Search Documents

By W. P. Diamond

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over-burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

By R. O. Dannenberg

Exploratory research was conducted to ascertain the feasibility of recovering beryllium from Spor Mountain, Utah, ore by the sodium fluosilicate (Na2SiF6) method used industrially for processing beryl. Na2SiF6 requirements to form water-soluble salts of beryllium were determined for three different samples--two clayey ores containing 0.6 and 1.3 pct BeO, respectively, and a calcareous ore containing 0.6 pct BeO. The ores were sintered with Na2SiF6 at 750° C for 3 hours. About 80 pct of the beryllium was rendered water soluble by sintering the 0.6-pct BeO ores with 30 and 40 lb Na2SiF6 per lb BeO contained in clayey and calcareous ores, respectively. The higher grade 1.3-pct BeO clayey ore required only 20 lb Na2SiF6 per lb BeO to solubilize over 80 pet of the beryllium. As the 0.6-pct BeO clayey ore was possibly the most representative of the deposit as presently delineated, leach liquor prepared from this sample was treated to recover beryllium salts. About 60 pet of the beryllium contained in the ore was recovered as beryllium hydroxide, which then was calcined to yield a 99-pct BeO final product by means of the following operations: (1) Sintering with Na2SiF2, (2) leaching with water, (3) precipitating crude Be(OH)2 by adding NaOH, (4) filtering to separate the hydroxide from the NaF solution, (5) redissolving the crude Be(OH)2 in excess NaOH, (6) filtering to reject caustic-insoluble impurities, and finally (7) boiling the Na2BeO2 filtrate from (8) to precipitate pure Be(OH)2. Reagent consumption was 49 lb Na2SiF6 per lb BeO recovered and 17 lb NaOH per lb BeO.

Jan 1, 1963

By Ronald D. Hill, Elmore C. Grim

Surface mining drastically alters the ecological characteristics of the area disturbed and in some cases has a decided effect on surrounding areas. Vegetation is removed, topographic features and characteristics are changed, and the original geologic overburden profiles are destroyed. Spoil banks generally are a heterogeneous mixture of rock fragments, rock particles, and soil-sized material derived from the overburden strata. With proper mining techniques, the various strata can be partially or completely segregated. Segregation of over- burden material offers the opportunity to bury the toxic, acid, or salt-pro producing strata under growth supporting material. In some situations, lower strata may have more desirable characteristics than surface material and can be placed near or on the surface. For example, limestone strata appear in some lower overburden profiles that have shale and/or sandstone near the surface. Also, some lower strata have higher nutrient levels that have been leached from the surface. Experience has shown that natural revegetation is a very slow process on strip mined areas. Native vegetation may not be compatible with the environment on the mined areas, for example : 1. Low nutrients in the spoil. 2. Toxic spoils (very acid or highly alkaline ). 3. Surrounding vegetation may be of the climax type and may not have pioneer- or primary-invader-type species present. 4. The seed source may be to far away from the adjacent mined areas. Early attempts to revegetate strip-mined lands with trees also proved to be unsatisfactory as they did not provide the initial ground cover required to stabilize the spoil. Erosion control with trees only may take up to 10 years before the canopies close and an effective cover is established. They are slow to form soil profiles and do not provide effective chemical pollution control until long after planting. A quick growing cover of herbaceous species is necessary to obtain quick stabilization and initial protection against erosion by reducing runoff and rain-drop splash. Vegetative cover will also build up a concentration of organic matter in the soil, which in turn will

Jan 1, 1974

By Raymond B. Ladoo

"The increasing realization of the fire hazards involved in the use of wooden shingles caused the National Lumber Manufacturers' Association to beginsome five years ago a search for a suitable fire-resistant paint. The problem was submitted to the Educational Bureau of the Paint Manufacturers' Association of the United States and work was started by Mr. Henry L. Gardner at the Institute of Industrial Research, Washington D.C. in collaboration with Dr. Herman von Schrenk, a timber expert of St. Louis.The results of this,work have been described by Heckel, in ""Asbestos"", (Heckel G.B., Asbestos in the Paint Industry, Asbestos, Vol. 2, July, 1920,pp.- 5-10).,,who gives the following formula for one of the colors as typical: It will be noted from this formula that ""asbestine"" forms 33% of the total liquid pigment by weight or 31.8% of the solid constituents. Hockel in the article referred to describes this paint,as ""asbestiform"" and assumes since ""asbestine"" is magnesium silicate it must be the chrysetile variety of ""Asbestine"", however, is not asbestos but is a trade name for a fibrous variety of talc mined in the Gouverneur district, St. Lawrence County, New York. This rather natural error persists through the article and credits asbestos with many desirable properties which are characteristics of talc."

Aug 1, 1920

By E. J. Gleim

A list of permissible mine equipment, tested and approved previous to January 1, 1942, was published In Bureau of Mines Information Circular 7207.3/ The present list covers additional equipment approved during the calendar year 1942. The items have been numbered to indicate the order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gives four air compressors on the Bureau's active list, and the present circular gives the fifth to be approved. Items 90 and 94 under Loading; Machines land Conveyors also appear in Information Circular 7207. These numbers are repeated hero to show that approval was granted during 1942 for additional voltages on machines previously listed one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those which may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that arc available for reducing explosion and other hazards incidental to coal mining. The present paper and Information Circular 7207 together give the complete list of all available permissible .Mine equipment.

Jan 1, 1943

By John P. Walsted

Because of the absence of an iron-producing industry, the Pacific Northwest is working under an economic handicap. This is particularly apparent in the gray-iron-foundry industry because of the high price of pig iron imported from foreign sources or shipped in from producing ?areas within the United States. The high prices and sometimes short supply of ferrous metal products has put a brake on industrialization, which has been only partly compensated by the availability of cheap electric power. The economic condition of the gray-iron-foundry industry could be improved by establishing a small iron-producing industry based on the locally available ores. Moreover, establishing a local iron smelter would create a market for resources now dormant. Low-grade ores of manganese, chromium, and nickel would become usable in industry when combined with the iron ore from Scappoose. Pig iron produced in even limited quantities would level out the fluctuation in supply. The ore deposits, being small, would not supply enough pig iron to satisfy the entire demand. This condition necessitates designing special pig irons that will carry abnormally high proportions of scrap in the cupola charge.

Jan 1, 1955

By Uldis Jansons

This report evaluates the economic Mining feasibility of four selected mineral deposit types that can be anticipated to be found in (d)(2) lands in the western Brooks Range, Alaska. The major assumption made for this study is the availability of a rail system for transporting equipment and concentrates for the base metal mines. Commodity prices used are those in existence in July 1976. Mine models were established based on known deposits and then evaluated. A lead-zinc-silver-barite deposit for which grades were available but ore reserves were assumed would require approximately 25% higher ore grades or higher metal prices to yield a 15% discounted cash-flow rate of return an the investment if mined at a rate of 10,000 tons per day open pit methods. Large copper-zinc mineral deposits could be mined economically at rates either of 5,000 tons per day underground or 10,000 tons per day by open pit methods. A high-grade copper deposit require a copper price of over one dollar ryes pound to yield an economic profit to be mined at 2,000 tons per day by underground methods. A small high-grade gold underground mine would require a gold price of about $295 per ounce to yield a 20% discounted cash-flow rate of return on investment if all new mine equipment were used and if existing labor rates were paid: Enterprising mining groups operating as partnerships might be able to operate this mine profitably at a gold price of about $152 per ounce, perhaps slightly less.

Jan 1, 2012

This publication contains 10 papers presented at a symposium on ATRS systems in Charleston, WV, on June 23, 1983. Included are papers by MSHA Technical Support (Roof Control), West Virginia Institute of Technology, the Bureau of Mines, and seven roof bolter manufacturers and/or designers of ATRS systems. These papers summarize the most recent developments in ATRS technology and can serve as a guide to potential designers, developers, and users of ATRS systems.

Jan 1, 1985

By W. M. Myers

[The principle of the application of electrolytes for deflocculation of fine materials in order that impurities may settle out, and the subsequent flocculation of the suspended particles by a different reagent, is well known and has been applied successfully to clays. Flocculation is also applied with success to ore slimes. Thus certain electrolytes, particularly alkalies added to a suspension of colloidal particles cause deflocculation so that, suspension may be-maintained indefinitely. The addition of bother electrolytes particularly acids, on the contrary produce's flocculation and the articles produce's are rapidly precipitated from suspension leaving a clear liquid above: the precipitated mass. Salts of trivalent elements such as aluminum act similarly. Due to its cheapness the double sulphate of aluminum and potassium, ordinary alum, has been used extensively for treating clays. These properties of electrolytes. and. their utilization in the commercial: preparation of clays have been described in publications of the Bureau of Mines.2]

Jan 1, 1927

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By R. L. Hopkins, H. T. Rall

A continuous method has been developed for preparing thiolacetic acid . Acetic anhydride and hydrogen sulfide are passed concurrently over an amine ion- exchange resin , under 20 - psi pressure . The thiolacetic acid , a product of the reaction , is flashed continuously from the crude reaction mixture and is purified by fractional distillation . The yield of thiolacetic acid is in excess of 80 percent based on the acetic anhydride charged . INTRODUCTION In the synthesis of reference compounds needed in the identification of sulfur compounds in petroleum , thiolacetic acid has become an important reagent because of its use in the synthesis of thiols by addition to appropriate olefins : R - CH = CH₂ + CH3 - COSH R- CH2 - CH2 - S - COCH R - CH2 - CH₂ - SH + CH3COONa NaOH (1 ) The commonly used procedures for its preparation , as described by Clark and Hartman (1 )4 and by Ellingboe (2 ) , are based on the batchwise reaction of acetic anhydride with hydrogen sulfide :

Jan 1, 1964

By Carlton E. Brown

Inquiries and instructional work on the determination of the number concentration of dust in atmospheres known or suspected to contain pneumoconiosis (silicosis and asbestosis) - producing particulate matter indicate a need for a description of the impinger method used by the Bureau of Mines. The impinger method consists of the collection of dust in a liquid medium and the counting under the microscope of the particles in a known portion of this liquid. The dust-collecting device is called an impinger. The dust in the air drawn through this collector at a known rate impinges at high velocity upon a smooth surface under a bubbling column of liquid. The dust is either picked up from this surface by the liquid or removed from the air as it passes through the liquid.

Jan 1, 1938

China?s New Steel Complex Postponed. - The planned $5 billion Baoshan Steel Works near Shanghai is being laid aside for 6 months to a year, and may be abandoned altogether. The second phase of construction, in which Wean United, Inc., of Pittsburgh was a major participant, has definitely been cancelled. Over $1 billion had been committed to the 6 million-ton-per-year plant. U.S. Firm Develops South African Fluorspar. - The Armco Bronne Co. of Middletown, Ohio, plans to spend $27 million to develop a fluorspar mine in the Republic of South Africa, With fluorspar reserves at 20 million metric tons, the project is planned to produce 200,000 tons Per year of fluorspar for export starting in 1983. U.S.S.R. Resumes Sales of Titanium Sponge. - Against a background of increased U.S. titanium sponge supplies, the Soviet Union is offering limited quantities of this commodity to the U.S. market at approximately $10.00 per pound, down from $25.00 per pound last year.

Jan 1, 1981

By D. B. Dow

The appearance of water in an oil field is the forerunner of various difficulties, and probably represents the greatest technical problem that the producer must face. Water conditions bear-directly on the quantity of oil recovered, and the length of the life of a field. Presence of mater increases the cost of operation, for example, gifting costs. On account of the corrosive action of oil-field waters on pumps and other equipment, frequent replacement of equipment is necessary. Furthermore, water may affect the marketability of the oil produced, as detrimental emulsions of water in oil (?B.S.?, "cut oil", etc.) are often formed. The writer has recently completed a study of oil-field emulsions. The present paper deals with the factors responsible for the formation of emulsions. This will be followed by another dealing with methods now utilized for dehydrating oil-field emulsions, and by a third dealing with the physical chemistry involved in the formation and resolution of such emulsions.

Jan 1, 1925

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

By H. F. Feldmann

This Bureau of Mines report presents a method for the computer solution of the equilibrium compositions of any complex, multiphase, chemical system for which appropriate thermodynamic data are available. The method describes in detail the computation of systems in which solid or liquid species can form by heterogeneous chemical reactions where these species do not occur in any equilibrium equations. Also described are the calculation of phases formed by condensation (pure or solutions) and the inclusion of other system restrictions such as electroneutrality. The method is being used to compute the equilibrium composition of mixtures of an electrically conductive plasma and a liquid slag phase arising from the high-temperature combustion of coal for magnetohydrodynamic power generation. These mixtures can contain up to 65 species including gases, liquids, free electrons, and ions.

Jan 1, 1969

By Nicholas Kyriazi

The Bureau of Mines subjected three commercial compressed-oxygen self-contained self-rescuers to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The environmental treatments consisted of extremes of temperature and of shock and vibration. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. A critical concern was internal damage to an apparatus that would cause it to malfunction or seriously degrade its performance without any obvious external signs. The Bureau has previously tested chemical oxygen self-contained self-rescuers in a similar research program. Although the three compressed-oxygen units are not as sturdy as the chemical oxygen self-rescuers tested previously, they performed reliably after treatments on treadmill tests with human subjects and on machine tests using a breathing and metabolic simulator. Serious damage was caused by both the heat treat-ment of 71° C (venting of the 02 bottle in most cases), and in the shock treatment (breaking open of the case and dislodging of the components). When physical damage is obvious, a complete refurbishing of the damaged self-rescuer is recommended.

Jan 1, 1983

By J. E. Tiffany

"The new permissible blasting device, Cardox, utilizes as a blasting agent liquid carbon dioxide which is discharged.as a gas from a steel container or shell. The loaded shell is placed in a borehole, stemmed, and tamped in a manner similar to that employed with explosives, and is fired by electricity.The Bureau of Mines' approval for use of the device in coal mines was granted as Approval No. 1 under date of October 3, 1928; as the result of tests made under the conditions and requirements of Schedule 20. There have been three subsequent extensions whereby minor modifications in the original design were granted.The permissibility of the device is subject to the following conditions; (1) It shall be in all respects similar to the sample submitted for tests; (2) certain thicknesses of disc and. weights of heater ingredient and of carbon dioxide, all of which are set forth in Table 2 under the provisions governing permissibility, must be used: (3) the rear cap must always be in place after the shell has been charged, to prevent accidental firing; and (4) firing must be done by means of a permissible-type blasting unit.The permissibility of Cardox was established by gallery tests similar to those used in testing explosives for permissibility. In these tests the shell was discharged into gallery 1 without causing any ignition of gas and air or of gas, dust, and air mixtures there. The conditions of charging the shell, such as weight of the ingredients of the heater element, the carbon dioxide charge, and thicknesses of the disc, were varied according to the conditions under which it would be likely to be used in blasting. The tests made in gallery 1 are here described in detail, as are also the tests which have been made for determining the propulsive strength of the device and the quantities of poisonous gases given off when a shell is discharged."

Mar 1, 1929

By M. M. Jones

A procedure for the spectrophotometric determination of uranium has been developed in support of minerals research being conducted by the Bureau of Mines. Uranium is separated from the sample by tributylphosphate extraction from acid solution containing added aluminum nitrate and (ethylene dinitrilo)-tetraacetic acid solutions. The colored uranium-dibenzoy1methane complex is developed in the organic phase by adding an ethanol solution of dibenzoylmethane buffered with triethanolamine. Absorbance is measured at 410 nanometers, and the response is linear up to at least 100 micrograms U30S in the aqueous aliquot taken for analysis. Aliquots containing as little as 8 micrograms U30S may be analyzed with relative errors no greater than ±5 percent. For aliquots containing at least 35 micrograms U308, relative standard deviation at the 95-percent confidence level is about ±2.2 percent. Appropriate procedures are given for analyzing a wide variety of samples.

Jan 1, 1980