Search Documents

By Robert Lundquist

REAM is a unique method of rock breaking using high energy projectile impact. This report-describes the most recent in a series of tests demonstrating mining applications for the REAM method. In an underground limestone mine at Greer, West Virginia, REAM was used to drive a short tunnel and drill a large diameter borehole. Along with breakage data from these tests the goal of the program was to examine environmental problems which might result from the use of cannons under-ground. A total of 103 shots was used to advance a 14-l/2-feet high by 10-feet-wide face a distance of 5-1/2 feet. It is estimated that the 9.3-pound-concrete projectiles launched at 5000 feet per second will break an average of 0.78 tons of limestone or 67 percent of the 1.125 tons of granodiorite broken in previous tests. The 9-inch-diameter borehole was drilled horizontally by repeated axial impact for 7 feet, 2-1/2 inches by 21 shots giving an average of 4.12 inches per shot. Scaling this result to compressible impact energy yields an estimated 5.8 inches per shot for a 12.8-inch-diameter hole compared to 8 inches per ~hot for a 16-inch-diameter hole in granodiorite. Noise measurements indicate that a silenced cannon can be used within a few hundred feet of mine personnel in a room and pillar mine within the legal limit of 140 dB impulse without additional protection. Some fume measurements were made with satisfactory results, even though the military propellants used produce much greater quantities of toxic fumes than the liquid propellant proposed for the future.

Jan 1, 1976

By R. L. Handy

The objective of this research was to devise and test an apparatus to rapidly evaluate the cohesive and frictional strength of coal in situ, in order to increase the safety and percentage of coal recovery from underground coal mines. During the first year device was designed utilizing the bore-hole shear test principle from soil shear strength testing: Two opposing corrugated plates are forced outward to exert a controlled contact pressure against the sides of a previously bared hole, and then the plates are very slowly pulled along the axis of the hole to cause shearing of coal in contact with the plates. Results with the device are expressed in terms of a friction angle[_] and a cohesion c. The [ ] angles obtained from an Iowa coal arc in close agreement with and fall between results from triaxial and direct shear laboratory tests on the same coal. The measured cohesion was found to be much less than from the comparable laboratory tests. It may be increased by pre-stressing and other techniques to embed the shear plate teeth for the first shear test point.

Jan 1, 1973

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-million-standard-cubic-foot-per-day, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 million tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the terms of the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment varies: $65,137,900 for the 4.8-million-ton-per-year (MM tpy) mine in the Eastern province, $78,514,600 for the 6.72-MM-tpy mine in the Interior province, and $42,050,100 for the 9.2-MM-tpy mine in the Northern Great Plains province. Total capital investments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $86,969,900, $109,378,500, and $78,543,500, respectively. Corresponding selling prices for the coal, per ton, are $6.94, $6.03, and $3.39, assuming a 15-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1976

By J. P. Hansen

Wustite beds were reduced with carbon monoxide and mixtures of hydrogen and nitrogen in the temperature range 900° to 1,300° C to determine the effect of temperature, gas flow, and surface area on the rate of reduction to iron. The composition of the gas stream as it passed through the wustite bed was continuously measured with infrared absorption cells and heated-wire methods. The change in composition was used to calculate the reaction rates. Arrhenius plots of the data give heats of activation of 34 kcal for particles using CO, 27 kcal for particles using H2, 24 kcal for pellets using C8, and 6 kcal for pellets using H2. The velocity of reduction is dependent on the area of reacting interface and the driving potential of the gas (reducing gas concentration minus equilibrium concentration) as well as the exponential temperature effect. The reaction rate was independent of the gas velocity over the range of conditions studied.

Jan 1, 1965

By C. H. Fisher

[Many methods of analyzing tar oils for their tar acid and base content have bun employed in connection with both academic and. industrial investigations. Most of these analytical procedures are based on the diminution in volume caused by extraction with alkali and mineral acids (contraction method), although other methods haves been employed.4/ In many instances the adoption of an analytical method was not preceded by adequate study, and, as a consequence, the literature, on this subject is conspicuous for its contradictory claims and recommendations. It has bin shown in the, case of certain synthetic solutions5/ that large errors may result if the analysis is carried out by simple extraction with alkali and mineral acids.]

Jan 1, 1936

By N. A. C. Smith, D. D. Stark

"Sulphur is apparently a normal Constituent of crude petroleum, but in most crudes is present in percentages of less than one-half of one per cent. Some crudes, however, contain more, and occurrences have been reported of heavy asphaltic oils with as much as five per cent of sulphur.Occurrences of Sulpher-bearing CrudesIn North America, the fields rest of the Mississippi River are almost entirely free from sulphur oils, the time oil from Northern Ohio and Indiana, and the Potrolia crude in Ontario, being practically the only ones which contain sulohur in amounts over 0.5. per cent. In the Mid-Continent district the production of high sulphur crude in general is small and unim¬portant. The two main excentions are the Healdton field in Oklahoma and the El Dorado field in Arkansas, both of which produce oils with considerable sulphur content. In the Wyoming field, one sand, the Ember Sandstone, pro¬duces a crude of high sulphur content, and it is probable that this crude rill be of considerable importance as production increases. At present, however, very little crude is produced from this formation. In the Gulf Coast conditions are irregular, some crudes being low in sulphur and others comparatively high. The same is largely true of California. The crudes of Mexico contain notable amounts of sulphur, and as they have been of great commercial importance in this country, a typical sample of light Mexican crude was selected for the present study. It is probable that the results obtained poly also (but to a lesser degree) to other sulphur-bearing oils. An analysis of this crude will be found in Table 3, also analyses of other typical sulphur-bearing crudes from different sections of the United States."

Mar 1, 1924

By Phillip Allender, Wolf Karo, Knox Van Dyke, Lixin Wu, Ali Ardekani, Jorge Garcia, Jaime Gutierrez

"We report that two different micropolystyrene round beads linked to either luminol or lucigenin have been developed. The 1-µ.m-diameter beads arc useful reagents that allow one to perform chemiluminescent (light producing) phagoeytic reactions without opsonization. It is known that luminol reacts with peroxidases (e.g., myeloperoxidase) while lucigenin reacts mainly with superoxide anion. Luminol and lucigenin beads produce cellular chemiluminescence (CL) with neutrophils, macrophages, monocytes, and differentiated human promyelocytic leukemic cells (HL60). When myeloperoxidase (MPO) is present luminol beads evoke higher CL from neutrophils, but when little or no MPO is present, lucigenin beads produce higher amounts of light. Lucigenin beads appear to be active inside these cells where unbound lucigenin does not enter freely.INTRODUCTIONA variety of cells, e.g., neutrophils (Ns) and macrophages (Ms), can engulf foreign particles (1). This engulfing or phagocytic activity is used by the body to kill bacteria and to eliminate foreign particles such as respirable dusts, e.g., coal, silica, or cotton. The neutrophil engulfs or phagocytizes bacteria which are coated with plasma antibodies and/or complement proteins (Fig. 1). The coating or opsonization allows the neutrophil to recognize foreign substances. Usually the absence of opsonization prevents the cell's recognition of a foreign particle and the particle is not phagocytized. Macrophages, particularly the alveolar Oung) cells, do not require opsonization for phagocytosis. Ms should not be selective toward individual dusts because they serve a major role in eliminating a variety of these.Particle size can also be a factor. Usually a particle with a diameter of 0.5-5 µ.m is considered in the respirable range. Larger particles are trapped before they reach the alveoli Oung spaces where oxygen exchange with blood occurs), ·and smaller particles do not generally settle, and are not engulfed by macrophages (2). Tabato and Ikada (3) found that maximal phagocytosis of microspheres takes place when their diameter is in the range of 1.0 to 2.0 µ.m. In addition, they found that beads with hydrophobic surfaces were more readily phagocytized than hydrophilic surfaces."

Jan 1, 1990

By J. Mutmansky, C. Lee

"The size distribution of coal mine dust is one of its most important characteristics because the particle size is known to govern the region of deposition of dust within the human respiratory tract. In addition, dust characteristics, particle settling rate, transportability of the dust and the efficiency of dust control measures are all affected by the particle size. As a result, particle size distribution of the airborne dust in a coal mine is a fundamental property that impacts on the health of underground workers.This paper deals with some basic findings on the size distribution of cool mine dust based upon the results of data collection in six underground coal mines using continuous miners. All airborne dust sampling was performed on development sections using eight stage cascade impactors and permissible 2. O l / min pumps. Samplers locations were fixed in the sections with respect to the continuous miner and roofbolter or with respect to the intake and return airways • Sampling times varied from 45 minutes to 6 hours , depending upon the dust concentration. The first topic of analysis was the test to determine whether the commonly used lognonnal distribution is valid when applied to airborne coal mine dust. Secondly, the conventional method of representing the· distribution using two parameters, the geometric mean and the geometric standard deviation, is questioned. Since almost all size data were found to show some degree of bimodality, the two parameter lognonnal distribution may not represent the total airborne coal mine dust size , quite adequately. Bimodal lognonnal distribution was tested to be a good approximation in the case with two modes in the size distribution.The final topic discussed in this paper is the 'locational variation of the airborne dust size distributions within the continuous mining section. The size distributions varied considerably at the different sampling locations with the continuous miner and roofbolter producing the coarser distributions. Fine size modes in the range of 2 to 4µ m including mostly respirable dust particles were present in almost all samples • Second dust generating sources such as the shuttle car movement were found to be major causes of high respirable dust concentrations in some cases ."

Jan 1, 1988

By William Catron

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and cuts in the various reining districts of the United States. The mining methods described are those used in the mines of the Cananea Consolidated Copper Co., a Mexico corporation whose holding company in the United States is the Greene Cananea Copper Co. The mines are at Cananea, Sonora, Mexico, 25 miles directly south of the international boundary, approximately in 31° nor to latitude and 110 to 130° west longitude. Cananea is connected with the boundary towns of Naco and Nogales, Ariz., by a standard-gage railroad.

Jan 1, 1930

By Daryl R. Tweeton

The Bureau of Mines is investigating possible applications of geophysics to monitor leachate during in situ mining. Tomographic reconstruc-tion of seismic or electromagnetic crosshole data appears applicable. The tomographic program BOMTOM (Bureau of Mines tomography) was written and then used to investigate reconstructions with synthetic travel time data. The calculations confirmed that without constraints, crosshole data do not provide unique solutions. The solution is not determined solely by the data, but is also influenced by the velocity guesses starting the iterative solution procedure. The effectiveness of constraints in combatting nonuniqueness was examined. The requirement that the velocity not vary laterally at the top and bottom of the pixel grid was effective. This constraint is realistic when the top and bottom of the grid represent dry and saturated re-gions, respectively. Limiting the maximum velocity improved reconstructions, but may not be applicable in practice. BOMTOM uses the simultaneous iterative reconstruction technique (SIRT) with straight ray paths. The program is efficient in use of memory, and can be run on a personal computer. A source code in FORTRAN is listed. A source code in BASICA and compiled executable codes in both languages are available from the Bureau's Twin Cities (MN) Research Center.

Jan 1, 1985

By Guy B. Taylor, Horace C. Porter, E. C. White

When the Federal investigation of coal - dust explosions in mines was begun in 1908 , following a series of mine explosion disasters in 1907 , mining men generally questioned whether coal dust in air is explosive unless " gas " or methane is present , though perhaps in small amounts not detectable by a safety lamp . The experimental tests beginning in 1909 at the Pittsburgh testing gallery, and after 1911 , at the Experimental mine , demonstrated to the mining public the explosibility of coal dust in itself . There followed much controversy , both among practical mining men and scientists , as to whether the coal-dust particles uni te directly with the oxygen of the air, or whether gas is instantaneously distilled from the dust prior to explosive combustion , the gas enveloping each particle and propagating the flame from one to another . In considering methods of preventing explosions , this question made no difference for practical purposes , but it did have bearing in determining the relative inflammability of dusts of different coals . This led to the experiments by Guy B. Taylor and Horace C. Porter , on the momentary heating of the inflammable coal dusts , reported in this paper . Meanwhile , experiments on the inflammability of coal dust conducted in the Experimental mine , under my direction , and in the laboratory by J. C. W. Frazer and later by J. K. Clement and J. N. Lawrence , showed that different kinds of coal dust differ markedly in inflammability , thus confirming experiments made by Messrs . Taffanel and Durr at the Lievin Testing Station , France , and by various investigators in Great Britain . Both the French and British investigators concluded that their experiments demonstrated the distillation of volatile matter preceding inflammation .

Jan 1, 1922

By Sabri Ergun

This report gives the result of investigations of coals of different rank, coal com¬ponents, chemically and thermally treated and irradiated coals, and sedimented organic matter. In most studies the arbitrary parameters obtained from the usual quantitative profile analyses are not given largely because they lack physical meaning. Instead comp interpretations are offered. X-ray patterns of high-volatile bituminous and lower rank coals are not self¬-sufficient for structural interpretation by the methods of analysis developed to date. The patterns of hydrogenated and dehydrogenated coals indicate that the basic change in the structure of bituminous coals with increase in rank is the conversion of alicyclic structures into aromatic layers. In low-rank anthracites the aromatic layers are about 10 A in size. The increase in rank is the result of coalescence of layers. High-rank anthracites have layer sizes of 25 to 40 A and exhibit the development of three-dimensional (hkl) reflections of graphite, indicating ordering of adjacent layers. In meta-anthracites the layers are > 1000 A and the basic structure is that of defective crystalline graphite. The well-known petrographic components in low-rank coals have different structures; the differences dissappear in low-volatile bituminous and higher rank coals. The patterns of sedimented organic matter, except impsonites, differ from those of coal hydrogen contents are high, and their X-ray patterns are consistent with those of structures. In contrast to normal coals, the patterns of uranium-bearing coals show increased diffuseness with decrease in hydrogen content. The diffuseness is accompanied by increase in the uranium content of the coal. It is very likely that high uranium-bearing coals have predominantly tetrahedral structures.

Jan 1, 1968

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules3 include 13D for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pittsburgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer4 of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By Roger L. Williams

The Bureau of Mines investigated northern New Jersey as a potential future source of yttrium and the rare-earth elements. The studies, consisting of geophysical surveying, sampling, and exploratory drilling, began in the spring of 1959. A total of three and one-half months were spent in the field collecting data. Thirty-three deposits were investigated, of which five demonstrated some potential resources of yttrium and rare-earth minerals. Results indicate that the deposits examined do not contain quantities of yttrium and the rare-earth elements recoverable under present economic conditions. Detailed studies conducted at the Scrub Oaks mine, near Dover, N. J., delineated a yttrium and rare-earth-bearing zone within the magnetite-hematite ore body that represents a potential low-grade deposit. Beneficiation studies on this deposit indicate that a final product, averaging 31.3 percent rare-earth oxides including yttrium, could be produced through amine and fatty acid flotation procedures with 77 percent recovery. Two hundred and eighty-five feet of diamond drill core was obtained from exploration studies conducted at the Bemco prospect in Sussex County. The deposit averages 2.30 percent rare-earth oxides (including yttrium), 0.45 percent uranium and 0.24 percent thorium. Low-grade deposits were identified at the Canfield phosphat2 mine and the Tanners Brook Monazite placers in Morris County, and the Marble Mountain prospect in Warren County.

Jan 1, 1967

An independent contractor is defined by the Mine Safety and Health Administration (MSHA) as ?any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine.? Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Aug 1, 2009

By Edward L. Wilson

A general computer program is given for the linear elastic static analysis of complex structural systems. These elements have special advantages for the analysis of massive underground structures such as mine structures and above ground structures such as arch dams. New finite elements are developed which are useful in the analysis of two and three dimensional solids. Examples are given which illustrate the accuracy of the elements. A description on the use of the program and a FORTRAN IV listing are given in the Appendices.

Jan 1, 1971

By D. J. Stoops, H. Kato, M. D. Carver

The effects of impurity elements silicon , aluminum, copper , nitrogen , and manganese , at 50 to 300 ppm, on properties of the zirconium alloy Zircaloy 2 were investigated . Variations in microstructure , mechanical properties , and corrosion behavior in some inorganic acid and salt solutions were observed with variations in level of impurity element . Corrodents were solutions of sulfuric acid , phosphoric acid , copper chloride , and iron chloride . Silicon was found to modify annealed microstructures by spheroidizing and dispersion of secondphase material throughout grains . Silicon or manganese improved ultimate and yield strength of the alloy without loss in ductility . All five elements affected corrosion rates of the alloy , the effect being generally different for each element .

Jan 1, 1964

By Chas. E. van Baraeveld

"The information presented in this report is a by-product of studies concerning zinc, and is published in response to various inquiries for information as to the suitability of zinc for roofing. It parallels a previous report of the Bureau of Mines on slate roofing.Available Forms of Zinc RoofingZinc is available for roofing in three forms: 1. As sheet zinc which may be used advantageously on roofs with as flat a pitch as 1 in 4; laid with standing seam construction for small roofs and with batten construction for large roofs. 2. As corrugate sheets, in widths up to 40 inches and in lengths up to 8 and feet, available for siding and roofing in industrial buildings (with certain re¬strict ions) and or farm buildings (without restrictions). 3. In the form of shingles.Advantages of Zinc Roofing1. Zinc is a permeant roofing material; that is, when suited to the conditions, and properly applied to a roof designed with the right purlin spacing it will outlast the building and still have a salvage value equal to a least half the original material cost. It is applicable to a wide range of conditions, from the most expensive to the cheapest type of construction, and is not greatly above the cheaper materials in first cost. A permanent roof of simple outline need not cost over $15 to $25 per square (100 square feet), depending upon the method of construction required a corrugated sheet roof for industrial purposes or for farm use need not cost over $15 per square for ordinary conditions. 3. Corrugated zinc sheets have the distinct advantage of being available for re-use and re-construction if handled with ordinary care. 4. Zinc oxidizes to a certain point, building up a strong protective coating which in time effectually checks further oxidation; thus it does not oxidize to the point of destruction as steel does, 5. It is light and easily handled."

Nov 1, 1924

By J. M. Stuve

Low temperature and high-temperature calorimetric measurements were made by the Federal Bureau of Mines on high-purity samples of Re02(s) and Re03(s) to determine heat capacities and enthalpies. The temperature range of heat capacity measurements was 5 to 310 K for Re02 and 8 to 309 K for Re03. High-temperature enthalpy measurements alone were determined for pure Re207(s,1). The derived standard entropies are S°298 = 11.43±0.01 cal/deg mole for Re02(s) and S298 = 16.55±0.02 cal/deg mole for Re03(s). High-temperature enthalpy equations expressed in calories per mole are as follows: Re02 (s) , H-H298.15 = 16.002T + 1.600 X 10-3T2 + 3.522 X 105T-1 - 6,095 (298 to 1,400 K); Re03 (s) , H-H298.15 = 20.293T + 3.238 X 10-3T2 + 3.950 X 105 T-1 - 7,664 (298 to 1,000 K); Re207 (s) , H-H298.15 = 38.437T + 10.309 X 10-3T2 + 4.315 X 105 T-1 - 13,824 (298 to 413 K); Re207 (s) , H-H298.15 = 30.181 + 17.713 X 10-3T2 - 10,612 (413 to 600 K) ; Re207 (1) , H-H298.19 = 66.101T - 10,092 (600 to 700 K). Gibbs energy of formation (?Gf°) data and related functions over the temperature ranges investigated are tabulated for the three oxides.

Jan 1, 1976

By R. L. Soderberg

This paper is one of a series on mining methods and costs being published by the Bureau of Mines. It describes briefly the mining methods employed since the start of operations in 1937, with emphasis on the diamond-drill blast-hole method of ore breaking and slusher-drift method of ore drawing at the Holden mine of the Howe Sound Co., Chelan Division, Holden, Wash. The Holden mine is in the north-central part of the Cascade Range, 11 miles up Railroad Creek from Lake Chelan. The nearest railroad is at Chelan Falls, 40 miles by boat and 4 miles by highway from the mine. All freight comes into the mine and all concentrates are shipped out via Chelan Falls. The altitude of the main haulage level is 3,500 feet. Railroad Creek Valley is covered with a dense growth of fir and spruce, while most of the surrounding mountains are rocky, with sparse timber growth.

Jun 1, 1948