Search Documents

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the SrF2-Y2O3 system for which liquidus and solidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. The phase diagram was constructed from information obtained by ceramogra¬phy, X-ray diffraction, thermal analysis, and electron probe microanalysis of small specimens encapsulated in platinum-20 percent rhodium or molybdenum ampoules. The data indicate a simple eutectic system with limited terminal solid solubilities. The eutectic temperature is 1,457°±5° C, and the eutectic composition is 4±1 mole-pct Y203. Strontium fluoride containing up to 2 wt-pct 0 2 was studied to determine the effects of oxygen contamination. Oxygen levels in excess of 0.2 wt-pct resulted in eutectic formation between SrF2 and SrO. The eutectic composition is between 0.2 and 0.7 wt-pct 02, and the eutectic temperature is 1,447°±5° C. No intermediate oxyfluoride phases were detected.

Jan 1, 1974

By Eldon K. Stanek

The material presented in this chapter is a review of the work done during the period from June 23, 1972 to June 22, 1973 which was reported in detail in the first annual report for Grant No. 60122088 which was submitted on June 29, 1973. This report has appeared in the National Technical Information Service as bulletin number PB230 972/AS. 1.2 ANALYTICAL PREDICTIONS OF INDUCED VOLTAGES AND CURRENTS The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable, although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available from either handbooks or the manufacturer's published data. Thus, it is useful to present the results of the derivation of the inductance matrix and a few intermediate steps.

Jan 1, 1975

By Seth T. Reese

THE INJURY DATA and experience at coal mines in the United States for 1951 are presented in this bulletin under the following general heads: (A) General injury experience: Tables 1 to 18: Contain current data on number of fatalities and nonfatal injuries, frequency and severity rates, average severity, major and detailed injury agencies, and distribution of injuries by part of body and days of disability. (B) Selected injury data: Tables 19 to 43: Contain current data on various selected factors of operating and physical conditions that contributed to the occurrence of injuries at bituminous-coal, lignite, and anthracite mines. These factors include extent of hand and machine loading, size of mine by employment and production groups, thickness of bed or vein, duration and number of work shifts, rating of mine as gassy or nongassy, types of cap lamps, explosives, and combination of factors that influence mine safety. (C) Injury experience by States: Tables 44 to 50: Contain current data on number of fatalities and nonfatal injuries, frequency and severity rates, average severity, major causes and principal agencies, injury records of all coal-producing States, and the relative standing by States according to injury-frequency rates. (D) Major disasters: Table 51: Lists the coal-mine disasters that occurred during 1951, giving location, source, and cause. A major disaster in coal mining is defined as a single accident in which or as a result of which five or more men lost their lives. (E) Historical coal-mine injury experience: Tables 52 to 86: Contain data on injuries, injury-frequency rates, employment, and production at bituminous-coal, lignite, and anthracite mines from the earliest records through 1951.

Jan 1, 1955

By Erle C. Donaldson

Bureau of Mines engineers examined the chemical and biological treatment of sewage water designed in one case for reuse and in another for subsurface injection. In the first case discussed, approximately 6 million gallons per day of sewage are treated by the activated sludge process followed by tertiary treatment that includes ion exchange. The renovated water is used in the industrial complex. Liquid industrial waste is sent to a waste disposal facility where it is treated for injection into a deep subsurface formation. In the second case, a community of 3,000 people is using a lagoon sewage treatment system followed by subsurface injection of t- treated effluent. Subsurface disposal is used to avoid growth of algae and weeds in a nearby lake to which the treated effluent was originally discharged. The renovation of municipal water for reuse provides a source of water for industries in a semiarid region and may also provide a source for domestic use in densely populated regions where domestic water requirements have priority over industry needs. In addition both waste treatment systems provide examples of the use of subsurface waste disposal to avoid pollution of surface streams.

Jan 1, 1971

By Harold P. Rue

The problem of removing hydrogen sulphide from natural gas has become within the last few years one of major importance to the natural gas and petroleum industry. Several gas fields in the United States produce natural gas containing hydrogen sulphide, and a number of oil fields produce gas which contains hydrogen sulphide. 3 The percentage of hydrogen sulphide in natural gas produced in these fields varies from a fraction of 1 per cent to as high as 20.5 per cent by volume. Hydrogen sulphide is probably the most toxic gas associated with natural gas, and from the standpoint of health and safety it is important that the hydrogen sulphide be removed if the gas is to be used for domestic purposes. Hydrogen sulphide, besides being toxic and therefore a hazard to animal life, is under certain conditions an active corrosive agent and very destructive to equipment. The annual loss caused by the corrosive action of hydrogen sulphide on equipment amounts to hundreds of thousands, perhaps millions, of dollars. The largest percentage of natural gas produced in the United States comes from wells which also produce oil. This associated gas invariably carries with it light fractions of petroleum, which when separated from the gas, condense to the liquid form at ordinary temperatures and pressure. Commercial application is made of this natural condition, and "wet gas" is processed to obtain so-called natural gasoline by employing the principles of absorption, adsorption, or compression and subsequent expansion accompanied by cooling. In the manufacture of natural gasoline from wet gas which contains hydrogen sulphj.de, if this contaminating gas is not first removed, some of the hydrogen sulphide may oxidize to form free sulphur and water. The free sulphur will dissolve in the gasoline produced by any of the aforementioned methods and cause the product to be positive to the corrosion test and there-fore unsuitable for commercial use in that condition. The objectionable sulphur compounds can be removed by washing the gasoline with a solution of caustic soda or other chemicals, but this treatment is expensive. It is advantageous therefore to remove the hydrogen sulphide from the gas before it is processed in a natural-gasoline plant.

Jan 1, 1932

By J. B. Gayle

Many investigators have reported studies of size distributions for particulate solids ; usually , these have involved the fitting of size distribution data to a particular mathematical function . Such studies are of unquestioned value and have contributed much worthwhile information regarding the breakage mechanisms for a variety of brittle materials . In connection with a Bureau of Mines study of the size distribution of coke , which has been subjected to the standard American Society for Testing Materials (ASTM) tumbler test , attention was focused on the relation between the 1 -inch tumbler index (usually considered to be indicative of the ability of coke to resist degradation by impact ) and the 1 /4 - inch tumbler index ( indicative of the ability to resist degradation by abrasion ) . Specifically , it was noted that for certain sets of data the correlation coefficients denoting the relation between these indexes were positive ; for other sets of data , these coefficients were negative . Preliminary consideration of this problem indicated that the usual interpretation placed on correlation coefficients was erroneous in this particular instance because the variables being correlated were necessarily related . The work described in this report was undertaken to clarify the interpretation of results of correlation studies for variables of this type .

Jul 1, 1960

By R. W. Huber

Three arc-melted ingots, two of a titanium-7 percent manganese alloy and the third of unalloyed titanium, were forged and rolled into 3/4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties. These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots. INTRODUCTION Arc-melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Park, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.

Jan 1, 1955

By R. S. Dean

The development of metallurgical processes may be divided into periods : First , the discovery of a basic reaction which brings about the production of the desired product from the available raw material ; second , a long stage of mechanical development during which little or no attention is paid to the reaction itself ; and third , a careful study of the reaction . Most metallurgical processes are to -day approaching the end of the second period . This we may illustrate by the steel process . The reaction of carbon with iron ore to produce pig iron and the subsequent refinement of the pig iron by an oxidation reaction is very old . Development in modern times has been almost entirely mechanical , the development of the blast furnace , furnace , the Bessemer process , the Siemens process , and even the Aston process for wrought iron being mechanical improvements almost entirely . Metallurgy is now entering a phase where the reactions are being considered . The question of how far can they be made to proceed is being repeatedly asked . As mechanical processes are improved , we approach a limit to which our basic reactions can be pushed which is determined by the nature of the reactions themselves . We want to know : How far can iron be decarbonized by iron oxide ? How low can the oxygen of copper be reduced by any given reaction? How efficiently can the fuel in a zinc reduction process be used ? The demand for purer metals and lower production costs has forced these and similar questions upon us . How are we to answer them ? The determination of these equilibria or end points of metallurgical reactions by direct means is fraught with difficulty because here we must overcome mechanical difficulties which too often become the limiting factors even in the laboratory and we do nottherefore get the actual limit to which the reaction itself may be carried . Further , there are so many reactions of metallurgical materials that to survey each separately is a job to give pause to any experimenter or group of experimenters .

Dec 1, 1930

By H. D. Hess

This report describes in detail a unique occurrence of fersmite, (Ca, Ce, Na) (Cb, Ti, Fe, Al)2 (0, OH, F)6, which occurs as small anhedral inclusions and intergrowths with a tantalum-free columbite found in the metamorphic complexes of Ravalli County, Mont. Chemical and crystallographic data along with the physical and optical properties agree in general with those given in the original description of fersmite from the Ural Mountains of Russia. X-ray diffraction data not given in the original description and more specific optical data have been determined. The Montana fersmite, now established as the second occurrence of this rare calcium-columbate mineral, was discovered during a routine Bureau of Mines mineralogical examination of a prospector's sample.

Jan 1, 1960

By L. D. Schmidt

Now that the war is over, there is a great revival in popular demand to decrease pollution of the atmosphere in our cities. Great cities, such as Pittsburgh, are starting to enforce laws against violators of smoke ordinances. The substitution of low-temperature coke for bituminous coal in household heating is a most promising field for helping to eliminate the smoke nuisance. This Information Circular is written to assist in the very worth-while effort to reduce atmospheric pollution. Herein are de- scribed recent German developments in the production of low-temperature coke. Operating and cost data are given on German commercial-scale low- temperature carbonization plants.

Feb 1, 1947

By J. R. Ross

The extraction and recovery of nitrate from waste solutions generated in the production of titanium were investigated using solvent extraction techniques. Laboratory studies and continuous tests in a small solvent-extraction system showed that up to 98 percent of the nitrate can be selectively extracted by a solution of tributyl phosphate in kerosine. The extracted nitrate can be recovered as nitric acid, at concentrations suitable for reuse, by stripping the loaded organic with water.

Jan 1, 1973

By S. J. Broderick

[The discovery in 1934 that carbonaceous materials, such as coal, peat, and lignite, when treated with concentrated sulfuric acid, were given cation or bate-exchange properties opened up a field of new materials with many interesting possibilities. These hydrogen exchangers, as they were called, were so superior to the impractical hydrogen exchangers made from natural and synthetic zeolites tat they were accepted immediately by the water-conditioning industry. A noteworthy advantage of the carbonaceous exchangers is that they are nonsiliceous, hence they do not give up silica to the water as do the natural and synthetic Zeolites, especially if the hard water is corrosive. For this reason the new exchangers found immediate favor in boiler-feed-water conditioning.]

Jan 1, 1941

By J. G. Walters

This bulletin presents, in collected and tabluated form, Bureau of Mines and American Gas Association (EM-AGA) carbonization data pertaining to the chemical analysis of tars and the characterization of tars and light oils obtained from U.S. coals.

Jan 1, 1967

By S. J. Broderick

[The discovery in 1934 that carbonaceous materials, such as coal, peat, and lignite, when treated with concentrated sulfuric acid, were given cation or bate-exchange properties opened up a field of new materials with many interesting possibilities. These hydrogen exchangers, as they were called, were so superior to the impractical hydrogen exchangers made from natural and synthetic zeolites tat they were accepted immediately by the water-conditioning industry. A noteworthy advantage of the carbonaceous exchangers is that they are nonsiliceous, hence they do not give up silica to the water as do the natural and synthetic zeolites, especially if the hard water is corrosive. For this reason the new exchangers found immediate favor in boiler-feed-water conditioning.]

Jan 1, 1941

By J. A. Eisele

The Bureau of Mines has reviewed the literature related to the recovery of A1203 (alumina) from coal ash. A small amount of unpublished data is also reported. Of the processes studied, the alkaline-sinter process is the most promising from a technical standpoint. However, owing to the high cost of processing coal ash, the dispersed location of powerplants, and the domestic availability of higher grade alternate materials, coal ash does not rank as a primary source material for replacing imported bauxite.

Jan 1, 1979

USBM Contract H0133045 consists of the design, build and test of 50 waveform generators. The waveform generator is a small ULF transmitter operating in the 1 to 3 KHz frequency range for the purpose of locating trapped miners during a mine disaster. This contract provided for the design, test, and building of 50 waveform generators using a discrete component construction with an option of using hybrid construction techniques within 105 days after the effective date of the contract. Because of large quantity economic considerations, this option was not initiated. Two engineering models were designed, constructed and tested and 50 final production units were fabricated using discrete construction. Complete documentation is supplied under a separate package which includes final schematics, parts list, layout information, equipment specification, production test procedures and qualification test procedures. Ten units have been delivered to the USBM. The remaining 40 units are being retained for packaging under contract H0242010 Transmitter Package and Receivers.

Jan 1, 1974

By Otto Ruhl

The Oronogo-Webb City-Duenweg district is in the northeastern part of the Tri-State zinc and, lead field. Its metal-mining history dates from the early 1850's. For some years prior to 1918 it ranked as the leading producing area of the entire Tri-State field, but by 1920 most of its mines had been abandoned and allowed to fill with water. Its mine operators had-been attracted, to the newly discovered and richer deposits around Picher, Okla. In 1943, the Orenogo Mutual Mining Co. was exploiting the Oronogo Circle deposit in the northern end of the district, and the Federal Mining & Smelting Co. was preparing to mine on its holdings in the southern part near Duenweg. The area between these two operating units ranked as the largest single block of ore reserves under water in the Tri-State field. In 1942, engineers of the Bureau of Mines, in collaboration with the William Stewart Engineering Co. of Joplin, collected all available mine maps, mine reports, and logs of old drill holes in the inundated area. From a careful study an appraisal of these data, the reserves in the block were calculated at 20,647,800 tons of ore containing 606,440 tons of 60-percent zinc concentrates and 46,970 tons of 80-percent lead concentrates. The ore was estimated to contain 1.76 percent recoverable zinc and 0.18 percent recoverable lead.

Jan 1, 1949

By Dayton C. Bolin

This paper is one of a series being prepared by the United States Bureau of Mines describing quarrying methods and costs at stone quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scrope of the cost tabulations shall ensue. ACKNOWLEDGMENT The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer, United States Bureau of Mines, in the preparation of this paper. Acknowledgment is also made to E. R. Lederer, vice president in charge of the company's operations, through whose kindness the preparation of this paper was made possible. E. T. Eubank, superintendent of the quarry, and J. A. Hodges, quarry foremen, gave much of their time to this work. The cost data were compiled by the company's chief clerk, J. von Carlowitz.

Jan 1, 1931

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered transportation equipment approved or certified by the Bureau of Mines f r use in gassy noncoal mines and tunnels. Testing of diesel-powered equipment is one phase of the Bureau's health and safety program of approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, and toxic hazards in underground mines. In mines such equipment must be used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study f their design and safety features. Equipment must pass exacting tests and meet strict requirements established through research, development, and experience before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1967

By Debra A. Griffith

The U.S. Bureau of Mines currently is researching the relationship between the level of back strength and the probability of low-back injury. This report is a review of the literature and statistics on over-exertion injuries. Overexertion continues to be a significant source of injury in metal and nonmetal mining, accounting for approximately 24 pct of all injuries yearly. These injuries, particularly to the lower back, can be very expensive in human and monetary terms. An examination of the accident data on overexertion injuries is necessary to provide a background for research into prevention and/or amelioration of those in-juries. The job categories outlined in the Accident Data Analysis data base most affected are "Mechanic/Electrician" and "Mill/Plant Worker." The age group most affected is "30-39" years, and the experience group most affected is "0-.99" years. The most prevalent type of overexertion injury is "Strain/Sprain," and the trunk is the body part most often involved in an overexertion injury.

Jan 1, 1994