Search Documents

By Nancy Potts, M. G. Barker, W. C. Holliman

"SUMMARYThis report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, end 10 grade 115/145 aviation fuels.The inspection test data supplied by the participating manufacturers consist of octane and performance numbers, tetraethyllead content, dye color, and other characteristics usually listed in aviation gasoline specifications, such as AN-F-48a or ASTM Designation D910-47T. These data are tabulated and averaged by grades in tables 1 through 4 and, as reported, meet the AN-F-48a and similar specifications with a few exceptions. Two grade 80 gasolines show a lean-mixture octane rating slightly below 80.0, and 91/98 grade fuel shows a lean-mixture rating of 90.9 and a rich-mixture rating of 97.5, two 100/130 grade gasolines have a rich-mixture performance number slightly below 130.0, and one 115/145 grade gasoline shows a rich-mixture performance number of 144.5. However, octane and performance number averages are above the mini¬mum requirements for each grade. Tetraethyllead content in the 91/98 and 100/ 130 grades generally is above the maximum outlined in these specifications, whereas dye color for each of the four grades, with the exception of two gasolines in grades 80 and 100/130, is that designated for the particular grade. Distillation requirements, with a few exceptions at individual points, are met by gasolines of all grades. Reid-vapor-pressure, copper-dish-residue, heat-of-combustion or aniline-gravity-constant, freezing-point, and copper-strip-corrosion requirements are met by all gasolines so far as reported. No data for some of these tests wore submitted on a few of the gasolines. One gasoline, grade 115/145, shows a sulfur content greater than the specified maximum."

May 1, 1948

By Arno C. Fieldner

In view of the widespread interest in the production of synthetic liquid fuels from solid and gaseous fuels to supplement declining reserves of petroleum, and the many requests that are now being received for information on the subject, this bibliography of Bureau of Mines contributions has been compiled. In addition to the publications issued by the Government in printed or mimeographed form, references are included to articles written by the Bureau staff for the technical press and to cooperative reports of work done jointly with States, colleges, and industries. References are given under each section in chronological order. Bureau of Mines bulletins, technical papers, and Minerals Yearbooks are printed and are obtainable at the prices indicated from the Superintendent of Documents, Government Printing Office, Washington 25, D. C. If no price is given, the publication is out of print. The price of entire volumes of the Minerals Yearbook or of reprints of certain chanters may be obtained upon request. Any orders or remittances in payment for these publications should be cent directly to the Superintendent of Documents and not

Jan 1, 1945

By Robinson Newcomb

Gypsum is a form of hydrated calcium sulfate (CaS04.2H20) which is widely distributed over the earth's surface. The two varieties worked commercially are rock gypsum and incite. Rock gypsum, the variety commonly mined for commercial purposes, is a relatively soft mineral having a specific gravity of about 2.3 and weighing about 150 pounds per cubic foot. The chief producing States are New York, Michigan, and Iowa. Before being used the crude gypsum is ground and generally calcined. The predominant use of gypsum is for building purposes (the manufacture of plaster), for which calcined gypsum is required. Gypsum is also used as a retarder in Portland cement, as fertilizer, and for other purposes. GYPSUM MINING Crude gypsum is mined by two methods - underground and open-pit. Although the use of the former method predominates, open-pit mining increased in relative importance during the early twenties and contributed about two-fifths of the output during the period 1925-38.

Jan 1, 1940

This information circular describes research the Bureau of fines has conducted to improve technology for recovering precious metals from low-grade resources. Many of the reported findings are recent, and some of the work described is ongoing. Topics discussed include cyanidation of carbonaceous gold ores to enhance gold recovery, a new method for precipitating mercury during cyanide leaching of gold ores, a staged heap leaching process to generate suitable solutions for direct electrowinning of gold, the use of anion-exchange resins to recover gold from cyanide solutions, and precious metals recovery from electronic scrap.

Jan 1, 1986

By Rethel L. Hubbard

Fourteen straight-run asphalts were prepared in the laboratory from bitumens obtained from three sources: (1) native bitumen from Rozel Point, Utah, (2). bitumen extracted from Athabaska bituminous sandstone at Canada, and (3) bitumen extracted from Edna bituminous sandstone outcropping in San Luis Obispo County, to seven asphalts with penetrations ranging from 19 to 287 at 77 F. were prepared from each of the bitumens. The yields of the prepared asphalts ranged from 74.5 percent for a 27-penetration asphalt from the Athabaska bitumen to 99.5 percent for a 271-penetration asphalt from the Rozel Point bitumen.

Jan 1, 1949

By J. M. Stuve

In this Bureau of Mines investigation, the low-temperature heat capacities of polycrystalline phases corresponding to the sulfide compounds CoSO?89' CoS1?33, and CoS2 were measured by adiabatic calorimetry within the nominal temperature range 5 to 300 K. The derived absolute entropies S298 were 10.36±O.02, 12.96±O.03, and 16.31±O.03 cal?mol-1?K-l, respectively, assuming third-law behavior. In addition, the standard enthalpy of formation 8Hf298 of CoSO?89 was determined by bromine solution calorimetry. The derived value of 8Hf298 was -50.63±2.1 kcal?mol-1, based on the 8Hf298 of Co0. This result is considerably more negative than previously published formation values based on high-temperature gas equilibrium studies.

Jan 1, 1985

By Lindsay D. Norman

Eleven major pyrometallurgical processes and operations suggested for recovering manganese from domestic resources are described. These include seven pyrometallurgical processes that usually yield a ferroalloy or a product from which ferromanganese can be produced in one operation. The remaining four involve pyrometallurgical operations whose products require either an additional two-stage process to produce ferromanganese or chemical processing to recover a high-quality manganese oxide product.

Jan 1, 1962

By D. M. Lewis, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, J. H. Kang, V. Castronova

"Tetrandrine is a bisbenzylisoquinoline alkaloid which has been shown to exhibit antifibrotic activity against silicosis. Tetrandrine is characterized by its strong binding to alveolar macrophages and inhibition of particle-induced respiratory burst activity in these phagocytes. In contrast, tubocurine and tubocurarine are structurally similar to tetrandrine but exhibit little effect on fibrosis or activation of alveolar macrophages. The objective of the present study was to test the effect of tetrandrine on macrophage production of monokines in response to occupational dusts, and to determine tetrandrine's effect on monokine-medicated cell growth using a mouse thymocyte proliferation assay and lipopolysaccharide (LPS) as a positive control. Stimulation of alveolar macrophages by respirable silica dust resulted in a release of monokines which caused a fourfold increase in thymocyte proliferation. Coal dust, on the other hand, had no effect on macrophage production of this cytokine. Tetrandrine was found to exhibit a dose-dependent inhibition of monokine release from both silica and LPS-stimulated alveolar macrophages. In experiments where thymocytes were directly treated with tetrandrine, a dose-dependent inhibition of thymocyte proliferation was noted with both interleukin-1- (IL-1) specific and nonspecific mitogenic (concanavalin A) actions. In contrast to the inhibitory potency of tetrandrine, tubocurarine was found to have no effect on either the production of monokines by LPS-stimulated alveolar macrophages or IL-I-mediated thymocyte proliferation. These results provide a correlation between the ant:fibrotic effect of tetrandrine and inhibition of macrophage activation. INTRODUCTIONThe pathogenesis of chronic pulmonary fibrosis caused by inhalation of occupational dusts has been associated with abnormal activation of alveolar macrophages such as the release of various cytokines capable of inducing fibroblast proliferation and collagen synthesis. These macrophage-derived cytokines include interleukin-1 (IL-1), tumor necrosis factor (TNF), platelet-derived growth factor (PDGF), transforming growth factor-B (TGF-(B), macrophage derived growth factor (MDGF), and interferon [1, 2].Interleukin-1 is a major macrophage-derived cytokine that has been shown to exhibit multiple biological effects on a variety of target cells. It is known to cause leukocyte [3, 4] and endothelial cell activation [5, 6], and to affect the synthesis and maintenance of the extracellular matrix by stimulation of fibroblast proliferation [7-9], synthesis of collagens [10] and gluco-saminoglycans [11], and prostaglandin E2 production [12]. In addition, IL-1 plays an important role in the initiation of an immune response through its direct activation of lymphocytes and stimulation of the production of other cytokines, such as interferons and hemopoietic colony-stimulating factors, needed for the expression of an immune response [13]. As a major cytokine in the immune-inflammatory sequela, IL-1 is also produced by epidermal, epithelial, lymphoid, and vascular tissues after infection, injury, or antigenic challenge [14]. Agents such as lipopolysaccharide (LPS), phorbol myristate acetate (PMA), immune complexes, and particulates are known to activate the synthesis and release of IL-1 by monocytes and macrophages [15]. These substances also trigger intracellular signals leading to altered arachidonic acid metabolism. Although the mechanism is still not clear, prostaglandins have been shown to suppress IL-1 translation via the induction of cyclic adenosine-monophosphate (CAMP), whereas leukotrienes produce a positive signal for IL-1 production [13]."

Mar 1, 1992

By Th. G. Sahama

This paper contains some new heat-of-solution measurements of geikielite (MgTiO3), limonite (FeTiO3), fayalite (Fe2SiO4), and a natural forsterite in mixed acid (HF +HCl) and gives the results of a thermodynamic attack on the problem of stability of geikielite in rocks.

Jan 1, 1949

By O. S. North

As recently as the late 1920's there Were few indications that a 15-million-dollar-a-year industry would ever grow out of the mineralogic curiosity vermiculite. Today, it is an important industrial commodity, used primarily as an insulating material and lightweight aggregate, but with a wide range of other applications. The quantity of crude vermiculite produced and used in the United States increased 14-fold in the 17 years between 1935 and 1951. The vermiculite minerals are of secondary origin, formed by hydrothermal alteration of an ultrabasic igneous rock, generally pyroxenite, or by alteration of phlogopite or biotite mica or possibly other similar minerals. According to different authorities, vermiculite may originate either by direct hydrothermel means, by the weathering of biotite or phlogopite, or by a combination of these two agencies. Vermiculites frequently occur at or near the contacts of an acid intrusive rock, especially a pegmatite dike, with a basic or ultrabasic country rock.

Jan 1, 1953

By H. D. Hess

This report presents the results of laboratory mineral evaluations conducted by the federal Bureau of Mines under the joint sponsorship of the U.S. Atomic Energy Commission (AEC) and the Bureau a! Ships, U. S. Department of the Navy. The major purpose of this investigation was to examine and evaluate zirconium minerals representing sizeable deposits in an effort to locate com¬mercial sources of high-hafnium ores. Although determination of the hafnium content was the principal objective, each of the zirconium minerals also was analyzed for combined zirconium-hafnium oxide, silica, uranium, thorium, yttrium, and cerium. The general laboratory procedure involved microscopic examination of the test samples, concentration of the hafnium-bearing zirconium mineral by standard laboratory techniques, and analysis of the derived concentrate by quantitative microscopic, chemical, and X-ray spectrographic methods. Of the several hundred samples tested under this program, 147 are discussed in this report, including 94 from domestic occurrences and 53 from widespread foreign sources.

Jan 1, 1962

By C. C. Hwang

The Bureau of Mines made time-dependent calculations to determine the size of a stationary source fire within a ventilated duct (or passage-way) necessary to ignite a combustible duct liner. The objective of this work was to gain more understanding of what occurs in duct fires and to determine critical conditions for ignition and propagation of mine fires. Heat transfer to the combustible surface includes both convective and radiated components, while the heat is conducted into the combustible and reradiated to the surroundings. The combustible is assumed to ignite when the net heat transfer to its surface is sufficient to raise the surface temperature to some minimum temperature, defined as the ignition temperature. A nondimensional parameter, which characterizes the source-fire intensity in the presence of ventilation flow, emerges as a parameter for a criterion of the critical conditions. The results of these calculations indicated that the minimum fire size necessary for ignition increases with the ventilation rate and duct cross section. These results are compared with experimental results obtained from fires in a 0.8-by 0.8-by Il-m-long duct and a full-scale gallery (2.4-by 2.4-by 65-m). Agreement between the theory and the experiment is good.

Jan 1, 1988

A construction material based on plasticized sulfur and mineral aggregate, that is superior in corrosion resistance and strength to portland cement concrete. The material can be used in the chemical, metallurgical, and fertilizer industries, and will also provide an attractive market for by-product sulfur resulting from compliance with pollution regulations. How It Is Made Sulfur concrete is thermoplastic material. Plasticized sulfur is mixed with sand and gravel aggregate heated to 375-400° F. The sulfur melts and acts as the binder or cement. The sulfur concrete is poured hot and sets at a temperature of 200° F. Full strength is attained in a few hours, compared to several days for portland cement concretes. Sulfur concrete even pours and sets in freezing weather. Although unmodified sulfur with aggregate will produce a sulfur concrete with good initial properties, it undergoes crystallographic modifications, and deteriorates with time, particularly when exposed to moisture or freeze-thaw conditions. The Bureau of Mines has developed plasticizers which, when reacted with the sulfur, give sulfur concretes with excellent moisture and freeze-thaw resistance. The plasticizers are based on mixtures of dicyclopentadlene (DCPD) and ollgomers of cyclopentadiene. About 5 percent by weight of the plasticizers is reacted with molten sui fur for several hours. The sulfur cement can be used directly or allowed to solidify for easier handling and storage.

Jan 1, 1981

By W. R. Hardwick

This Information Circular describes the development of block-caving methods and practices by the Miami Copper Co. at the Miami mine in Gila County, Arizona. It is one of a series published by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. This report gives a history of the district and outlines early prospecting and exploration including methods of sampling and estimation of ore tonnage and value at the Miami mine. Early mining methods are described, particularly those that influenced developments in the caving method. Mine exploration, development, and operating methods for block caving are described with particular attention to those factors, physical, economic, engineering, and managerial that have improved efficiency in the mining operations over a long productive period. Extraction, ventilation, wage system, safety, water supply, power plant, and shop facilities are discussed. The last section gives a brief sumary of such costs as are available for publication.

Dec 1, 1964

By David M. Gullikson

As part of its program of petroleum production research the Federal Bureau of Mines has long been engaged in the study and development of systems of analysis of oilfield waters (8, 12, 20, 21, 22, 27, 30).21 However, many of the early chemical procedures developed by the Bureau and widely adopted by the petroleum industry are time consuming, and some are unreliable for determining certain constituents found in California oilfield waters. Because of the need for more rapid and more accurate methods having greater sensitivity with low concentrations of some constituents, a study has been made by the Bureau's Petroleum Research Laboratory at San Francisco, in developing new techniques and modifying previously published techniques for analyzing oilfield waters by flame spectrophotometric, potentiometric, and colorimetric methods. Test solutions were synthesized for testing the suitability and accuracy of the procedures, and the effect of interfering ions. These solutions contained known quantities of characteristic constituents of oilfield waters including sodium, magnesium, potassium, calcium, lithium, strontium, barium, sulfate, chloride, bromide, iodide, carbonate, bicarbonate and borates in a wide range of concentrations. The compositions of these synthetic brines are listed in table 22. Many California oilfield waters contain salts of petroleum-derived organic acids and several synthetic oilfield waters also were prepared to which large quantities of naphthenates or salts of petroleum acids were added.

Jan 1, 1961

By D. N. Nilsen

A mathematical modeling method was developed by the Bureau of Mines for the prediction of the principal equilibrium species in the solvent extraction of copper. The use of models for predicting the amount of metal extracted can reduce the amount of experimental work required to characterize a system for purposes such as optimization studies. Models were developed for the extraction of copper from ammoniacal sulfate and carbonate solutions with commercially available extract ants commonly used by industry. Results from laboratory shakeout tests compared well with predictions of the equilibrium concentrations of copper and pH values. For example, the loading of copper onto the solvent was predicted for most cases within ±S pct of the measured values, and the pH to with-in ±O.l pH unit in sulfate systems and ±O.2 pH unit in carbonate systems. Both mechanistic and empirical extraction equations were developed from laboratory data for copper and ammonia. The empirical-based models were slightly more accurate than were the mechanistic-based mod-els. Industrial level concentrations of the aqueous and organic constituents were used in this work. Independent variables included copper concentration, ionic strength, and initial pH of the aqueous phase; extractants, diluents, and their concentration in the organic phase; and temperature.

Jan 1, 1988

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan, J. H. Kang

"We have reported previously that crushing or grinding crystalline silica results in the generation of silica-based radicals on the particulate surface and that these radicals can generate hydroxyl radicals in aqueous solution. Data in the present study indicate that freshly ground silica is more cytotoxic and is a more potent activator of alveolar macrophages than comparably sized aged silica. That is, compared to aged silica, fresh silica is 4.2-fold more potent in decreasing the membrane integrity of macro· phages; is 50% more potent in activating hydrogen peroxide secretion by macro· phages; and is 4.frfold more potent in stimulating cellular chemiluminescence. Prosil 28, an organosilane material, is an effective coating agent for fresh silica. It decreases the cytotoxicity of fresh silica by as much as 78% and decreases the ability of fresh silica to induce chemiluminescence from alveolar macrophages by 58%. The data suggest that surface radicals associated with freshly cleaved dust may be an important factor in the induction of pulmonary disease. Furthermore, treating dust with coating agents may substantially decrease toxicity. INTRODUCTIONThe U.S. Department of Labor estimates that over 1.25 million American workers may be exposed to crystalline silica and that nearly 60,000 may be at risk of developing some degree of occupational lung disease (Parkes, 1982; Peters, 1986). Occupations of concern include miners, stone quarry workers, sand and gravel workers, sandblasters, foundry workers, and glass workers. Acute silicosis is characterized by inflammation, alveolar lipoproteinosis, and the rapid development of respiratory disability (Banks, 1986). In contrast, chronic silicosis develops 20-40 yr after initial exposure and is characterized by the appearance of concentric hyalinized nodular lesions and the progressive development of dyspnea (Parkes, 1982; Ziskind et al., 1976)."

Mar 1, 1992

By B. H. Eccleston

The effect upon automobile emissions in changing from leaded to lead-free gasolines was studied in experiments by the Bureau of Mines in cooperation with the American Petroleum Institute. Typical U.S. leaded gasolines and prototype lead-free gasolines of comparable octane quality were used in eight vehicles operated to simulate city driving. The experiments were run at 70° and 95° F. Exhaust and evaporative emissions were measured and the photochemical effect of the emissions was experimentally observed in an artificial smog chamber. Results of the study reveal the manner and degree in which the changes in fuel composition alter the amount and characteristics of both exhaust and evaporative emissions. Briefly, it is shown that the compositional differences between leaded and prototype lead-free fuels resulted in higher photo-chemical pollution potential of the emissions from the lead-free fuels. The effect is attributed to the photochemical characteristics of high-octane fuel components that are used in greater quantity in the lead-free fuels.

Jan 1, 1970

By B. J. Moore

This publication contains analyses arid related source data for 274 natural gas samples from 20 States. Of the total samples, 269 were collected during calendar year 1985; the reminder were collected earlier, but releases granting permission to publish were not received before 1986, All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1987

By L. F. Willmott

Pulverized high-volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure-gasification pilot plant equipped for slurry feeding. The minimum ratio of water to pulverized coal that could be pumped satisfactorily as a slurry was about 1 to 1. Heating this slurry produced a suspension of coal in superheated steam having a steam-to-coal ratio greater than the 0.3 to 1 proportion that is considered optimum for pressure gasification of pulverized coal. A steam separator removed enough steam to provide ratios down to about 0.5 to 1, but a 0.3 to 1 ratio was not achieved. Gasification of Sewickley coal produced a synthesis gas containing about 36 percent H2, 46 percent CO, and 13 percent CO2, Gas output, gas composition, and coal and oxygen requirements were Virtually the same as for a pilot plant equipped for fluidized-coal feeding. Typical results from the slurry-fed plant at 300 psig were carbon gasified, 95 percent; coal requirement, 34 lb/M (thousand) std cu ft CO + H2 produced; oxygen requirement, 365 std cu ft/M std cu ft CO + H2 produced. The results showed that the two feeding methods are equally satisfactory from the standpoint of gasification. A choice between a fluidized-coal gasification process or a slurry gasification process depends on considerations relating to the coal-feeding phase itself, including capital and operating costs, manpower requirements, safety, and flexibility of operation.

Jan 1, 1962