Search Documents

By Philip W. Holland

This U.S. Bureau of Mines (USBM) report describes a chromatographic method that is used for rapid field determinations of carbon dioxide in natural gas streams at a USBM helium production facility. The method employs a commercially available portable gas chromatograph that is equipped with a 10-m fused-silica capillary column coated with a porous polymer. The instrument operating parameters permit determinations to be performed over a concentration range of 10 ppm to 10 pct with a frequency of 20 samples/h. The speed at which determinations can be performed is an important factor when evaluating efficiency or troubleshooting processes at the helium facility.

Jan 1, 1994

By Fred N. Kissell

Methane concentration peaks were measured by the Bureau of Mines at coal mine working faces during entry development. The statistical distribution of peaks was found to be normal or log normal depending on how well the methane was being mixed into the ventilation airstream. A normal distribution indicated good mixing, whereas a log-normal distribution indicated that mixing was poor. In addition, the "highest" peaks over selected intervals were found to fit a type I extreme-value distribution, a result similar to that obtained while mining longwall faces.

Jan 1, 1974

By A. F. Jolly

As a part of ongoing research into the sulfidation partitioning of selected complex minerals, the U.S. Bureau of Mines conducted research designed to selectively recover Cu from sulfidized chalcopyrite (CuFeS2). Ferric chloride (FeCI3) solutions leached >90 pct of the Cu and <20 pct (sometimes < 10 pct) of the Fe in the sulfidized concentrates. Cupric chloride (CuCI2) leaches were even more selective, solubilizing essentially 100 pct of the Cu and < 5 pct of the Fe. In contrast, leaching non-sulfidized CuFeS2 with either FeCl3 or CuCl2 showed that somewhat more Fe than Cu dissolved. These studies demonstrate that Cu is substantially more leachable from sulfidized CuFeS2 than from nonsulfidized CuFeS2? The Cu-and Fe-bearing constituents generated as sulfidation products, CuS (covellite) and FeS2 (pyrite), respectively, are differentially dissolved. The solubility of Fe from pyrite in sulfidized CuFeS2 is much lower than the solubility of Fe from complex nonsulfidized sulfide where Fe and Cu are bound in the same crystal lattice. Thus, the Cu dissolves selectively, producing a high-Cu filtrate from which Cu can be recovered by cementation or by electrolysis. Flotation of CuS-FeS2 mixtures indicates partitioned phases can be physically separated if effective liberation can be achieved. Magnetic separation tests yielded less promising results.

Jan 1, 1991

By G. R. Strimbeck

The Federal Bureau of Mines has been developing processes for producing synthesis gas directly from coal, oxygen, and superheated steam. An atmospheric-pressure pilot plant was constructed and operated to: 1. Determine the operability of the plant for gasifying coals of different ranks under various operating conditions. Listed in decreasing order of rank, these coals included a Pennsylvania anthracite, a bituminous A coal from the Sewickley bed, West Virginia, and a subbituminous C coal mined in the Lake de Smet region of Wyoming. 2. Determine the effect of varying operating conditions on: (a) Standard cubic feet (std.c.f.) of oxygen and pounds of coal of different rank required to make M std.c.f. of product gas (carbon monoxide plus hydrogen); (b) carbon gasified, percent; (c) exit-gas temperature, degrees F.; and (d) heat loss, B.t.u. per pound coal. 3. Compare the gasification characteristics, indicated in item 2, of coals of different rank: Bituminous A, anthracite, and subbiturninous C. 4. Determine the concentration of dust in the gases produced and the efficiency of dust removal, and investigate the relation between the sulfur content in the coals gasified and the gases produced.

Jan 1, 1960

By J. A. Lamonica

The Bureau of Mines studied two types of approved coal mine dust personal samplers to determine the effect of decreasing the amplitude of airflow velocity fluctuations on cyclone performance. Results indicate that more dust is collected when pulsation free flow is used. Velocity fluctuations were reduced by means of a pulsation damper; damper efficiency of about 85 percent was needed to reduce the fluctuations to an acceptable level. The data were obtained employing both pulsating and non-pulsating flow. A comparison was made of (1) the masses of respirable coal dust as determined by weighing and of (2) the particle size distributions as determined by an electronic counter. An empirical relationship is given between the ratio of masses collected using pulsating and nonpulsating flow (M&apos;) and the ratio of the maximum air velocity to the minimum air velocity (V&apos;) as measured in the cyclone entrance channel.

Jan 1, 1972

By A. T. Coumbe

During 1953-55, 31,105 miles of pipe for transporting crude petroleum and refined products was laid in the United States, a total slightly below that of the prior 3-year period, according to data compiled by the Bureau of Mines, United States Department of the Interior. The added mileage consisted of 22,571 miles of new pipe, representing about 2,163,807 tons of steel, plus 8,534 miles of secondhand pipe, equivalent to about 419,849 additional tons of steel. During the 3-year period, 13,069 miles of pipe was taken up. By January 1, 1956, the Nation had 188,540 miles of pipeline, an 11-percent gain over the 1952 total of 170,504 miles. The greater use of larger diameter pipelines indicated in recent surveys has continued, as the mileage for sizes 12 inches and over increased from 13 percent of the total mileage at the close of 1952 to 16 percent 3 years later. Crude-oil trunklines 12 inches and over in diameter gained 24 percent during 1953-55, and these larger lines represented 30 percent of the total mileage compared with 25 percent at the close of 1952. Furthermore, the mileage for crude-oil lines less than 12 inches in diameter declined 2 percent and made up only 70 percent of the 1955 total against 75 percent n the previous survey. Product Lines 8 inches and over increased 43 percent from 1952 through 1955 and composed 70 percent of the total mileage compared with 66 percent in 1952.

Jan 1, 1956

By G. E. McElroy

The Coeur d&apos;Alene minim, district of Shoshone County, Idaho, has been one of the largest and most active lead-silver producing districts in the United States for the last 40 years. The mines of the district enjoy exceptional natural advantages with respect to ventilation in that the veins apex high on mountain sides and are most often developed to considerable depths, up to 2,000 feet, by adit and crosscut tunnels under conditions that develop large natural draft pressures; the increase of temperature of the rock with increase of depth from surface in at a low rate; and the average surface temperatures are low. These natural conditions have, in the main, resulted in well-ventilated mines with low temperature conditions throughout. However, where the development has been carried to considerable depths below the lowest level of surface entry, natural-draft ventilation has proved inadequate, and mechanical ventilation systems have been installed on the three largest mines of the district. Local conditions, more particularly those in dead-ended working places, have also required auxiliary ventilation by will fan-pipe units in these and other mines. A particular feature of the district is the number of exceptionally long crosscut tunnels that have been driven to provide entry to vein systems from low points adjacent to milling and transporta¬tion facilities. Three of these tunnels are approximately 2 miles long, and lengths of 3,000 to 8,000 feet are quite common.

Jan 1, 1931

Objective To accurately measure very low air velocities (0-100 ft/min) in U.S. large-opening underground metal/nonmetal mines. Background Hundreds of metal/nonmetal underground mines operate throughout the United States. They extract commercial products from deposits such as limestone, salt, and gypsum. Mining generates a wide variety of gases and dusts, such as silica, diesel exhaust, radon, blasting byproducts, and perhaps even methane. If these substances become airborne, they can adversely affect the health and safety of underground workers. Many metal/nonmetal mines have large cross-sectional airways that could be 60 times larger than an average underground coal mine entry. These large airways require adequate volumes of fresh air to dilute, make harmless, and exhaust the toxic and, at times, explosive byproducts. However, in some underground mine sections, air movement is barely perceptible. The technology of measuring very low air velocities will become increasingly more important for operators of large-opening stone mines in order to monitor miner exposure to diesel particulate matter. Conventional anemometers (e.g., vane) are capable of accurately measuring air velocities only above 100 ft/min. Thus, it was necessary to investigate other anemometry technology to detect low air velocities in the range of 0-100 ft/min. Two different portable ultrasonic anemometers were tested. Actual testing was done in an underground limestone mine with openings about 51 ft wide by 29 ft high. Ultrasonic Anemometers Vane-type anemometers are commonly used by engineering personnel throughout the underground coal mine industry. They work well in measuring air velocities >100 ft/min. However, a separate technology, e.g., portable ultrasonics, is needed to measure air velocities much below 100 ft/min at various places within the large mine opening. Laser-doppler technology was also considered for this application, but was ruled out because of its high cost and other technical limitations. With no moving parts, the portable ultrasonic anemometers are claimed to be accurate down to about 1or 2 ft/min. The first type of ultrasonic anemometer that was examined underground is manufactured by Gill Instruments Ltd., Hampshire, U.K. The U.S. distributor is IN USA, Needham, MA. The Gill Instruments Solent Volometer (figure 1) is a battery-powered, single-axis anemometer meant for measuring low to medium air flows up to1,999 ft/min. It uses the ultrasonic "time of flight" principle where pulses of high-frequency sound are transmitted along the air flow path and the time taken to reach the receiver is measured. The faster the air speed, the quicker the pulses reach the receiver. The second ultrasonic anemometer that was examined under-ground is manufactured by Airflow Developments Ltd., Buckinghamshire, U.K. The U.S. distributor is Airflow Technical Products, Inc., Andover, NJ. The Anemosonic UA-6 (figure 2) is a battery-powered, handheld instrument with digital display. It measures air velocity (0 to 9,999 ft/min) or volume flow, flow turbulence intensity, and air temperature. Neither device is considered to be intrinsically safe for use in underground gassy coal mines. A comparison of salient specifications of both instruments is shown in table 1. The total suspended weight includes the instrument (Gill) or instrument probe (Airflow) plus about 35 ft of connecting cable attached to the pole. This combination of instrument plus cable length allows two operators to measure air velocities up to about 30 ft above the mine floor. Figures 1 and 2 show how each unit would be attached to an extensible, graduated fiberglass rod in order to position the sensor probe at a certain spatial point (centroid of the quadrate) within the underground large opening.

Jan 1, 2003

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Arkansas has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251 of which this is the tenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of which deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated. and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Arthur M. Hartstein

The Bureau of Mines through contract with Ultrasystems, Inc., obtained gram per gram data of products formed on thermal oxidative degradation of selected compositions, both under dynamic and static conditions. Four broad classes of materials were studied! Polyvinyl chloride compositions, neoprene compositions, rigid urethane foams, and variously treated woods. Whenever possible, comparisons between pure components and composites were attempted. Thermogravimetric and differential thermal analyses were performed to gain understanding of the processes occurring and to explore the feasibility of using these analyses as a method of material identification. The toxic products detected and quantitated included HC1, H2S, CO, S02, CS2,COS, HCOOH, CH3COOH, formaldehyde, acrolein, C 6H6, chloroprene, chloroethanol, benzyl chloride, aniline, and furfural.

Jan 1, 1974

By A. T. Coumbe, I. F. Avery

The Bureau of Mines has completed a survey of petroleum pipe - lines by direct correspondence with the oil companies and the use of the records of the Interstate Commerce Commission in order to cover both interstate and intrastate systems . The review shows that crude petroleum and product pipe -lines in the United States had a total length of 152,814 miles on January 1 , 1950 , an increase of 25,463 miles since May 1 , 1941 , the time of the last previous survey . The expansion in pipe -line systems was due largely to new trunk-line construction , as the mileage built to carry refined products increased by 11,880 miles , and those intended for crude -oil transportation gained 6,193 miles . Trunk lines represented 60 percent of all pipe -line mileage on January 1 , 1950 , compared with 58 percent in 1941 . The average diameter of trunk -lines for crude oil , as calculated on the various sizes and weighted according to their respective lengths , increased to 9.8 inches on January 1 , 1950 , compared with 8.4 inches on May 1 , 1941. The mileage for lines up to 8 inches used in crude trunklines has decreased since the 1941 survey , while those of larger sizes have increased . The extensive use of large- diameter oil pipe -lines has developed since the construction of two major lines from Texas to the East Coast at government expense as a World War II emergency measure . The successful operation of these lines proved their economic advantages over smallerdiameter lines as well as their effectiveness in moving unprecedented volumes of oil during the period when tanker movements were restricted by submarine action in the Atlantic Ocean . The 24-inch diameter " Big Inch " line carries over 300,000 barrels daily of crude oil , and the 20 -inch " Little Big Inch " carried over 230,000 barrels daily of gasoline and light fuel oils to destinations where they were urgently needed . Hence , Although these lines were sold and converted to natural -gas service in December 1946 , after fulfilling their wartime mission , their record proved to the industry that significantly lower operating and investment costs per barrel -mile of oil moved could be achieved than were possible with the comparatively small lines in general use up to that time . the several major oil pipe -line projects that have been constructed since the late war are of large diameter pipe . To assure supplies and market outlets of sufficient magnitude to support such lines and provide adequate flexibility , ownership is often shared by several large companies whose transport needs are served in common . The principal recent expansion in facilities has been from supply points in Southwestern States toward markets in the North and East and to Gulf tidewater .

Dec 1, 1950

By Walter R. Storms, Allan B. Bowman

This paper , which describes mining methods and practices at the Mineral Hill copper mine , is one of a series being prepared by the Division of Minerals of the Bureau of Mines on mining methods , practices , and costs in various mining districts. of the United States . The Mineral Hill mine is situated on the northeastern piedmont of the Sierrita Mountains at an altitude of 3,650 feet in sec . 35 , T. 16 S. , R. 12 E. , and sec . 2 , T. 17 S. , R. 12 E. , Pima mining district , Pima County , Ariz . ( fig . 1 ) . The claims (figs . 2 and 3) are in a gently rolling area with only scant desert vegetation . The average annual precipitation is about 11 inches . The nearest surface water is the Santa Cruz River , an intermittent stream 8 miles east of the mine . The property is owned by the Banner Mining Co. , a Nevada corporation . This report presents a brief history of the mine , describes the geology of the area and the ore deposits , outlines methods of prospecting and exploration , and gives methods of sampling and the estimation of ore reserves and values . Development and stoping methods are explained , and methods of underground transportation , ventilation , mine drainage , and safety measures are described . The concluding section of the paper is a section on milling . The Mineral Hill mine is an old mine that was reopened in 1951 after having been closed for 30 years .

May 1, 1957

By W. J. Fene

"The prevalence of accidents in the coal-mining industry has prompted a study of the workmen's compensation laws of the various States and the statistics of accident costs, for the purpose of explaining to operators how the compensation laws are regulated and to show the cost of accidents.The subject of compensation laws and accident costs is by no means new, but the prevalence of coal-mine accidents would indicate that the mine operator in general is not thoroughly conversant with their importance. Unquestionably, compensation laws are a large factor in promoting accident prevention, and it is believed that a greater measure of success would be accomplished in preventing accidents if all mine operators were fully aware of their important bearing on the cost of production.Many operators seem to be indifferent to accident occurrence; possibly they do not real¬ize the seriousness of the accident hazards that exist in their mines, even after the hazards are brought to their attention. There is no question that material financial advantages are to be gained by the prevention of accidents and it would appear that when these advantages are thoroughly understood, operators would be anxious to eliminate, insofar as is feasible, conditions likely to cause accidents.The unsettled state of the mineral industry and the irregular operation of mines during the past several years has probably been an important factor in influencing the apparently indifferent attitude of the operator. The chaotic conditions in the mining industry and especially in coal mining are unquestionably a factor that tends to increase accidents, just as mine idleness increases roof hazards and results in deterioration in mechanical, electrical, and haulage equipment, and promotes disorganization of the personnel. During such times greater efforts should be exerted toward the prevention of accidents because of these increased hazards and of the financial advantages brought about by the various savings to be effected when mine accidents are held to a minimum.This report on accidents in the coal mines of Pennsylvania was made possible largely through the cooperation of William J. Maguire, director, Bureau of Statistics, Pennsylvania Department of Labor and Industry, and Rush N. Hosier, superintendent, Coal Mine Section, Pennsylvania Compensation Rating and Inspection Bureau, who made available their records and extended much assistance and numerous courtesies during this study."

May 1, 1932

By H. V. Makar

Ferrous fractions recovered from urban refuse were tested by the U.S. Bureau of Mines, U.S. Department of the Interior, to assess their character, composition, and response to detinning. This research was conducted as part of the Bureau&apos;s efforts to conserve mineral resources through recycling. Results from laboratory and pilot tests established the technical feasibility of detinning scrap recovered from household refuse. Detinned products containing less than 0.03 percent residual tin were produced. Concentrations of other residual elements were determined and compared with those in existing commercial scrap and with proposed specifications. Studies were extended to include evaluations under commercial conditions. Preliminary tests on 5-1/2 short tons of ferrous fractions revealed the need for adequate shredding to assure optimum metal-caustic contact and minimize retention of tin-bearing rinse solution in the final baled product. The washed metal product contained 0.06 percent residual tin. Subsequent melt tests showed a yield of 91.4 percent. Based on these studies, full-scale commercial demonstrations showed that detinned bales equivalent to No. 1 bundle quality could be produced in carload quantities. Up to 5 pounds of tin per gross ton of scrap is con-currently recovered during the detinning process.

Jan 1, 1979

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the third. The data are accompanied by maps showing the location of holes drilled and deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township-map. The description of each half township is followed by a description of each deposit developed in that half township.

Jan 1, 1948

By Ronald S. Conti

Fire is a major concern for those who work in underground mines. A mine fire can occur at anytime and often results in a partial or total evacuation of mine personnel and could result in the loss of lives. Therefore, having a workforce that is well trained to prevent, detect, and fight a fire is important. This paper focuses on responders’ preparedness for fire. Responders in this context are considered the entire workforce and are categorized as first, second, and sustained responders and evacuating miners. Quality training enhances ones awareness of mine fire hazards and promotes self-confidence in combating fires and responding to emergencies. Early warning systems and other escapeway aids such as a through-the-earth signaling and communication system, lasers and strobe lights are also addressed. The technological advancements that have been made can improve the state-of-preparedness for responders to underground emergencies and increase the chances of survival for escaping personnel.

Minimize the risk of conveyor belt fires in underground coal mines by improving the accuracy of and means by which flammability data are acquired. Approach Develop a large, laboratory-scale flammability test for mine conveyor belting that realistically assesses its fire resistance. Background A conveyor belt fire in an underground coal mine is a serious threat to life and property. To minimize the risk of belt fires, the U.S. Code of Federal Regulations (CFR) for underground coal mines requires approved fire-resistant belting. Despite this precaution, about 25% of the reportable underground coal mine fires from 1983 through 1988 involved conveyor belting. In several instances, hundreds of feet of belting were destroyed. The current flammability test for fire-resistant belting is specified in 30 CFR, Part 18.65 and is conducted by (be Mine Safety and Health Administration (MSHA). The small-scale test is performed in a 21-in-cubical chamber with 6-in-long by 1/2-in-wide belt samples. To evaluate the flammability of conveyor belting under more realistic conditions, the U.S. Bureau of Mines conducted large-scale fire tests of belting. The large-scale data were then utilized in the development of an improved laboratory-scale flame test for fire-resistant belting.

Jan 1, 1991

By R. M. Winslow

"The phosphorus content of an iron ore is a determining factor as regards the value of the ore and also its metallurgical treatment. If some method of treatment, such as concentration, leaching, etc., could be used and the phosphorus con- tent of the ore reduced, it would be an important advancement in the iron mining industry towards the utilization of high phosphorus ores. Large bodies of material toe high in phosphorus to be marketable under present conditions would be made available, and a great deal of ore from the Cuyuna Range and other places, which is relatively high in phosphorus but otherwise suitable for making spiegel, could be reduced in phosphorus content sufficiently to permit its use in furnaces producing speigel.The form in which phosphorus occurs in iron ore is a much disputed question and it probably varies with the type and location of the ore. The statement has been made that ore piles on long exposure to the atmosphere often decrease in their phosphorus content. (Emmons, S.F. - Ore deposits, 1913, p. 652; Leith, C.K., Mesabi iron bearing district, U.S.G.S. Monograph 43, 1903, p. 275) There is described below experiments on the leaching of iron ores high in phosphorus, to determine whether it was economically possible to reduce the phosphorus content appreciably by leaching. As the research had a practical as well as a theoretical application, only low concentration of acids and alkalies were used.A number of variables were tried, among these being: (1) The solvent used, (2) strength of the solvent, (3) volume of solution used, (4) time ore was agitated (5) type of ore, and (6) screen size of the ore. The amount of ore taken was kept constant."

Jul 1, 1921

By J. M. Stuve

Low-temperature heat capacities of chiolite (Na5Al3F14) were determined by adiabatic calorimetry in the temperature range 5.8 to 300 K. The derived standard entropy (S°, 298.15) was 115.6 ± 0.2 cal/deg-mole. High temperature enthalpies relative to 298.15 K were obtained by precision drop calorimetry up to 1,000 K. Tables of experimental data and related thermodynamic functions are given for the temperature range of experimental observations.

Jan 1, 1980

By W. E. Miller, G. S. Scott, G. W. Jones

"INTRODUCTION One of the major activities of the Bureau of Mines is the promotion of safety in mining and the mineral industries. Research is undertaken in connection with these problems to determine the explosion and ignition hazards of combustible gases, liquids, and solids and to investigate means of reducing them.Occasionally the Bureau is asked to determine inflammability or ignition temperatures to enhance safety in nonrnineral industries. From time to time it has complied with such requests when no other agency was available to do the work and the investigation could be conducted with a minimum of time and expense. The present investigation is one of this class.Nicotine (C10H14N2), a colorless combustible liquid having a boiling point of 246°C, is usually obtained from tobacco and its products by extraction processes. When heated to its boiling point it decomposes; the purified product is obtained from tobacco extractions by distillation at reduced pressures or is distilled in a current of inert gas.It has an unpleasant odor, a burning taste, and in the undiluted state is highly toxic. Under certain conditions it can be oxidised to nicotinic acid and in the near future may therefore become of considerable economic importance. Nicotinic acid is a component of the vitamin B complex now commonly used to fortify white flour and other foods that normally are deficient in these vitamins."

May 1, 1942