Search Documents

By Peter D. Lohn

The Bureau of Mines conducted both laboratory and field investigations to study the effectiveness of medium-pressure (up to 30,000 psi) water jets in controlling the generation of airborne respirable dust during the hydraulic fragmentation of coal. Laboratory studies were conducted at the Farmington High Energy Test Site of the Twin Cities Mining Research Center, and field studies were carried out at the Humphrey No. 7 mine, Mount Morris, Pa., in the Pittsburgh coalbed. The water jets were produced by commercially available triplex pumps. The dust samples were collected by midget impinger samplers, and analyzed by electronic and optical counting techniques. Respirable dust concentration for a full-scale production model was projected at below 2 mg/m3, the maximum exposure allowed by the Federal Coal Mine Health and Safety Act of 1969.

Jan 1, 1975

By R. R. Sayers

"Health hazards in the mining industry may be attributed to (1) abnormal conditions of the air, (2) improper sewage disposal, (3) bad drinking water, (4) bad illumination, and (5) local mechanical irritation.Abnormal conditions of the air may be due either to physical or chemical changes. The physical changes are (1) abnormal temperature, (2) abnormal humidity, (3) air movement, and (4) presence of dusts. Dusts may be either poisonous, as salts of lead, arsenic, zinc, or mercury; or nonpoisonous, as dust from coal, silica or quartz, limestone, gypsum, or silicates. Chemical changes may be due to changes in the normal constituents, as lowered oxygen or increased carbon dioxide; or to the addition of abnormal constituents, as carbon monoxide (white damp), hydrogen sulphide (stink damp), sulphur dioxide, methane (marsh gas, fire damp), hydrogen, and nitrogen.Effects of High Temperatures and Humidities The effects of various temperatures and relative humidities have been studied in mines in many countries. Harrington and myself studied them in the metal mines of this country and, in a report written recently, they have been summarized as follows:A. Remaining at rest in saturated air at 91 1/2° F, for one hour, With no air movement caused -1. An increase in body temperature;2. A moderate increase in pulse rate;3. Profuse sweating;4. After effects of dizziness and weakness with air movement caused ¬1. Slight or no increase in body temperature"

Dec 1, 1924

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 13,374 acres of the 14,994-acre Ireteba Peaks Wilderness Study Area (NV-050-438) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, about 4 miles south of Nelson, NV. No identified resources were found within the Ireteba Peaks study area, although there are identified subeconomic resources just outside of the study area boundary. Most of the area is underlain by Tertiary granitic rocks, which apparently postdate mineralization. The area is virtually surrounded by mining districts with mines developed in older rock units. On the north side, quartz monzonite, volcanic tuff, and tuffaceous sediments in the Eldorado mining district host deposits of gold, silver, copper, zinc, and mercury. On the south side, Precambrian gneiss, intrusive andesite porphyry, and hornfels in contact with Quartz monzonite in the Searchlight mining district host gold, silver, copper, and lead deposits. The Newberry mining district to the southeast had copper, gold, and silver mineralization in Precambrian gneiss and andesite.

Jan 1, 1988

By John D. Sullivan

The recovery of copper by leaching from relatively low grade ores containing both oxidized and sulphide minerals is rapidly gaining in commercial importance. There is an economic limit below which certain ores can not be treated by concentration methods, and material with values below this limit must be discarded, possibly to be treated later, or the copper must be extracted by wet processes. Heap leaching has been carried out by the Phelps Dodge Corporation, Copper Queen Branch, for several years, and to-day its plant is a large producing unit. The Ohio Copper Coy at Bingham, Utah; has been leaching in place since 1919. Many other leaching operations are also being; carried out in various parts of the United States and in foreign countries. The plant at Rio Tinto, Spain, may be considered the father of heap leaching.

Jan 1, 1931

By Emory Smith

The Victorville cement plant of the Southwestern Portland Cement Co. is located about 1 mile from the city of Victorville, Calif. Two transcontinental railway systems, the Atchison, Topeka & Santa Fe, and the Southern Pacific Railroad, afford shipped facilities. The plant is modern and well kept, as the officials, especially the higher operating officials, take pride in the appearance of the place. Dust has been practically eliminated by the installation of dust collectors and wet grinding. The plant has a rated capacity of 5,000 barrels of cement daily.

Jan 1, 1929

According to industry representatives, U.S. producers were listing unalloyed 95.5 percent aluminum ingot in October at 53-57.5 cents per pound, but reportedly much is being priced at 53 cents. New York dealers raised their October positions by about 3 cents to 56-56.5 cents, mainly to cover spot supply shortages. London Metal Exchange 3-month forward contracts traded up in October from 52.3 to 57.3 cents per pound and closed at 56.4 cents. ASBESTOS The Jaquays Asbestos Corp. has announced the imminent closure of its mine and mill in Globe, Arizona. This is the last asbestos producer in the State having operated continuously, except during the early thirties, since 1914. Cost of compliance with environmental regulations was given as the reason for closure.

Jan 1, 1978

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By F. E. Spencer

Calculated equilibrium data are presented for three phases in the flue gas stream from a hypothetical open cycle MHD generator. A typical coal is "burned" with 1.0 gram-mole K2O seed per kilogram coal and with 101 percent of stoichiometric air. Tables of composition and the overt thermodynamic properties, enthalpy and entropy, are given for the temperatures 2200 (-100) 1100 kelvins, pressures 1.0 and 1.5 atmospheres, and slag rejection figures of 90 and 75 percent.

Jan 1, 1973

By Terrence J. Stobbe

The authors investigated the nature, cause and treatment of 234 back injuries which occurred in 156 different situations in underground coal mines. A detailed interview was conducted with each injured miner as 137 variables were explored to provide a complete picture of the injury scenario. The miners worked at 23 mines in six states. An important finding of the study was that sudden movement, which occurred in 527 of the injuries, is a more frequent factor than heavy lifting in causing hack injuries. Along with sudden movement, other major injury causing factors were equipment seat design, lifting, cable handling, and slips/trips. No significant differences were found between the injury scenarios associated with lost time and non-lost time injuries; thus, both sets of scenarios should he used in doe loping back injury control strategies. Medical treatment and rehabilitation varied in content and quality. Dialogue between the medical, rehabilitation and mining communities is needed to develop an effective treatment strategy. Back injury control related training was found to be inadequate in most mines. Mine specific training for physical stress recognition and potential sudden torte release should he added to the training currently given. Based on the information collected in this study, recommendations were made regarding equipment design, mechanical assists and procedures for material handling, training, etc., which, if implemented, will assist in reducing the frequency of back injuries in underground coal mining.

Jan 1, 1989

By K. O. Bennington

The thermodynamic properties of hedenbergite, of composition [(Ca0,9516) (Mg0,0583Fe2+0.7134 Fe3+0.0934 Mn0,1366) (Si206)], were experimentally determined at the Bureau of Mines. The standard enthalpy of formation determined by hydrofluoric acid solution calorimetry is AHf298 = -680.96±0.855 kcal/mol. The standard enthalpy of formation from the oxides is AR-96 = -24.55±0.485 kcal/mol. Low-temperature heat capacities were determined by adiabatic calorimetry from 12.3 to 300.1 K. The derived standard entropy is S-98 - 41.218±0.148 cal/mol-K. High-temperature heat capacities were measured with a differential scanning calorim¬eter from 397 to 1,147 K. These experimentally determined data were combined with data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation are given as a function of temperature. The standard Gibbs energy of formation at 298.15 K is AGf298 = -641.90±0.86 kcal/mol.

Jan 1, 1984

By R. C. Hickman

Preliminary evidence indicated that the Chattanooga Shale might constitute a potential vast low-grade source of uranium. Investigation by core drilling indicated that while the Chattanooga Shale may constitute a resource for the future, the very low (0.006 percent) average uranium content is not economic when compared with the relatively higher grade western ores. A total of approximately 12,000 feet of test drilling was done in 72 drillholes, and large samples were mined for extractive and metallurgical testing. An experimental mine site was selected on the basis of the drilling project.

Jan 1, 1967

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By Robert G. Bottge

Hard rock mining has grown in importance in the Yukon Territory during the last 10 years while Alaskan hard rock mining has declined. One asbestos deposit in Alaska is dormant, but an asbestos deposit 55 miles to the east in the Yukon Territory is being mined by the Clinton Mine Div., Cassiar Asbestos Corp., Ltd. In this Bureau of Mines report, the economics of mining in the two locations were derived using the Clinton mine as a model. Both deposits were assumed to be of equal size and mined by similar methods. Conventional open pit mining and processing methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The estimated cost for the mine, mill, and support facilities in Alaska was about 30 percent more expensive than that in the Yukon Territory. The higher labor rates in Alaska were the primary contributor to the higher construction costs; freight rates added only slightly to the total costs. Approximately two-thirds of the additional annual costs of operating in Alaska were for wages and fringe benefits. The price required for the Alaskan asbestos fiber was $356.65 per ton compared with $287.44 for Yukon fiber, plus or minus 20 percent. A 12 percent discounted cash flow rate of return, 100 percent equity financing, and a rapid writeoff of assets were assumed.

Jan 1, 1975

By L. M. Adams

Experiments in reclaiming acidic surface-mined coal lands with raw fly ash from bituminous-coal-fired powerplants were conducted by the Bureau of Mines at two sites in northern West Virginia. Plots at both sites were treated with varying tonnages of fly ash from three area powerplants and were planted with a variety of grasses, legumes, trees, and shrubs. Eight grasses and seven legumes were investigated. Greatest promise for growth under harsh soil conditions was shown by Kentucky 31 fescue, rye and red top grasses, and birdsfoot trefoil, a legume. Survival of trees and shrubs was negligible. Addition of fly ash to the spoil increased the pH to a range tolerable to some types of plant growth, improved the texture of the soil, and increased the available water of the resulting mixture.

Jan 1, 1971

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

By W. R. Huff

This report describes the development and operation by the Bureau of Mines of a pilot plant designed for using high-volatile A bituminous coal-in-water suspensions as a source of preheated coal and superheated steam in the pressure gasification of coal with oxygen. Figure 1 on page 2 is a block diagram of the integrated gasification process, in which a total of 70 tons of coal was fed from slurry and gasified. The present work included (1) development of equipment and methods both for mixing pulverized coal and water to produce slurry and for pumping and metering the slurry at gasification pressure; (2) development of equipment for heating the flowing slurry and, because slurry that can be pumped produces more steam than is necessary as a gasification reactant, developing equipment for removing and metering the excess steam; and (3) demonstration of the process under actual gasifier operating conditions, at a coal rate of about 800 pounds per hour and gasification pressures in the range 100 to 300 pounds per square inch gage. By using the forced-convection principle, a flow of slurry made from a caking, high-volatile A bituminous coal can be continuously heated to 600° F. in a coil-type heater. The flow rate and concentration of the slurry and the temperature gradient along the length of the heating coil must be closely controlled. In a radiant-type heater, involuntary reductions in flow rate, even momentary, can lead to coking and plugging of the heater coil.

Jan 1, 1961

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 15,174-acre Sleeping Giant study area, including the 6,112-acre Wilderness Study Area (MT-075-111), in order to evaluate its identified mineral resources. The study area is located in Lewis and Clark County, MT, about 30 miles north of Helena. Sleeping Giant Mountain trends west-northwest from the Missouri to the eastern crest of Little Prickly Pear Canyon (the route of Interstate 15), and has several summits over 6,000 ft. Geologically, the area is in the Disturbed Belt, and a large block of Middle Precambrian metasedimentary siltstone and underlying shale has been thrust northeast over younger, sedimentdry volcanic and intrusive rocks.

Jan 1, 1988

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

By Robert S. Sanford

In April 1948, the Bureau of Mines was requested to evaluate the graphite deposit' known as the Benjamin Franklin and Just mines in Chester County, Pa. After preliminary investigation, it was recommended that the Bureau core-drill, trench, and sample the deposit and make beneficiation tests on the ore. During the first and second World Wars, flake graphite was in short supply, and a number of deposits in the United States were exploited. In 1942, the Defense Plant Corporation, through its lessee, the Benjamin Franklin Graphite Co., purchased 70.263 acres of graphite-bearing land and built a complete mining and milling plant with a capacity of 300 tons of crude ore per 24-hour day at a cost of $426,250 (Plancor No. 1254).

Jan 1, 1949