Search Documents

By W. H. Coghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By S. J. Gasior

Pilot plant studies showed the technical feasibility of fluidized-bed operation for producing hydrogen and synthesis gas by the steam-iron process. A mixture of iron and iron oxide from 20-to 100-mesh was partially reduced with a simulated producer gas and then oxidized with steam and/or carbon dioxide. Results of tests show the effects of pressure, temperature, bed height, gas-to-solids ratio, type of iron oxide, and composition of gas on the gas and solids conversions during reduction and oxidation. A baffled free-fall solids system was also found operable. The short residence time of about 5 seconds limited conversion of the solids.

Jan 1, 1961

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average e B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig, 1).]

Jan 1, 1941

By Leo J. Neill, O&apos

Abrasives are essential to the manufacture of munitions - airplanes, gas, shells, tanks, and in fact every product that involves metal forming or finishing. An indication of the importance of abrasives in the national defense and aid-to-Britain programs is the close peace-time correlation between demand for abrasives and automobile production, which in recent years has consumed more than 35 percent of the total output of abrasives. Unprecedented demands on the abrasives industry are forecast by the rapid expansion in airplane output, tie increased mechanization of all armed forces, and the consequent speeding up not only of the factories where finished munitions are made but also of the steel mills and other factories were additional large quantities of abrasives are needed for snagging or rough-grinding semifinished products before they can be used by the fabricators. A recent survey by the artificial abrasives manufacturers indicates that they can readily increase their output 75 percent compared with the previous peak of 1937 without building new plants. By overhauling production schedules, their maximum production possible could be increased to 182 percent of the 1937 output, and the nature of the industry is such that plant capacity could be increased rapidly if need therefor should arise. No figures on the estimated requirements for abrasives in 1941 or 1942 have as yet been compiled, but the industry feels that it can meet demands as they develop.

Jan 1, 1941

By H. Kenworthy

The objective of this investigation was to evaluate the technical feasibility of smelting certain low-grade domestic iron ores in an electric furnace. Laboratory-scale experiments showed that a high recovery of iron in the form of pig iron can be obtained from east Texas ores containing less than 25 percent iron. The pig iron was amenable to standard-or electric-furnace-refining methods for producing steel. Car-bon, silicon, and phosphorus were the primary impurities removed in refining. Overall recoveries of iron as pig iron exceeded 95 percent, in contrast with commercial mineral-dressing recoveries on these particular ores of 50 percent of the iron as a 45-to 50-percent iron concentrate.

Jan 1, 1958

By William C. Cooley

This volume contains copies of the 5 x 8 in. accession card file for all items collected which were judged to be relevant to underground hydraulic coal mining. In many cases, abstracts are included. Abstracts were taken from the source, from other reviews, or from the preliminary screening of Russian documents performed by Dr. A. L. Brichant. No attempt was made to write abstracts for every accession item.

Jan 1, 1975

By Jerry A. Wichser

A series of linear programmed instruction modules was developed in the general subject areas of Blasting Technology & Explosives Safety & Electrical Training. The linear programs (modules) were developed in the form of tape-slide plus workbook materials, while the branching format evolved from the LTS teaching machine system from MIT, through several other teaching machines and micro-computers, finally settling on Radio Shack TRS-80 microcomputers, Models I & III. Initial validation figures indicate that essentially the same result, are attained from both methods (based on pre and post test scores), with the most noticeable difference being an approximately 25% savings in study time with the branching modules. In December 1980, the development of modules on High-Voltage Training, Trolley Wireman Training, and Compressed Gas Safety was added to the overall tasks of the contract.

Jan 1, 1984

By Phillip N. Yasnowsky

This Bureau of Mines report summarizes State severance taxes imposed on minerals and mineral fuels, provides a hypothetical example of how a State severance tax affects selected components of a firm's income statement, and uses the Bureau's Minerals Availability System (MAS) to estimate the effect of assumed changes in State severance tax rates on copper recovery cost at given levels of potential copper availability. A reduction of the rates to zero or a doubling of them results in changes in costs that are of the same order of magnitude as the cost of transporting copper to the United States from major foreign producing countries.

Jan 1, 1982

By A. J. Farstad, R. G. Olsen

The Coal Mine Health and Safety Act of 1969, passed by Congress in the wake of the disaster at Farmington, West Virginia, led to an extensive study by the National Academy of Engineering of the problems involved in coal mine safety. One of the results of this report and subsequent research conducted by the U. S. Bureau of Mines has been the investigation of electromagnetic techniques for the location of trapped miners after a mine emergency. The Westinghouse Georesearch Laboratory has been involved in both the 2 theoretical and field studies relating to this problem. A compact personal beacon transmitter has been developed which can be attached to and powered by a miner's lamp battery. A compatible lightweight loop antenna package has also been developed which can be easily carried on a miner's belt. This antenna can be quickly deployed on the mine tunnel floor. For the purpose of calculating its electromagnetic fields on the earth's surface, the loop can be considered to be a magnetic dipole buried in the earth. (The earth is assumed to be homogeneous and to have a conductivity of s mhos/m.) The surface of the earth is assumed to be uniformily sloping and the transmitter dipole oriented as in Figure 1. The fields on the earth's surface can be computed by using a superposition of the fields of a 4 vertical magnetic dipole3 and of a horizontal magnetic dipole in proportions which depend on the slope of the terrain. In the case of level terrain a null in the horizontal magnetic 5 field occurs on the surface directly above the dipole. This null is designated as the apparent source location and is the criterion by which the source is located. The criterion was tested at two hardrock mines and two coal mines in the fall of 1972. The apparent source locations were compared to actual locations determined by conventional surveying techniques. It was found that due to nonlevel terrain the apparent and actual source locations differed by up to 13 meters. This discrepancy can be resolved by an examination of the fields of a source beneath uniformly sloping terrain. Figure 2 shows the experimental and theoretical results for a

Jan 1, 1973

By E. Morrice, R. D. Smith

Thermal expansion and electrical resistance measurements were made on cerium metal from 4° to 300° K. The apparatus developed , including a specimen holder and a cryostat system , are described along with the experimental techniques used in obtaining the measurements . The total linear thermal expansion Data at of 99.83 weight - percent cerium metal between 4 ° K and room temperature was 4.24 percent . The resistivity at 4° K was 7.0 x 10-6 ohm- centimeter . 4° K indicate a fundamental relationship between residual resistivity and purity of cerium metal . The effects of annealing and repeated thermal cycling on resistivity were determined .

Jan 1, 1964

By R. V. Ramani, R. Bhaskar

"The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.IntroductionAn airborne dust cloud is a complex system containing particles of varied size, density, shape and state of aggregation. The behavior of the particles is dependent on a number of complex physical mechanisms, often opposing in nature. The net interaction results in the ambient concentration. This size dependent behavior of particles contrasts with that of gases, an area quite widely studied.The term aerosol is used to describe clouds of microscopic and submicroscopic particles in air such as chemical smoke or particulate matter released from smoke stacks. An aerosol system can be regarded as an arbitrary element of volume filled with gas and suspended particles of possible highly variable physiochemical nature. The parameters that are used to describe an aerosol system include concentration, mass average velocity and particle mass and radius. In characterizing such systems, several assumptions are made. Among these is the assumption that particles are smooth, inert and rigid spheres. Again, for example, when the particles are in transport, the possibility of collision exists. As a result of the collision, the particles may coalesce to form larger particles. The probability of sticking is considered a known quantity (lady, 1970). In this paper, the application of the principles used in aerosol systems is explored for the study of the transport and deposition of fine coal dust in underground mines."

Jun 1, 1988

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0.5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that quenched slags can be treated at slightly lower cost than slow-cooled slags. However, the cost advantage of processing quenched slags is more than offset by the higher copper recoveries obtained from slow-cooled slags.

Jan 1, 1971

By W. J. Fene, R. D. Currie

The value of protective clothing in the prevention of injuries has long been recognized in many of the leading industries , but the adoption of the idea into mine safety programs is comparatively new . Once started , however , the idea has grown rapidly and the results already obtained by mining companies have shown that it is fundamentally sound . Both coal and metal mining companies are rapidly adopting these protective measures , and since 1924 many mines have become well equipped with eye , head , and foot protection . At the present time approximately 70 percent of the employees in the anthracite mines of Pennsylvania are provided with safety hats . At many metal mines all employees are provided with safety hats, shoes , and goggles . The Pennsylvania mining law provides that all shaft · workers in anthracite mines shall wear protective hats . In According to a study³ made of the nature of 3,485 temporary injuries and of the parts of the body of underground coal mine employees most exposed to occupational hazards , the head and face were injured 665 times , the hands 856 times , and the feet 565 times . Of 2,555 temporary injuries in metal mines , the head and face received 484 , the hands 788 , and the feet 357 . a similar study4 made by a coal -mining company for the year 1928 , of 556 injuries the scalp received 9 , the skull. 4 , the eyes 47 , the hands 62 , the thumbs 21 , the fingers 141 , the ankle , the feet 51 , and the toes 35 . Probably most of these injuries could have been prevented by suitable protective clothing and equipment . This study also revealed that at least one injury occurred

Jun 1, 1933

By Paul M. Tyler

[This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining laws of specified French possessions in Africa has been prepared from the best information available in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it is being referred through the courtesy of the Department of State. France controls large areas on the African continent, but the various Colonies and Dependencies are administered more or less independently. Algeria is under the direct jurisdiction of the Ministry of the Interior, and its mining laws are essentially the same as those of the mother country. Tunis and Morocco are attached to the Ministry of Foreign Affairs; separate digests of the mining laws' of these respective colonies have already been prepared by the United States Bureau of Mines. The present paper covers all other French territory on the continent of Africa except Somaliland, a rather small Colony including the port of Djibouti near the point where the Red Sea joins the Gulf of Aden. Available information indicates that the prospects of mineral production in this Colony, apart from salt and gypsum, are not at all encouraging.3]

Jan 1, 1933

By John C. Edwards

The U.S. Bureau of Mines has constructed a smoke chamber and developed sensitivity tests for smoke detectors. Response of ionization-and optical-type commercially available smoke detectors have been investigated. Six smoke detectors were measured with respect to visually obscuring smoke characterized by a corresponding optical density for smoldering and flaming coal combustion in the smoke chamber. It was determined that for one type of ionization smoke detector the alarm time was nearly equivalent to that of an odor monitor's alarm for smoldering coal combustion experiments and earlier for flaming coal combustion experiments. The experiments showed that an average CO concentration of 5 ppm corresponded to an optical density of 0.022 m-l for smoldering and flaming coal combustion. Two of the commercially available ionization-type smoke detectors were more responsive to flaming than smoldering coal combustion at an optical density of 0.022 m-l, whereas the optical smoke detectors showed the opposite trend. The responsive characteristics of the detectors evaluated with respect to known smoke conditions in the smoke chamber shows their potential for use as mine fire sensors or part of a mine atmospheric monitoring system to improve mine safety.

Jan 1, 2010

By William Cochran

The Bureau of Mines investigated mine subsidence caused by recent underground mining, estimated the extent of damages, and formulated a procedure for evaluating subsidence costs. On the basis of the quantity of material removed from beneath the surface, bituminous coal mining currently causes more extensive subsidence problems than mining of other minerals; costs are highest in areas such as western Pennsylvania where urban and suburban development and related types of land use conflict with mineral recovery. The Bureau of Mines estimated subsidence costs, including surface damages and control costs, for a 12-county area in western Pennsylvania for 1968. Total surface damages attributable to the underground production of bituminous coal in the 1-year period were $295,000; in addition, 12.4 million tons of coal, valued at $4.3 million, was left in place to minimize potential surface damage. Of the total subsidence cost ($4.6 million), $2.7 million was classified as external or social costs, not reflected in the market value of bituminous coal; this averaged $0.05 per ton of production, or slightly less than 1 percent of the market value.

Jan 1, 1971

By G. M. Potter, S. J. Hussey, R. Havens

The Artillery Peak manganese ores , from one of the largest known manganese deposits in the United States , present a difficult problem in concentration because they are low-grade and the association of manganese and gangue minerals is intimate and complex. The known size of this deposit has justified investigation of processes such as leaching, wherein preliminary enrichment of the original feed might be advantageous .. Therefore , the ore-dressing studies on Artillery Peak ores were carried on with the object not only of making directly marketable manganese products but also of removing acid-consuming calcite and raising the grade of ore for leachingplant feed . Owing to the extent of the deposits , test work was carried on at the Salt Lake laboratories in considerable detail on several lots of ore of varying composition . This paper summarizes the results obtained from laboratory testing of four samples obtained by engineers of the Mining Branch from the Maggie Canyon area of the Artillery Peak deposit . Also included are results obtained from testing one sample of Chapin Group ore , which was considered representative of numerous very low-grade ores submitted from the Artillery Peak district . During the course of the investigations , many data were obtained and compiled , but for the sake of brevity , data of secondary importance have been omitted or condensed and only those tests giving the more pertinent results are discussed in detail ...

Nov 1, 1947

As part of a continuing program of evaluating the Nation's crude-oil resource, this report presents information pertaining to resource, primary reserve, and potential waterflood reserve for 3,209 selected reservoirs contained in 24 oil-producing States, as of January 1, 1968. To that date the selected reservoirs had not been subjected to pressure-maintenance or secondary-recovery operations. These reservoirs also met the following parameters: (1) a minimum of five oil-producing wells on January 1, 1968, (2) a minimum of 50 acres areal extent, (3) a minimum of 50,000 bbl of oil ultimate primary recovery, and (4) the principal reservoir energy was other than active water encroachment. The selected 3,209 reservoirs produced 527 million bbl of oil in 1967, about 17 pct of U.S, total production. Primary oil reserve was 4,983 million stb; in addition, there was 6,043 million stb of potential water- flood oil reserve. Oil resource in the selected reservoirs was 59,547 million stb. A brief history and outlook of waterflooding are presented for each State. Depth and producing rate statistics and geologic distributions of production, resource, reserve, and potential waterflood reserve for the selected reservoirs are presented by States in the appendix. Also included in the appendix are description, history, and technique modifications of waterflooding, and a preliminary cost estimate of a closed-system water-injection project.

Jan 1, 1970

By Sidney Katell

This study presents the economics of the hot-carbonate purification process for removing C02. It considers three variations of the process in order to meet the design specifications, which call for a feed-gas flow of 10 million standard cubic feet per hour (std.c.f.h.) with C02 inlet concentrations of 10, 20, and 30 percent and exit C02 values of 5, 2, 1, 0.5, and 0.1 percent. Inlet pressure and temperature are 350 pounds per square inch [e] (p.s.i.g.) and 300° F., respectively. Estimated capital and operating costs are shown in the following to tabulations: [ ]

Jan 1, 1960

By John Nagy

The Bureau of Mines adapted thermal theories explaining combustion of gases to correlate parameters affecting ignition of dust dispersions. The dust dispersions were ignited in a Godbert-Greenwald furnace at atmospheric pressure. Ignition temperature and the concentrations of fuel, admixed inert powder, and atmospheric oxygen were related mathematically. Values for these parameters obtained in laboratory experiments for cornstarch agreed with theory. The developed equation permits extrapolation; the predicted upper igni-tion limits correspond with limited experimental data from laboratory and large-scale tests. Explanation of the effect of fineness of dust on ignition parameters is attempted by introducing a surface-area constant to modify the activation energy. Arguments are presented to show that the ignition process is a solid-gas phase reaction rather than an ignition of prevolatilized gases.

Jan 1, 1966