Search Documents

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935

By W. L. Dare

This information circular is one of a series published by the Federal Bureau of Mines in which the methods and costs of producing uranium ore on the Colorado Plateau are discussed. This report describes the three largest company-operated uranium mines of Climax Uranium Co. - the G-1, the Mineral Joe, and the Frank No. 1. Climax Uranium Co., a subsidiary of American Metal Climax, Inc., was [corporated] May 11, 1950, just 2 years after establishment of the domestic uranium program by the Atomic Energy Commission. Twenty-five years earlier Arthur H. Bunker, now chairman of the board, American Metal Climax, Inc., organized and operated the U. S. Vanadium Co. at Rifle, Colo.3/ Soon after Climax Uranium Co. was organized, it entered into a contract with the Federal Government to build a uranium-vanadium processing mill in Grand Junction, Colo. Under the contract Climax leased from the Federal Government certain uranium-bearing lands that had been withdrawn from public entry in 1948. From Minerals, Engineering Co. on June 12, 1950, Climax acquired other uranium-vanadium properties on Calamity, Outlaw, and Monogram Mesas in Colorado and on Polar Mesa and in the Yellow Cat area of Utah. To house the milling equipment, Climax leased the old Grand Junction sugarmill building of the Holly Sugar Co. Milling facilities, based on a then new process developed for treating both uranium and vanadium, were completed, and the plant went into production in 1951.

Jan 1, 1959

By Irving Hartmann

As part of the continuing effort by the Bureau of Mines to promote mine safety, research work is being conducted at the Experimental coal mine, Bruceton, Pa., on the prevention of coal-mine explosions and on other mine-safety problems. The principal subjects studied during the past 2 years are briefly described in this paper. Although at present these problems are relevant particularly to the mine layout and to high-speed mining practices in numerous American coal mines, it is hoped that the findings will prove interesting and useful also to our European research colleagues. Some of the investigations treated here will be presented in greater detail in forthcoming Bureau of Mines reports. 1. UNDERGROUND STORAGE OF COAL CUTTINGS The seams in mist American bituminous-coal mines are undercut, shear-cut, or top-cut before blasting. The cuttings arc generally loaded out with the balance of the coal. However, in some mines it is not economical to load and remove cuttings from the mine. This applies especially if the cut section of the seam is of appreciably lower grade than the rest of the coal, or if the cut is made partly into an adjacent stratum that is high in incombustible content. In such mines the cuttings are sometimes stored in random heaps in rooms or other areas, along the ribs of mine entries, or in layers on the floor of rooms or entries.

Jan 1, 1956

By Don B. Hunter

The Bureau of Mines investigated the extraction of alumina from calcined kaolin by leaching with boiling RCI in a train of three 50-gal continuous, stirred reactors. Slurry discharged from the reactors con-tained an excessive amount of fines, which impeded solid-liquid separation. Autogenous grinding of coarse solids that accumulated in the reactors was the source of the fines. This report describes modifications to the reactors and to the operations that led to decreased fines generation and improved solid-liquid separation. Modifications to the reactors included custom-made impellers, the addition of a baffle system, a subsurface slurry discharge system, and slower rotation of the impellers. Concurrent testing of a continuous horizontal belt filter showed that the form filtration rates were increased from 350 to almost 1,000 Ib/h+ ft-2 when the modified reactors were used.

Jan 1, 1984

By Irving Hartmann

The Bureau of Minas has been charged by the Congress with the responsibility for administrating the provisions of the Federal Coal-Mine Safety Act. One of the important duties of bureau inspectors under this act is to determine whether proper measures are taken to prevent mine explosions, which in moat miner includes Judea adequate rock dusting The investigation made after the explosion in Orient No. 2 mine, December 21, 1951, showed that much information is lacking on the adequacy of current rock-dusting and duet-sampling practices in the United States. To obtain such information, an intensive sampling survey was conducted by the Bureau in an Indiana coal mine. This paper summarizes the more Important findings from this survey, describes special samplings at several Pennsylvania coal miners, and discusses related studies in the Bureau's Experimental coal mine.

Jan 1, 1954

By Raymond B. Ladoo

"The talc and soapstone deposits of Vermont have been worked more or less continuously for nearly 100 years, but all of the early efforts seem to have been directed toward the production of slabs for foot warmer, and other similar uses. Altho soapstone of good quality occurs at several places, much of the material first utilized was really talc and was not massive enough to be cut successfully. The grinding of talc in Vermont seems to have commenced in about 1902 and has shown continuous growth since that time. Statistics compiled by the Geological Survey in Mineral Resources of the ,United States show that the production of talc in Vermont has increased, from 8,978 short tons valued at $65,525 in 1905 to 93,960 short tons valued at $625,150 in 1917. Until 1917, New York was the leading producer in both tonnage and value with Vermont second, but in 1917, Vermont took the lead in tonnage produced, although not in value, with a production of over 47% of the total tonnage produced in the United States and over 35% of the world's pro-duction. This increase in production will probably be continued, though possibly at decreased rate, for the reserves of talc In Vermont are large.Active talc mines and mills in Vermont are found in four districts: Chester, Windsor County; Rochester, Windsor County; Waterbury, Washington County; and Johnson, Lamoille County, These mines and mills are distributed as shown in the following table:While there are a great many other known deposits of talc and soapstone in Vermont, some of which have been worked, those listed above are the only ones which have survived and are producing on a commercial basis. The closing down of many mines and quarries, for example, those at Perkinsville, Stockbridge, Reading, Cavendish, and Athens, has been attributed to several causes. Of these causes the most important seem to be exhaustion of the deposit, poor grade, long haul to the railroad, poor management due to lack of knowledge of mining methods and failure to consider talc mining strictly as a business proposition. The companies which are now operating with greatest apparent success are those which have realized the present and future possibilities of their industry, and have invested sufficient capital in both equipment and personnel to establish their companies on a firm business basis."

Sep 1, 1919

By Frank J. Wiebelt, Spangler Ricker

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on.the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these toles, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

By F. S. Crawford

Although it may be impracticable to adopt standard methods of safe working in all branches of mining, and although it may be impossible to establish a standard for each class of work at each mine, some of the iron-mining companies in the Lake Superior district have found that by adopting certain standard ways of performing certain of their operations they insure both more efficient and safer working conditions. Many companies have adopted the idea that the safe way of doing things is also the most efficient and economical way, and, through the medium of their safety conferences they are trying to find the safest way, and the most efficient way, of performing practically every operation about the mines. This activity will, undoubtedly, be continued at every operation which uses this method of doing safety work, because in the advance of industry changes must be made in the results required from time to time. A review of the safety standards and safety suggestions which have been arrived at by some of the companies in this the greatest iron-mining district in the world, will be of value to companies who are interested in improving the safety of their working conditions. So that attention may be directed to the methods in use, rather than to individual companies, all names have been omitted and companies are referred to only by letter.

Aug 1, 1931

By J. T. Popp, C. M. McCulloch

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con- tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By F. B. TOUCH

This bulletin deals with a topic that is exceedingly wide, and will doubtl~ be under consideration and discussion so long as there are enough known deposits of oil and gas remaining in the earth to make their revelopment profitable. The Bureau of Mines has repeatedly called attention to the importance of protecting oil or gas sands from the encroachment of water, and the purpose of this paper is to summarize existing knowledge of methods and devices. Water may gain access to an oil-bearing formation from several sources-from water sands above or below those. containing the oil, or by encroaching through the oil sands as the oil is withdrawn. In short, it may enter a well from the "top, bottom, or side." Such ingress of water is a most serious detriment to the recovery of oil from the ground. As the art of drilling and developing oil properties has progressed, increasing thought, labor, and money have been expended on various methods, devices, and equipment for arresting the migration of water from its normal subsurface position into the porous strata containing valuable oil or gas accumulations. At an early stage in the oil-field development of California, it became evident that considerable modification of accepted drilling practices was necessary in order to meet the conditions imposed by the poorly consolidated shale, clay, sand, and bowlder beds penetrated, as well as the hard layers of sandstone and calcareous shale, which vary greatly in thickness, hardness, and frequency. These hard streaks are commonly called " shell," and are so reported in the well logs. As deeper and deeper territory was prospected, drillers from the older fields of the Ea,st, as well as from Texas and Louisiana fields, took part in the operations. Xhe practice evolved was thus based on the wide experience of a most cosmopolitan group of men who, considered as a group, were not hampered by being limited to the knowledge of the practice at any one locality.

Jan 1, 1918

By N. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract J0377014, "Development and Evaluation of Noise Control Techniques for Taconite Processing Equipment." Three areas of taconite processing equipment, grinding mills, fine screens, and crusher screens have been investigated. Extensive noise and vibration measurements have been made on grinding mills in which the process parameters that affect mill noise have been identified, and the level of shell impact noise around the mill defined. A multiplexing telemetry system was used to obtain shell vibration measurements from a rotating mill. Mill noise control methods were investigated and a partial mill barrier was built and tested on a semi-autogeneous mill. A noise reduction of approximately 3 to 6 dBA was achieved on the falling side of the mill. The use of rubber mill liners on autogenous mills has been evaluated. The noise sources on fine screens have been quantified, and noise control treatments developed. Noise reductions of 11 to 13 dBA were achieved at positions around the fine screen and some in-service testing has been done. Noise measurents of crusher screens were obtained and noise control through resilient screen decks appears to hold the most promise. Additional benefits might be lower life-cycle cost, since the service life of resilient decks is claimed to be longer than steel.

Jan 1, 1983

By M. M. Wong

Electrolysis of titanium carbide and a material consisting of titanium, carbon, nitrogen, and oxygen as soluble anodes in Used electrolytes was investigated by the Bureau of Mines for the preparation of crude titanium metal. Tests made in all-chloride electrolytes showed only a low recovery of titanium as well as a substantial volatilization of titanium trichloride (TiC13) when present in the electrolyte. Electrolysis at 750° to 850° C in a mixture containing 85 percent NaC1-15 percent potassium floutitanate (K2TiF6) yielded as high as 91 percent recovery of titanium from titanium carbide and 62 percent recovery of titanium from the titanium-carbon-nitrogen-oxygen material. Problems associated with the preparation of crude metal by fused-salt electrolysis are discussed. The crude metals produced from both anode materials were electrorefined in a sodium chloride-titanium chloride (NaCl-TiC12) electrolyte, and ductile titanium metal was obtained.

Jan 1, 1963

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines to evaluate the effectiveness of 10 additives to inhibit the self-heating of coal. Aqueous additive solutions were applied to a bituminous coal with a high spontaneous combustion potential, and the minimum self-heating temperatures (SHT's) of the dried coal-additive mixtures were determined in the Bureau's adiabatic heating oven. The relative effectiveness of the additives was determined by the observed changes in the minimum SHT's of the mixtures, or by the time required for the sample temperature to reach 150" C, compared with the untreated coal and a coal-water blank. Sodium nitrate, sodium chloride, and calcium carbonate were found to be the most effective inhibitors, followed by ammonium dihydrogen phosphate, calcium chloride, ammonium chloride, sodium acetate, and potassium chloride. Two additives, sodium formate and sodium phosphate, promoted the self-heating process. Differential scanning calorimetry experiments on the coal-additive mixtures showed that reactions occurred between the coal and some of the additives, but these reactions did not influence the self-heating process.

Jan 1, 1988

By Richard C. Ballance

Fly ash from four sources and in certain proportions was shown to assist chemical coagulation of turbid water and settling of chemically induced floc. Fly ash reduced the time required to form the first visible floc, promoted more uniform flocs about 2 mm in diameter, and increased the mean settling rate of floc particles. Also, the addition of fly ash produced denser sludges than those obtained with alum alone. Final turbidities were independent of fly ash particle size and carbon content. Optimum proportions of fly ash additive are given.

Jan 1, 1966

By R. Stefanko

The industrial hygiene and safety aspects with internal combustion engine in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. Mathematical models of the dilution and dispersion of diesel exhaust contaminants can be useful only if these models can be validated. In this research report, experiments that were specially designed for the above purpose are described. These experiments were conducted in the U.S. Bureau of Mines, Safety Research Coal Mine, in Bruceton, Pa. On the basis of this study, the data collected, and further review of available literature, it is concluded that mathematical models of dilution and dispersion are useful tools for mine ventilation planning. Additional objectives of this study about which conclusions and recommendations are reported here include: (a) evaluation of mine atmosphere contaminant monitoring systems; (b) optimum sampling site locations; (c) model sensitivity and error analyses; (d) computer coding of mathematical models; and (e) development of a diesel bibliography. While an extensive bibliography on diesels is provided in this report, Volume II of this final report has 511 references.

Jan 1, 1977

By E. J. Matson

"The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Projects were set up on only the most promising properties.A preliminary examination of the Mount Hope mine was made in January 1943 by the Bureau's engineers, who recommended exploration by diamond drilling.The mine is in the unsurveyed portion of T. 22 N., R. 1 E., Mount Diablo base and meridian, south-central Eureka County, Nevada, 25 miles by road north of the village of Eureka. A partly graded and Graveled secondary road connects the mine and Eureka on U. S. Highway 50.Extensive sampling was done by the Bureau in February. 1943. Core drilling from the surface was started on March 15, 1944, and completed on April 2, 1545. The 16 holes drilled totaled 7,215 feet. The mining company also did extensive underground core drilling from April 21, 1944, to January 4, 1945. This report gives the results of core drilling supervised by the Bureau of Mines.The drilling program was designed to explore for extensions of the mineralization exposed in the mine workings. As a result of drilling, additional ore was found, and it is believed that this project has fulfilled the purpose for which it was planned.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization, of our mineral resources to the end that they make the greatest possible contribution to na¬tional security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples of ore and performs beneficiation test. Both these branches are under the supervision of Dr. R. S. Dean, assists director.With respect to this report special acknowledgment is due to Charles W. Merriam of the United States Geological Survey for his interpretation of the Mount Hope mine Geology and his cooperation throughout the project; Col. Leverett Davis, former lessee of the property; K. K. Hood, manager of the Mount Hope Unit, Callahan Zinc-Lead Co., Inc.; C. P. Knaebel, assistant manager, and M. P. Nackowski, geologist, of that company, for their help, and to the Sullivan Machinery Co. for its assistance."

Aug 1, 1946

By W. H. Blackburn

This paper describing the milling practice at the Tybo concentrator is one of a series of similar papers being prepared by the United States Bureau of Mines on milling methods and costs at the various mills in the United States. ACKNOWLEDGMENT A large part of this paper way prepared by H. M. Lewers, mill superintendent of the Tybo plant of the Treadwell Yukon Co., Ltd.

Jan 1, 1931

By Paul M. Tyler

Graphite occurs in many places in the United States, but previous to 1914 the domestic production amounted to only 15 to 20 per cent of the natural graphite consumed in this country. Including artificial, graphite, the proportion was about 25 per cent. During the World War the production of both natural and artificial graphite increased until, in 1918 it, contributed more than one-half of the available supply, and since 1919 the proportion has not fallen below 40 per cent. Except during the war period, however, this apparently increasing independence has not been due to any large increase in production from domestic mines. It simply reflects a larger output of artificial graphite and reduced imports of Ceylon lung and chip, grades which have never been produced in substantial quantity in the United States. DOMESTIC DEPOSITS3 American graphite deposits, though numerous and often large, are characteristically low-grade. They constitute an abundant source of potential supply, but in normal times they have proved relatively costly to work, and even at the same price the various products have never been able wholly to displace certain imported qualities, notably crucible grades from Ceylon and pencil graphite from Mexico.

Jan 1, 1929

By E. C. Perkins

Preliminary experiments are reported utilizing bacteria to leach manganese from a variety of domestic low grade manganiferous materials. In two large leaches manganese extraction ranged from 71.7 to 92.5 percent, and the products analyzed over 48 percent manganese. Nutrient requirements and leaching time experiments were made. The mechanism of leaching is not understood, but is different than the mechanism encountered in the microorganism accelerated leaching of copper in the presence of sulfide minerals.

Jan 1, 1962

By E. J. Matson

This report covers the investigation of the MacArthur copper deposit and several adjacent claims in the Mason mining district; Lyon County, Nev. (fig. 1). As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a project was begun first on the MacArthur claims. Work was done later on some adjacent claims in the immediate area, as shown by figure 2. Field work was begun by the Bureau of Mines on January 16, 1950, and completed on October 25, 1950. Eight diamond-drill holes were completed, for an aggregate of 3,414 linear feet, Analyses were made of' each drilling interval. The report includes a brief history of the district and a description of the deposits and of the work done by the Bureau of Mines.

Jan 1, 1952