Search Documents

By Irving Wender

The oxo reaction consists of catalytic conversion of olefins by reacting the olefins with CO and H2 (water gas) to aldehydes that contain one more carbon atom than the starting olefin. The aldehydes are then generally reduced with hydrogen to primary alcohols in a second stage. The two-stage process is called the oxo process. The word "oxo" is derived from the German "oxierung" (ketonization); thus the exact English equivalent of "oxo" is "keto". The oxo process may be applied to nearly all olefins. A wide range of pressures and temperatures may be used in both stages. The pressure range usually employed is 150 to 200 atmosheres. The temperature in the first stage is usually about 140° C. and in the second or hydrogenation stage about 180° C. Although a standard Fischer-Tropsch catalyst may be used for both steps, cheaper catalysts have been utilized to effect hydrogenation of the aldehydes. Most of the information for this, report on the oxo process was gathered from Technical Oil Mission microfilms. T.O.M. Reels 14, 55, and 134 were especially valuable. T.O.M. Report 6 by H. M. Weir was very helpful. Information on the oxo process is scattered throughout documents captured in enemy territory, and the present report does not include all the available data. Some of the information was procured by personal interview. Where, in the body of this report, certain investigators are quoted, the source of the statement is either personal interview or the T.O.M. reports.

Jan 1, 1948

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By M. O. Magnuson

This publication describes abandoned-mine fire-control work administered by the Bureau of Mines under cooperative agreements with State and local governments. The work was done by private contractors under the supervision of Bureau engineers. The work is authorized by Public Law 738, approved August 31, 1954, and Public Law 89-4, approved March 9, 1965. Earlier work was authorized by Interior Department Appropriations Acts for fiscal years 1949-55. A total of 70 fires have been controlled under this program in the eastern bituminous region. The nature and extent of the abandoned-mine fire problem in the bituminous region is discussed, and the methods used for controlling these fires are described. The methods that have been used, either singly or in combination, include loading out and cooling the burning material, installing fire barriers, surface sealing, and water and pneumatic flushing.

Jan 1, 1974

By L. Hoogenboom

Under contract (H0232044) to the U.S. Bureau of Mines, Mechanical Technology Incorporated made an experimental investigation of the feasibility of measuring the load in roof bolts using a magnetostrictive sensor. The program was aimed at developing an inexpensive, moderately accurate, load-sensing element suitable for permanent installation and use underground. A combination of a cylindrical load-carrying sleeve under the bolt head and 3 removable circular multipole inductive sensor around the sleeve was tested. Program tasks included: design and fabrication of several sensors; design and manufacture of a large number of experimental sleeves; definition of electronic instrumentation specifications; design and manufacture of electronic sensor readout; and evaluation and testing of many sensor-sleeve combinations. Sleeves of different materials, various lengths, diameters and areas - with and without various nickel coatings -were combined with several experimental inductive sensors that were operated over a wide range of carrier frequencies.

Jan 1, 1974

By Larry L. Anderson

Enormous quantities of organic wastes are produced each year in the United States. The total amount is in excess of 2 billion tons and at least 880 million tons of this is moisture- and ash-free organic material (dry organic solids), representing a potential energy source of significant magnitude that is not being utilized. Bureau of Mines scientists have developed methods for converting these wastes to convenient energy forms. This report itemizes and evaluates for the first time in detail the quantities and sources of moisture- and ash-free organic material contained in manure, urban refuse, industrial wastes, sewage solids, and agricultural wastes in the United States. Furthermore, estimates are presented for amounts of organic wastes collected or concentrated. The potential for fuel, either oil or gas, from both the total organic wastes generated and those collected or concentrated is also estimated.

Jan 1, 1972

By Deborah A. Kramer

This Bureau of Mines report presents a cost estimate of the Bayer process, which is used for virtually all cell-grade alumina production. The report will serve as a reference point to determine the economic merits of processes that have evolved from Bureau of Mines investigations on technology for producing alumina from domestic nonbauxitic raw materials. The Bayer process involves dissolving the alumina present in bauxite in a caustic solution at high temperature and pressure. After the un- dissolved impurities are removed, the solution is seeded to produce an alumina trihydrate precipitate. This precipitate is filtered, washed, and calcined to produce the cell-grade alumina product. This cost estimate is for a plant producing 1 million tons of alumina per year. The estimated operating cost is approximately $250 per ton of alumina.

Jan 1, 1983

By P. D. Kovscek

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted mechanical cutting system to determine the effect of the high-pressure sprays on machine performance, airborne dust levels generated, and size of particles formed. Testing was conducted on a simu-lated coal block (coalcrete) while cutting at a water pressure of 190 psi and at water-jet-assisted pressures ranging from 1,000 to 6,000 psi. The shearer motor energy used by the shearer while cutting coalcrete was determined for each cutting condition. Results indicate that the motor energy required by the shearer for each ton of material cut did not vary significantly as the water pressure was increased. Results of dust measurements recorded near the cutting drum indicate that at water pressures above 3,000 psi, dust reductions up to 85 pct were achieved com-pared with cutting with conventional sprays. Analysis of the particle size distribution during cutting showed that increasing the water pres-sure resulted in increased median particle size. In light of these results, various mechanisms for water-jet-assisted cutting are discussed.

Jan 1, 1986

By M. J. Beus

Researchers at the U.S. Bureau of Mines have developed personal-computer-based data acquisition, instrumentation, and mine visualization and modeling techniques to evaluate a mine accessway in a deep hard-rock mine in northern Idaho. These techniques were applied to a mine shaft in a large silver mine that has been in operation for many years. A very deep, rectangular, timber-supported shaft extending to depths exceeding 2.3 km (7,500 ft) had been deforming continuously as a result of nearby mining, resulting in operational problems. Preliminary visual observations and rock and support monitoring confirmed that severe diagonal distortion was occurring. Extensive field measurements and data analysis confirmed initial observations, provided insights into the cause of deformation, and defined a general approach to structural modeling. Computer analysis of the problem was initiated by developing a three-dimensional model of the terrain. This represented a volume of rock approximately 80 km3 (40 x 1010 ft3) and an area on the surface surrounding the mine 9 km2 (3 square miles). Based on this model, a three-dimensional, finite- element analysis was conducted to establish boundary conditions for sequentially more detailed two- and three-dimensional submodels of the shaft area. Results from the computer study are being used to develop new approaches to mine design and to provide design guidelines for deep mine accessways subject to severe rock-mass loading conditions.

Jan 1, 2010

A series of laboratory evaluations examined the impact of water spray pressure, curtain setback distance, and external and underboom spray use for controlling respirable dust levels and sulfur hexafluoride tracer gas concentrations around a continuous mining machine. This mining machine was equipped with a flooded-bed dust scrubber and was positioned in the box or slab cut. Exhaust line brattice was used for all tests. Dust levels were measured in the return airway and at locations representing the operators of the continuous mining machine and the standard and off-standard shuttle cars. Increasing water pressure or using the underboom sprays produced no significant impacts on dust levels, although their interactions did produce some significant impacts. Increasing curtain setback distance often elevated dust levels, likely by reducing the amount of airflow reaching the face. Use of the external sprays created additional airflow around the mining machine that pushed the dust cloud past the scrubber inlets. This significantly increased dust levels at all sampling locations. Tracer gas levels were measured on the off-curtain and curtain sides of the cutter head and in the return airway. Increasing water pressure generally led to significantly increased gas levels on the curtain side, although a slight decrease was observed on the off-curtain side with the machine in the box cut. Increasing setback distance elevated gas levels on both sides of the cutter head and in the return by limiting the quantity of ventilation airflow reaching the face. Use of the external sprays provided additional airflow along the off-curtain side of the machine, significantly reducing gas levels in this region. These sprays adversely impacted the dilution and removal of gas on the curtain side of the cutter head. Use of the underboom sprays adversely impacted gas levels on both sides of the cutter head. Use of the external sprays provided the best control of respirable dust and face gas concentrations. The smaller increases in miner operator dust levels produced by these sprays were offset by larger reductions in face gas levels on the off-curtain side of the cutter head. Although the underboom sprays minimally impacted respirable dust levels, use of these sprays was not recommended because they increased face gas levels.

Jan 1, 2007

By G. R. Strimbeck

Experimental work is report on the gasification of 90-percent through 200-mesh, strongly coking Sewickley-bed coal with oxygen and with steam in three temperature ranges, namely, 2,700° to 3,400° F., 1,600° to 2,000° F., and 230° to 250° F. Thirty-one runs have been made, during which 56,000 pounds of coal have been charged to the generator at feed rates of 200 to 450 pounds of coal per hour. The average results, not the optimum results, are given in the following tabulation:

Jan 1, 1950

By O. H. Metzger

This is one of a series of capers being published by the Bureau of Mines on gold mining A the Western States. It describes the production of gold in the principal mining districts of New Mexico. The material was gathered red on a trip through tale State in the summer of 1936. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of mine operators in all parts of the State, who willingly contributed all information requested. Geological reports of the Geological Survey and the New. Mexico Bureau of Mince were drawn upon freely for information; credit to individual paper, is given in the text.

Jan 1, 1938

By R. W. Van Dolah

An attempt has been made in this investigation to define the conditions under which ammonium nitrate (AN) might detonate as a result of involvement in fire. The initiation of detonation by shocks derived from explosives or from projectile impact was investigated as a function of temperature and charge diameter. A new technique was devised to investigate the burning of raw and contaminated AN under pressure. No transition, to detonation in AN was obtained in the burning experiments. The critical diameter for detonation of fertilizer-grade AN was found to be quite small when the AN was at temperatures just below melting point; this indicates that initiation of detonation may be less difficult at elevated temperatures but such initiation by gas-phase detonation was shown to be unlikely. Transition from burning to detonation was obtained with AN intimately mixed with fuels that included polyethyl-ene, paper, and fuel oil when these were contained in vessels with restricted vents. However, the experimental results supported by an analytical study indicate that the initiation of detonation in AN from fire exposure in normal storage and from transportation incidents is quite improbable. The detonation of AN in recent incidents more likely may have resulted from the effects of adjacent explosions.

Jan 1, 1966

By John T. Neubert

Between 1988 and 1990, the U.S. Bureau of Mines studied the mineral resources of San Juan National Forest to appraise and determine types and locations of deposits that could be mined economically now and in the foreseeable future. The study included a comprehensive field examination and literature search. Substantial amounts of lead, zinc, copper, gold, and silver have been mined from within the Forest in the La Plata, Rico, Silverton, and Dunton areas. At least one buried 200 million ton stockwork molybdenum deposit occurs in the Rico area. Similar size porphyry copper deposits occur at the surface and about 1,700 feet below the surface in the Bedrock Creek area of the La Plata district. Numerous smaller base-and precious-metal and uranium deposits have been prospected and mined throughout the Forest. Coal, oil, and gas have been or are currently being produced in the western and southern parts of the Forest. Carbon dioxide occurs in the western part of the Forest. Strategic elements occurring within the Forest include platinum, palladium, cadmium, gallium, indium, bismuth, and tellurium; however none of these elements is economically recoverable at present. Several geothermal areas are scattered across the eastern two-thirds of the Forest. Industrial minerals within the Forest include sand and gravel, limestone, and decorative stone.

Jan 1, 1992

By John H. Weitz

Dolomite, heretofore regarded merely as a variety of commonplace limestone, has suddenly attained headline prominence, partly because of the increase in demand for dolomite refractories to line metallurgical furnaces now working at an unprecedented rate of activity, but chiefly because it has become an ore of the light-weight metal, magnesium, needed in vast quantities for the manufacture of war machines. A multitude of inquiries, chiefly from war agencies and prespective operators, for data not only on locations of dolomite deposits but on their size and quality, has made it necessary for the Bureau of Mines to assemble all information available on this important subject. From the Bureau's own records, published information, and correspondence, date on locutions, extent, thickness, accessibility, workability, and chemical composition of high-grade dolomite deposits throughout the United states were accumulated for presentation herein. The report includes about 1,000 tabulations of analyses and a map showing locations of the deposits. The uses of dolomite are discussed in Bureau of Mines Information Circular 7192, "Occurrences and Uses of Dolomite in the United-States," published in 1941. The cordial corporation of many State ecological surveys and various individuals who have contributed information is gratefully acknowledged.

Jan 1, 1942

By M. J. Beus

The Bureau of Mines, under a cooperative agreement with Hecla Mining Co., is conducting a rock mechanics study of the 6,200-ft-deep circu-lar, concrete-lined Silver Shaft in northern Idaho. The objective of the project was to instrument and evaluate lining behavior and rock de-formation when a deep shaft is constructed in a high in situ stress field and anisotropic rock mass. Rock mass displacements were moni-tored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. Field data from the 5,955-ft test level show that rock displacement is controlled by rock mass anisotropy. Liner stress and strain levels reflect the high in situ stress field as well as nearby station and raise construction. Maximum stresses measured in the lining, as a result of shaft excavation, are about one-third of its compressive strength. Subsequent loading pocket excavation resulted in signifi-cantly increased stress and strain levels in the liner. Continued monitoring and preliminary analysis of the data indicate that concrete-lined, circular shafts are stable for the high, unequal horizontal stress fields and rock anisotropy encountered in deep-level mining. Adjacent development work can be expected to significantly alter the initial stress and displacement conditions.

Jan 1, 1984

By Joseph Gersic

The U.S. Bureau of Mines assessed mineral resources of the BLM Malheur-Jordan Resource Areas (MJRAs) in southeastern Oregon in 1993 and 1994. The study relied heavily on acquiring and analyzing existing data. In order to efficiently handle and analyze a large quantity of data, a minerals information management program, informally called MINFO, was developed as a frontend for three databases created to store basic information gathered during the minerals resource assessment. The MINFO program will also provide the BLM with a method of tracking and updating minerals information in the future because program modules in MINFO allow the addition of new data and the correction of errors, creation of print files, transfer of data to other database formats, exportation of data to other software packages, and creation of AutoCAD script files to be used in conjunction with AutoCAD to produce maps. The report specifically identifies significant past and present mineral exploration and development activities and possible areas of future mineral exploration and development. These areas are informally designated as areas of development interest or ADIs. The report contains a scenario of what mineral development might reasonably occur in the foreseeable future if the BLM does not substantially change its present resource management plan, and it shows the possible socioeconomic impacts of that development. The uncertainty of the political and economic situation makes it extremely challenging for the USBM to accurately predict a reasonably foreseeable development scenario. The reasonably foreseeable development (RFD) scenario developed by the USBM for the BLM indicates short-term RFD of minerals should have a negligible socioeconomic impact, and longer-term RFD of minerals should have a slight socioeconomic impact on the MJRAs. The mining industry is facing a rapidly changing business and regulatory environment in Oregon. Several signal changes have occurred recently, including State regulations that require significant bonding prior to the startup of "chemical process" mining, an initiative by a special interest group to stop all chemical process gold mining within the State, and an opinion by the Oregon Attorney General (AG) banning all forms of placer mining without exemption. In the AG opinion, not even gold panning is allowed, and the prohibition applies to mining claims on Federal lands. The State legislature may amend the statute to allow small scale placer mining to occur, as was allowed under an AG opinion issued in 1982. These and other changes occurring at the local, State, and National levels are making it more challenging for the mining industry to operate in the United States. Several epithermal gold properties in the MJRAs attracted the mining industry's interest. Only the Grassy Mountain Project of Newmont Grassy Mountain Corporation may be developed in the next few years. It is probable that at least two other properties will be developed if Grassy Mountain is successful. Mining companies are waiting to see the effect recently promulgated State mining regulations and more stringent proposed regulations, particularly bonding regulations, may have on Grassy Mountain. Resources of bentonite, diatomite, and zeolite are abundant. The almost Ubiquitous stone, sand and gravel, and semiprecious gemstone resources also were examined. Little environmental or socioeconomic impact is expected from reasonably foreseeable development of these mineral resources.

Jan 1, 1994

By Laxman S. Sundae

The Bureau of Mines designed, fabricated, and is using an in-seam tester (1ST) for in situ determination of coal cutting forces. This re-port describes the results of field tests conducted in the Pocahontas No. 3 and Upper Freeport seams to obtain peak and mean cutting forces during coal cutting with several bit geometries, including radial and point attack bits currently used on drum-type machines. Comparisons were also made between new and worn bits, and using data obtained from a Bureau-modified chisel bit. The test results show that longwall plough cutting (horizontal cuts) in bony coal bands (shale) requires >3 times the cutting force for the same cuts in a vertical direction. When no bony coal is present, the cutting forces required to make horizontal and vertical cuts are equal. Worn bits require 4 to 5 times more cutting and normal force than new or undamaged bits. Normal force increased drastically for the worn chisel bit. Peak force encountered in making independent cuts was found to be ~3 times higher than that required to make interactive cuts using a spacing-to-depth-of-cut ratio of 2. Both rake and clearance angles were found to have a significant effect on normal and cutting force.

Jan 1, 1986

By Homer J. Ballinger

During the fall of 1943 and spring of 1944, the Bureau of Mines investigated nine secondary limonite iron-ore deposits in the Williamsville district of Wayne, Butler, and Ripley counties, Mo., by rotary-bucket and power-auger drilling test pitting, and trenching. Studies on beneficiating the ores were made at Bureau laboratories. Iron ore has been mined in Missouri since 1825, and iron mining reached its greatest development between 1870 and 1890. During this period, production averaged about 250,000 tons annually.

Jan 1, 1948

By Robert Lee Stahl

Comprehensive field tests were made by the Bureau of Mines at the Schwartzwalder mine near Golden, Colo., to determine whether surface geophysical techniques could be used to detect and delineate faults in uranium deposits. The tests included seismic refraction, magnetometer, electrical resistivity, airborne infrared thermal scanning, and airborne photography. Of the several geophysical techniques tested in the field, horizontal resistivity profiling with electrode spacings in the range of 10 to 15 feet was most diagnostic of faults. The method is quick, inexpensive, and accurate and can be easily used by mining company personnel to detect and delineate faults.

Jan 1, 1974

The Bureau of Mines conducted a field study to assess the performance of various chain pillar configurations in terms of gate road entry sta-bility. Vibrating wire stressmeters (VWS's) were installed in four consecutive gate road chain pillars. Field data collected during panel retreat were analyzed to gain a better understanding of the mechanics of vertical load redistribution in gate road chain pillars as it relates to ground control problems. Several different pillar configurations were investigated including abutment-yield and yield-abutment-yield designs. VWS data indicate that average pillar loads were lower and appeared abutment-yield pillar arrangement was utilized. port the occurrence of severe roof and pillar to stabilize when an Data analyses also supdeterioration that was visually observed in the tailgate entries during panel extraction.

Jan 1, 1988