tungsten, and copper also occur in quartz veins within monzonite. Known metallic mineral deposits are small, erratic and discontinuous. The J. 0. Mine, adjacent to the northeast corner of the WSA, may contain as much as 26 million tons of subeconomic wollastonite resources. The crest of an open pit to produce that resource would extend into the WSA. No information exists on geothermal potential because no exploration has been done in the area. No occurrences of energy minerals are known within the WSA.

Jan 1, 1983

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1966

By Harmon E. Keyes

Many organizations, including the Bureau of Mines, have made intensive studies of the application of leaching methods to relatively small low-grade disseminated deposits of copper ores, containing both oxide and sulphide minerals. One of the principal difficulties has been to obtain a solvent that could be made at a low cost and would effectively dissolve the copper minerals. Another drawback has been the high initial cost of a plant and the refined type of mechanism ordinarily required by standard practice for carrying out the leaching cycle. The Bureau of Mines has attempted to develop a cheap and efficient solvent that would especially meet the requirements of smaller plants. (See Bibliography.) It has been known that dilute ferric sulphate-sulphuric acid solution is an excellent solvent for most copper minerals, such as chalcocite, bornite, and oxidized forms, but not for chalcopyrite and certain silicates. A method of producing this solution from sulphurous products and waste liquors was developed by the bureau and tried successfully on a test-plant scale at the Southwest Experiment Station in cooperation with the department of mining and metallurgy, University of Arizona, Tucson, Ariz. However, this work did not involve the actual leaching of ores with the solutions thus produced or the cyclic use of the iron solutions in the regenerator cell. Except for certain laboratory tests, in which known impurities were added, no data were available to show the effect on regeneration if accumulations of impurities were built up in the leaching circuit.

Jan 1, 1930

By M. L. Glenn

The Bureau of Mines is conducting research on Fe-based alloys using Si and Al additions to reduce the Cr required for heat-resisting appli-cations. Part of this research is being done to evaluate alloys containing (8-10)Cr-(10-14)Ni-(0-8.5)Si-(0-4) Al to determine which of these alloys have austenitic structures, as well as fabrication properties and oxidation resistance sufficient to substitute for type 304 stainless steel. Based on initial results, an Fe-lOCr-11Ni-5Si alloy and an Fe-8Cr-13Ni-5Si alloy were selected for evaluation of oxidati.on, stress rupture, and tensile properties. Both alloys have oxidation resistance at 7000 and 8000 C that is better than that of type 304 stainless steel. The stress rupture strengths are less than that of type 304 stainless steel but significantly better than that of commercial heat-resisting steels with similar Cr contents. Yield strengths of the alloys were equivalent to that of type 304. Both alloys had high tensile strengths comparable to those of stainless steels that transform to martensite during straining (e.g., type 301). These alloys have weld-hot-cracking resistance comparable to that of type 304 stainless steel. This initial study shows that Si has potential as a substitute for Cr in stainless steels for heat-resisting applications.

Jan 1, 1984

By F. A. Rutledge

The Bureau of Mines Investigated the Copper Bullion claims at Rua Cove on the east coast of knight Island in Prince William Sound, Alaska, during November-December 1948 and March-April 1949. This project was part of the Bureau of Mines program for developing critical and strategic minerals in Alaska, Mineralization at the copper deposit on the Copper Bullion group of claims is mainly pyrrhotate and chalcopyrite, confined to a northeast-trending shear zone in the greenstone 2,000 feet northwest of Rua Cove. The property has been partly developed by two adits, by a number of crosscuts from the upper adit, and by several diamond-drill holes.

Jan 1, 1953

By Charles A. R. Lambly

This paper, which describes the mining practices of the Pend Oreille Mines & Metals Co. at Metaline Falls, Wash., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in various mining districts of the United States. ACKNOWLEDGMENTS Acknowledgment is made to L. P. Larson, president, and Jens Jensen, secretary, of the Pend Oreille Mines & Metals Co. for permission to publish this paper. information was supplied by E. Berglund, mine superintendent; Earl Miller, chief engineer; Lynn Kinney, John Currie, and Wally Frick, engineers; Arthur Newman, chief clerk; and Jack Crampton, assayer.

Jan 1, 1941

By T. A. Henrie

A technique was devised for measuring the rate of chemical reactions between reactive metals and molten-salt mixtures at high temperatures. The rate of the heterogeneous reaction between high-purity titanium metal and titanium trichloride in molten sodium chloride was determined. The reaction is surface-controlled, and the heat of activation is 8.29 kilocalories per mole TiC13. An active site or reaction nuclei is created by adsorbing a TiC13 molecule at the metal surface. Reaction of the second TiC13 species forms an activated complex that decomposes into three TiC12 molecules.

Jan 1, 1963

By M. R. Yenchek

The U.S. Bureau of Mines designed and constructed sensitive and coordination-free ground-fault relays (GFR's) for use on mine power systems. First, a list of GFR attributes for mine ac utilization applications was compiled. These practical guidelines specified design, construction, transient immunity, reliability, and operating criteria. The time-current characteristics of the ac and dc units, subsequently fabricated, were designed to be below the human electrocution threshold. The significant and highly variable capacitance of high-voltage distribution cables was found to preclude the sensing of ground currents in the milliampere range. However, the coordination-free system developed for high-voltage distribution should enhance safety by significantly decreasing response time to ground faults. Implementation of the sensitive GFR technology in the mining industry has the potential to eliminate the majority of injuries and nearly all the deaths resulting from contact with energized components.

Jan 1, 1990

By Louis A. Turnbull

An investigation of coal deposits near Cerrillos Santa Fe County, N. Mex., was undertaken 14 the Bureau of Mines in 1943 as part of a general program to determine sources of metallurgical coal for western steel plants. Almost all of the coal used for metallurgical purposes west of the Continental Divide Is mined from the Lower Sunnyside bed in, Carbon County,, Utah. Coke used in western steel plants that is produced from Lower Sunnyside a coal is weaker, structurally, than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality then the coal produced from the Sunnyside bed. The objective of investigations of western coals was to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed. and (b) develop; if possible, reserves of coal with coking quantities superior to those of Lower Sunnyside

Jan 1, 1951

By V. F. Parry

This report is the first substantial description of the carbonizing process and the details of experimental work conducted at the Denver laboratories under a coopeative agreement between the Bureau of Mines and the Texas Power & Light Co. It presents the results of tests on several Texas lignites and other typical western coals that have been processed in the first pilot plant operated at Denver. Investigations on drying fine coal in the entrained and fluidized state have been under way at Bureau of Mines Denver laboratories for several years. Reports on this work were published in 1949 and 19505/ describing the theory and practice of re-moving inherent moisture from the lower -rank coals. The investigation did not include a study of the removal of surface moisture from fine fuel. Private industry in Canada became interested in the possibilities of drying fine coal, employing the closed-circuit system and techniques recommended by the Bureau. Large, commercial-scale drying units were built by a Canadian company, which successfully demonstrated that surface moisture could be removed from fine coal at high efficiency and capacity ill drying units similar in design to those developed by the Bureau.

Jan 1, 1953

By G. L. Oldright

In the first Report of Investigations of the present series?(No. 4562) the usual course of progress ill reducing the minerals of low-grade ores to their valuable metallic components had been noted as advancing along two lines to concentrate a usually diminishing percentage of these minerals to a smaller bulk of richer product, and then to smelt the smaller bulk more cheaply per pound of metal produced. Fundamental properties of lead compounds made it difficult to treat much richer lead products than are treated at present in several steps of conventional lead smelting, unless ?marked modifications were made. No limits to the richness of the feed itself' were set by the ore (Scotch) hearth; on the contrary, the richer the feed, the better the results given by the hearth. The natural field of operation of the hearth, as determined by the ores available, was seen to lie in the Central United States, with their lead concentrates containing negligible quantities of precious metals and. with few ores of such metals available for use as fluxes. It was noted) however, that even in its chosen field, the Scotch hearth, or "ore" hearths developed from them, was not always used; the usual smelting practice was followed, at times, of sintering followed by blast-furnace smelting for even rich ores.

Jan 1, 1949

By Richard F. Link, George S. Koch

Through the use of statistical methods, estimates of metal content and tonnage of an ore body made by using data from 18 diamond-drill holes are compared with actual values established with data from 1,829 drift samples. The reliability of the estimates made from the drill holes is assessed in several ways. The relationship of metal content (assay-width product) to grade is explained. It is concluded that useful estimates can be made from 18 drill holes provided that reasonable assumptions are made and certain risks accepted. The ore body investigated is the Don Tomas vein of the Frisco mine, San Francisco del Oro, Chihuahua, Mexico.

Jan 1, 1964

By V. L. Burdick

A literature review of current uses of Mn02 in ceramic applications with suggestions for future research. Historical background, oceanographic distribution, geology, exploitation, law and politics. Uses of Mn02 in ferrites, semiconductors, catalytic processes, thermo-luminescence and photochromic materials. Select bibliography of 33 items, plus 129 references.

Jan 1, 1980