Search Documents

By Uwe Kaulbars

Vibration measurements at the workplace are often complicated and expensive. The assessment of the risk in conformity with EC Directive 2002/44/EC “Vibration” (which lays down the minimum requirements of laws in Europe for occupational safety and health) can therefore be carried out on the basis of an estimate based on information from manufacturers as well as by measurement conforming to ISO 5349. The characteristic values (emission values) determined by manufacturers in laboratory conditions may deviate from the exposure values measured at source at the workplace. Equally, deviations may arise as a result of the delay in the changeover of test methods from the single axis of measurement to the total vibration value for the three axes of measurement conforming to ISO 20643. To prevent faulty estimates, the manufacturer’s information has to be corrected by a tool-related factor in accordance with CEN/TR 15350. By taking the example of masonry and stone working machines, the empirically determined tool-related correction factor is checked and confirmed. Methods Vibration measurements were carried out in accordance with ISO 5349 in practical application conditions on 10 selected typical eccentric and orbital sanders, concrete and disc grinders as well as on wall chasers and stone saws. Results The total vibration value obtained for the investigated tools rangedfrom ahv = 3.6 m/s² to ahv = 11.6 m/s². When the values from the practical measurements are compared with the manufacturer’s vibration values, the underestimation of the risk occurring in some cases can be largely compensated for by the tool-related factors conforming to CEN/TR 15350 (see Figure 1).

Jan 6, 2006

By D. W. Bridges, L. Crocker, R. O. Dannenberg

About 95 pct of the beryllium was dissolved from most ore samples by agitation leaching with 600 lb of H2SO4 per ton of ore for 24 hours at 65 ° C and 35 pct solids . Leach slurries generally were viscous , and the limiting pulp density for thorough mixing was about 35 pct solids . Settling of the leached pulp required 0.6 to 0.8 lb of a polyacrylic flocculant per ton of ore leached with 600 lb of H2SO4 per ton , whereas ore leached with 800 lb of H2SO4 per ton required only 0.2 to 0.3 lb of flocculant per ton . Terminal densities of the settled pulps were about 28 and 35 pct solids , respectively , from leaches using 600 and 800 lb of H2SO4 per ton . Vacuum filtration of settled pulps at 15 in . Hg resulted in a filter cake containing 50 to 59 pct solids . Roasting the ore at 500 ° C before leaching increased the limiting pulp density for effective mixing to 50 pct solids . Acid requirements , however , were not diminished , although leaching roasted ore with 600 lb of H2SO4 per ton resulted in densification of settled pulps to about 40 pct solids . Filter cake from leaching preroasted ore contained about 20 pct less water than that from unroasted ore .

Jan 1, 1963

By B. K. Cantrell, K. L. Rubow

"Two source apportionment techniques have been applied by the U.S. Bureau of Mines to aerosol measurements in diesel-equipped underground noncoal mines. The first technique is based on size-selective sampling and the premise that the diesel exhaust fraction of the aerosol is predominately submicrometer in size while the mineral dust fraction of the aerosol is mostly supermicrometer in size. The second technique, chemical mass balance (CMB) modeling, was used to referee the analysis of diesel and mineral dust aerosol concentrations with the size selective method.The size-distribution data were modeled using a lognormal regression to parameterize the submicrometer and supermicrometer fractions of the sampled aerosol and to estimate the mineral and diesel contributions to each. Using this analysis, 97 ± 2 pct of the submicrometer aerosol mass was attributable to diesel exhaust aerosol.The CMB analysis, applied to both fractions of the respirable mi11e aerosol, yielded the amount contributed to each by the diesel and dust aerosol sources. On the basis of this analysis, 94± 10 pct of the submicrometer fraction was diesel exhaust aerosol. As much as 20 pct of the diesel aerosol, however, was found in the supermicrometer fraction, requiring a correction of the submicrometer fraction results to account for the missing diesel mass. More accurate measurements will require a carbon-specific analysis of the aerosol.INTRODUCTION Measurement of the contribution of diesel exhaust to respirable aerosol in mine environments has become increasingly important because of current concerns over the occupational health effects resulting from exposure to diesel emissions. In response to this, the U.S. Bureau of Mines is developing and evaluating new sampling methods for measuring diesel aerosol in underground mines. Two such techniques are being studied by the Bureau, size selective sampling and CMB modeling. These techniques use measurable physical or chemical characteristics of a mine aerosol sample to infer the amount of diesel particulate material contained in the sample."

Mar 1, 1992

By Otto Ruhl

"INTRODUCTION With the conclusion of the war and the ensuing readjustment of industry to peacetime conditions, the Bureau of Mines recognized that definite and complete figures on the reserves of zinc and lead ores in the Tri-State District would be needed for an evaluation of the problem of reconversion. In October 1945 its engineers began examination of all the mines and pros¬pects in the Tri-State area and assembling of the basic data for a complete detailed estimate of the reserves of the field. Six to twelve months will be required to complete the report with the personnel available; therefore, it has been deemed advisable to provide as much data as possible for imme¬diate use. Accordingly, a confidential report prepared in January 1944 for the use of and in cooperation with the War Production Board has been brought up to date to form the basis of this preliminary estimate of reserves.The 1944 report has been revised by first subtracting from the reserves then set up for each mill group the amounts mined and milled by those properties for 1944 and 10 months of 1945, with November and December estimated. These production statistics were taken from the monthly reports of the Metal Economics Division of the Bureau of Mines. The remaining reserves were then adjusted by additions of tonnages of new reserves disclosed by developments during the years 1944 and 1945. Such additions were based upon the data furnished by various operators, upon estimates supplied by the Federal Geological Survey District Office at Miami, Okla., and upon estimates of the engineers of the Bureau of Mines Joplin field office.It is apparent from the work so far accomplished in the detailed exami¬nations now under way that the final estimate of reserves will probably be somewhat greater and will differ to a certain degree from these preliminary totals, not only as to the tonnages of ere but also as to grades and distribution by areas. This is due to the fact that all the factors of development, exploration, and geology are being considered in the present examination and report for each individual mine and prospect, whereas the previous reports covered only the immediate development factors surrounding each mill group then in active operation or projected for operation at some early date in accordance with the possible needs for war production."

Aug 1, 1946

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

By S. B. Levin

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. During the fall of 1942, the Bureau of Mines put down nine diamond-drill holes at the Cape Rosier zinc-copper-lead mine in Hancock County, Maine, that aggregated 2,883 feet of bore. These holes supplemented 13 holes, aggregating. 5,501 feet, put down on the property about 2 years earlier by the St. Joseph Lead Co. Veins of mixed sulfides were intersected in 15 of the holes drilled. Beneficiation tests were made on samples of ore obtained from old dumps. Zinc-copper-lead sulfides occur at the Cape Rosier mine as lenses in a zone of altered agglomerate beneath and between a series of diorite sills. The mineralized zone strikes F. 17° E. and dips southeast. Between July 1881 and September 1883 the mine produced about 10,000 tons of ore reported to have contained 20 percent zinc, 2.8 percent copper, and some lead. The crude ore was hand-sorted, and some. 3,000 tons were reported shipped.

Jan 1, 1948

By John H. Soulé

"INTRODUCTION The Mining Branch of the Bureau of Mines has used the wagon drill to sample mineral deposits in New Mexico. This method of sampling was successful and con¬stituted an important phase of the work on five exploratory projects undertaken in 1943, 1944, and 1945. The deposits varied in topographic features, geology, mineral content, and in the physical characteristics of the rocks drilled. The altitudes ranged from 630 to 7,800 feet. Three hundred and seventeen holes totaling 6,852 feet were drilled. The deepest hole was 66 feet; the average depth was a little less than 22 feet.The results of the above-mentioned work form the basis of this report. Special attention is given to the later and more improved techniques used. This report was written with the expectation that the procedures might prove advantageous to others in the exploration and sampling of near-surface mineral de¬posits, and that a more extended use of the technique might result.AcknowledgmentsAcknowledgment is due Charles H. Johnson, chief of the Rolla Division, Mining Branch, for helpful suggestions in starting this work, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, W. R. Storms, engineer-in-charge of the Silver City, N. Mex., Field Office, and Donald H. Mullen, mining engineer attached to that office, for assistance in preparing and editing this report."

May 1, 1947

By John B. Umhau

[This !m-i~!.al survey giver, statistice.1 data res;?~dirf ~:rimay ard ?eco~- dqr or scmn tin used in thL: United St,ztas by industries an? incluclcz d;ta on stop&apos;ics, ~urchares, ard plnrt losr.c.5. It is :i ml:anwe of consq~tion in terms of fir.is1icd -prcd.~cts nz6.e iry initid ti11 Sabric:,.torc,, that is, aon- cerns that purchzse virc,in zni s~col~d&apos;l~y i.i.5 ti:; 01&apos; tin c;cra.. rav materi,als ar,d co:lrrert them into !ror?ucts such F!: ti:i plz.te, ~lloyr;, and. c?hemic?ls; comy~nias ;~urchn.&apos;.ii~; alloys, ch:rr.ic,~l::, or tin vl?.tc fcr furthcr a:mflzc- ture ?rc: ~-.f>t i~ci~~dcd. Tilit r~lqe:;tionrr::ire submit tod to consunern ar,nt:incd no dofinition of rnr.oncl.:ryr me$.-i; but, ovrirq to ti~i-: a~counti~ procedure used s.l~o~c-:t 1&apos; thu scrnn hac i~-.rtergol:e ch?rri?~ of ovinerzhip or titlo, thc rc!coverod t! n !its b~en i-c<;,r(it.!rj L.S r,e~3r;d:q met.1. Tbv tin content ~f ]

Jan 1, 1938

By J. B. Zink

The Bureau of Mines developed a spectrochemical method to determine six constituents in coal ash in the following concentration ranges: silica 9 to 63 percent, alumina 7.5 to 35 percent, ferric oxide 2 to 30 percent, calcium oxide 1 to 29 percent, magnesium oxide 0.5 to 6 percent, and titanium oxide 0.5 to 4 percent. Samples of coal ash are fused with a mixture of lithium tetraborate and vanadium pentoxide. The resulting beads are crushed, mixed with powdered graphite, and briquetted. The pellets are analyzed spectrographically, using controlled high-voltage spark excitation. Vanadium serves as the internal standard. Effects due to matrix variations are minimized by fusion with lithium tetraborate. Intensity ratios of selected analytical lines are determined photometrically, Concentrations are read from analytical curves, prepared from synthetic standards, relating log intensity ratios to log concentration. A combustion procedure is used to determine sulfur tri-oxide. The method is most useful when large numbers of coal ashes must be analyzed but a high degree of accuracy is not essential.

Jan 1, 1967

By B. P. Martinez

In response to a request from the President, the Department of the Interior joined with other agencies in a comprehensive study of the land and water resources of the New England-New York region. As part of this study, chemical engineers of the Bureau of Mines have visited 1,025 mineral-industries plants to inventory the waterborne wastes of mineral origin, discharged by the mineral industries of the New England-New York region. Four-hundred and sixty-two of these plants disposed their wastes to a public sewer of some type, but waste control remains a problem for moat of them. The 1,025 plants are discussed in main industry groups according to their production: Chemical and allied products. Stone, clay, and glass products. Iron and steel and their products (except machinery). Nonferrous metals and their products. Electrical machinery. Machinery (except electrical). Transportation equipment. Miscellaneous mineral industries.

Jan 1, 1956

By W. C. Holliman

This report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, and 10 grade 115/145 aviation fuels.

Jan 1, 1948

By Rolland L. Blake

The Bureau of Mines is concerned with extracting minerals from residual geothermal brines after their heat content and some demineralized water have been recovered. This literature study is based on a survey of the literature and discussions with individuals knowledgeable on various aspects of the subject. This report examines the potential of the domestic geothermal mineral resources, considers the technical problems involved, and outlines possible effects on the environment from reservoir fluid withdrawal and reinjection. Geothermal resources in the Western United States were extensively explored during the 1960&apos;s. Limited development operations included exploratory drilling and operating wells producing hot brine, separating steam for experimental electric power generation, and recovering minerals in solar evaporation ponds or in extraction plants. Interest in the recovery of minerals and salts from geothermal fluids waned because of corrosion and scaling problems and low or no market value of the mineral products. Most of these problems can be controlled with existing technology and careful planning of processes and equipment. Extracting geothermal minerals is technically feasible, but the problems of low or no market value for major mineral products, and insufficient amounts of more valuably major products, make mineral recovery uneconomical at present.

Jan 1, 1974

By Paul M. Tyler

A great variety of substance that differ widely in chemical, mineralogical, and physical properties are loosely linked under the generic term "clay", but for the average man all that matters is whether a given material can be sold or used profitably. So-called "clays" range in texture from true clays and allied minerals that are typically "fat" or sticky to fine sand. Sand and other strictly silicious materials, such as tripoli and diatomite, are not clays in any sense; but many commercial clays are strictly loams, for they are intermediate in texture and always contain a mixture of minerals, though the term "loam" has little commercial usage except in foundry work. Even pure kaolinite, ordinarily considered the typical "clay substance", recently was found to exist as three distinct minerals; and each of these, in turn, exhibits variations in particle size and other physical attributes. Probing with the X-ray and employing other modern tools and techniques, scientists are tracing the patterns of molecules and finding chemical and physical phenomena that seem to disclose the causes for the markedly different behavior of the various aluminum silicates with varying proportions of combined and adsorbed water that are the essential ingredients of commercial clays; but rule-of-thumb definitions and enforced reliance upon empirical tests of actual samples still hold sway. In addition to the hydrated simple silicates of aluminum, almost all clays contain quartz, feldspar, and mica with varying amounts of organic matter and, in addition, other impurities - such as iron, manganese, and titanium oxides - that may discolor them sufficiently to render them unfit for certain important uses. The white clays are generally the purest, but no two clays are really alike, and great care must be exercised to maintain a reasonable uniformity in successive shipments even from the same deposit.

Jan 1, 1938

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

By Harold E. Marr

Energy dispersion X-ray analysis was evaluated for possible application in the secondary metals industries for the rapid analysis and identification of copper-base alloys. Laboratory investigations of standard brass and bronze samples indicate that X-ray methods are capable of separating standard alloys into 10 general classes with analytical times of less than 3 seconds per sample for clean, flat samples. A radioactive source of americium 241 with a secondary fluorescer was used as an excitation source, and a lithium-drifted silicon semiconductor detector was utilized for energy discrimination of X-rays.

Jan 1, 1974

By Roy L. Grant

The Bureau of Mines investigated the up-and-down method with factorial designs to determine if shorter, and therefore less costly, trial sequences could be used. Although sequences of 50 trials are usually recommended, sequences of 20 trials were arbitrarily chosen for the experiments with permissible coal mine explosives described in this report. These explosives were fired from a cannon pointed into a flammable natural gas-air atmosphere at the Bureau of Mines Explosives Research Center gallery to ascertain their safety properties. The investigation demonstrated that the shorter sequences led to useful conclusions with a reduction in cost of the experimental program.

Jan 1, 1967

By E. C. Lane

This report presents the results of the Bureau of Mines&apos; twenty-first semiannual survey of motor gasoline marketed in the United States. The 12 cities in which samples were collected have teen chosen as representative of the more important marketing territories, as it is obviously impractical to obtain a sample of every gasoline sold in the entire country. The survey reveals that the motor gasoline which is being marketed in the United States this winter is decidedly more volatile than that sold a year ago. Samples from all cities show a decided improvement in volatility except those from Laramie, Wyo., which show a small decrease in volatility.

Jan 1, 1930

By R. H. Sprute

Underground accumulations of slimes in the Henderson mine are routed to two large collection pits where they are dewatered and consolidated by application of direct current. Densified material is then removed to ore cars by rubber-tired front-end loaders and transported out of the mine. This Bureau of Mines report describes the electrical dewatering installation and compares its efficiency of operation with that predicted from preliminary laboratory studies performed by the Bureau. Direct current from a 150-kw rectifier (applied for 44 hours at 400 amperes and 65 to 70 volts) converted slimes containing 25.3 percent solids to material ranging from 44 to 65 percent solids. Better results can be expected if the ramp and front sections of the pits are treated separately, using higher current density.

Jan 1, 1980

By M. J. Kovalik

Lower Sunnyside seam coal from Utah was blended with various proportions of char and high-temperature coke to improve the quality of the coke obtained from carbonizing this coal. The Hanson 5-pound carbonizer was used as a "screening test" for the larger scale Bureau of Mines-American Gas Association (BM-AGA) tests, which were correlated with industrial production. Eighteen carbonization tests were made in the BM-AGA 13-inch retort, with a coal charge of about 90 pounds; the cokes were evaluated by the standard ASTM tumbler test. Carbonization of blends containing char and coke breeze yielded less fissured and blockier cokes of significantly higher ASTM I-inch tumbler indices as compared with the value for the straight Sunnyside coal. It was found that the simultaneous addition of char and coke breeze yielded stronger cokes than that obtained by the addition of either one of these additives. Addition of a small proportion of Pocahontas No. 3 or Sewell coal to an optimum blend improved the resulting coke strength further.

Jan 1, 1969