Search Documents

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds in Russell County , Va . Almost 2 million tons of coal was mined in 1961 ; 75 percent of the coal was cleaned mechanically in preparation plants in the county . The coal of Russell County is ranked as medium- to high- volatile bituminous , contains small amounts of sulfur , and generally requires some cleaning to reduce the ash content to limits acceptable for metallurgical purposes .

Jan 1, 1963

By Hillary W. St. Clair

The purpose of this investigation was to determine the practicability of refining crude aluminum-silicon alloy or aluminum scrap containing silicon and iron by selective dissolution in zinc of the aluminum from the alloy followed by distillation of the zinc from the aluminum.

Jan 1, 1949

By Farrel W. Lytle

An X-ray emission spectrographic method of analysis is presented for determining rare-earth elements in fractions obtained from bastnaesite ore. The method includes determination of yttrium, thorium, lanthanum, and the rare-earth elements in various complex mixtures. The analysis technique is based upon comparing the samples with synthetic standards approximating the composition of the samples. Working curves are plotted on an absolute-intensity basis, with no correction for back-ground. Examples of working curves and the analyses of typical rare-earth concentrates are included. The selection of spectral lines for the various sample matrices is discussed. A special technique is used for samples in which rapid hydration and carbonation occurred. By analyzing synthetic samples of known composition, the accuracy of the method was determined. The average error of analysis was about 3 percent of the amount present in the range from 5 to 100 percent and about 7 percent in the 0.2-to 5-percent range. A maximum of about 40 samples per day may be analyzed for 7 elements each.

Jan 1, 1957

By V. A. Marple, K. L. Rubow, Y. Tao

"A personal diesel exhaust aerosol sampler has been designed and evaluated in both laboratory and field settings. The sampler uses size selective sampling for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particulate matter found in underground coal mines. This design is based on the premise that diesel exhaust particulate matter is predominantly less than 0.8 um while mineral dust is greater than 0.8 gm. Operating at a flow rate of 2 L/min, the sampler consists of a 10 mm Dorr-Oliver respirable dust cyclone followed by an 0.8 gm cutpoint impactor and an afterfilter. Field evaluations consisted of sampling at 6 different locations in these underground coal mines. Measured aerosol concentration less than and greater than 0.8 um have been compared with a well characterized cascade impactor.Techniques must be developed for measuring the mass concentration of diesel exhaust particulate matter found in underground coal mines due to the health concerns associated with worker exposure to diesel exhaust particulate matter. Diesel exhaust particles are in the respirable size range and have been regarded as a potential occupational carcinogen by NIOSH (1988). Furthermore, a 1988 MSHA advisory committee directed MSHA to develop a sampling protocol for assessing worker exposure to diesel exhaust particles.The University of Minnesota and the Bureau of Mines, over the past 4 years have measured the size distribution of diesel exhaust particles and mineral dust, both in the laboratory and underground mines (Cantrell, 1987; Cantrell et al., 1987; Cantrell and Rubow. 1988; Marple et al, 1986; Rubow et al., 1988: and Watts et al., 1989). To date, measurements have been made in nine coal mines. Seven mines utilized diesel-powered equipment at the mine face while two used electric-powered equipment. The results of these field tests indicate that mineral dust and diesel exhaust particles can be differentiated on the basis of particle size. The measured particle size distributions have been found to be bimodal with a saddle point at 0.8 um. This has led to the hypothesis that one method for measuring worker exposure to diesel exhaust particles would be to collect size fractionated particle samples separated at 0.8 um with the diesel particles being less than 0.8 um and the mineral dust particles greater than 0.8 um.Aerosol size distribution measurements, using a micro-orifice uniform deposit impactor (MOUDI), have been conducted in the mine intake air portal, intake entry to the working section, haulageway, and section return entry. The MOUDI is a ten stage cascade impactor with particle cutpoints ranging from 0.1 to 15 um aerodynamic diameter (Marple and Rubow. 1984b; Marple et al., 1989). The sampling flow rate is 30 L/min."

Mar 1, 1992

By M. E. Volin

The Buckeye manganese deposits are in Stanislaus County, Calif., about 33 miles south of Tracy. From 1917 to 1919 the deposits produced 13,370 tons of ore reported to average 46 percent manganese and 14 percent silica. The deposits are confined to two areas of' development, known as the north mine workings and the south mine workings, about 700 feet apart horizontally. Mineralization occurs chiefly as rhodochrosite and psilomelane interbedded in cherts of the Franciscan formation. As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a development project was started November 25, 1940, and completed June 27, 1941. The Federal Geological Survey cooperated by mapping the topography and geology and logging the drill cores. The program included road and. trail building, trenching, underground excavation, diamond drilling, and sampling. The following pages mention the location, brief the history, and note the physical .features of' the district. Mine workings are sketched, the deposit is described, and the plan of the project is noted. The work performed by the Bureau of Mines is explained in the concluding pages with a summary of the drill-hole logs.

Jan 1, 1949

By H. S. Kalman

A table of factors for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, at base conditions of 14.7 psia and 70° F, is presented. The table covers a pressure range from 10 to 10,000 psin in 10-psi increments and a temperature range of 0° to 120° F in 2° increments. The volume of helium is calculated from the observed pressure and temperature of the helium, expressed as a factor from the table, and the known internal volume of the container. The calculation requires a single multiplication. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1968

By S. P. Holt

The Rush & Brown mine has been one of the most consistent small producers of copper ore in the history of Alaskan mining. Approximately 50,000 tons of ore have been shipped to smelters from the property. Production has been made from two distinct and separate ore bodies of dissimilar types. The Shear Vein deposit has been mined to a depth of 500 feet below the surface without a reduction in the size of the ore shoot or the grade of ore. The Magnetite ore body has been partly mined to a depth of 200 feet below the surface. Because of the favorable production record of the Rush & Brown mine, the present need for copper and the fact that the owners were attempting to place the mine in production, it was deemed advisable to investigate this property under the Strategic Minerals Act of 1939 as a possible source of copper.

Jan 1, 1948

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) measurements provide evidence for the formation of Cr(V) intermediates in the enzymatic reduction of Cr(VI) by glutathione reductase (GSSG-R) in the presence of NADPH, indicating an initial single-electron transfer step in the reduction mechanism. Depending on the pH, at least two different Cr(V) species are generated which are relatively long-lived. In addition, we have detected the hydroxyl (·OH) radical formation during the GSSG-R catalyzed reduction of Cr(VI) by spin trapping, employing 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) and a-(4-pyridyl-1-oxide)-N-tert-butylnitrone (4-POBN) as spin traps. Superoxide dismutase (SOD) causes only a minor effect on the ·OH radical and Cr(V) formation, indicating that the ~ - is not significantly involved in the reaction mechanism. Catalase enhances the Cr(V) formation and substantially inhibits the ·OH radical formation, indicating the involvement of hydrogen peroxide (H20 2) in the reaction mechanism. Addition of H20i suppresses Cr(V) and enhances the ·OH radical fonnation. Measurements involving N-ethylmaleimide show that the Cr(V) species, produced enzymatically by the reduction of Cr(VI) by GSSG-R, react with H2O2 to generate ·OH radicals, which might participate in the initiation of Cr(VI) carcinogenicity.INTRODUCTIONC(VI) compounds have been found to exert serious toxic and carcinogenic effects on humans and animals [1-4) and to cause mutations in bacteria and transformation of mammalian cells [5-8). In contrast, most Cr(lll) compounds are relatively nontoxic, noncarcinogenic, and nonmutagenic [9, 10]. Cr(VI) and Cr(lll) oxidation states are different in their metabolic pathways: Cr(VI) ions are rapidly transported across cellular membranes [2, 11-13), while Cr(lll) moieties do not easily penetrate cells and are not oxidized by cellular constituents [3]. Since it is known that the reduction of Cr(Vl) is required for its reaction with DNA [2], the molecular mechanisms for the intracellular Cr(VI) reduction have been the focus of studies during the past decade but the details are still not understood."

Jan 1, 1990

By Nar S. Dala1, Xianglin Shi, Val Vallyathan

"Electron spin resonance (ESRJ and cytotoxicity measurements were made on newly fractured silica to examine specifically the role of the fracture-induced, silicon-based radicals (Si· and SiO·) and silica-generated hydroxyl (·OH) radicals in the mechanism of the cell membrane damage by silica. The concentration of the Si· and SiO · radicals was controlled through decay processes, thermal annealing, and boiling, while that of the ·OH radicals was varied by using catalase, superoxide dismutase, KMnO, Na;iSeO:y ascorbic acid, and metal ions, and monitored via ESR spectroscopy. The dust's cytotoxicity potential was evaluated by measuring the silica-induced hemolysis and also by determining lipid peroxidation (using linoleic acid). From the comparison of hemolysis and ESR results it is deduced that the radicals play little or no role in the silica-induced hemolysis. However, the lipid peroxidation data indicate that the radicals might be involved in the initiation of an oxidative chain reaction leading to the macrophage membrane damage through lipid peroxidation. INTRODUCTIONThe biochemical mechanism of quartz-related pneumoconiosis is still not fully understood. It is believed, nevertheless, that one event of primary importance is the perturbation of cell membranes by the dust particles (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Parazzi et al., 1968; Reiser and Last, 1979; Shi et al., 1989; Summerton et al., 1977). The ensuing cell: membrane damage unleashes certain lytic enzymes resulting in additional cell injury and eventual fibrosis (Nolan et al., 1981; Summerton et al., 1977). Thus considerable effort is currently being made toward the understanding of the processes by which quartz particles disrupt the membrane of a red blood cell (RBC) or a pulmonary alveolar macrophage (PAM). A simple but important method of evaluating the membrane damage potential of a dust is the hemolysis test (Harington et al., 1971). Even though this test is used routinely for screening dusts for their cytotoxicity potential, the biochemical mechanisms underlying the cell lysis by many dusts, including quartz, is still controversial (Kilroe-Smith, 1974; Singh and Rahman, 1987), and this provided us the impetus for the present undertaking."

Jan 1, 1990

In 2005, a total of 4,490 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). Stone mines comprised 30.6% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,039; 45.4%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Of all states, Pennsylvania had the most stone mines (n=379; 8.4%).

Jan 1, 2008

By Seth C. Schaefer

As part of the Bureau of Mines, U.S. Department of the Interior, effort to provide thermodynamic data for the advancement of minerals technology, the Gibbs energy of formation of sphalerite (zinc sulfide) was investigated with a high-temperature galvanic cell employing stabilized zirconia as the electrolyte. In the temperature range 948 to 1,210 K, potential measurements were obtained for the cell Pt, ZnS + ZnO, S02 = 1 atm // Zr02 // Cu20 + Cu, Pt, with the overall cell reaction ZnS(c) + 3 Cu20(c) = ZnO(c) + 6 Cu(c) + S02(g). (1) These results, combined with the best available values of ?Gf° for ZnO, S02, and Cu20 from the literature, give the Gibbs energy of formation of zinc sulfide for the reaction Zn(l,v) + 1/2 S2(g) = ZnS© (2) ?Gf° = -64.223 + 24.02 X 10-3T ± 0.650 kcal/mole (3) (948-1,180 K; standard states - pure liquid zinc and S2 gas at 1 atm), and ?Gf° = -92.720 + 48.17 X 10-3 ± 0.650 kcal/mole (1,180-1,210 K; standard states - pure zinc vapor and S2 gas at 1 atm). A third law analysis yields for the formation reaction Zn(1) + 1/2 S2(g) = ZnS(c), (5) a standard enthalpy of formation as follows: ?Hf298.15 = -63.64 ± 0.700 kcal/mole.

Jan 1, 1978

By N. S. Dalal, X. Shi, V. Vallyathan

"Electron spin resonance (ESR) and cytotoxicity measurements were made on newly fractured silica to examine specifically the role of the fractured-induced, siliconbased radicals (Si· and SiO·), and silica-generated hydroxyl (·OH) radicals in the mechanism of the cell membrane damage by silica. The concentration of the Si· and SiO· radicals was controlled through decay processes, thermal annealing, and boiling, while that of the ·OH radicals was varied by using catalase, superoxide dismutase, KMnO4, Ha2seO3, ascorbic acid, and metal ions, and monitored via ESR spectroscopy. The dust's cytotozicity potential was evaluated by measuring the silica-induced hemolysis and also by determining lipid peroxidation (using linoleic acid). Prom the comparison of hemolysis and ESR results it is deduced that the radicals play little· or no role in the silica-induced hemolysis. However, the lipid peroxidation data indicate that the radicals might be involved in the initiation of an oxidative chain reaction leading to the macrophage membrane damage through lipid peroxidation. INTRODUCTIONThe biochemical mechanism of Quartz-related pneumoconiosis is still not fully understood. It is believed, nevertheless, that one event of primary importance is the perturbation of cell membranes by the dust particles (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Parazzi, et al., 1968; Reiser and Last, 1979; Shi et al., 1989; Summerton et al., 1977). The ensuing cell-membrane damage unleashes certain lytic enzymes resulting in additional cell injury and eventual fibrosis (Nolan et al., 1981; Summerton et al., 1977). Thus considerable effort is currently being made towards the understanding of the processes by which quartz particles disrupt the membrane of a red blood cell (RBC) or a pulmonary alveolar macrophage (PAM). A simple but important method of evaluating the membrane damage potential of a dust is the hemolysis test (Harington et al., 1971). Even though this test is used routinely for screening dusts for their cytotoxicity potential, the biochemical mechanism underlying the cell lysis by many dusts, including quartz, is still controversial (Kilroe-Smith, 1974; Singh and Rahman, 1987), and this provided us the impetus for the present undertaking."

Jan 1, 1989

By R. M. Strong, Lauson Stone

Under the terms of the act establishing the Bureau of Mines, this bureau was authorized to carryon the work of testing and analyzing fuels which had been conducted by the technologic branch of the United States Geological Survey. That work included in its scope an investigation of the availability and uses ofliquid as well as solid fuels, for the original outline of the fuel-testing investigations contemplated, as soon as the funds would be available, a study of the liquid-fuel resources of the country and the making of related researches to determine how these resources could be utilized with greatest efficiency. Owing to the fact that many difficulties were being encountered in the adaptation of the heavier fuel oils for convenient use in internalcombustion engines, it was deemed best to begin the investigation of liquid fuels with tests of gasoline, a fuel in more or less general use. When this investigation began, the extensive introduction, especially by foreign powers, of liquid fuels for small naval craft had awakened much interest. However, the quality of gasoline was reported to vary materially in different countries and the quantity available was said to be rapidly decreasing, with the probability of a prohibitive increase in price. At the same time the claim was made that denatured alcohol, of fairly uniform quality, could be procured in all parts of the world, that unlimited quantities could be readily produced at a low cost, and that this fuel could be used much more efficiently than gasoline in internal-combustion engines. Such statements naturally led to a widespread belief that the time was near at hand when denatured alcohol would entirely displace gasoline as engine fuel. Therefore, the first investigations of the liquid mineral fuels logically embraced a careful series of comparative tests of gasoline and denatured alcohol in engines. A series of over 2,000 such tests was conducted at the Government fuel-testing plants at St. Louis, Mo., and Norfolk, Va., details of which are given in the following pages. The report is published by the Bureau of Mines because of the transfer of the fuel-testing investigations to this bureau.

Jan 1, 1912

By Albert W. Deurbrouck

This report describes preparation characteristics of significant coalbeds in Tazewell County , Va . In 1961 Tazewell County produced 933,110 tons of clean coal from six coalbeds ; the Lower Banner , Raven , Jawbone , Upper Seaboard , and Pocahontas No. 3 and No. 5. Samples from all of these beds , except the Lower Banner , were included in this study plus a sample from the Pocahontas No. 4 bed . Of the samples collected , only one would require upgrading to be of metallurgical quality . The coals ranged in rank from high- volatile -A to low- volatile bituminous .

Jan 1, 1963

By W. R. K. Wu

Studies are reported on the structure of coal and coke with the graphical , statistical densimetric method based on the relation between the molecular volume per carbon atom ( M / C ) and the atomic hydrogen - carbon ratio ( H / C ) . Previous work , mostly from chemical and physical investigations , is critically reviewed . Difficulties in evaluating the ring increment are demonstrated for coal and coke for the statistical densimetric method based on the additivity of atomic volumes of constituent elements . A new diagram is presented for the graphical method . Methods are introduced for correcting M /C and H/C for the presence of minor constituents in coal and coke . With the graphical method , the fractions of aromatic carbon atoms in the total carbon atoms are estimated for a coal , a resin , and 5 petrographic components ; the types of condensed structure in the fundamental units of molecules are discussed for these substances , 28 coals , and 6 " average " cokes at 500 ° to 1,000 ° C. It is also shown that the number of rings in the fundamental units of coal generally increases with increasing rank and that of coke , with increasing carbonization temperature .

Jul 1, 1960

By F. G. Schwartz

The Bureau of Mines developed a rapid and precise method for predicting storage stability of motor gasolines. This method resulted from the investigation of many analytical techniques as well as a study of fuel composition and fuel component gum-forming mechanisms. The first section of this bulletin discusses the development of the prediction test through its several phases, including revision of the standard 110° F storage test; attempts to develop a modification of the ASTM D525 induction bomb test; and the ultimate abandonment of this procedure with the adoption of the 16-hour oven test that was both precise and rapid. The second section comprises a discussion of further studies of fuel com- position, including the reactivity of certain sulfur compounds and hydrocarbons to form gum. The compositions of various gums and inorganic deposits are reported in terms of elemental analysis and spectroscopic examinations. The reactions of tetraethyllead with selected hydrocarbons are also reported.

Jan 1, 1972

By F. E. Joyce, Charles Prasky

This report describes the response to high- temperature sulfatization of a variety of manganese minerals and companion compounds which may occur either as a principal component or as a gangue material in low- grade manganese deposits . Fourteen manganese samples representing oxide , carbonate , and silicate minerals as well as seven compounds which might occur as gangue with manganese minerals were tested batchwise in a bench- scale apparatus under conditions which would be favorable for the sulfatization of manganese . The manganese minerals substantiated thermodynamic predictions and responded to sulfatization but to varying degrees . The gangue materials , MgO , MgCO,, CaO , and CaCO3 , were sulfatized readily in contrast to the iron oxides and the aluminacontaining material which were not .

Jan 1, 1964

By William H. King

Preliminary examination of the Virgin River manganese deposit was made by C. H. Johnson, Bureau of Mines engineer, in March 1941. During, April and May 8 trenches were dug, a 48-foot inclined shaft was sunk, and 719 linear feet of channel samples were cut. McKelvey and Wiese, of the Federal Geological Survey, completed mapping the deposit, including the entire area of overlying formations comprising the point of land between the outcrop and Lake Mead. The geologic maps, maps, and ore estimates resulting from these examinations formed the basis for a preliminary report by C. H. Johnson, who recommended further exploration by diamond drilling.

Jan 1, 1949

By Thomas A. Jones

An impure variety of barite, which lends itself well to the manufacture of heavy drilling mud for oil wells, is widely distributed throughout the Ouachita Mountains in Arkansas. The ore mined in the area and used for drilling muds usually contains an average of 67 percent barium sulfate, although ores as low as 50 percent BaSO4 are occasionally used. Due to the increased demand for barite for drilling caused by the intense search for hew oil occurrences during the years 1945 and 1946, the Federal Bureau of Mines began an investigation of barite deposits in the Ouachita? Mountains in October 1946. In all, 10 barite deposits were examined, trenched, sampled, and studied during the investigation, which was terminated in May 1947.

Jan 1, 1948

By D. A. Paice

Direct current electrical systems are used in most coal mines primarily to power the main haulage trains and secondarily to feed other equipment and passageway lighting. Electrical power is supplied from rotary machines or static rectifier equipment and is distributed through the mine by open trolley wires and feeder cables. The rails of the haulageway are used as a current return path. This exposed power distribution system is very vulnerable to conditions which lead to undesired leakage currents and short circuits and, consequently, the possibility of fires or other hazards to personnel. Present techniques and equipment have been utilized in so far as practical to improve the safety of the dc electrical system; however, there still appears a need for further improvement. Because of this need, this program was sponsored by the Bureau of Mines to investigate two specific technical areas related to improvement of dc electrical system safety. One area included the determination of the characteristics of mine electrical systems and their protection requirements and the verification of the adequacy of available protective devices for mine service. Despite the widespread application of industrial protective equipment in mines, there was little detailed technical information available related specifically to the performance of this equipment in service. Our task was not only to develop useful information regarding mine system protection, but also to define and verify the adequacy of the protective devices available. The second area of investigation called for development of a practical technique for detecting low level electrical fault or leakage currents. Conventional protective devices

Jan 1, 2012