Search Documents

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By J. W. Paul

A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and discusses regulations and practices which have resulted in a low-frequency rates from falls of roof and coal in a few representative mines, takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of Western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, gross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat, and the block system are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some goad may accrue to many other bituminous mines which have similar natural conditions.

Jan 1, 1933

By Tobias W. Goodman

The U.S. Bureau of Mines used a contact drilling strategy with short-collared assemblies in order to rotary drill long horizontal methane drainage holes in the Beckley Coalbed near Glen Daniel, WV. By decreasing the thrust, and increasing the rotation of the drill bit when in contact with the roof and floor rock, assemblies with 1-ft (0.3-m), 10-ft (3- m), and 144 (43-m) long collars were made in deflect and stay in the coalbed. Successful application of this procedure resulted in holes drilled full length in coal with the original assembly including bit. The test assemblies deflected away from the original bearings of the holes during drilling and arced. Four holes were drilled to depths ranging from 478 ft (145.7 m) before the strategy was developed, to 4,034 ft (1,230 m) when the strategy was applied. Total length of the holes in coal was 8,590 ft (2,618 m). After 577 days the total methane captured by the holes was 221,600,000 ft? (6,276,000 m3). The methane flow rate peaked at 805,000 ft3/d (22,798 m3/d), then decreased to stabilize at 670,000 ft?/d (18,974 m3/d) after 6 months.

Jan 1, 1989

By T. L. Turner, Daniel T. Rogers

As part of a program to investigate technology for the extraction of studied HNO3 alumina from abundant domestic ores , the Bureau of Mines leaching of calcined Georgia kaolinitic clay . In this investigation , iron impurities were removed from the aluminum nitrate pregnant leach liquor by solvent extraction , and the purified liquor was evaporated to prepare a suitably concentrated crystallizer feed liquor . Aluminum nitrate nonahydrate was crystallized from the liquor to separate the aluminum from undesirable trace elements and excess water . Continuous crystallization at 40 ° C in a pilot plant vacuum evaporative unit was performed for 5 days to observe the effects of impurity buildup under minimum bleed- stream conditions . Liquor feed rate was 26 lb/h and AAll (( NNOO33 )) 33..99HH22O0 ((AANNNN)) crystal production rate was 17 lb/h . Fe 203 and Cr203 were not effectively separated from the crystals , and P205 , MgO , and K20 impurities must be removed by recrystallization . Other impurities did not excessively contaminate the crystals . Washing the crystals with water or aqueous HNO3 gave an equivalent increase in crystal purity levels by displacing mother liquor . Theoretical equations , applicable to any continuous evaporative crystallization of developed to produce material balances for engineering ANN , were applications .

Jan 1, 1965

By John G. Kovac

A computer simulation has been developed to estimate the chances of a miner making a successful escape while wearing a SCSR. The model takes into account: (1) training in the use of SCSRs, (2) apparatus integrity, and (3) the oxygen cost of a mine escape. This Bureau of Mines report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for Zambia for the period from 1970 through 1981. The work done through the Bureau of' Mines, Minerals Availability Program, under Contract number J0225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) timber and lumber, 6) fuel, 7) powder and blasting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By L. A. Morley

This report summarizes the work performed on Bureau of Mines Contract J0199106, "Portable Trailing Cables, Splices, and Couplers - Design and Installation Considerations," from May 1, 1979 until December 31, 1981. Splice installations and considerations for the possible use of conductive-rubber shielding in low-voltage trailing cables as well as coupler installations in high-voltage cables were the principal tasks. Flammability measurements on cable components and general testing facilities for mine electrical equipment were secondary tasks. Theoretical and empirical data indicate that conductive rubber with high resistivity values is an unsatisfactory shield design for current-sensing fault detection. Elimination of partial discharge in coupler installations requires meticulous care.

Jan 1, 1982

By S. C. Termes

The Bureau of Mines conducted research on the flocculation of various minerals with insoluble cross-linked starch xanthate (ISX) to determine its potential as a beneficiation technique for low-grade, highly dissem-inated ores and for selective desliming. Covellite, chalcocite, pyrite, pyrrhotite, chalcopyrite, bornite, sphalerite, galena, and molybdenite fines flocculate with ISX. Floc formation, floc size, and settling rate are dependent on pH, with the pH dependence differing for each mineral. Quartz is not flocculated by ISX. Experiments to obtain selective flocculation of sulfides from quartz were attempted. Good selectivity was only obtained for the bornite-quartz system. postflocculation separations resulted in flocculated bornite in grades as high as 92 pet. Evidence is presented that the flocculation of many of the sulfide minerals with ISX may involve covalent bonding of the xanthate group to lattice metal site(s).

Jan 1, 1983

By J. W. Paul

[A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and, discusses regulations and practices which have resulted in a low frequency rate from falls of roof and coal in a few representative mines takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, cross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat and the block systems are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some good may accrue to many other bituminous mines which 'nave similar natural conditions.]

Jan 1, 1933

By Roy H. Poston

The following paper is one of a series on mining methods and practices being published by the United States Bureau of Mines, and deals with the sinking of the Pim shaft (No. 7) of the St. Louis Smelting and Refining Works of the National Lead Co. in the southeast Missouri lead belt. The shaft was sunk in 1922 and 1923 on a tract several miles south of the company's main plant located at St. Francois, Mo., in St. Francois County. The author is indebted to W. H. Comins, local manager of the company, with whose permission this article has been written, for his helpful criticism; and to E. T. Campbell, geologist, and M. Cross, underground shop foreman; and to W. A. Cole, manager of the E. J. Longyear Development Co., who had general supervision of the work and supplied detailed performance and cost data.

Jan 1, 1932

? A roof bolter reaches for a lever while guiding the drill with his other hand. Since he's watching the drill and many of the controls look and feel alike, he hits the wrong control and crushes his hand. ? Six hours into the night shift, an ore truck driver dozes off. The truck plows over the berm and down into the pit. ? Fleeing a afire, a face crew sees smoke in the intake entry. Assuming the fire is ahead, they cross over to another entry, but soon encounter even worse smoke. These very different accidents have at least one factor in common: the human factor. The actions, decisions, thoughts, or perceptions of one or more humans contributed to the accident. These are just a few examples of safety problems researched by the Human Factors Group of the Pittsburgh Research Center, U.S. Department of Energy.

Jan 1, 1998

By G. Schuman

Variations in pyrite reactivity are known to exist within samples collected from different areas. Using samples collected from acid and non-acid sites, the relationship between the factors affecting pyrite oxidation and observed variations in pyrite reactivity was studied. Heavy liquid separations were used to extract the pyrite from nine pulverized rock, coal, and coal refuse samples. Simulated weathering tests were used to determine the degree of reactivity of the extracted pyritic material. Representative portions of each pyritic sample were analyzed for whole rock composition (including pyritic sulfur and neutralization potential), for elemental composition, and by x-ray diffractometry. The samples were also examined with reflected light microscopy to ascertain pyrite morphology distributions. Tests for the presence of iron-oxidizing bacteria were all negative indicating the leaching tests were conducted under abiotic conditions. The results of the simulated weathering tests permitted the partitioning of the samples into two groups based on positive or negative neutralization potential (NP) values. Determinations were then made to evaluate the degree to which a variety of factors, including temperature, partial pressure of oxygen and water, and crystallography affected pyrite reactivity. Multiple regression analyses showed no statistically significant relationship between degree of reactivity and elemental composition. However, for samples with negative NPs, a simple regression analysis showed a strong linear relationship to exist between the reactivity of the pyrite and the proportion of "unstable" pyrite (framboidal + mossy pitted) found in each extracted pyrite sample. Samples of pyrite with positive NPs, although producing acidity, did so in at least one order of magnitude less than the NP deficient samples, indicating the important role that NP plays in controlling pyrite reactivity. A simple linear regression between cumulative sulfate production and NP for the three samples with positive NPs had a correlation coefficient of 0.99. For the nine samples grouped together, a linear regression model between cumulative sulfate production and NP (both negative and positive) was established between log of sulfate and NP.

Jan 1, 1991

By R. J. Morrell

The Bureau of Mines conducted a series of laboratory experiments to test a cutting technique for hard rock using large-scale drag cutters. Cutting experiments were performed on rocks ranging in compressive strength from 10,000 to 27,000 Ib/in2, using large drag cutters from 3 to 6 in. in width. The tests were conducted on a special test apparatus, called a ripper tester, which made a curvilinear cut across the rock sample while measuring the cutting force acting on the drag cutter. The cutting method that evolved from these experiments is called ripper cutting, and its energy efficiency appears superior to all other large-scale mechanical fragmentation techniques. In addition, the method cre-ated very little dust, and the wear on the bits was negligible. A fragmentation system based on ripper cutting was then devised, and a large-scale test device was fabricated to allow full-scale laboratory testing of the system. The results of these tests will be published in future Bureau reports.

Jan 1, 1986

By K. Shimamoto

This study has been prompted by the anticipated demand for rhenium by the petroleum industry and the concern for an adequate supply of rhenium to meet the demand. The present and projected outlook for rhenium relative to its distribution and occurrences, the recovery factors involved in ore beneficiation, capital and operating costs, changing technology, and the projected uses and market growth of rhenium are presented in this report as part of the Bureau of Mines program to determine the availability of recoverable rhenium in a developing market.

Jan 1, 1973

By N. A. Eilertsen

Among the numerous Low-grade manganese deposits in eastern Aroostook County, Maine, the Dudley deposit near Mapleton in the northern district is one of the few known to contain an appreciable tonnage averaging above 10 percent manganese. The ore body, consisting of stratified manganiferous hematitic shale, is over 5,000 feet long and ranges in width from 30 to 175 feet. The deposit was extensively explored during 1942-44 by the Manganese Ore Co., a subsidiary of M. A. Hanna Co. of Cleveland, Ohio. Data obtained from this work were made available to the State and Federal Geological Surveys for estimating ore reserves. An estimate by the Maine Geological Survey, using a 10-percent manganese cutoff and to a depth of 200 feet, shows 609,000 long tons of manganese metal in material averaging 12.6 percent manganese. By lowering the cutoff limit to 5 percent manganese, the estimate was increased to 919,000 long tons of metallic manga¬nese in material averaging, 10.4 percent manganese,

Jan 1, 1957

By Ernest A. Curth

The Bureau of Mines studied pressure changes in coal pillars by using encapsulated hydraulic pressure cells to measure relative changes in stress developed during mining. The data indicate that (1) abutment stresses were detected when the pillar line is within 42 to 100 feet, (2) vertical pressure increases as coal is mined in the pillars, (3) at first pressure is higher at the edge of the pillar than in the core, but as mining progresses, the higher pressure is measured in the core of the stump, and (4) in the two instances where lateral pressures were measured, they remained lower than the vertical pressures during pillar extraction. The data also indicate that the mean vertical pressure increase, 6P, in a pillar is roughly related to the percent of pillar extracted, A, by the empirical parabolic equation

Jan 1, 1967

By Bernard Lewis

The ignition problem: for a layer of firedamp bordering on a cloud of detonation products is evidently considerably more complicated than in the usual laboratory ignition experiments, in which a well-defined volume of gas is heated and the occurrence of ignition is observed after an induction period. An atmosphere of firedamp exposed to the detonation of a high explosive is subjected to heating by shock-wave compression and thermal conduction and to intermixing at the interface of the firedamp atmosphere and the cloud of deto¬nation products. Although a reliable physical-chemical analysis of the problem is not yet possible, one may nevertheless form a general view of the role of compression waves and the processes of heat transfer and diffusion at the interface. Near the mouth of a shot hole, or near a freely suspended cartridge, the firedamp atmosphere attains very high temperatures by adiabatic compression, and it is certain that such temperatures are sufficient to initiate chemical reaction. The pressure wave pattern is reproducible from one test charge to another if the initial experimental conditions are held constant; on the other hand, experiments on firedamp ignition do not yield a reproducible threshold condition for ignition, but only an ignition probability. Thus, the induction periods are sufficiently long that there is time for the compressed', heated gas layers to undergo random changes that may quench or promote ignition. Therefore, the analysis of the ignition problem hinges primarily on the discovery of the random events that modify the chemical reaction in the activated gas layers.

Jan 1, 1948

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

8. Field Demonstration of the Remote Mine Sealing System in a Coal Mine 8. 1 Selection of Field Test Site Eastern Associated Coal Corporation (EACC) offered its Federal No. 1 coal mine in Grant Town, West Virginia as the site for field testing of the remote sealing system. The choice of Federal No. 1 mine was particularly appropriate as the first attempt at fire control by remote sealing was done in this mine in 1963. EACC provided the men and equipment required for much of the initial preparation. Considerable assistance, advice, and background on coal mining technology was given by Mr. William Laird, Vice President for Research and Development, EACC, and by Mr. Lawrence Jackson, Resident Engineer at the Federal No. 1 mine. District 3 USBM office, the West Virginia Bureau of Mines, the Technical Support Group of the USBM, and Local 4047 of the United Mine Workers of America also cooperated. 8.2 Preparation of Field Test Site 8.2. 1 Underground Site Preparation The underground site chosen for the field testing was in a non-working portion of the mine within a few hundred feet of the main haulage road, as shown in Figure 80. Known as "Seven Switch, " this area was a 20 minute walk or 5 minute "jeep" trip from the man-trip shaft. Ten years having passed since this area was actively worked, considerable effort was required for gob clearing, roof bolting, rock dusting, and rejuvenating the track from the haulage road to the test area. Three primary borehole locations were chosen for the test program. Borehole No. 1 was in a straight passageway

Jan 1, 1973

By Oliver Bowles

From remote antiquity stone has been employed for structural, ornamental, and memorial purposes. It was, and still is, so used because of its availability in innumerable localities and its architectural adaptability, dignity, substantiality, and durability. The principal varieties of stone used are granite, marble, limestone, sandstone, and slate. This report deals with granite. OCCURRENCE AND CHARACTER OF GRANITE Granites usually have been classed as igneous rocks derived from molten masses or magmas, but there is wide evidence that the origin of some granites may be attributed to regional metamorphism of preexisting rocks, rearrangement and recrystallization taking place without a liquid or molten stage. In any event granitization is a slow, deep-seated process.

Jan 1, 1956

By Donald A. Voigt

This publication is intended as a guide for persons responsible for obtaining classifications and approvals Tor explosive compounds, mixtures, or devices from the U.S. Department of Transportation (DOT). It deals with the procedures for obtaining a recommendation for classification of an explosive compound, mixture, or device through the Bureau of Mines. Completion of the procedures detailed in this guide is necessary to obtain a final classification of an explosive compound, mixture, or device and assignment of an "EX" number by DOT, which will allow the producer to offer the explosive for shipment within the United States. This guide also gives procedures for obtaining United Nations (U.N.) classification for shipping outside the United States.

Jan 1, 1990