Search Documents

By E. D. Calvert

As part of its goal to minimize the requirements for critical and strategic minerals, the Bureau of Mines is conducting research to foster the use of domestically abundant materials such as molybdenum. This report describes the development of an investment shell molding technique that can be used to make castings of molybdenum and its alloys. The mold material is cubic Zr02 with a monoclinic Zr02 binder. The shell, formed by standard investment molding techniques described in the text, is prepared for molybdenum casting by firing for 6 hours at 1,550° C (2,822° F) or for 4 hours at 1,650° C (3,002° F). The resulting castings have predictable and reproducible dimensions with good detail. As-cast strength is poorer than the strength of wrought materials below 1,600° F. At and above this temperature, tensile strengths of cast and wrought materials are nearly equal. Aqueous corrosion of the castings in most media is insignificant.

Jan 1, 1982

By Richard J. Mahany, Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission in metal/non-metal mines over a wide frequency range from 0.2 - 1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types include oil shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most important mining techniques. The results show that transmission at medium frequencies are optimum for wireless mine communications, in agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 8, 1981

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987

By William J. Campbell

The Federal Bureau of Mines provided five test materials--amosite, short-and long-fiber chrysotile, crocidolite, and nonfibrous tremo1ite--to the National Institute of Environmental Health Sciences (NIEHS) for studies on the biological effects of orally ingested asbestos-related materials. An inter-agency agreement between the Bureau and NIEHS made possible this program to characterize these test materials. The Bureau in turn received support through contracts with the Ontario Research Foundation for the milling of amosite and crocidolite, and with the University of Maryland for microscopic measurements. The five test materials, which were supplied in quantities of 960 to 1,200 pounds each, were characterized by chemical-instrumental analysis for elemental composition, surface area, density, X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, mineralogy, and particle size analyses. Particle size distributions were emphasized because of the current theories relating adverse biological effects to length-width characteristics of durable elongated particles.

Jan 1, 1980

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

4. Preliminary Study - Remote Seal Checker 4.1 Introduction Determination of the completeness of each individual seal at the time of its emplacement is essential for an effective remote sealing system. A satisfactory seal checking technique should provide a signal which: (1) indicates percentage completion as the seal is emplaced (2) provides a definite indication of a complete seal (3) indicates the size of the unsealed area if a complete seal is not feasible This information is required to establish the need for additional seal material, the need for additional seals, and the risk likely involved in entering the mine., In many situations it is as important to know the quality of a seal as it is to build an effective one. It is likely that with repeated use the remote sealing technique developed by Foster-Miller Associates will be sufficiently reliable and predictable to preclude the seal checking requirement. It is recommended, however, that each seal be checked during construction to insure its completeness and increase the level of confidence so necessary in reopening the mine. 4.2 Description of General Problem Several characteristics of remote mine seals are important in considering techniques for evaluating the effectiveness of these seals. These include:

Jan 1, 1973

By W. E. Miller, W. P. Yant, G. W. Jones, R. E. Kennedy

"The determinations of the limits of inflamability of diethyl ether and ethylene in air described in this report were made primarily for comparison with similar determination of other compounds in the same apparatus and by the same laboratory technic. The experimental procedure and the results obtained differ somewhat from those of other investigations. The work also included determinations of the limits of inflamability of these combustibles in oxygen The investigation,was conducted at the Pittsburgh Experiment Station of the United States Bureau of Mines in cooperation with Merck & Co., Inc. LIMITS OF IMFLAMIABILITY OF DIETHYL ETHER-AIR MIXTURESThe limits of inflamability if diethyl ether in air were determined for upward propagation of flame in an upright, closed 8-liter, cylindrical iron bomb 10.2 cm in inside diameter and 96.5 cm in length. This bomb been described in a previous publication. 6Two brands of diethyl ether were used, one a C. P. sulphuric ether manufactured by Baker & Adamson, and,the other Merck & Co. product manufactured for anaesthesia and containing about 3.5 percent of ether alcohol."

Jul 1, 1935

By Zachary J. Fink

A continuous-monitoring system has been developed for analyses of mine gas concentrations associated with spontaneous combustion, mine fires, and explosive and toxic levels. The analysis center, which is linked to sample locations by polyethylene tubes in bundles, has been successfully field tested by the Federal Bureau of Mines for analyzing carbon monoxide and oxygen; a computational scheme has been developed to process the data at the site. This report contains information on the design, purchase, installation, and maintenance of the tube-bundle system. A brief comparison of the tube-bundle system with the underground-analysis system and plans for future research are also included.

Jan 1, 1975

By E. V. Cilento, K. A. DiGregorlo, R. C. Lantz

A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared to experimental results obtained from single rat PAM. The O2 - was quantified by measuring the reduction of nitroblue tetrazolium (NBT) to a diformazan precipitate (NBTH2) from video-recorded images of individual cells. The kinetic model considered three reactions: (1) the production of extracellular 0 - from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, (2) the subsequent dismutation of o2- to from O2 , and (3) the reaction of o2- and NBT. NBT specificity for o2- was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) which catalyzes the dismutation of o2- to H2o2. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations since NBT is a relatively small molecule (818 MW) compared to SOD (34000 MW). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/or electrostatic effects since SOD is also negatively charged.

Jan 1, 1988

By John A. Richards

This paper is one of a series being published by the Bureau of Mines on mining methods and costs. It describes briefly the manner in which slusher hoists and scrapers are used in connection with clock-caving methods at the Emma Nevada mine of the Consolidated Coppermines Corporation, Kimberly, Nev. Kimberly is in the Robinson mining district, White Pine County, 7 miles west of Ely. The district is served by the Nevada Northern -Railroad, which branches from the main line of the Southern Pacific at Wells, Nev., 140 miles north, Paved U. S. Highway 50 from Salt Lake City, Utah, to Reno, Nev., passes through Ely. The altitude at the collar of the Emma Nevada shaft is 7117 feet. The surrounding hills are covered with a sparse growth of juniper, pinon, and mountain mahogany.

Jan 1, 1940

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining (1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and (3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979

Develop a more efficient method of testing the integrity of in-situ leach mining operations. The Problems For economic and environ-mental reasons, in-situ leaching operations must be sure that wells do not leak. Loss of solution in large quantities can be expensive in itself, and if such losses result in pollution the costs can be even higher. Wells are usually tested for leaks by sealing them with packers, pressurizing them and monitoring the pressure drop. However, many commercially-available packers are designed to be used in steel-cased wells rather than the fiberglass-or plastic-cased wells used for in-situ mining. These packers are heavy, cumbersome, expensive, and often leak. In addition, commonly used well-integrity-test systems require lengthy test periods and drill rigs or hoist trucks with rigid pipes must be used to run the packers in and out of the well. The Bureau of Mines has developed a mobile, self-contained leak-testing system that is faster, uses trailer-mounted equipment that can be operated by one person, and features a new inflatable packer.

Jan 1, 1985

By Samuel P. Harteis, Eric S. Weiss

The National Mining Association and the Mine Safety and Health Administration requested that the National Institute for Occupational Safety and Health (NIOSH) conduct full-scale evaluations of a recently developed carbon fiber-reinforced polymer (CFRP) reinforcement technique for upgrading existing mine ventilation seals to withstand an explosion pressure of 50 psi or greater. The evaluation was conducted in the NIOSH Pittsburgh Research Laboratory’s Lake Lynn Experimental Mine (LLEM) near Fairchance, PA. The purpose of the evaluation was to determine the blast resistance of the CFRP reinforcement technique, designed to increase the strength of two types of existing 20-psi-rated in situ mine ventilation seals. Two candidate ventilation seals were selected to represent the 20-psi alternative seal designs typical of those used in mines prior to July 2006. Installed within the LLEM were (1) a 4-ft-thick pumpable cementitious foam seal using material with a designed 150- to 200-psi average compressive strength at 28 days and (2) a 24-in-thick, low-density cementitious block seal with a center pilaster and keyed to the floor and ribs. The materials necessary for the CFRP reinforcement technique were then installed on the outby (active) side of each seal, and the seals were subjected to explosion overpressures. Both seals with the CFRP reinforcement retrofit successfully withstood explosion pressures of 60 psi or greater during the full-scale evaluations in the LLEM.

Jan 1, 2008

By John Ward Smith

Methods for estimating the amounts of nahcolite, dawsonite, and the sum of these two sodium carbonate minerals from oil-yield assay data are developed and evaluated for Green River Formation oil shales from the saline section of Colorado's Piceance Creek Basin. Derived statistically, these estimation methods depend on the fact that these minerals yield water and gas measured during oil-yield assay. The estimation procedures yield values for nahcolite and nahcolite-plus-dawsonite of sufficient accuracy for stratigraphic plotting and correlation, whereas estimates for dawsonite are more generalized. However, resource estimates and reserve computations for both nahcolite and dawsonite accurate within 10 percent of the real value are readily available by summing the mineral amounts calculated by the procedures presented. These estimation procedures are applicable to oil-yield assay data on core samples from more than 30 coreholes which have penetrated the saline section of the Green River Formation in Colorado.

Jan 1, 1972

By John Henderson

If you missed this year?s Texas State Holmes Safety Association meeting, you missed a great one. On January 23 & 24, 2009, we held the meeting that was rescheduled when Hurricane Ike threatened Corpus Christi in September 2008. Sixty-five persons from across the state attended the meeting held at the Holiday Inn Emerald Beach. The weather was 82 degrees, and the sky was clear and perfect for a safety meeting. Evaluations submitted by the attendees gave the presentations, the networking, and even the food top marks. There were eight councils represented; Big Country, Central Texas, Costal Bend, Heart of Texas, Hill Country, North Texas and North Central. Presentations included Workplace Examinations, Emergency Preparedness, Screen Safety, Contractor Responsibilities, Powered Haulage, Supervising for Safety, and Basic Inspections of Slings and Rigging. Mr. Edward Lopez, SC MSHA District Manager, gave the State of the District Address.

Feb 1, 2009

By D. E. Hirsch

The Bureau of Mines has developed a systematic procedure for separation, characterization, and semiquantitative analysis of high-boiling (350° to 550° C) distillates of crude oils. Isothermal and molecular distillation were used to prepare the 370° to 530° C distillate of Recluse, Wyo., crude oil. The distillate was separated into fractions by chemical treatment, silica-alumina gel adsorption, and gel permeation chromatography (GPC). The fractions were analyzed by use of GPC correlations and mass and nuclear magnetic resonance (NMR) spectrometry. The increased knowledge of petroleum composition obtained from the data will contribute to improved petroleum processing and utilization and energy conservation.

Jan 1, 1974

By S. R. B. Cooke, F. D. DeVaney

"INTRODUCTION The potash mineral receiving the most attention in the newly discovered. New Mexico-Texas potash district near Carlsbad, N. M. is sylvite (potassium chloride). Sylvite contains more potassium than any other mineral. Merchantable high-grade deposits have been found, and those of lower grade may be enriched to a high degree of purity by refining methods. Deposits containing sylvite were the first to be developed and axe the only ones being mined.However, many other minerals that contain potash occur in the salt beds of the Carlsbad District. Of these the more important are polyhalite, carnallite, langbeinite, leonite, and kainite. The nature of the deposits and their mineralogy have been described in detail by members of the United States Geological Survey. 4/Langbeinite, although not so abundant in these deposits as carnallite and has particular interest because the potash is in the form of the sulphate and as such commands a premium in terms of K20 unit. This is explained by Fox and Turrentine 5/, who state:"

Feb 1, 1936

By Louis C. Brichta

This report summarizes the progress made by the Federal Bureau of Mines in assembling and compiling a catalog of available logs of drill holes and maps of mine developments in the Tri-State Zinc-Lead District in northeastern Oklahoma, southeastern Kansas, and southwestern Missouri. It supplements an interim report (11)3/ published in 1955, and for convenience of the reader repeats much of the general descriptive matter pertinent to the district contained in that report. The work of procuring and recording the data was begun in August 1949 and was recessed in May 1959. The catalog preserves the records of accomplished explorations and mine developments in the district and provides a readily available source of information for individuals and firms interested in planning mineral explorations, Government agencies estimating of reserves of mineral resources, and the mining industry for general use.

Jan 1, 1960

By Jon C. Volkwein

Advances in mining technology have enabled deeper seams of coal to be mined from the surface. Highwall mining is frequently used to mine areas at the perimeters of a surface mine when removal of the overburden becomes uneconomical or threatens environmentally sensitive surface features. At the same time, advances in materials and technology have enabled highwall mining of coal that create blind headings over 300 meters in length. Deeper surface mining and deeper highwall penetration depths have lead to more frequent encounters with methane gas. While this coal is remotely mined from the surface, underground ignitions of methane have propagated to the surface and injured miners. Methods described in this paper show how this hazard can be correctly monitored and controlled for auger type highwall mining machines. Research indicates that small quantities of gas liberated during mining migrate to the face, creating higher gas concentrations than would otherwise be expected. Using the same principles that cause the gas to migrate to the face, researchers have shown that inert gas introduced at the collar of the hole can inert the entire hole, thus ensuring safe conditions for mining.

By Lester G. Morrel

THE RICH and varied occurrences of metallic ores in Australia, extensive nickel deposits on New Caledonia and phosphate rock on several widely scattered small islands were important aspects of the economy of the South Pacific area. Relatively small quantities of gold and nonmetallic minerals produced in New Zealand, Fiji, and the Territory of Papua-New Guinea remained important to the domestic economies of these islands, but had little importance to overall world mineral supplies. The value of mineral commodities produced in this area in 1964 was estimated at $658 million,3 compared with $585 million in 1963. The year's greatest commodity gains were in bauxite and aluminum, beryl concentrate, manganese ore, nickel smelter products, tin, and coal. Annual increases were recorded in virtually all countries and possessions in the area except Papua-New Guinea, where the drop in output of alluvial gold accounted for a decline of about $160,000. Mineral industry activities in Australia overshadowed those in all other parts of the South Pacific in 1964. Outstanding developments were the sales contract negotiations and physical preparation for exploiting the rich iron ore discoveries in Western Australia, the initiation of domestic crude oil production, the commissioning of two new steal mills and an alumina refinery and a start on the new alumina-aluminum project based on Cape fork bauxite deposits. The principal mineral development in 1864 in New Zealand was the progress on plans of the Newzealand Steel Co. to use indigenous iron sans as the resource base for a local steel industry. In New Caledonia, additions and expansion of the nickel mining and smelting facilities continued throughout the year. Plans for extensive geophysical studies were announced by the Government Geological Departments of British Solomon Islands and Fiji.

Jan 1, 1966

By William A. Beck

"The Old Cline mine, also known as the Old Cruse mine, was first worked for gold in1895. The property was opened by several shafts and trenches; and some stoping has been done, producing several cars of copper-gold ore in the early nineteen hundreds. Chalcopyrite is visible in selected samples; and, with the aid of a mineralite, several samples showing a considerable amount of scheelite were found on the old waste dumps.The mine is in Township 6, Cabarrus County, N. C., 5 miles north of the village of Mount Pleasant, 10 miles northeast of Concord, and about one-half mile south of Watts Crossroads. It is one-fourth mile east of the county road.When examined, the property was owned by H. F. Tompkinson, Concord, N. C., and was leased, with option to buy, by L. Nash. Titles of record were not investigated.As stated above, the Cline mine was first worked in 1895. The property was Purchased in 1902 by J. A. Clark and A. A. Smith of Atlanta, Ga., and worked for gold and copper. No record is available of the quantity of ore removed during these operations.A Bureau of Mines mining engineer3/ examined the mine as, a copper prospect on October 13, 1944.The Cline mine is in an area characterized by flat to rolling topography, dissected by many streams and rivers. It lies in the Piedmont Plateau and Varies in elevation from 700 feet to 800 feet. The surrounding country is partly wooded and partly cleared farm land.A quartz vein occurs in country rock of quartzite and greenstone.4./ The ore occurs in a series of quartz lenses, having a width of 1 to 3 feet and dipping about 750 NE, and striking N. 300 W. All these lenses have fairly sharp boundaries and in some cases are entirely separated from each other, while at other times they are connected by thin stringers of quartz. They can be traced for 1,000 to 1,200 feet by a series of shafts and test pits."

Apr 1, 1946