Search Documents

By Robert M. Becker

Part 5, the last of this series, deals with the theoretical confirmation and application of results developed in parts 1 and 2. The bulk-sampling variances of Hassialis and Kassel and Guy are compared with those in part 2, both as to formulation and as applied to ores and coal. The results provide confirmation for much of the development in part 2. Examples are presented for determining the reliability of bulk samples with respect to various measurable characteristics. These characteristics include, for example, assays for elements or compounds and particle surface area. The bulk samples considered consist either of a given weight, a given volume, or a given number of particles. In addition to problems of sample reliability, some of these examples may also be applicable to quality control. Several possible applications of results developed in parts 1 and 2 are outlined. These include tests for random data, degree-of-mixing indices, and particle-fineness indices.

Jan 1, 1966

By R. Blickensderfer

The laboratory wear testing capabilities of the Bureau of Mines are described, Wear tests are used to support the Bureau?s research efforts toward reducing the wear of equipment used for mining and minerals processing and any wear involving a loss of strategic or critical materials. The emphasis is on abrasive wear because it accounts for most of the wear losses that occur in mining and minerals processing equipment, Spalling wear, caused by repetitive impact in grinding equipment, also is included, Ten abrasive wear tests, including high- stress and low-stress and two-body and three-body conditions, are described: dry-sand, rubber-wheel abrasive wear; Taber Abraser; abrasion resistance of refractory materials; dry-particle erosive wear; elevated-temperature, dry-particle erosive wear; low-angle slurry pot; jaw crusher gouging wear; ball mill wear; pin-on-drum abrasive wear; and high-speed impact gouging. Two repetitive impact tests are described: ball-on-block impact-spalling and ball-on-ball impact-spalling. Test equipment, procedures, and specimens are described, and typical test results are presented and discussed.

Jan 1, 1985

By Guenter F. Lehmann

This report summarizes the results of the development and testing of a prototype monorail suspended bridge conveyor (MBC) system as a method of continuous haulage In underground mining applications. Included are the results of full scale, surface and underground testing of the complete MBC system. Conclusions drawn from these results, together with recommended modifications, supports the viability of the MBC system.

Jan 1, 1988

By Lowell Stroud

Ten natural gases containing from 0.023 to 8.4 percent helium were investigated. In seven high-helium samples, the isotopic abundance of Ne21 was greater than in the atmosphere, being supplemented by 33 to 85 percent of "excess" or "radiogenic" Ne21. The ratio of He4/Ne21(rad) in these gases was evaluated and found to vary between 2.9 x 107 and 5.9 x 107 , a factor of approximately 2. Argon concentrations were determined by the isotope dilution method. The isotopic ratios of Ar40/Ar36 in the high-helium gases were from 5 to 75 times the atmospheric value, with the Ar40 being about 80 to 99 percent radiogenic in nature. The ratios of He4/Ar40(rad) in all 10 gases were evaluated and found to range from 4 to 18. The isotopic ratio of N14/N15 in four of the high-helium gases was essentially the same as in the atmosphere; in three cases it was approximately 5 percent higher than the atmospheric value of 272.0. The genesis of nitrogen and the relationship of nitrogen to helium in natural gases were reviewed and are discussed in terms of a theory for the concurrent generation of nitrogen, helium, radiogenic neon 21, and petroleum (hydrocarbon gases and liquids).

Jan 1, 1967

By Donald L. Siebert

This profile study of the commercial secondary aluminum industry examines not only the elements that form the industry but also the technological contributions of each toward industrial growth. Concise descriptions of processing methods trace aluminum scrap from generating sources to marketable industrial and consumer goods. Economic and marketing appraisals are used to illustrate the impact that recent technology has had upon the secondary aluminum industry. Price, supply, demand, competition, and substitutes are selected as components of an economic model of the secondary industry and are used to illustrate the aggregate effects of technological changes. The final section is a conceptual look at the future in which sensitive economic indicators (such as die casting in the automotive and appliance industries) are examined as well as the problems of conserving mineral resources by retrieving secondary aluminum from solid waste.

Jan 1, 1970

By Paul W. Johnson

Economic studies of four processes for using the glass fractions obtained from processing municipal incinerator residues are presented. Three processes--brick production, floor tile production, and glass wool production--use the colored glass fraction from an incinerator residue separation plant, and the fourth process, glass spheres production, uses the colorless glass fraction. The fixed capital cost and the estimated annual operating cost for six plants are presented in the report and summarized, as follows: [ ] The value of the product obtained from each of the plants was calculated on the basis of the interest rate of return method. Each of the processes appears economically attractive when comparing the product values with estimated selling prices. However, the effect of the products on market size and price must be determined.

Jan 1, 1973

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics are presented for air in a 2 - inch pipe - type electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig using a negative discharge electrode . Results of this one - geometry study show that current - voltage relationships are a function of air pressure and temperature and indicate that precipitators can be used at any temperature through about 1,350 ° F over the full range of pressure . Corona starting voltage and sparkover voltage vary directly with pressure and inversely with temperature . At temperatures above 1,350 ° F use of precipitators may be limited to operations at pressures somewhat above atmospheric pressure . Theoretical derivations are presented that relate the effect of gas density on corona starting voltage and the effect of ion mobility on corona current . Deviation from the theory is noted at high current levels . Theoretical discussion is presented to explain the apparent electrical limitations for use of precipitators at high temperature , low gas density , and high corona currents , conditions at which calculated ionic velocities are extremely high . Experimental results are interpreted in terms of the theory presented . 1,500 ° F thermal ionization does not appear to be a critical factor .

Jan 1, 1963

By W. W. Adams, T. D. Lawrence

"The National Safety Competition of 1938, the fourteenth of its kind conducted by the Bureau of Mines in which bronze trophies known as Sentinels of Safety are awarded to winning companies, has just been completed and the results are presented here.With 345 mines and quarries competing, more than in any previous year except 1931, the contest revealed low accident rates at many of the enrolled plants and, which is even more remarkable, it revealed 113 mines and quarries at which no lost-time accidents occurred during the contest year.The Sentinels of Safety trophies, provided by The Explosives Engineer magazine, were awarded to four underground mines, one open-pit mine, and one quarry. Each employee of the winning plant was awarded a Certificate of Honor by the Bureau of Mines in recognition of the employee's part in helping his company to win the trophy. In addition to the award of trophies, a Certificate of Honorable Mention was awarded to each of the mines and quarries in second, third, fourth, and fifth places in their respective contest groups and also to each mine and quarry that worked 30,000 or more man-hours without a lost-time accident. Ninety-two such certificates were awarded for 1938. Twenty-three other mines and quarries also operated without an accident but worked less than 30,000 man-hours, the minimum required by the contest rules for award of Certificates of Honorable Mention.Previous to 1938, five trophies were awarded annually in the National Safety Competition. For the 1938 contest a sixth trophy was provided by The Explosives Engineer so that open-pit mines and quarries, two classes of operations that previously had been included in one group in the competition, might have separate awards."

Aug 1, 1939

By J. M. Singer

Methods are proposed for predicting concentrations of nitrogen oxides and carbon monoxide in the combustion gases of flames, specifically of lean, stoichiometric, and rich propane-air flames. Calculations are based on kinetic and thermodynamic theory. These theoretical data are compared with concentrations observed experimentally downstream of flat grid-type burner flames (approximately 25,000 Btu/hr) that were used to simulate gas appliances such as water and space heaters. Air pollutant concentrations are also computed for (1) flames chemically perturbed by recycling flue gases into the primary fuel-air mixtures; (2) flames thermally perturbed by cooling the burned gases at different rates; and (3) flames perturbed by combination of these two effects. In general, experimental and computed concentrations agree to within a factor of 2 to 7 with the experimental values always being higher than the theoretical. The theoretical analysis indicates that cooling the primary flame by recycling cold flue gases (with and without excess air) reduces the relative emission of nitric oxide and increases emission of carbon monoxide if the flame stoichiometry does not radically change. Cooling rates of about 5,500° to 10,000° R/sec starting at about 3,500° R generally suffice to prevent nitric oxide concentrations in lean flames from increasing much above the initial values at the combustion zone; these same cooling rates do not prevent oxidation of most of the initial carbon monoxide.

Jan 1, 1967

By D. J. Parker

State governments are increasing their efforts each year toward promoting the safety of miners .. Accidents underground are being avoided and mines made safer by means of revising and adding to their mining laws , by enforcing them through mine inspection departments , and by hearty co - operation with other agencies working miners ' safety . The U. S. Bureau of Mines is glad to testify to the co -operation that it receives from State mining departments in its safety work ; reports of the field mining engineers of the Bureau bear witness almost daily to the efforts of the States toward safety in mining . * This Through the courtesy of Mr. William Ogilvie , District State Wine Inspector of District No. 2 , with headquarters at "cAlester , Oklahoma, the Bureau has been furnished with a copy of a letter sent to various mining companies of Mr. Ogilvie's district in Oklahoma, relative to safety in Oklahoma mines . letter shows both the vigorous efforts which the State of Oklahoma is making toward increased safety in mines , and the recognized value of the types of electric cap lamps approved by the U. S. Bureau of Mines as " permissible " for use in gaseous mines ; it is accordingly reproduced in part : "hen during my first inspections of several coal mines in the district I found gas , or fire- darp being given off more or less constantly from the freshly cut coal at numerous points throughout the mines , I became uneasy relative to safety conditions , and am still considering your safety from many angles , but I am more concerned about the gas given off and the coal dust produced daily, than any other factor at the present time .

Jun 1, 1922

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987

By L. Garner McDonald

The U.S. Bureau of Mines, under contract to the U.S. Department of Energy, investigated the erosive-wear properties of seven commercial alloys with potential applications as valves for coal-conversion plants. A dry particle, jet-erosion apparatus was used to determine the wear of seven materials: 316 and 440-C stainless steels, K-68, K-701, and K-801 cemented tungsten carbides, HC-250 white cast iron, and Haynes 6B. The alumina abrasive entrained in the nitrogen gas jet had particle sizes of 27 or 50 µm, the abrasive velocities were 55 to 170 m/s, and the particle impingement angles were 15° to 90°. The maximum specific wear for ductile materials was found to occur at impingement angles of 15° to 30°, and the minimum specific wear occurred at 60° to 90°. For the brittle materials, maximum specific wear occurred at impingement angles of 50° to 85° and minimum specific wear was at the lowest angles. As the velocity and erosive particle size increased, the specific wear increased. The specific wear was related to the velocity by the power function WocAVn, where n was 1.8 to 3.9 for ductile materials and 1.8 to 3.6 for brittle materials.

Jan 1, 2010

By G. L. Oldright

The data in this paper were collected at the Trail smelter of the Consolidated Mining & Smelting Co. of Canada, Limited, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent; George Murray, assistant smelter superintendent; and the staff members given in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the thirteenth of the series on Smelting in the Lead Blast Furnace, and the third of the series on Handling Zinciferous Charges. Tyro other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

By R. R. Lowery

The Bureau of Mines developed hypereutectic aluminum-silicon alloys which 11.7.d better mechanical properties than the unmodified hypereutectic alloy. A commercial aluminum-20 weight-percent silicon LIr alloy was selected as a ary base for improvement. The primary silicon. grains were reduced from ASTM 4-5 to ASTM 8.5 by the use of phosphorus and phosphorus compounds. The remaining eutectic matrix was refined by sodium metal additions of 0.2 weight-percent. Solid solution strengthening of the alpha aluminum was obtained by adding 2 percent copper and 0.5 percent magnesium. Also, 1 percent nickel was added to harden the alloy. Optimum thermal treatment consisted of a solution treatment for 10 hour:, at 480° C with hot water quench, followed by aging for 6 hours at 175° C. The final alloy exhibited a Rockwell B hardness of 75 ±2 in the heat-treated condition. The ultimate tensile strength was 39,5O0 psi with no recordable elongation. The coefficient of linear thermal expansion was 20.4 x 10-6 per °C in the temperature range 20° to 300° C. No wear resistance data were collected.

Jan 1, 1966

By C. C. Hwang

The Bureau of Mines formulated a method for calculating the concentration of entrained dust from a dust deposit by a turbulent gas stream. In particular, a diffusion equation is used to calculate dust concentrations in a channel following an explosion. Dust leaving the channel walls was treated as originating from stationary or moving, and single or multiple material sources. Formulas and sample computations for various types of dust sources in circular and rectangular channels are given, based on experimental entrainment rates. The analysis predicts the dust concentration as a function of time and channel space. The results appear to agree with the physical characteristics of explosion-driven dust dispersion in a O.6-m-diameter, 50-m-long explosion tunnel. The analysis is also applied to simultaneous and consecutive dispersion of coal and rock dust from simulated coal mine surfaces (walls, floor, roof, and ribs).

Jan 1, 1974

By H. W. Kilau

The Bureau of Mines evaluated synthetic fluorspar as a substitute for natural fluorspar flux in basic cupola ironmaking. The synthetic fluor-spars tested were prepared from waste fluosilicic acid generated during the processing of fluorapatite ore. The cupola trials showed the synthetic products to be the equivalent of natural fluorspar from an operational standpoint. However, wet scrubber sampling showed that substantial losses of volatilized fluorine occurred from the cupola during operation. The losses during synthetic fluorspar trials considerably exceeded those from natural fluorspar trials. Laboratory viscosity testing, using a high-temperature rotational viscometer, confirmed this finding and indicated that fluorspar volatility in slags is related to slag basicity. Synthetic fluorspar is accordingly recommended more for highly basic cupola operation (>1.3 basicity) than for neutral or acid operation, because of the increased potential for pollution and baghouse filter detezioration"

Jan 1, 1989

By Perry D. Teitelbaum

In two earlier studies the Federal Bureau of Mines undertook to explore comprehensively the dimensions of the Nation's energy balance. The first of these studies, published in 1950 as Bureau of Mines Information Circular 7582, by Harold J, Barnett, was primarily concerned with projections of future domestic energy requirements and supplies, because these related to projected growth in major fuel-consuming sectors of the economy, changing rates of energy-use efficiency, and interfuel substitution patterns. But, to provide the essential background for these projections, it was first necessary to assemble and examine in some detail the quantitative information on the size and shape of the current United States fuel economy. Among other things, Barnett's path-breaking study indicated the need to consider energy as an entity, particularly for public and private policy makers, industry and commodity analysts, economists, and others concerned with long range questions of domestic and international energy supply and demand. The study also spotlighted a gap in the fabric of current economic intelligence; no comprehensive collation and reconcilation in any single report of available published statistical information covering the origin -a disposition of all energy materials existed. In response to this latter need, the Bureau of Mines prepared the second of the two studies referred t3 above. This was published in 1951 as Report of Investigations 4805, by W, H, Lyon and D, S. Colby, and it consisted of statistical information on the production and use of each of the various fuels and electric energy in the United States for 1929, 1939, and 1947; all were presented in tabular form and on a uniform basis. The three years selected were chosen largely on the basis of data availability.

Jan 1, 1961

By Jr. Koch

Statistical methods applied at the Bureau of Mines Denver Mining Research Center to data from metallic ore bodies were used to evaluate lignite reserves from core data and to predict the extent of lignite horizons in some Texas lignite beds. Six lignite seam units were studied using data from 361 drill holes. The data indicate a total of 214.2 million tons of lignite in the area examined, and probable reserves of 113 million tons in an area 2,000 feet beyond the limits established by the drill holes. It was demonstrated that lignite reserves present in lenticular beds could be reliably determined by statistical techniques, and that core drilling could be optimized to maximum information with minimum drill holes. The technique described is applicable to other coal beds.

Jan 1, 1966

By E. C. Lane

[This Is the ninth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the interior. The first report gave data on motor gasoline sold during the winter of 1935-36.3/ The Present report presents analytical data for 2,033 samples, representing the products of approximately 80 companies, which, as in previous surveys, include both large and small suppliers. In addition, the Pacific coast is represented by data that were average by the Pacific Coast Technical Group before 'being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. The cumber of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, arc as follows: Regular price, 1,066 samples, 208 items, and 49 brands; premium price, 575 tamales, 154 items, and 38 brands; third-grade gasoline, 7;4 samples, 150 items, and 53 brands. The meanings of these terms as used in the surveys tar as follows: Sample: The individual supply of gasoline obtained at the filling station and analysed in the laboratory.]

Jan 1, 1940