Search Documents

By Mary H. Brown

The heats of formation of oxalic acid and sodium, potassium oxalates, and lithium oxalates were related by solution calorimetry to the heat of formation of (COOH)2.2H20, a value believed to be reliable as reported in the literature. The following heats of formation were determined: (COOH)2(a), -198.1±0.1; (COOH)2(ß), -197.8±0.1; UAW,, -328.7±0.4; Na2C204 -316.2±0.1; K2C204, -321.9±0.2; and K2C204-H20, -393.5±0.2 kcal/mole. The heat of the crystalline transformation (COOH)2(a) ? (COOH)2(ß) was determined to be 0.30±0.02 kcal/mole at 298.15° K.

Jan 1, 1970

By E. J. Gleim

This report describes a trip to Europe in the interest of safety in coal mines. It reviews the Eighth International Conference of Directors of Safety in Mines Re-search, which met in Dortmund-Derne, Germany, July 5-10, 1954, to discuss results of studies made in different countries to improve health and safety conditions under-ground. It also summarizes information on subjects of special interest in the United States gained by the writer in visits to mining experiment stations in Belgium, France, and England. The efforts being made to protect life and property underground were discussed, and ideas and experiences were interchanged freely, not only during the conference but also during visits to the several countries. Helpful information was obtained on many topics of interest, but time did not permit as thorough a discussion on some of them as might be desired.

Jan 1, 1956

By Linneas W. Laage

Coal production from underground coal mines has been important to the development of the industrial economy of the United States. Environmental problems have developed from some abandoned operations. These problems include: mine and refuse pile drainage, subsidence, unsafe mine openings and to a lesser extent mine gases, slope stabilities, mine and refuse pile fires and abandoned equipment and structures. Field investigations in three eastern coal mining districts, two in Ohio and one in Illinois, were performed to document the mine closure procedures used and subsequent problems that developed. The purpose was to identify, evaluate, and rank the seriousness of these problems. Based upon this evaluation, the undesirable present day situations could have been avoided or at least minimized by varying certain mining practices or mine closure procedures. It was found that federal regulations address all of these problems during the pre mining, active mining and post mining phases except for abandoned equipment which is the least threatening problem category. Ideally current practice would prevent future problems. However, the extensive and complicated nature of the legislation, environment and mining practices will necessitate adjustments to the law. The investigator recommends the following: 1) Goal oriented legislation encouraging complete resource extraction, standardization and compilation of mining generated hydrological data, periodic review of the coal mining regulations, and improved communication and cooperation between coal interests, regulators and the public. 2) Permitting effluent limitations to accurately reflect natural conditions. 3) Solidly back filling shafts and individual assessment of sealing or capping requirements. 4) Installing shaft vent pipes into the fill material to intercept and vent methane.

Jan 1, 1982

By R. V. Lundquist

The work described in this report, part of the Bureau of Mines long-range program to develop methods of utilizing submarginal domestic sources of aluminum, was undertaken to investigate the effects of iron in the lime soda sinter process, The approximate Fe2O3 content in a sinter for maximum alumina and soda recovery was 8 to 9 percent. Fe2O3 appears to inhibit gelation, and 15.5 percent Fe2O3 produces effects similar to those produced by 1 percent sucrose. In the lime soda sinter process, aluminum silicates are sintered with limestone and soda ash to yield dicalcium silicate and sodium aluminate. The sodium aluminate is extracted by leaching in caustic solution. The solution is purified by heating in an autoclave with lime to remove silica, and alumina trihydrate is precipitated with carbon dioxide. The reactions involved in sintering and leaching are complex. A number of studies by the Bureau of Mines4-9 and others1 indicate that the iron content of sinters influenced the recovery of alumina and soda and the gelation characteristics.

Jan 1, 1962

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1957 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1-6: Current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury experience: Tables 7-36: Current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employ¬ment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 37-41: Data on injuries, injury rates, employment, causes of injuries, and severity rates. (D) Major disasters: Table 42: Data on major disasters from 1948 to 1957. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 43-47: Data on fatalities and their causes at bituminous-coal, lignite, and anthracite mines from the earliest records through 1957.

Jan 1, 1960

By J. F. Barkley

"A knowledge of the carbon dioxide (002) content of the products of combustion, particularly from the boiler furnace, is very valuable. An instantaneous indication of the CO2 can be used as a useful guide to efficient burning. A permanent record over a. period of time gives a story to the management which tends to keep the operators more alert. Many instruments that indicate and record CO2 have appeared within the last fifteen years. More are about to appear. Although simple principles involving chemical, physical, or electrical qualities, are being used, there is at present a general feeling of uncertainty about such instruments in the boiler room any instruments are bought, run awhile, then lie idle indefinitely.Inquiries as to CO2 machines continually come to the Bureau of Mines from the general public, as well as from other branches of the Government. Some ten years ago a series of tests was made on certain instruments at that time on the market. The following test was made quite recently on four of the newer types, including one using an electrical principle. The four instruments were installed on one boiler each, according to the instructions of the makers, and the recommended routine attention was given them. The test was of a service nature duplicating the conditions under which the instruments ordinarily serve. The boiler that was available for this purpose was practically banked for some hours of the night. This caused the average CO2 for the entire twenty-four hours to be rather low, although it reached the higher ranges of the instruments during the day.Each day the charts were averaged and the results plotted to form the accompanying curve. The record of each instrument is shown by its particular mark, the dot, circle, cross and square being used in addition there is plotted for each day a rectangular area representing 1 % CO2 in height. The proper positions of this area was determined by means of the Crsat. Where the plotted point for an instrument falls within the rectangel its accuracy is within 1/2% CO2, which is considered satisfactory. Where it falls outside the rectangle, inaccuracy is indicated."

Mar 1, 1925

By Wilbur I. Duvall

This report presents experimental data on the propagation of explosion- generated strain pulses in rock. Tests were performed in 5 different rock types, employing 10 different types of explosives. Charge sizes ranged from 0.5 to 50 pounds, and travel distances ranged from 2.5 to 70 feet. Analysis of the data shows that the experimental peak strain data satisfy an exponential decay propagation law of the form: ?R/W1/3 = Ke ?aR/W1/3. For a particular rock, parameter K is a linear function of the calculated detonation pressure or the calculated energy density of the explosive. For a particular explosive, K is a linear function of the elastic parameter of the rock, p2, a result, which is at variance with elastic theory. The absorption constant, a, is independent of type of explosive but dependent upon rock type. However, no definite relation between a and the physical properties of the rock could be established.

Jan 1, 1959

By W. H. Herschel, E. W. Dean

"IntroductoryThe common practice of the petroleum industry is to measure viscosity by the use of instruments of the efflux or capillary tube type. The Saybolt universal viscosimeter has been tentatively adopted as a standard by the American Society for Testing Materials and is used extensively in the United States.Several instruments of foreign origin are also more or less familiar, such as the Redwood, the Engier, and the Baroey.Effina-type viscosimeters are well adapted to the ordinary needs of petroleum testing laberatories as they are simple and rugged in construction and away to manipulate, even in the hands of operators lacking scientific training. They have, however, certain limitations and for certain spacial types of work there are notable advantages incident to the use of the so-called torsion types of type of viacosimeter. The most satisfactory type of torsion viscosimeter now available in the market some to be that of MacMchael, which has been discussed in detail in a recent paper (Herschel, W. H., The MacMichael Torsional Viscosimeter. Jour. of Int. and Eng. Chem., vol. 12, 1920, pp. 282-286). The present paper indicates conditions under which this viscosimeter may be used to advantage in the petroleum laboratory, and outlines simple methods of operation and calibration."

Jan 1, 1921

To improve the reliability of the Bureau developed bore-hole gage now widely used to determine the absolute state of stress in rock. Approach Use the knowledge gained by extensive field tests to design a more rugged and reliable Instrument using lighter and stronger materials. How It Works The original gage consisted of a stainless steel cylinder 1-3/8 Inches In diameter and 10-1/2 inches long. The new gage is made from titanium. This lighter material reduces the weight of the gage by 43 percent, which enhances the gage placement and depth of overcoring in vertical up? holes. For added strength, the titanium case and placement end are now threaded to the gage body instead of using screw fasteners. Three pairs of strain gaged transducers are positioned to measure the diametral deformation of a 1-1/2 diameter borehole at 60-degree intervals around the Inner surface of the borehole. Each transducer consists of a beryllium copper cantilever with a strain gage cemented on each side. These transducers are secured Into the gage body by a tapered shank for minimal creep. The transducers opposite each other are wired together to form a 4-arm external bridge circuit. A pair of transducers is referred to as a component. Any deformation of the borehole, which occurs during overcoring, is detected by pistons which translate the motion to the components. Each

Jan 1, 1982

By H. Kim, R. W. Plummer, T. J. Stobbe

"The probability of developing coal workers' pneumoconiosis (CWP) varies among miners in different geographic areas, coal seams, and jobs. Many studies have revealed the correlation between mineral content and the frequency and severity of CWP development still remains controversial. Furthermore, the mineral content and its variability in different areas is unknown.Since mineral content is expected to vary from location to location within a mine, between mines, between coal seams, and over time, this information will be valuable in understanding the variations in CWP incidence, as well as in establishing the appropriate kinds of dust to use in toxicological research programs studying CWP.Size-selective airborne dust samples were collected using 4-stage cassette impactors at 9 different locations in each of five coal seams. These coal seams were the Upper Freeport, Pittsburgh, Kittaning, Coal Burg, and Pocahontas. Mineralogical analyses were done by a x-ray powder diffraction photographic technique.Common minerals found in coal mine dust were illite, calcite, kaolinite, quartz, siderite, dolomite, gypsum, anhydrite, and pyrite. The distribution of minerals in interand intra location samples will be reported. Early results on the mineral content show wide variations between locations.in a mine and between coal seams, and small, but significant, variations between particle sizes.INTRODUCTIONIn spite of its long history of incidence, and the large amount of research conducted on it, coal workers' pneumoconiosis (CWP) is still prevalent among coal miners and needs further research to develop effective preventive and remedial measures. Although the dose-response relationship between simple CWP and coal mine dust has been established (1), the causal agent(s) and the mechanism(s) involved in the progression of simple to complicated CWP are not yet defined. Many plausible hypotheses have been made to explain the mechanisms involved in the disease progression however none of them is satisfactory. In addition, the source of variation in occurrence of CWP among miners in different geographic areas (2), rank of coal seam (3,4), and job (5) remain unsolved."

Jan 1, 1988

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

By Irving Hartmann

When permissible explosives are used in coal mines according to the procedure recommended by the Bureau of Mines they are relatively safe, and no mine explosions are known to have resulted from this type of blasting. However, unsafe blasting practices - the use of nonpermissible explosives or the improper use of permissible explosives - have caused many serious disasters. In fact, such unsafe practices constitute the third most important cause (exceeded only by electricity and the use of open lights and smoking) of coal-mine explosions in the United States. During 1929-1947, inclusive, 81 explosions, resulting in 475 fatalities, were ascribed to unsafe blasting. The hazards of black powder, dynamite, and other nonpermissible explosives in coal mines have been recognized for many years, and attention has been called to this in numerous Bureau of Mines publications. Not only can these explosives ignite namable gas-air mixtures readily, but they can also ignite coal dust, as has been illustrated repeatedly in tests and at educational public demonstrations at Bruceton and elsewhere.

Jan 1, 1952

A Helix Pressure Gauge to Indicate roof bolt loads was designed, fabricated and field tested. The gauge indicated loads between 3,000 and 15,000 pounds with a ± ten per cent error. The coat of fabrication of the gauge was estimated to be $3.39 including an assumed overhead and profit per indicator for a series production of 5,000 unite. The unit can be read on a bolt to within ± 1,000 pounds load from a distance of twenty feet.

Jan 1, 1974

By N. A. Gokcen

Equilibrium partial pressures of gaseous HCl and H2O over aqueous binary and ternary solutions of HCl and AICls were calculated or estimated in the range of 20° to 110° C, and up to saturation with AlC13?6H2O. The results were extended to solutions containing less than 10 wt-pct FeCl3 by assuming that FeCl3 and AIC13 are equivalent on the molar basis, since both salts have trivalent cations with a cammon anion. The ionic activity coefficient of HCl and the equilibrium constant for dissolution of gaseous HCl were also computed. This research is part of the effort by the Bureau of Mines, U.S. Department of the Interior, to provide thermodynamic data to expand the technology base relevant to the extraction of alumina from nonbauxitic domestic raw materials.

Jan 1, 1980

Provide reasonably priced, reliable fire protection for front-end loaders. Approach Automatic fire sensing and suppression systems were developed and ruggedized for use on front-end loaders operating in harsh mine environments. How It Works Temperature sensors mounted in the loader's engine, transmission, and articulation areas detect the heat from a fire while it is still small and controllable. This triggers the release of the ABC class dry chemical extinguishing agent through a fixed piping system onto the fire. The system can also be manually activated from either the cab or ground level. Locations of the principal components of the system are shown in the drawing. Two control subsystems were designed to respond to varying fire protection needs and mine conditions. One subsystem only initiates discharge of the extinguishing agent. The other subsystem initiates visual and audible operator alarms if there is a fire sensed or if there is a fault in the control circuit.

Jan 1, 1979

By Launa Mallett, Michael J. Brnich

The first step to emergency preparedness is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen all at once. Risk assessments are used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. While the examples provided in this training package are specific to mine fires, the concepts and tools can be applied to any mine hazard. Purpose: This training package was developed to assist instructors, as they: 1) determine how to use risk assessment to improve preparedness for mine fire emergencies and 2) present risk assessment concepts and tools to trainees. Audience: This package is appropriate for workers/trainees from all types of mines. A risk analysis can be conducted by anyone familiar with the location(s) being studied. Why Conduct a Fire Risk Assessment? During a risk assessment, hazards are evaluated in terms of the likelihood that a problem may occur and the damage it might cause. Mine fire preparedness requires consideration of all possible fires that could occur. However, at a given mine some fires are more likely than others and some would result in greater damage than would others. Conducting a risk analysis identifies these differences. The results can be used to target resources at the types of fires that are most likely and/or are most destructive. Hazards that are very likely to result in fires that would do considerable damage to people and property should be targeted first for remediation and/or effective response if remediation isn't possible. Potential fires that are less likely or that would have less severe consequences are identified for attention later, after the more serious situations have been addressed.

Jan 10, 1992

By Alfred E. Schwaneke

An improved maximum-bubble-pressure system using the Sugden twin-capillary method for measuring the surface tension and density of molten metals is described. Improvements include (1) internally ground capillary tips, (2) electronic pressure transducers, (3) micrometer adjustment of immersion depth for density measurements, (4) valuing arrangements to allow operation at other than atmospheric pressure, (5) temperature range to 1,100° C, and (6) recorder readout of pressures. Data for surface tension of mercury from 20° to 300° C are given.

Jan 1, 1970

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A. 4 Illustrative Simulations The capabilities of the program are demonstrated by simulating various evacuation cases in different situations for a particular mine. The mine selected for the illustrative simulations is the mine I C' , as described in Section 2, chosen particularly because of availability of mine characteristic data and mine evacuation results for test drills. These evacuation results can be used to verify validity of the predictions made by the program A.4 1 Mine Characteristics A schematic diagram of the mine is shown in Figure 19. The figure shows all the major shafts, drifts, raises and stopes of the mine in the form of a network. There are four hoists, Hoist No. 1 and Hoist No. 2 are assumed to be single drum hoists and Hoists Nos. 3 and 4 form part of a double drum hoist, with Hoist No. 4 being the main hoist (master hoist) The positions of the 133 miners, typically working in a day shift of the mine, are also shown in the figure. The miners are identified by a miner number, and their total number on each level is chosen from the data on the fire drill simulated as Case No. 1 in the illustrative simulations.

Jan 1, 1976

By Alan R. Buehler

The Bureau of Mines conducted a mineral investigation of the 32,270-hectare Cache Peak study area in 1992; the area had been proposed as wilderness. Bureau personnel examined and sampled prospect workings; 50 rock and placer samples were taken during the investigation. The study area is centered about 25 km southeast of Challis, Idaho, in the Challis National Forest. According to May, 1993, Bureau of Land Management mining claim records there were no current mining claims located inside the study area. Up to 100 claims may have been located in the study area in the past. Gold, silver, copper, lead, zinc: Significant analyses, poor exposure precludes resource estimate. Limestone: More than I billion tonnes may be chemically suitable for a variety of uses, markets too distant to favor mining. Dolomite: More than 1 billion tonnes may be chemically suitable for producing magnesium metal, markets too distant to favor mining. Sand and Gravel: Several million m3, but markets and transportation costs do not favor mining. Chalcedonic nodules: Two localities in the study area may be of interest to hobbyists who cut and polish stone. There is no reported past production from the study area.

Jan 1, 1993