Search Documents

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

All output is saved in the file MFIRE OUT m the di¬rectory and on the disk containing the program The file can be inspected with a text processor and sent to a print¬er, if needed CONTENTS OF OUTPUT FILE The comment lines, reference temperature, air densi¬ty, a table of the units of measure for the results, and the average values are shown at the beginning of MFIRE OUT All input data will be shown in the output file if LOUT on Control line number 1 is _<-1 For each contamination source, a new branch will automatically be setup The new airway and junction ID numbers will not interfere with the original numbering scheme of the data file Next are the results of the selected simulation(s) in the following order network balancing, network balancing considering temperatures, transient-state modeling, and altered equilibrium due to fire and distribution of the contaminants. Depending upon the contents of the data file, and the simulation selected, attention, warning, and error message will be shown at locations where calculations resulted in unusual conditions

Jan 1, 1990

By Christopher Mark, Anthony T. Iannacchione

Falls of ground continue to be one of the most serious causes of injury to U.S. miners. Of the 256 fatal injuries that occurred in mining between 1996 and 1998, 59 (23%) were caused by falls of ground (Table 23.1). Falls of ground affect some sectors of the mining industry more severely than others. For instance, nearly 40% of the 98 coal mine fatalities between 1996 and 1998 were caused by falls of ground. Underground miners are at much greater risk than surface miners. Nearly half (45 out of 101) of underground mine fatalities were attributed to roof, rib, and face falls, while only 6% of the 155 surface fatalities were caused by falls of highwalls or slopes. The goal of this chapter is to provide guidance to safety professionals tasked with preventing ground fall injuries. This chapter combines an analysis of the Mine Safety and Health Administration&apos;s (MS HA) accident and injury data with a survey of industry "best practices" to safeguard miners from ground falls. Ultimately, this approach can help to form the basis of a sound, proactive ground control program for the mining industry. SOURCES OF DATA All the injury data examined in this study were derived from MSHA&apos;s fatal investigation reports and the MSHA accident database. Because falls of ground often result in serious injury, MSHA "Fatalgrams" and fatal investigation reports provide a useful snapshot of ground control issues in the mining industry. These reports are available to the public (on the M FHA Web site at www.msha.gov). Fatalgrams, are one-page summaries that are usually published within a month of an accident. They contain very basic information about the accident with a graphic and a short section on relevant best practices. Fatal investigation reports are the official accident investigation reports filed by MSHA personnel. These reports contain general information about the mine, a, description of the accident, physical factors involved in the accident, a conclusion, and enforcement actions, Enforcement actions typically identify citations and discuss violations to the Federal Mining Law. MSHA also maintains comprehensive statistical data on the mining industry&apos;s accident and injury record. The law requires that mines file a report on every reportable accident that occurs, containing information on the accident&apos;s location, severity, classification, activity, and nature of injury A short narrative is generally included as well. Accident reports can be searched by many of the above fields.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A computer program has been developed to simulate evacuation of a mine in case of fire in the following, the capabilities, operations and structure of the program are described with illustrative examples to demonstrate usefulness of using the program. A detailed description of the program with sufficient information to make use of the program appears in Appendix B.

Jan 1, 1976

By Margaret R. Egan

The Bureau of Mines subjected three commercially available brands of transformer fluid to a series of combustion studies. The experiments were conducted in the intermediate-scale fire tunnel, which was designed to simulate environmental conditions in underground mines. The work was divided into three phases. In phase one, the brands were compared for gas production, smoke characteristics, and combustion yields. In phase two, the production constants of transformer fluids and other fuels were compared for the rate of formation of gas and smoke as a function of fire size. In phase three, several diameters of liquid-pool fires were compared in terms of fire size and burning rate. These transformer fluid measurements will be added to the existing coal and wood data that can be used as a basis of comparison for future studies of other mine combustibles. Further research into the combustion product emissions from combustible materials found in underground mines will lead to improved and realistic fire detection and suppression systems,

Jan 1, 1986

By J. R. Boyle

The Bureau of Mines developed cost estimates fur the disposal of phosphate rock washer slimes by pond settling, from a study of the method used at the International Minerals a Chemical Corp., Moralyn Phosphate Operations, Polk County, Fla. Data were obtained by basing phosphate production and slime generation statistics on plant capacity rather than on actual company records. Cost estimates, which were prepared as a guide in evaluating alternative disposal methods and in identifying needed areas of research, could be applicable to any Florida plant using the same disposal method. To conserve mineral resources and to improve environmental conditions, the Bureau recommends further research directed toward developing alternative methods of disposal, including the recovery of water and P205 values from the slimes.

Jan 1, 1969

By Leonard Obert

THE CRACKING AND POPPING of rock, often heard by men working underground, for years has been interpreted as a warning of danger and unstable ground. However, not until 1939 was it discovered that rock under stress generates subaudible and sometimes audible seismic disturbances (referred to as "micro-seismims" 4), which can be detected with the use of a suitable seismic apparatus. Since that date laboratory and field investigations have been in progress to ascertain to what extent this phenomenon can be utilized to detect, localize, and determine the magnitude of areas of instability in and around mine openings and to predict if and when failure will occur. These investigations have included a determination of the types of problems to which the method is applicable and the effect of rock type, geological defects, such as joints, fractures, faults, and other uncontrollable factors, on the reliability of results. Six reports have been prepared covering the investigations conducted between 1940 and 1952 (4-9). 5 These reports describe some of the characteristics of micro-seismims, as determined from both laboratory and field tests; the equipment used to pick up and record micro-seismims; the general test procedure and method of analyzing results; and applications of the method to specific mining problems.

Jan 1, 1957

By H. E. Hilliard

The Bureau of Mines investigated hydrometallurgical procedures for concentrating precious metals from a mechanically processed metal fraction of obsolete military electronic scrap. Feed material for the leaching procedures described in this report was the high-tension-separated metal concentrate obtained as a fraction from mechanically processing partially stripped electronic units. Initial pretreatment with a 20-wt-pct-NaOH solution solubilized most of the aluminum. After washing, the resulting residue was incinerated to destroy any organics attached to metal particles. The incinerated residue was leached with 20-vol-pct H2S04 solution using two methods, countercurrent pressure and ultrasonic-aided leaching to solubilize the base metals, predominantly copper. Silver was recovered from the base metal leach residue using 50-vol-pct HN03, and gold contaminated with several percent palladium was recovered from the silver leach residue using aqua regia. The impure silver and gold plus palladium products represent about 1.5 wt pct of the high-tension-separated metal concentrate. Included is a three-step process evaluation study of mechanical processing of general electronic scrap and two hydrometallurgical procedures for leaching high-tension-separated metallic concentrates obtained from the mechanical processing step. Process evaluation concluded that only mechanical processing is economically viable.

Jan 1, 1985

By Henry E. Perlee

Air compressor explosions that are caused by the ignition of combustible vapor mixtures cannot be explained by a single reaction mechanism or sequence of events. Explosions have been caused by the sudden release of large quantities of lubricating oil, by the rapid vaporization of oil that had accumulated slowly in high-pressure piping, and by the production of decomposition products from carbonaceous deposits. Ignitions can be caused by the heat produced in a catalytic reaction, in a compression process, or when a shock wave is propagated through a combustible vapor-air mixture. The frequency of these ignitions can be minimized by establishing proper maintenance and cleaning schedules. Further study is needed to satisfactorily correlate the various factors involved in compressor explosions.

Jan 1, 1963

By J. R. Sweet

The paper describing the raining operations at the Mt. Hope mine, Mt. Lope, N. J., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs of various mining operations in the United States. Mt. Hope mine produces magnetite ore. It is situated in the general northern part of the State of New Jersey. The towns of Rockaway, Wharton, and Dover lie within a radius of 4 miles from the mine. Dover is 40 miles from New York City.

Jan 1, 1932

By R. L. Benner

A compound stability diagram was constructed by the Bureau of Mines for the Zn-Fe-S-O system to show the phases that should be thermodynamically stable at various temperatures, oxygen pressures, and SO2 pressures. The diagram was demonstrated to have good qualitative value for predicting stable phases that may, in turn, be related to the recovery of zinc in the leaching phase of the electrolytic zinc process. The study showed that roasting temperature is the most Significant variable in preventing roaster formation of zinc ferrite, which is directly related to subsequent extraction of zinc in the leaching step.

Jan 1, 1966

By E. D. Gardner

This paper on the square-set system of mining embodies the results of a special study of the subject made as a part of the Bureau of Mines general investigation of mining methods and costs. Data for the paper were gathered by the authors during visits to mines using square-set mining, from Information Circulars prepared by consulting engineers to the Bureau on mining methods at individual mines, and from articles in the technical press and the Transactions of the American Institute of Mining and Metallurgical Engineers. The square-set system of mining is very widely applied and is one of the oldest methods in use in the United States. It is mainly employed for extracting relatively high-grade ore in heavy ground. It is also useful in taking out pillars left in mining by other methods. It is used to some extent as an auxiliary method with many underground systems and as an alternate with cut-and-fill, shrinkage, and open-stope methods when heavy ground is encountered. In some cases as much as 50 per cent of the ore may be extracted by square-setting at mines listed as using some other method of mining. A large tonnage is mined yearly by square-setting, principally in the Western States.

Jan 1, 1933

By Henry E. Perlee

Air compressor explosions that are caused by the ignition of combustible vapor mixtures cannot be explained by a single reaction mechanism or sequence of events. Explosions have been caused by the sudden release of large quantities of lubricating oil, by the rapid vaporization of oil that had accumulated slowly in high-pressure piping, and by the production of decomposition products from carbonaceous deposits. Ignitions can be caused by the heat produced in a catalytic reaction, in a compression process, or when a shock wave is propagated through a combustible vapor-air mixture. The frequency of these ignitions can be minimized by establishing proper maintenance and cleaning schedules. Further study is needed to satisfactorily correlate the various factors involved in compressor explosions.

Jan 1, 1963

By Geo. Adams Roalfe

THIS PAPER is one of a series being pre¬pared for and published by the United States Bureau of Mines describing, methods of mining and crushing and the costs of operation at commercial crushed-stone plants throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators, as well as to the industry as a whole. On the other hand, operating, costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. Acknowledgments The author wishes to acknowledge the [ ]

Jan 1, 1932

By R D. Fleming

A single-cylinder research engine was operated on pure hydrocarbons and simple (two-component) mixtures of pure hydrocarbons to study the effect of fuel composition on exhaust emissions from a spark-ignition engine. Used as fuels were three pure hydrocarbons that represented the primary hydrocarbon types present in commercial motor fuels: A paraffin (2,2,4-trimethylpentane), an olefin (2,4,4-trimethylpentene-2), and an aromatic (meta-xylene). The engine was operated at the same equivalence ratio for all of the fuels used in the experiment. Exhaust gas samples were collected and quantitatively analyzed for carbon monoxide, carbon dioxide, hydrogen, nitrogen oxides, aldehydes, and hydrocarbons. Exhaust hydrocarbons were separated and quantitatively measured with a chromatographic system employing a flame-ionization detector. Unknown hydrocarbons and oxygenated materials in the exhaust were identified with a Time-of-Flight mass spectrometer coupled to a chromatographic system. The results of the exhaust gas analyses showed that ethylbenzene, l-methyl-3-ethylbenzene, and l-methyl-3-vinylbenzene were more abundant in the exhausts from either 2,2,4-trimethylpentane--m-xylene or 2,4,4-trimethylpentene-2--m-xylene fuel mixtures than in exhaust produced from m-xylene. Also, the pure 2,4,4-trimethylpentene-2 fuel produced smaller amounts of C2 to C7 olefins in the exhaust than that produced by the pure 2,2,4-trimethylpentane fuel. The exhaust from pure m-xylene fuel contained aromatic hydrocarbons of higher molecular weight than the parent fuel. The amount of total hydrocarbon (moles of exhaust hydrocarbon per mole of fuel used) in the exhaust from the three pure fuels decreased in the following order: 2,2,4-trimethylpentane > 2,4,4-trimethylpentene-2 > m-xylene. The hydrocarbon mole-fractions of unreacted fuel in the exhausts produced from each of the pure fuels were 0.20 for 2,2,4-trimethylpentane, 0.13 for 2,4,4-trimethylpentene-2, and 0.66 for m-xylene.

Jan 1, 1970

By J. H. Holden, G. R. Strimbeck, L. F. Willmott, W. R. Huff

A pilot - scale fluidized feeder was developed for continuously feeding up to 1 ton of pulverized coal per hour to a pressure gasifier . Fluidization in the 3 - foot - diameter by 34-1 / 2 - foot - high feeder is effected by two streams of inert gas , a technique called zone fluidization . A stream of inert gas through a drilled plate in the base of a central column near the bottom of the feeder fluidizes the coal . Another stream through a drilled plate in the annulus between the central column and feeder wall provides a source of semifluidized coal for the central column . Fluidized coal from the central column discharges through an extraction funnel and discharge line . Zone fluidization provided good fluidization with moderate requirement for fluidizing gas . Instruments were developed for metering and recording the flow rate of fluidized coal . A system was developed for storing , and weighing pulverized coal , and then delivering it in fluidized form at about 1 to 8 tons per hour .

Jan 1, 1964

By G. B. Atkinson

The Bureau of Mines, in cooperation with McDermitt Mine, investigated a method for recovering mercury metal from mercury sulfide flotation concentrate by a hydrometallurgical technique. This preliminary report shows the feasibility of leaching mercury with a cupric chloride solution and electrowinning mercury from the solution. Proposed chemical reactions are shown in equations 1 through 3: 2CuC12 + HgS + 2CuCl + HgC12 + S°; (1) electrolysis HgC12 ?Hg + C12; (2) 2CuC1 + C12 ? 2CuC12. (3) A bench-scale leaching-electrowinning apparatus capable of treating 2.36 kg of sulfide concentrate in 11 days was operated continuously. An acid chloride solution containing, in grams per liter, 70 Ca, 60 Cu, 30 Fe, and 80 Hg was used as both leachant and electrolyte; 99.5 pct of the mercury was solubilized from the sulfide concentrate. Electrolysis of the leaching solution recovered mercury metal at an average current efficiency of 32 pct and an average energy consumption of 1.2 kwhr/lb Hg. Results from a preliminary economic evaluation indicated that a plant producing 31,500 flasks of mercury per year would have a capital cost of $3.7 million and an operating cost of $62 per flask of mercury.

Jan 1, 1983

By P. C. Good

To meet a growing need for thorium metal of high purity and amenability to fabrication, the Bureau of Mines devised a method for preparing thorium metal by the reduction of thorium tetrachloride. Thorium tetrachloride was prepared by chlorinating calcined thorium oxalate with carbon tetrachloride. The crude thorium tetrachloride, containing oxygen-bearing compounds, was purified by a double vacuum distillation at 800 to 900° C., and thorium metal was made in the form of a dense sponge by the reaction of metallic sodium or magnesium with thorium tetrachloride at 800° C. Vacuum arc melting was used to consolidate the sponge metal to ingot form for evaluation of its physical and chemical properties.

Jan 1, 1960

The U.S. Department of Labor?s Mine Safety and Health Administration (MSHA),through its winter alert program, warns U.S. mine operators and miners at underground coal mines of workplace hazards that can arise when the weather turns colder. MSHA records indicate that, historically, most explosions in underground coal mines occur during winter months. ?The changes in weather can increase the risk of fatal accidents,? says David G. Dye, Acting Assistant Secretary of Labor for Mine Safety and Health. ?Each miner and mine operator must take individual responsibility to eliminate the kinds of hazards that can cause fatal accidents in the workplace. Safety is not the other guy?s job?safety begins with you.? In fact, MSHA?s slogan for this year?s campaign is ?Winter Alert Starts Now and Safety Begins with YOU.? This message reminds miners and mine operators of the risks of colder weather and educates them about helping to reduce risks and hazards. ?Safety requires the joint effort of both management and labor,? Dye says. ?Everyone at the mine site must see safety as an individual value and act to ensure a safe working environment.?

Jan 1, 2006

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM&apos;s Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By K. E. Stanfield

The Bureau of Mines oil-shale program, initiated in April 1944, is concerned with the future utilization of oil shale in the United States as a source of liquid fuel. One phase of this program is the accumulation of information on the location, extent, and richness of oil-shale deposits that may be suitable for processing to oil and related products. A previous publication5/ presented, by means of logs, the oil yields of sections of the largest known oil-shale deposit in this country -the shales of the Green River formation occurring in adjoining portions of the states of Colorado, Utah, and Wyoming. This present supplementary report presents the oil yields of cores from 48 holes drilled during 1952 to 1954 in the Green River formation of Colorado, which is distributed over an area of more than 1,000 square miles. The oil yields of the 48 oil-shale sections, involving the assay of 9,651 samples, representing 22,451 feet of core, are presented by means of logs. In addition, the oil yields of samples comprising the maximum sections of 15 gallon-per-ton shale are tabulated for these cores and for the 28 cores from Colorado which were logged in the previous report.

Jan 1, 1957