Search Documents

By R. V. Ramani, R. Bhaskar

"IntroductionThe behavior of dust clouds in mine atmospheres has been a subject of longstanding interest due to both health and safety reasons. Pioneering studies in Germany and SMRE focussed on ambient dust concentration, principally aimed at determining optimum velocities for effective dilution. A summary of studies related to this area is provided by Hall,(l) Efforts to understand dust deposition from the explosion hazard point of view led to experiments in return airways (2-4) followed by experiments in longwalls.(5) Concerted efforts, either experimental or theoretical, were not made until recently to relate ambient concentration with dust deposition in mines. In 1974 Hwang et a1 (6) developed a computer model to predict dust concentration which considered deposition-concentration relationships. Also, experimental studies involving concurrent dust deposition and ambient concentration were conducted in the U.S. by Courtney et al (7 ) in operating mines. Efforts to relate theory with experimental results have been made by Owen (8) and Hwang et al (6 ) for dust deposition. There has been limited work, however, to determine the application of the theories and assumptions from aerosol sciences for modeling dust flows in mine atmospheres. (9 ) This is the objective of the work currently underway in the Generic Technology Center on Respirable Dust since· 1983 under a project titled, ""Prediction of Ambient Dust Concentration in Mine Atmospheres."" The scope of the project activities include:1. Development of a mathematical model to predict dust deposition and concentration in mine atmospheres.2. Experimental studies on dust transport and deposition in mine airways.3. Comparison of the model results with the experimental data."

Mar 1, 1989

By R. S. Conti

This U.S. Bureau of Mines (USBM) report discusses the results of research conducted in the USBM experimental mine at its Lake Lynn Laboratory to determine the alarm times of smoke and carbon monoxide (CO) sensors, and a point type heat sensor (PTIIS) to slowly developing coal-conveyor belt fires. The tests were conducted at air velocities of 0.44 and 0.97 m/s, The data clearly indicate that smoke sensors provide earlier warning of fire than 10 ppm CO sensors, and that 10 ppm CO sensors provide earlier warning than PTHS, A success rate of 1.0 (indicating detection of every test fire) was obtained for both smoke and C8 sensors. For the PTHS, the success rate was 0.57 at the lower air velocity, decreasing to 0 at the higher air velocity, Data are also presented showing the sequence of fire events and detection events at the two air velocities as a function of time. Results show that early detection and warning of underground mine fires will improve the probability of miners' escape.

Jan 1, 2010

To develop a magnetic levitation transport system that can reduce the cost and improve safety in transporting coal from the face of underground coal mines to the surface. Background Many conventional mining operations use conveyor belts to transport coal from an underground face to the surface of the mine. The Mag-Lev Transport System design replaces conveyor belts with magnetically levitated coal haulage containers moving through a dedicated pipe¬line. Cost estimates, based on current design data, show the Mag-Lev Transport System would have operating and capital costs that are less than or equal to those of an equivalent-capacity conveyor belt system. The safety hazards associated with conveyor belt systems include exposure to moving parts and pinch points, potential fire hazards due to mechanical friction, and the exposure of miners to respirable dust. These hazards would be eliminated or significantly reduced by this novel technology. Approach The Mag-Lev Transport System uses magnetic levitation technology that allows noncontact, frictionless conveyance of a levitated body within a dedicated transit corridor. The mag-lev technology utilizes two types of permanent magnets coupled with an electronic position control system to achieve noncontact levitation. Levitation is provided by neodymium-iron boron (NdFeB) magnets mounted in the base of the haulage containers and inexpensive ceramic-5 magnets located in the bed of the transit corridor. An electronic position control system is used to overcome the inherent instability of the repelling permanent magnets. Proximity sensors, a signal processing circuit, electromagnetic actuators, and fixed ferrous side rails are the major components of the positioning system.

Jan 1, 1994

By S. R. B. Cooke, J. Bruce Clemmer, F. P. Diener

"The limestone deposit utilized by one of the plants of the Universal Atlas Cement Co. is covered in part by a stratum of cherty limestone. If this overlying deposit could be utilized by removing the excess of chert economically, quarry costs could be reduced and the amount of rock economically available would be increased greatly. On account of the distribution of flint and limestone, a product fairly free of flint can be obtained until the quarry face is about 50 or 55 feet high. As the face is worked farther back into the hill, the comparatively clean stone is overlain with a constantly increasing amount of high-flint limestone. If this flint remained with the limestone, there would be a prohititively high silica ratio in the finished cement; if the flinty layer were removed as overburden a very large tonnage would be handled and much good stone lost. Consequently it was felt that means should be devised for separating the flint from the limestone after it reaches the plant.The investigation was undertaken by the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Universal Atlas Cement Co. and the Missouri School of Mines and Metallurgy, Rolla, Mo.CONSIDERATION OF PROCESSESMany schemes for the separation of Minerals are based on differences in the specific gravities of the minerals to be separated. In this case the flint has a specific gravity of approximately 2.62 while the limestone averages about 2.70. This differential is not large enough to permit separation by any method based on specific gravity. Furthermore, all the limestone particles in any given sample are not alike; usually about 10 percent of them have a specific gravity the same as, or lower than, the flint."

Mar 1, 1935

By J. M. Singer

The objective of this investigation was to determine minimum air velocities and entrainment rates for coal and rock dust dispersion in wind tunnel experiments under conditions that simulate dispersion from surfaces in coal mines where airflows are induced by weak gas explosions. Dust deposits were bed-or ridge-shaped; particle sizes were 6 to 80 microns (cohesive deposits) or 100 to 150 microns (free-flowing deposits); and wind tunnels were 7.62 cm wide by 5.08 cm high by 300 cm long, and 2.4 m wide by 1.5 m high by 215 m long. The investigation showed that minimum air velocities (directed at mid-height) of separate, layered, or mixed piles of coal dust and rock dust were within the range 5 to 30 m/sec, independent of size of wind tunnel. This finding considerably facilitates scaling of data to mine-size passageways. Free-flowing deposits dispersed relatively slowly by single-particle detachment; cohesive dusts dispersed faster by the breaking and lifting of large clumps along weak failure flames; particle dispersion occurred in flight. Layered or mixed deposits of coal and rock dust did not disperse selectively. Semiempirical expressions were derived relating minimum air velocities and dispersion rates to dust-pile geometry, cohesion, porosity, and bulk density.

Jan 1, 1972

By R. J. Gajan

As part of its research program on secondary metal refining, the Federal Bureau of Mines has developed a fast method for determining aluminum, iron, copper, cadmium, and lead in zinc-base alloys. The new method is intended for use by trained technicians in laboratories with inexpensive equipment. It can be used either in the analytical laboratories of the many small plants that are characteristic of the secondary metals industry or in laboratories engaged in basic research to improve refining processes. A complete analysis for the foregoing elements can be made in less than 3 hours from a single sample in solution. The method is especially helpful when a small amount of sample is available. Aluminum and iron are determined spectrophotometrically and the other elements polarographically. The new method is now being used for control analysis in metallurgical research, and the results compare favorably with previously used spectrographic methods. Luke and Braun4/ described a photometric method for the determination of aluminum in zinc diecasting alloys in which the aluminum was complexed with Aluminon reagent (ammonium salt of aurintricarboxylic acid), forming a red lake. An adaptation of this method was used for determining aluminum. Beers law is obeyed between 0.01 and 0.06 milligram of aluminum.

Jan 1, 1961

By R. S. DeCesare

Operation of the Bureau of Mines raw refuse continuous separation pilot plant is described, including modifications made to plant equipment for improved performance. Products recovered from refuse, many of which have been evaluated by other laboratories and private firms, are discussed. Sampling procedures used in the pilot plant and detailed data obtained from processing refuse from 13 municipalities are presented in appendixes. Fuel evaluations made on combustible fractions of refuse from the various municipalities are also presented. Information and data obtained at the pilot plant have been used to assist many municipalities in solving their urban refuse problems.

Jan 1, 1980

By Floyd G. Anderson

The increasing trend toward use of continuous-type mining machines created a significant dust problem in coal mining, which resolved itself into three categories: Visibility at face, deposition on return airways, and the potential health hazard. The control measures applicable to these conditions and studied or developed from 1955 through 1957 are summarized and reviewed in this report. Other important problems brought into focus during the same period were radiation exposure in uranium mining and high temperature and humidity. Although temperature and atmospheric pressure alone may not be contributing factors in the incidence of silicosis, the few mining companies who operate under the extremes of these conditions are dust conscious and keep dust-control engineers on their operating staffs.

Jan 1, 1961

By N. L. Wimmler

"INRODUCTIONSedimentary deposits of titaniferrous magnetite occur at various localities in the eastern foothills of the Teton Ranse in Deer Lodge County, Mont. The Choteau deposit was examined by a Bureau of Mines engineer in August 1942. An exploration project was recommended.Core drilling exploration was begun in June 1945; it was concluded in August 1945, Seventy-six holes were drilled. This report presents the data obtained by the Bureau of Mines exploration.ACKNOWLEDGMENTIn its program of exploration of mineral, deposits, the Bureau of Mines has as its primary objective, the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, Chief, conducts preliminary examination, performs the actual exploratory work, and prepares the final, report. The. Metallurgical Branch, R. G. Knickerbocker, Chief, analyzes samples and performs beneficiation tests. Both of these branches are under the supervision of Dr. R. S. Dean, Assistant-Director. The field work was supervised by Earshel W. Newman, engineer in charge of the Helena Field Office. D. B. Hoiekvam was the project engineer; he provided most of the data used in the preparation of this report."

Dec 1, 1946

By Clete R. Stephan, Mark J. Schultz, William A. Slivensky, Eric S. Weiss, Kenneth W. Jackson

he Pittsburgh Research Center (PRC)~ and the Mine Safety and Health Administration (MSHA) are participating in a research program to evaluate the strength characteristics and air leakage resistance of seals and water trap designs for use in underground coal mines. This program is being conducted at PRC's Lake Lynn Laboratory near Fairchance, Fayette County, PA. Seals designed with a 40-cm-thick polymer (polyurethane) and aggregate core between two dry-stacked (no mortar) concrete block walls (coated on out by sides) withstood a 138-kPa pressure pulse while maintaining acceptable air leakage rates. Similar seal designs utilizing a 97-cm-thick, 91-kg/m7-density, polymer-only core did not survive; however, a 5 1 -cm-thick, 203-kg/mi-density, polymer-only core seal successfully withstood the explosion pressures. Evaluations of cellular concrete seal designs have shown that a two-pour slurry injection technique did not adversely affect the strength of the 1.2-m-thick seals when subjected to a 138-kPa pressure pulse. Two seal designs utilizing low-density cementitious block have also been evaluated with successful results. In addition to seal strength tests, various 15- and 30-cm-diam U-shaped water trap pipes and a water trough design were evaluated under explosion conditions and were shown to be inadequate when evaluated under worst-case conditions. Simple modifications to the various water trap designs were successfu1 in preventing the passage of explosion flame through the trap.

Jan 4, 1996

By S. R. Borrowman

Physical beneficiation, leaching, and solvent extraction investigations were made to recover a high-grade thorium oxide product from Bald Mountain, Wyo., conglomerate. The monazite in the Bald Mountain deposit contains 8.8 percent Th02 and, therefore, is higher in thorium content than the usual domestic or foreign monazite. A sample of composited drill cuttings for the study contained 4.3 pounds of monazite per ton of are. The work showed that the monazite, although unusually fine grained and friable, could be concentrated by tabling and magnetic treatment to yield a product assaying 5.65 percent Th02 with a recovery of 61 percent of the thorium. Subsequent decomposition of the concentrate by treatment with sulfuric acid and solvent extraction of the resultant solution with a primary aliphatic amine yielded a thorium oxide product of 99-percent grade.

Jan 1, 1962

By M. J. Ferrante

Relative enthalpies of high-purity disodium hexatitanate (Na2Ti6013) were measured at the Bureau of Mines to provide new thermodynamic data needed to advance the technology of materials. Measurements from 298.15 to 1,478 K were made by drop calorimetry with a copper block. Tabulated values are listed for the standard relative enthalpy, heat capacity, en-tropy, and Gibbs energy function between 298.15 and 1,500 K. Enthalpy data are also given in equation form and are combined with thermodynamic data from the literature to derive values of standard enthalpies of formation, Gibbs energies of formation, and logarithms of the equilibrium constants of formation. Similar calculations were made for the reaction of Na20 with Ti02.

Jan 1, 1986

By Eugene T. Sheridan

The annual survey of the fuel-briquet industry by the Bureau of Mines, United States Department of the Interior, revealed that 21 fuel-briquet plants in 11 States were in operation and reported production in 1956. The demand for fuel briquets in the United States has gradually declined since 1948, and the number of operating plants has decreased from 36 to 21. Also, the annual productive capacity of the industry has decreased, although not a proportionate amount because most of the plants that were abandoned were small and in most instances had a designed capacity of less than 25,000 tons per year. In 1956 the 21 active plants had an annual capacity of 3.7 million tons (table 2), which was only 20 percent less than the total capacity of the 36 plants in 1948. This indicates that most of the larger plants have remained active, even though operating at reduced rates, and the average capacity of the industry has increased from 130,000 tons per plant in 1948 to 177,000 tons in 1956. Since 1948 operating rates have decreased from 67 percent to 41 percent of annual capacity.

Jan 1, 1958

By Henry M. Harris, John E. Kelley, Thomas D. Roberts

A penetrometer apparatus for measuring viscosity of glass at temperatures up to 1,450 ° C was developed for use in establishing the viscosity coefficients required for high- temperature forming of ceramic materials . The major advantage of the method is that it can be used with samples of almost any shape or size without the necessity of forming or measuring shapes to close dimensional tolerances . Also , it has proved accurate in the range of 106 to 109 poises , a gap between the normal limits of other methods . The device , which operates on a single penetrometer principle , was used to determine the absolute viscosity coefficient of substances in centimeter - gram- second units of poises instead of relative penetration - rate units as with other penetrometers . Penetration of the viscous sample was sensed with a linear , variable differential transformer . The output of this transformer was recorded versus time , and the penetration rate was used in calculating the viscosity coefficient . The general equation relating penetration rate and viscosity coefficient was found to be 11 = F ( ln L/a 0.72 ) 2 π UL · where is the viscosity coefficient in poises , F is the penetrator load in dynes , L is the penetration depth in centimeters, a is the penetrator radius in centimeters and U is the penetration rate in centimeters per second . The penetrometer was tested using a standard viscosity sample of sodalime - silica glass obtained from the National Bureau of Standards ( NBS ) . Values obtained at several temperatures all agreed within 10 percent with comparable data calculated from the Fulcher equation derived by NBS for this glass . Equivalent accuracy was obtained with other glasses used to evaluate the apparatus .

Jan 1, 1964

By J. W. Horne, W. L. Finley, A. D. Bauer, D. W. Gould

"The Bureau of Mines and the State of Colorado are cooperating in an investigation of the oil shales of Colorado. in this report the yields and the results of analyses of the oil and, gas produced from a number of oil-shale samples from the principal deposits of Colorado and other oil-shale States, are compared with samples from Scotland and Australia, where the oil-shale industry has had its greatest commercial development, and also with a sample from Brazil *here extensive oil-shale deposits are found shale samples were not selected as being representative of the different deposits, but they illustrate the wide variation in the nature of the organic matter of different oil shales.A further study is being made of the chemical composition of the shale, distribution of nitrogen and sulphur. in the products, temperatures at which organic matter decomposes, and the results will be presented in subsequent Papers, With complete data available on the chemical composition of the shales, it may be possible to explain some of the differences in the nature of the products from the various shales,Most of the work described herein was done under the supervision of M. J. Gavin. L. C. Karrick, formerly of .the Boulder laboratory, assisted in the work and gave many valuable suggestions."

May 1, 1924

By M. S. Seehra, V. S. Babu

"INTRODUCTION The accurate determination of the free silica index in coal mine dusts is an important requirement because severe health hazards are believed to be associated with the inhalation of respirable-sized silica particles.1-6 Free silica refers to the three polymorphs of silica (Si02)viz., quartz, cristobalite, and tridymite-although quartz is usually the dominant form in most mine dusts.6 The free silica index is the concentration in micrograms of free silica in air per m3 of air sampled corrected to standard conditions of 25°C and 760 mm/Hg, the present MSHA (Mine Safety and Health Administration) limit on time-averaged basis being 100 µ.g/m 3 for coal mines. A recent review7 has concluded that quartz, cristobalite, and tridymite particles impart nearly equal long-term hemolytic damage when compared on a per unit surface area basis.At present, two experimental methods-viz., transmission infrared spectroscopy (TIRS) and x-ray diffraction (XRD)-are commonly used for the determination of silica concentrations in mine dusts. In TIRS, which has been adopted by MSHA and is commonly called the P7 method, the silica absorption band near 800 cm - 1 is used for quantification. However the mineral kaolinite, which is commonly present in mine dusts, also has absorption band, albeit weaker, at 800 cm- 1• To correct for this interference, one uses the stronger 915-cm -1 band of kaolinite to determine the concentration of kaolinite, and the kaolinite contribution to the absorbance at 800 cm-1 is then determined from a calibration curve, leading to the determination of silica by subtraction. In the XRD technique, usually an internal standard such as CaF 2 is used to determine the concentration of silica from line intensity measurements. XRD has the added advantage that concentrations of quartz, cristobalite, and tridymite can be determined.8•9 In an exhaustive study on the precision of the techniques ofTIRS and XRD for monitoring worker exposure,9 the conclusion has been reached that both methods measure silica within 253 of the ""true"" value 953 of the time in a single laboratory."

Nov 1, 1995

By R. Hogg

"The problems of sampling particulate materials, and of characterizing the distributions of particle size and composition are reviewed. Requirements for sampling from comminution systems are discussed and a simple formula is presented for estimating the minimum sample size needed. The limitations and errors associated with the techniques available for particle size analysis are evaluated and guidelines are suggested for the selection of appropriate methods. The use of microscopic and macroscopic approaches to the characterization of particle composition are discussed.INTRODUCTIONComminution is a process of particle size reduction in which the goal is to produce a material with a specified particle size distribution from a coarser feed. In mineral processing applications, the product size distribution is often qf secondary importance to the extent to which individual mineral grams can be liberated from one another. However, due to poor understanding of the nature of the liberation process and the lack of reliable procedures for characterizing it, the actual specification is normally in terms of particle size.Particle size distribution can be regarded as the fundamental characteristic of a particulate system. The distributions of particle shape and composition among the various particle sizes present are often sufficient to define the bulk properties and behavior of the system. Description of the distributions of size; shape and composition of the different phases which may exist within individual particles is necessary to complete the picture and is especially important for predicting liberation etc., in comminution processes. It is quite obvious that · the complete characterization of real particulate systems is a formidable, if not .impossible task. Practical characterization procedures should involve ·evaluation of those characteristics which are deemed to be important and which can be measured. In comminution systems, this should ideally include the particle size distribution, the size-by-size distributions of particle composition, and as much information as can be acquired on the internal composition and structure of individual particles. In most cases, of course, we fall far short of even this rather limited goal."

Jan 1, 1988

By F. P. Haver

The purpose of this investigation was to determine the effect of common impurities, that is, oxygen, nitrogen, carbon, and iron, on the Brinell hardness of electrolytic titanium. On a weight basis, nitrogen had the greatest hardening effect, followed by oxygen, carbon, and iron in order. The hardening effects of oxygen and carbon were almost identical up to a concentration of approximately 0.1 percent by weight. Above this concentration, the relative hardening effect of carbon decreased rapidly, possibly because of its limited solid solubility in a-titanium. Hardness vs. composition curves for both oxygen and nitrogen were essentially straight lines over the range of Brinell hardness numbers (B.h.n.) covered in the investigation. The hardness of titanium was also determined as a function of the percentage of impurity atoms. On this basis, iron in concentrations up to 0.17 atomic percent had a greater hardening effect than either oxygen or carbon. INTRODUCTION Determination of the as-cast hardness of arc-melted titanium is a method of quality control widely used in industry. Numerous studies4/ have been made of the effect of impurities on the hardness obtained by this method. However, most of them have been based on the use of either iodide titanium or commercially pure Kroll sponge (B.h.n. >90), as a starting material.

Jan 1, 1959

The Technology Transfer Seminar on Mine Communications held on March 21-22, 1973, at the Pittsburgh Mining and Safety Research Center, Bruceton, Pa., presented information about recently developed equipment, instruments, and techniques for use in mine communications systems. All of the basic ideas presented in the fine seminar are operational in the Bureau of Mines Safety Research Mine in Bruceton.

Jan 1, 1974

By H. H. Schrenk, W. P. Yant, P. H. Mautz

"In a study of the chemistry and pathology of chronic benzene poisoning, which was conducted cooperatively by the United. States Bureau of Mines, the Barrett Co., and the producers of benzene, it was necessary to make quantitative determinatious of the abzorption, distribution, and: fate of benzene in the organism. Although methods for determining benzene in relatively large amounts were available no satisfactory method was found for removing and determining the small amounts that are present in the tissues or excretions after exposure to conditions which ultimately cause chronic poisoning. This no doubt accounts for the lack of information in the literature on this particular phase of benzene poisoning.The writers have found in work that will be described in a subsequent publication that the amounts of benzene present in the tissues and excretions under conditions of exposure which produce chronic benzene poisoning arc of the order of a fraction to a few milligrams per 100 grams of tissue. This report describes a method developed and found satisfactory for these determina¬tions.RÉSUMÉ OF PERVIOUS METHODSA method for the determination of benzene in tissue was developed by Joachimoglu. 5 In the Joachimoglu procedure the ground organs are mixed with water and acidified with diluted sulphuzic acid, and the benzene is distilled into a receiver containing carbon tetrachloride. The benzene is nitrated in the carbon tetrachloride, the carbon tetrachloride evaporated, the acid mix¬ture neutralized, and the dinitrobenzene extracted with ether. After removal of the ether the dinitrobeuzene is determined gravimetrically. Joachimoglu reports that this method is about 55 to 60 percent quantitative."

Aug 1, 1935