Search Documents

By Edward C. Peterson

Recent studies indicate that the United States halt substantial reserves of ilmenite, one of the major titanium minerals. However, the studies showed that sources of rutile, another important source of titanium are limited. This paper summarizes and evaluates results and conclusions reached by the various investigations initiated by the Bureau of Mines and others pertaining to the titanium mineral resources of the Nation. Domestic occurrences of ilmenite that are economically exploitable by present-day beneficiation methods are found in Florida, New Jersey, New York, South Carolina, and Virginia. These deposits are estimated to contain 50.3 million tons of titanium dioxide (TiO2). Occurrences of ilmenite that cannot be processed economically under present technological conditions are found in California, Colorado, Minnesota, Montana, Oklahoma, Oregon, Rhode Island, and Wyoming. These reserves amount to 51.1 million tons of TiO2. Reserves of rutile found in the United States are estimated to be 1.8 to 2.1 million tons of TiO2. Other than occurrences in Florida and South Carolina, rutile is found either in small scattered bodies or in deposits where the mineral cannot be recovered economically by present beneficiation methods.

Jan 1, 1966

By E. G. King

Thermodynamic calculations involving the oxides of tungsten and molybdenum have been hampered by lack of accurate entropies and high temperature heat contents. This paper presents work by the Federal Bureau of Mines on new low-temperature heat-capacity data leading to the evaluation of the 298.15° K. entropies of tungsten dioxide and tungsten trioxide, as well as high-temperature heat contents (above 298.15° K.) of molybdenum dioxide, molybdenum tri-oxide, tungsten dioxide, and tungsten trioxide. Included are heats of fusion of the two trioxides. The heats of formation at 298.15° K. of these four oxides are tabulated as measured by Mah4 5/ of this laboratory. Included also are the 298.15° K. entropy of Mo02 measured by Kin 6/ of this laboratory, and that for Mo03 according to Kelley and King.7/ These basic data provide a consistent compilation from which to perform accurate thermodynamic calculations involving these compounds. No previous low-temperature- heat-capacity measurements have been reported for tungsten dioxide. Seltz, Dunkerley, and DeWitt8/ measured the low-temperature heat capacity of tungsten trioxide. The only previously-reported high-temperature heat-content measurements for any of the oxides were conducted by Cosgrove and Snyder,9/ who measured molybdenum trioxide to 1,300° K.

Jan 1, 1960

By A. J. Kraemer

This paper is the second and concluding report of the results of the twenty-fourth semiannual survey made by the Bureau of Mines of motor gasoline marketed in the United states. The first report on this 1931 survey gave the results of the examination of the gasoline samples in accordance with the new Federal specification for United States Government Motor Gasoline. The present paper reports results of the examination of the gasolines for color, doctor test gravity, end point, per cent recovered copper-dish gum, and steam-oven gum. The retail price and the tax at the time each sample was taken are also reported.

Jan 1, 1932

By Kim B. Shedd

The Bureau of Mines measured fiber dimensions on crocidolites (riebeckite-asbestos and magnesioriebeckite-asbestos) from the world's four crocidolite mining regions. The objective of the study was to determine whether there are measurable morphological differences between crocidolite fibers that correlate with the high reported incidence of mesothelioma in miners and mill employees in the Cape Province of South Africa and Western Australia, as compared with little or no reported incidence of this cancer in the Transvaal Province of South Africa or Bolivia. Fiber dimensions measured with the scanning transmission elec-tron microscope showed that crocidolites from Western Australia and the Cape Province have more thin fibers than crocidolites from Bolivia and the Transvaal Province.

Jan 1, 1985

By R. Y. Williams

The investigative work described in this report was undertaken by the Bureau of Mines under a cooperative agreement with the department of mining engineering of the University of Illinois and the Illinois State Geological Survey." The purpose of this agreement was to provide for a comprehensive investigation of coal-mining conditions in the State, with especial reference to the possibility of lessening waste in the mining and preparation of coal and of reducing the dangers to which miners are exposed. The Bureau of Mines paid particular attention to those phases of the investigation that were of general interest from their bearing on safety and efficiency in the coal-mining industry as a whole. Thus, it studied the occurrence of gas (methane) in the mines of the southern part of the State," tested the inflammability of the coal dust from many mines, examined the efficiency of the control of ventilating currents, and investigated the factors affecting the humidity of mine air with respect to their bearing on the occurrence of mine explosions. Following the establishment of the fact that under certain conditions dry bituminous coal dust is inflammable, there arose the problem of finding efficient methods of preventing or limiting coal-dust explosions. Experiments in the gas-and-dust gallery at the Pittsburgh testing station of the Bureau of Mines verified the fact that certain dusts that explode violently when dry are rendered inert by proper humidi- .fication of the atmosphere within the gallery, and the importance of humidity as a factor in limiting the inflammability of coal dust in a mine is demonstrated by the fact that there has never been in Illinois a dust explosion during the summer months, whereas the records show a number of dust explosions during cold weather. It is easy to see that the warm moisture-laden air that enters a mine in the summer must deposit moisture on cooling, whereas the cold and relatively dry air that enters in winter must take up moisture as it becomes heated in traveling through the mine.

Jan 1, 1914

By William W. Adams

A general increase in employment prevailed in the stone-quarrying industry of the United States during 1941 compared with 1940. Likewise, more accidents occurred to men working in and about the quarries, with the result that the accident-frequency rate for the industry as a whole was higher in 1941 than in the previous year. Reports from operating companies to the Bureau of Mines, covering open and underground quarries, as well as rock-crushing and rock-dressing plants, cement mills, and limekilns at or near the quarries, showed a total of 86,123 men employed and a total of more than 22 million man-days of labor performed during 1941. The total working time of the industry averaged 260 days per man. Measured in man-hours, the volume of work equaled 173 million, an average of 2,011 man-hours per employee.

Jan 1, 1943

By John Ward Smith

The Bureau of Mines drilled Wyoming Corehole No. 1 in Sweetwater County, Wyo., to sample Green River Formation oil shale. Core obtained was assayed for oil yield to determine richness and stratigraphic distribution of oil shale in the deposit. Oil shale in place at Wyoming No. 1 site represents over 200 million barrels of oil per square mile. Additional data useful in evaluating the deposit, including generalized stratigraphy and mineralogy, detailed lithologic descriptions of the core, rock specific gravity, and bore-hole logs, are presented with the oil-yield data. The sampled Wyoming oil shale resembles Mahogany-zone oil shale in rock properties and gross mineralogy. A statistically derived equation relating shale density to oil yield for the Wyoming deposit compares with a similar relationship valid for the better known Mahogany-zone oil shales in Colorado and Utah. A density log from Wyoming Corehole No. 1 is calibrated for direct oil-yield logging. The alternating rich and lean beds of shale at this site may permit creating the permeability necessary for direct production of shale oil from the shale in place.

Jan 1, 1968

By John R. McWilliams

This is one of a series of reports being published by the Bureau of Mines on mining methods and costs at various mines throughout the United States. Including the Holden mine in this series is particularly appropriate at this time. The mine was operated on a low-cost, large-scale production basis to compensate for low-grade ore. Even with the best conditions and the most efficient methods, the margin of profit was small. Under the present situation of rising costs and lowering metal prices, the profit margin vanished. On June 28, 1957, the mine operations ceased; therefore, this report can review the entire life span of the mine.

Jan 1, 1958

By Thomas M. Nasiatka

This report briefly describes the present state of the art and the technological highlights of tunneling from its inception to the present. The discussion is concerned primarily with tunnels driven through relatively competent rock for mine development and various civil purposes. In addition to pinpointing the major technological breakthroughs in tunneling, this report indicates their general effect on the speed of tunneling. The tunneling speeds are based upon data from approximately 80 tunnels listed in the appendix. These data include length; cross section shape and dimension; type of rock; tunneling method; method of breaking, loading, and transporting the rock; average linear progress rate; and cost in values during the period of construction. Most of the tunnels described have diameters of 15 to 30 feet.

Jan 1, 1968

By R. A. Friedel, J. L. Shultz, A. G. Sharkey

The purpose of this investigation was to study the primary materials associated with the coal structure . Mass spectrometric techniques can be useful in studying the chemical structure of coal and various high- molecularweight materials derived from coal . Investigations of pyrolysis products and extracts of coal , and also whole coal , showed : 1. Aromatic hydrocarbons obtained by the vacuum pyrolysis of coal below 300 ° C possibly were sorbed material rather than decomposition products . 2 . 2 . Thirteen structural types having molecular weights from 78 to 400 were identified in pyridine extracts constituting one - quarter or more of the coal by weight . 3. Material extracted at room temperature with a methanol - benzene solvent and a vacuum pyrolysis condensate obtained at 450 ° C contain similar components . The extract and the condensate have approximately the same average molecular weights ( 200-300 ) . 4. Material extracted from coal at room temperature is altered even by mild thermal treatment . 5. Changes in various alkyl series occurring in thermally treated coal extracts can be followed quantitatively . 6. Similarities in the spectra of coal and graphite were indicated in an investigation using a mass spectrometer equipped with a spark source . Determinations on a coal - ash sample by this technique showed good agreement with data obtained by emission spectroscopy .

Jan 1, 1963

By D. E. Shanks

As part of its goal to help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is investigating a fused-salt electrolytic procedure for producing zinc metal. A previous report described preliminary, small-scale work on the fused-salt electrolysis of ZnC12. The present report covers a more detailed investigation of the properties of ZnC12-alkali metal chloride electrolyte systems in relation to the production of zinc metal and also discusses electrolysis in largescale, internally heated cells. The effect of composition on bath stability, current efficiency, cell voltage, and liquidus temperature was determined for the ZnCla-NaC1-KC1, ZnC12-NaC1-LiC1, and ZnC12-KC1-LiC1 electrolyte systems. An electrolyte com-posed of 38 mole-pct ZnC12, 31 mole-pct NaC1, and 31 mole-pct KC1 gave the best overall results. Sludge (ZnO) formation in the ZnC12-NaC1-KC1, ZnC12-KC1-LiC1, and ZnC12-KC1 systems was investigated during prolonged electrolysis. The ZnC12-KC1-NaC1 electrolyte showed the least sludge formation. A 1,500-amp cell was operated using the ZnC12-NaC1-KC1 electrolyte at 500° C. Zinc metal was produced at the rate of 4.0 lb/hr with a current efficiency of 95 pct.

Jan 1, 1979

By William C. McBee

Specialized sulfur concretes were developed by the Federal Bureau of Mines as a result of research for the beneficial utilization of sulfur in construction materials. Materials were developed for use in acid and salt corrosive environments where portland cement concrete has been found to deteriorate. Because the mineral aggregates also come into contact with the corrosive media, concretes were developed utilizing both limestone and quartz aggregates. The sulfur binder used with both aggregates was modified by reaction with 5 pct dicyclopentadiene to improve product durability. Sulfur quartz aggregate concrete was found to have moderately high strength characteristics (6,000 psi compressive) and was extremely resistant to chemical attack by both acid and salt solutions. Sulfur limestone aggregate concrete exhibited very high strength characteristics (9,000 psi compressive) and was extremely resistant to chemical attack of salt solutions. Both types of concretes maintained their strength and integrity after long-term testing in acid and salt solutions and exhibited considerable resistance to damage by the action of freezing and thawing. Potential uses include leach tanks, electrolytic cells, thickeners, bridge decking, industrial flooring, pipe, and tile.

Jan 1, 1979

By K. K. Kelley

Synthetic fluorphlogopite mica (KMg3AlSi3010F2) is a relatively new product developed at the Norris (Tenn.) Station of the Bureau of Mines, Thermodynamic data have applications both in the production and use of this product, and the work described in this paper was undertaken to fill the need for such data. Measurements were made of the heat of formation at 298° K., the heat capacity between 50° and 298° K., the entropy at 298° K., and the heat-content and entropy increments between 298° K. and a maximum of 1,804° K. These basic data are combined to obtain heats and free energies of formation of the mica from the elements and from molecular constituents at temperatures ranging from 298° to 1,800° K. Minimum heat requirements to form melted mica from commonly used ingredients were calculated.

Jan 1, 1959

By H. R. Babitzke, H. Kato, R. E. Siemens, G. Asai

The purpose of this investigation was to develop a wide variety of columbium and tantalum alloys and to determine their suitability for use at elevated temperatures . Sixty - nine columbium and tantalum alloys were investigated . For this study , columbium was alloyed with two or more of the following : nium, tungsten , vanadium , titanium, and zirconium . Tantalum was alloyed with vanadium or hafnium, or hafnium and carbon . The fabricability was determined by an arbitrary procedure . Hardness measurements , elevated - temperature tensile properties , and oxidation- resistance studies were made . Of the alloys studied , Cb - 15 Hf - 5W, Cb - 15Hf - 5W- 10Ti , Cb - 15Hf - 10W- 10Ti , Cb - 10V - 5W, Ta - 30V , and Ta - 20 to 33Hf exhibited excellent high - temperature properties . These alloys were not only easy to fabricate , but they also had good oxidation resistance and excellent high- temperature strength .

Jan 1, 1964

By A. J. Kraemer

This paper is the second and concluding report of the results of the twenty-fourth semiannual survey made by the Bureau of Mines of motor gasoline marketed in the United States. The first report7 on this 1931 survey gave the results of the examination of the gasoline samples in accordance with the new Federal specification for United States Government Motor Gasoline.8 The present paper reports results of the examination of the gasolines for color, doctor test, gravity, end point, per cent recovered, copper-dish gum, and steam-oven gum. The retail price and the tax at the time each sample was taken are also reported.

Jan 1, 1932

By Robert M. Strong

The following report is a summary of the commercial results which 'Were obtained from 2,000 tests conducted by the technologic branch of the United States Geological Survey at St. Louis, Mo., and Norfolk, Va., in 1907 and 1908, under the technical supervision of R. H. Fernald, engineer in charge of the producer-gas section. The tests dealt primarily with gasoline, forming part of the investigation of mineral fuels provided for by acts of Congress. To determine the relative economy and efficiency of gasoline it was compared with denatured alcohol. The tests, many of which were undertaken in connection with work for the Navy Department, supplemented, to a certain extent, the work of previous investigations, but only so far as was necessary to emphasize some of the more important points and to lead up to the defining of conditions required for the economical use of gasoline and alcohol. In order to determine and eliminate the affecting engine conditions as far as possible, the investigation was commenced by making comparative gasoline and alcohol tests on the same engines. These tests were repeated on other engines of approxiElately the same size and speed, having different degrees of comFression, different methods of governing, and different carburetors. The final report will include much material that may be of use in engine design, but that side of the investigation was not pursued any further than was necessary to obtain the best possible results, for alcohol and for gasoline with the engines at hand, and to prove that the minimum fu·el-consumption rate for each could be obtained in approximately the same manner. The effects of engine and of operating conditions both have a bearing on the commercial deductions but will be discussed only in a general way at this time.

Jan 1, 1911

By Carl Belser

This report is the first of a series dealing with the oil-shale reserves of the Green River formation in the Rocky Mountain Region. The known oil-shale reserves of northwestern Colorado at present considered to have economic value apparently are confined to the Piceanco Creek basin between the Colorado and White Rivers. The number of sampled sections is small, but there can be little doubt that the Piceance Creek basin is a potential source of enormous quantities of liquid fuels and the related byproducts obtained from oil-shale processing. The partly blocked and inferred oil-shale reserves of 25-gallon-a-ton shale are estimated to have an oil yield of 125 billion barrels and the reserves of 15-gallon-a-ton shale are estimated to have an oil yield of 494 billion barrels. The number of available sampled sections is inadequate for making firm estimates.

Jan 1, 1951

By L. C. IlsLey, J. W. Paul, E. J. Gleim

Flame safety lamps have been used in gaseous mines since the Davy lamp was introduced, more than 100 years ago. During the last decade the flame safety lamp has been rapidly replaced by the electric lamp as a device for illuminating the miner's working place; in the United States the electric cap lamp has been widely adopted. For example, in 1911 approximately 45,000 flame lamps and no electric lamps were being used in the Pennsylvania bituminous mines, which were then producing 35 per cent of all the soft coal mined in this country; by 1918 the flame lamps had decreased to 17,000, whereas electric lamps-mostly of one maketotaled nearly 48,000. In Great Britain during the same years the total of 723,934 flame lamps decreased to 590,185 and the electric lamps gained rapidly from 4,298 to 156,521. No later reliable figures are at hand. However, before the flame lamp becomes obsolete, it is fitting that the Bureau of Mines compile a permanent record of a device which has served the mining industry for more than three generations, and not only made possible the development of entire districts that otherwise could not have been worked but undoubtedly saved the lives of thousands of underground workers. Flame safety lamps are capable of doing more than the name indicates. First, under normal conditions, they can be used in a mine atmosphere that contains an explosive mixture of gas and air without great danger of exploding such a mixture, though such use of a flame lamp should not be permitted. Second, to an experienced man they indicate percentages of gas much lower than the explosive limit, and thus can be used to indicate to workers the approach of an unsafe condition in the mine atmosphere. Third, flame lamps will not burn in an atmosphere greatly deficient in oxygen, and they therefore warn the users of such deficiency in time to withdraw to a place of safety. Flame safety lamps are still used rather widely in the United States for general illumination and to a still greater extent for detecting gas. Many coal-producing States require fire bosses to use these lamps in gaseous mines, and the regulations of several States specify that a gIven number of such lamps be kept available for emergency service.

Jan 1, 1924

By W. K. Tolley

This report presents data collected during research by the Bureau of Mines on corrosion of grinding media. Corrosion rates of eight alloys commonly used in grinding media were tested in synthetic mill water using an ultrasonic grinding device especially designed for this work. Electro-chemical measurements showed variations in corrosion rates for these alloys between 9.8 mpy for medium-carbon steels and 0.14 mpy for high chromium white irons. Bureau data are discussed along with data from the literature to indicate that corrosion causes less than 10 pct of the wear of grinding media in commercial grinding mills. A comparison of corrosion rates for various types of grinding media shows that alloying elements and electrochemically active inclusions in steel affect the corrosion behavior of the media.

Jan 1, 1984

By W. L. Crentz

In Fayette County, the Pittsburgh bed has been the major source of production for almost two centuries. Although historical documentation is not available, there is evidence, that the Pittsburgh bed may have been discovered in Fayette County near Mt. Braddock, Pa., as early as 1753. The earliest known reference to coal in western Pennsylvania was recorded in 1758 by a Quaker trader, James .Kenny, who reported having seen coal in Fayette County. The production of coke from Pittsburgh coal was begun in 1841, when two 10-foot beehive ovens were erected in the Connellsville region to make coke .for shipment by river to the market. The Connellsville, region extends from Latrobe, Pa., in Westmoreland County to South of Uniontown, in Fayette County. Connellsville coke was used with great success in the Clinton furnace in 1859.

Jan 1, 1951