Search Documents

By C. P. Mangelsdorf

When the finely bedded shale frequently encountered over coal seams experiences a separation, the material below the separation must behave like a beam or plate in that it must resist both bending and shear. Be-cause of the weakness in interlaminar shear inherent in such strata, shear deflections that are usually ignored in isotropic beam theory may account for a significant part of the total roof sag. Similarly, when a roof truss is installed in such a roof the upward displacement reducing the sag will have components due to shear as well as bending. Questions asked by mine operators about the installation of roof trusses frequently deal with optimum position, slope, and initial tension of the inclined chords. This Bureau of Mines report examines the effects of those chord parameters on the strain energy of both shear and bending and offers optimum values that will minimize the total strain energy of the immediate roof. Design charts are provided, several design examples are included, and the results are compared with current practice. The effects of in situ stresses are investigated and are shown to be equivalent to an additional load on the beam.

Jan 1, 1988

By Noel N. Moebs

The Bureau of Mines investigated severe coal mine roof support problems along a section of main entries in the Pittsburgh coalbed in southwestern Pennsylvania to identify the causative factors. The mine roof was examined in detail, and various sedimentary structures are described that contributed directly to irregular and unstable roof. Small-scale paleochannels, scours, and related slickensides were identified as the leading cause of bad roof, and isopach maps were prepared to illustrate a method whereby the presence of these structures could be inferred in advance of mining. Probably second in importance was the occurrence of relatively incompetent flaggy, poorly cemented sandstone, weakened by coal and micaceous laminea. No effect of in situ stresses on roof stability was detected.

Jan 1, 1977

By S. E. Khalafalla

The Bureau of Mines investigated the metallothermic reduction of copper oxide as a function of temperature, reactant proportions, form of reductant, and gaseous environment, using iron and steel scrap reductants. The reaction proceeded rapidly with powdered iron at temperatures above 560° C, attaining over 95 percent copper metallization within 3 hours. The importance of inter-reactant contacts on the extent of the reaction was evident from the variable, but usually lesser, degree of metallization obtained with iron from tin cans and automobile steel scrap. Reduction decreased as the molar ratio of copper to iron increased between 1 and 3. The most favorable gaseous environment for the reaction was a static helium atmosphere containing about 0.6 percent water vapor. Ferrothermic extraction of copper from its oxides appears to be essentially a "solid-state cementation" process. While ordinary cementation processes must be preceded by leaching, the ferrothermic method avoids this generally slow step and also the water pollution caused by the leaching agents. Sulfidic copper concentrates could likewise be reduced with metallic iron following their complete oxidative roasting.

Jan 1, 1969

By C. J. Walker

The ever-increasing use off natural underground formations for storing natural gas has focused attention on the behavior of such storage formations under varying operating conditions. The need for a means of evaluating in¬dividual wells and groups of wells has become manifest. It is essential that industry and others be able to determine the rates of flow that can be ex¬pected from a given well or group of wells under different conditions and to ascertain whether certain wells are deteriorating. Such questions need more exact answers now than ever before because of the vital role underground gas storage plays in the industrial and domestic consumption of natural gas. The Bureau of Mines--in cooperation with the American Gas Association--has main¬tained an active interest in gas-well testing because of the implications of such test procedures on the consumption and efficient production of natural gas. A basis for testing gas wells was provided by the back-pressure method of Rawlins and Schellhardt (12).4/ They showed that for normal gas wells there is a consistent relationship between rates of delivery of gas and corresponding pressures when the formation pressures are used as the basis of interpretation, The equation for this relationship is as follows: Q = C (Pf2 - Ps2)n where; Q = rate of flow, generally expressed in cubic feet per 24 hours. C = a coefficient.

Jan 1, 1960

By John A. Johnson

Tests ere conducted at the Mount Weather testing adit of the 57 Bureau of Mines on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. Equipment Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is mace of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.

Jan 1, 1939

By Robert L. Crosby

The Bureau of Mines investigated the substitution of cement copper powder for commercial copper powder in an Fe-7 pct Cu-l pct C powder metallurgy alloy. Copper powders from six different commercial cementation operations were separately upgraded by screening and hydrogen reduction. They were then mixed with commercial iron and graphite powders to form the Fe-7 pct Cu-l pct C alloy. Various chemical and physical properties were determined on the upgraded cement copper and the alloy powders. Mechanical, physical, and chemical properties were determined on green and sintered specimens made from the alloy powders. Mean tensile and bending strength of sintered specimens were significantly lower than the means from specimens made from commercial metal powders. The lower strengths are apparently related to poor sinterability.

Jan 1, 1970

By J. E. Tiffany

A stick of explosive is a package of stored energy that can be released when needed to blast rocks, coal, and other materials; but, unlike fuels such as coal and gasoline, its potential energy is self-contained, there being enough oxygen within the package to complete the almost instantaneous reaction. When an explosive is ignited or detonated, the solid or liquid materials of which it is composed are converted rapidly into highly heated gases, which, if free to expand, would have a volume many times larger than that of the original explosive. At the instant of explosion these gases occupy only the volume of the shot hole and are therefore produced at a very high pressure, which causes the material that is being blasted to be broken or disrupted. In blasting coal efficiently the proper placement of the shot hole and the confinement of the explosive therein are both of prime importance. When these are not adjusted properly, only a small amount of the energy is expended in bringing down coal, consequently the balance of the energy tends to be expended by the emission of a flame into the working place that may lead to a gas or dust explosion. Permissible Explosives Defined The term "permissible explosive", as applied by the Bureau of Mines to explosives it has approved for use in blasting in coal mines, embraces not only the requirement that the explosive, when used, shall be similar in all respects to the basic sample that passed all the tests necessary for its admission to the published permissible list, but also that the explosive shall be used under certain prescribed requirements.

Jan 1, 1938

By Robert J. Hundhausen

This information circular is one of a series of Bureau of Mines reports dealing with mining and milling methods and costs . It describes the operations at the Little Pittsburg mine in the Pine Creek area of the Coeur d'Alene mining region near Kellogg , Idaho . The mine and mill have been operated successfully from 1942 to the present .

Feb 1, 1948

Provide a full-scale test facility where the effectiveness of all types of subsidence abatement techniques can be evaluated under controlled conditions. Background Subsidence is ground movement resulting from the collapse of overlying strata into a mine void because of failure of the mine roof, mine floor, or support pillars. The failure may propagate to the surface and be expressed as a depression, cracks, or a sinkhole. The surface expression of such features may be delayed until long after mining has been completed. Subsidence has the potential to affect more land area than any other type of abandoned mine land problem. Subsidence also causes direct damage to real property, with significant financial loss and more importantly, presents a danger to public health, safety, and general welfare. Subsidence-related problems are considered to be one of the most important abandoned mine land issues. Backfilling of mine voids is the most common stabilization method used to abate subsidence and protect surface structures. Backfilling or placement of material is performed by hydraulic flushing or pneumatic stowing, using either in-mine or remote methods. The majority of the past subsidence abatement projects has been performed using remote methods from single or multiple boreholes. Other subsidence abatement techniques arc available. For example, various point support methods are used to protect small areas of the land surface and surface structures, without completely filling the mine void. These may be more appropriate under different conditions. Little documented information is available concerning the capability of the various backfilling methods for completely filling a mine void or providing long-term structural strength. Therefore, the Bureau of Mines developed a laboratory for controlled evaluation of backfilling technologies.

Jan 1, 1991

By McHenry Mosier

The diamond-drill method was tried at the site selected for driving a 5- by 6 -foot air shaft at the east end of the Bellefonte mine . This method of sinking consisted , first , of drilling a 5-3/4 -inch-diameter cut hole from the surface , then drilling parallel 1.5 - inch ( EX ) holes around it at appropriate distances for a balanced blasting round . The cut hole was not charged with explosive but served as a relief chamber for the incipient expansion of the ground broken by. blasting the surrounding 1.5 - inch holes . The length of each hole was 236 feet , which was the finished depth of the shaft . The nature of the work in the air shaft was largely experimental , and many difficulties arising from the lack of special equipment and proper technique for precise alinement of the drill holes caused expensive delays before they could be overcome . Drilling the 5-3 /4 - inch hole , which was impeded by frequent core blocks in the core barrel , required 10 shifts . average advance per shift for an EX hole was about 150 feet . The The holes were charged and fired from the surface . The length of the section blasted in one cycle was 10 feet . Blasting progressed from the bottom of the shaft upward . The broken stone dropped into a chute , from which it was drawn into cars on the haulage level . The Bellefonte mine is an underground limestone mine.3/ The primary objective in undertaking the research on shaft sinking by diamond drilling was to perfect a method for driving connections between levels of the mine .

Oct 1, 1948

By R. D. Leitch

Tests have recently been conducted by the Bureau of wines on the ignition hazard of exposing heated filaments of electric mine lam bulbs in an explosive mixture of methane and air. This investigation was undertaken in order to settle a question that had arisen in connection with the safety of miners? electric lamps. For several years, in view of former studies made by the Bureau and reported in Bulletin 524, the fact that the heated filaments of even low voltage, lour candlepower bulbs constitute a danger was generally accepted by the Bureau's engineers. These early tests, as well as subsequent tests, were conducted with Pittsburgh natural was as the testing medium.

Jan 1, 1925

By Phyllip Worley, Frank E. Chase, Christopher Mark

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that “critical” sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

By D. K. Ingram, G. L. Mowrey, T. R. Rehak

Problem: Blasting is a hazardous component of surface mining. Serious injuries and fatalities result from improper judgement or practice during rock blasting. This paper describes several fatal injury case studies, analyzes causative factors, and emphasizes preventive measures. Method: This study examines publications by MSHA, USGS, and other authors. The primary source of information was MSHA’s injury-related publications. Results: During the 21-yearperiod from 1978 to 1998, the mean yearly explosive-related injuries (fatal and nonfatal) for surface coal mines was 8.86 (95% CI: 6.38 -11.33), and for surface metal/nonmetal mines 10.76(95% CI: 8.39 - 13.14). Flyrock and lack of blast area security accounted for 68.2% of these injuries. This paper reviews several case studies of fatal injuries. Case studies indicate that the causative factors for fatal injuries are primarily personal and task-related and to some extent environmental. A reduction in the annual injuries in surface coal mines was observed during the ten-year period of 1989 - 1998 [5.80 (95% CI: 2.71 - 8.89) compared to the previous ten-year period of 1979 - 1988 [10.90 (95% CI: 7.77 - 14.14)]. However, such reduction was not noticed in the metal/nonmetal sector, i.e., 9.30 (95% CI: 6.84 - 11.76) for the period 1989-1998compared with 11.00 (95% CI: 7.11 - 14.89) for the period 1979-1988. Discussion: A multifaceted injury prevention approach consisting of behavioral/educational, administrative/regulatory, and engineering interventions merits consideration. Impact on industry: The mining community, especially the blasters, will find useful information on causative factors and preventive measures to mitigate injuries due to flyrock and lack of blast area security in surface blasting. Discussion of case studies during safety meetings will help to mitigate fatal injuries and derive important payoffs in terms of lower risks and costs of injuries.

By R. R. Brown

The solubility and the activity of aluminum chloride hexahydrate, A1C13?6H2O, in aqueous solutions were determined as a part of the Bureau of Mines, U.S. Department of the Interior, research to improve mineral processing technology for recovering alumina from low-grade domestic resources. The solubility of A1C13 in pure water was found to be 31.09 and 31.77 wt-pct at 25° and 85° C, respectively, and decreased drastically to 10 and 0.1 wt-pct when the respective amounts of 20.3 and 37 wt-pct hydrochloric acid (HCI) were added in solution. The equilibrium constant for the solubility of hexahydrate, activities, and activity coefficients of A1C13 and H2O were calculated and compared with the results from the available methods of estimation. The results were shown to be useful in leaching nonbauxitic ores for extraction of alumina by changing the solubilities of component salts upon addition of HC1. Simultaneous solubilities of A1C13, FeC13, KC1, and NaC1 in solutions of HC1-H2O were also determined and their effects on the purity of A1C13?6H20 crystallized from mixed salt solutions are briefly discussed.

Jan 1, 1979

By G. J. Slavens

The Bureau of Mines has devised technology to recover cobalt, nickel, and byproduct copper from domestic lateritic material using an oxidative, ammoniacal ammonium sulfate leach. Nickel, cobalt, and copper were recovered by solvent extraction and electrowinning. To reduce the cost and complexity of cobalt recovery, an alternate method using lig-nite to extract Co3+ was investigated as reported herein. In the first 25 BV (bed volumes) of solution contacted with lignite, 97 wt pct of the Co3+ was extracted in & downflow column at pH 9.3. After 85 BV, the lignite was loaded to 1.5 wt pct Co3+ and further ex-traction was minimal. The lignite extracted cobaltic ammine complexes rather than cobalt ions and was nonselective as to other -metal cations and ammonium ions. Deleterious cations and 80 wt pct of the nonammine ammonium ions were removed prior to acid elution of the lignite. The removal of the ammines prior to elution to produce an ammonium-ion-freeCo3+ eluate was only partially successful. Thus Co3+ removal from ammoniacal solutions by lignite is technically difficult and economically unfeasible. It was also determined that reduction of Co3+ to Co2+ occurred during the extraction-elution process.

Jan 1, 1984

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, conducted a study of past mine explosions to identify the ignition locations and ignition sources responsible for the most severe explosion events resulting in death. Since the Scotia disaster of 1976, many fatalities from underground coal mine explosions have been linked to nonpermissible electrical equipment ignition sources located in intake air courses. With few exceptions, explosion protected equipment is generally not required in intake air courses of gassy underground coal mines in the US. Cigarette lighters were another prevalent ignition source for fatal explosions ignited in intake air courses. Several mine rescue/ recovery teams have encountered electrical ignition hazards. The study provides evidence that intake air courses of gassy underground coal mines fit the description of certain Hazardous (classified) locations described in the US National Electrical Code®. Class I Division 2 or Zone 2 explosion protection tech¬niques may be used to design intake air equipment so that it does not present an ignition source under normal operation, before mine power is shut down in emergency situations. Nonpermissible circuits in intake air courses that are likely to remain energized during emergencies, e.g. battery powered equipment, should be protected by more stringent Class I Division 1, Zone 1, or Zone 0 techniques, to protect rescue/recovery personnel.

Jan 1, 2009

By R. V. Higgins

This report presents the results of a study of gas injection in the Upper and Lower Terminal zones in fault block VB and in the Upper Terminal zone in fault block VI, Wilmington field, California. This report is based on data obtained to January 1956. Earlier studies of gas injection in other California fields have been reported .3/ The Upper and Lower Terminal zones, fault block VB, have been producing oil since 1945 and the Upper Terminal zone, fault block VI, since 1948. Before starting the gas-injection project, the expansion of dissolved gas was the principal mechanism moving the oil to the wells. Gravity drainage and an edgewater drive also have contributed to the movement of the oil to the wells. When the gas injection was begun, the reservoir pressure and the oil production had declined appreciably. Gas injection was started in the Upper and Lower Terminal zones, fault block VB, in May 1953 and in the Upper Terminal zone, fault block VI, in October 1953.

Jan 1, 1957

By William H. Pailes, Vincent Castronova, Daniel Lewis, Norman L. Lapp, George Goodman

"INTRODCJCTIONAlveolar macrophages are free lung cells located on the surface of small airways and alveoli. These phagocytes play an important role in the protection of the lung against airborne bacteria and particles.1 However, hyperactivation of pulmonary phagocytes can lead to excessive secretion of enzymes and reactive oxygen species which could result in lung injury, emphysema, or fibrosis.2,3 Analysis of bronchoalveolar lavage effluents for cell types and cellular activity has yielded information concerning the etiology of various pneumoconioses. For example, emphysema associated with inhalation of coal dust or cigarette smoke has been related to enhanced secretion of reactive oxygen species from alveolar macrophages.4-7 In contrast, hypoactivation of alveolar macrophages has been associated with inhalation of diesel particulates"" and has been related to increased susceptibility to pulmonary infection. s Inhalation of cotton dust has been associated with dramatic increases in lavagable polymorphonuclear leukocytes9 while pulmonary sarcoidosis and silicosis have been related with high numbers of lymphocytes in lavage effluentsl0,11The objective of the present study was to obtain lavage effluents from 8 control subjects, 8 healthy power plant workers exposed to fly ash, 1 healthy coal miner, and 1 rock driller with acute silicosis. These effluents were analyzed for total numbers of alveolar macrophages, lymphocytes and neutrophils and for secretory activity of alveolar macrophages. Data were then analyzed to determine what response patterns were characteristic for given dust exposures.METHODSSelection of SubjectsThe 8 control subjectS were all adult males from the area of Morgantown, WV. Two subjects among the controls had smoked cigarettes for approximately three pack-years and had stopped more than ten years ago. The 8 power plant :workers were all healthy adult male employees of a power facility in Hatfield, PA, approximately thirty miles from Morgantown. One of the power plant personnel was a comparable ex-smoker. The remaining subjects were all lifelong non-smokers. The coal miner was a healthy non-smoking male from Morgantown, WV. The rock driller was a patient under treatment with corticosteroids for acute silicosis. He had shown considerable clinical improvement with this treatment but still manifested significant radiologic and pulmonary functional abnonnalities at the time of lavage. The mean age of the 8 control subjects was 36 years (range: 31 to 49 years); the mean age of the remaining subjects studied was 38 years (range: 29 to 53 years)."

Jan 1, 1990

By Thomas F. Tomb

The penetration characteristics of a horizontal plate elutriator and of a 10-mm nylon cyclone were evaluated. The test aerosols were polydisperse coal-dust particles ranging from less than 0.3 to 15 micrometers in diameter. Particle densities ranged from 1.3 to 1.4 grams per cubic centimeter. Equivalent Stokes diameters were measured using Coulter counter analytical techniques. Experimental results indicate that the penetration characteristics of the horizontal plate elutriator closely approximate the sampling efficiency curve defining the respirable fraction of the dust cloud recommended and adopted by the Johannesburg Pneumoconiosis Conference in 1959. Penetration characteris-tics of the 10-mm cyclone were evaluated at flow rates of 1.4, 1.5, 2.0, 2.5, and 2.8 liters of air per minute. The data indicate that the penetration curve obtained at 2.0 liters per minute most closely approximates the sampling efficiency curve for respirable dust recommended at a meeting sponsored by the U.S. Atomic Energy Commission in 1961.

Jan 1, 1970

By R. Karl Zipf

MULSIM/NL (multiple scams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines and thin metalliferous veins. It can analyze one to four parallel seams that can have any orientation with respect to the Earth's surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) nonlinear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. Detailed checks show that numerical stress and displacement calculations compare well to known analytic solutions for simple problems. The total energy release calculated by MULSIM/NL is comprised of three basic terms: (1) strain energy release from the mined-out material, (2) linear kinetic energy release due to change in gravitational potential over the mined-out area, and (3) nonlinear kinetic energy release due to nonlinear materials in the total backfill and gob area. The strain energy release term is modified to account for nonlinear stress-strain behavior in the unmined materials. Comparisons of these numerical energy release rate calculations with known analytic solutions show excellent agreement.

Jan 1, 1992