Search Documents

By Alton B. Cook

Data are presented to show oil vaporization resulting from the passage of natural gas through a sand-packed tube saturated with synthetic reservoir oils. The Bureau of Mines performed 13 experiments, using reservoir oils synthesized with base crude oils of approximately 22°, 35°, and 45° API, at 100°, 175°, or 250° F and 1,100, 2,600, or 4,100 psia. It has been determined that the amount of vaporization is significant if proper conditions exist. These experiments show that oil vaporization depends on pressure, temperature, volatility of the oil, and amount of gas cycled. Increases in each of these conditions increase the volume of oil vaporized.

Jan 1, 1969

By L. C. IlsLey

"The maintenance of permissible equipment which is tested and inspected at the Pittsburgh Experiment Station of the United States Bureau of Mines is dependent to a surprisng degree upon the voltage at which the equipment is operated. The difficulty of maintaining 500-volt equipment is frequently brought to the bureau's attention, and it is quite possible that if the bureau had appreciated at the beginning the full hazard involved, it would never have undertaken the approval of equipment operating at voltages greater than 250 volts.In this connection, the following statement from State mine inspection departments and other sources are of interest as showing the general feeling in safety organizations with respect to voltages higher than 250. These statements, although obtained as a result of a questionnaire sent cut several years ago, still apply very well to present conditions.A. I have not had time to consider seriously the proposed change from every angle, but looking at it from a standpoint of hazard, feel that the danger would be greatly increased. I have always occupied the position that underground voltage on portable equipment should never exceed 250 volts.High voltage of course would mean smaller transmission lines, which would be more economical and no doubt would require in several instances smaller equipment; notwithstanding, if this statement is true, the writer is still favorable to low voltage on underground portable equipment.B. I believe 500 volts should be the limit on the best equipment ender the best conditions and that the U. S. Bureau of Mines should do all in its power to limit the voltage to 500 volts on permissible equipment, as any increase in voltage means increased hazard.C. I will refer you to a section of our mining law, entitled ""An Act to Regulate the Tine of Electricity in the Mines of the State of ----"" which reads in part, as follows: Trolley wires, or other exposed electrical wires, shall not carry a voltage above 275 volts.You may readily see by this that we are not permitted to operate mining machines under ground in -----, with more than 275 volts at the terminals, except that we are permitted to install transforming stations throughout the mines, after complying with certain regulations at the mine.However, as we have had to date, within the calendar year of 1925, six men electrocuted in the mines of the State, using a voltage of 275 volts, I am of the opinion that if this voltage was increased, the hazard would also be increased in proportion.D. I do not care to make a statement for publication: however, I am referring you to our mining laws. On page 27 and 28 you will find what the laws of -----¬require relative to the installation of electricity in the mines.""Hereafter where electricity is installed no higher than two hundred seventy-five (275) volts shall be used underground, except for transmission, or for application to transformers or other apparata, where the high-voltage circuit is stationary. High-voltage motors, and transformers, shall be installed in suitable chambers, built of fire-proof construction, and well ventilated, and shall not be placed on intake, or between intake and return air courses. All high-voltage lines lines and apparata must be clearly marked, to indicate their danger. Main and distribution switchboards for high voltage shall be made of insulating and incombustible material, such as marble or slate, and to be free of all metallic veins, or of material equivalent thereto. Same shall be installed in a dry place. All switches or other instruments used in connection with high voltage shall be installed on suitable switchboards, with at least a three-foot passageway in front and rear properly floored, and kept looked by a door at each end that can be opened from the inside without a key. With higher than medium voltage, there shall not be any live metal work on the front of switchboard, and the entry circuit must be protected by an oil breaker s"

Apr 1, 1932

By R. V. Ramani, P. M. T. White, D. Sutton

1.1 General The examination and evaluation of a mineral deposit to determine whether or not it can be profitably exploited entails many factors unrelated to the physical nature and intrinsic worth of that deposit. Nevertheless, geology and geologically related factors have great bearing on the economic potential of the deposit. This is only natural because the deposit owes its existence to these factors. This is even more so in underground mines where the whole system is a geologically enclosed one. Geology plays a major role in at least four phases of a mineral venture. Firstly, it acts as an indicator of the existence of parti¬cular minerals. For example, it is inconceivable that a sedimentary coal deposit would exist in a granitic batholith or stock, or that a sandstone would host primary copper or nickel sulphides. Further, the positional relationship of different rock types may be significant in locating deposits such as replacement zinc and copper sulphides in limestones which have been intruded by igneous rocks. Thus, geology is important in the exploration phase of a mineral deposit. Secondly, once potentially valuable minerals have been discovered, knowledge of geology plays a significant role in determining the dis¬tribution, grade and extent of the mineralization. Controls on mineralization include one or all of those related to structure, rock type, sedimentary features, post-depositional redistribution, etc. Con¬sequently, in order to effectively evaluate a deposit in terms of

Jan 1, 1974

By G. S. Rice

This paper describes preliminary tests at the Bureau's Experimental Mine to determine, under conditions that may prevail in a bituminous coal-mine heading, how small a quantity of fire damp may bring coal-dust into suspension and ignite it. The results show that the explosion of as little as 150 cubic feet of an explosive mixture of gas and air containing 9 per cent natural gas may start a disastrous explosion of coal-dust. This is a very small volume, of gas, to cause such a result. Let us suppose that this amount of explosive mixture, as at the face of an entry which was 10 feet wide and the face was overcut to a depth of 6 feet and an upper layer of coal 2.5 feet thick had been removed, the recess so made would have a volume of 150 cubic feet. Furthermore, only 13 cubic feet of pure methane is needed in thin volume to produce this 9 per cent explosive mixture.

Jan 1, 1930

By George S. Rice, C. W. Owings

"Brattice cloth is an important material in coal-mine ventilation practically all coal mines use some brattice cloth, gassy mines a large amount. It is employed in three ways:Crosscut brattices.Curtains in haulageways.Line brattices in gassy mines.In each case brattice cloth is used to deflect part or all of a split of the mine ventilating current into or toward the face of a working place. As a general rule, its use in a particular location is temporary.A crosscut brattice should be employed only until a permanent stopping has been erected. Such a brattice is subject to little wear when in actual service, the chief damage occurring when it is taken down and put up again.When used for curtains on haulageways or haulage crosscuts to deflect the air current up into rooms or headings, the wear on brattice cloth is considerable, as mine cars, machines, and personnel constantly pass under the curtains which last only a few days or a few weeks in an active part of the mine. For such purposes tightly woven smooth cloth is desirable, so that it will not be easily torn. Curtains should not be used back from the working places, as they sometimes are, to deflect the main. split, as the leakage of air is too great. Doors should be used in such places."

May 1, 1928

By Alan R. Buehler

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 256,430-acre Alvord Desert and part of the 22,240-acre East Alvord Wilderness Study Area (OR-002-074 and OR-002-073A, respectively), in order to evaluate their identified mineral resources. The study areas are located in Harney and Malheur Counties, OR, about 25 mi northeast of the small village of Fields. There are no mines, prospects, or identified mineral resources inside the study areas. Basalt flows within the study areas contain chalcedony-lined vugs and banded agate which may be of interest to rock hounds. An ignimbrite flow contains perlitic material, but crystalline contaminants make it unsuitable for commercial uses. Lacustrine (lake) sediments contain diatomite and clays, and evaporite crusts contain boron too low grade to profitably mine. Small quantities of common opal and petrified wood occur which might be of possible interest to rock hounds. Some of the petrified wood is black, free of fractures, and polishes well; it may be suitable as backing material for soft, thin, and brittle gemstones, such as precious opal. The lacustrine sediments also contain black, fetid layers which have above background, but economically insignificant concentrations of zinc, cobalt, nickel, barium, iron, manganese, aluminum, and potassium. Large quantities of fine-grained dune sands within the study areas are too far from markets for economic consideration. Ephemeral streams in the study areas contain small amounts of placer gold of no economic interest. The western portions of both study areas are reported to have moderate favorability for occurrences of natural gas, and both study areas are reported to have high favorability for the occurrence of geothermal resources. As of December 1986, oil and gas leases covered 3,100 acres in the study areas.

Jan 1, 1987

By L. D. Tracy

"This paper represents work conducted by the Bureau of Mines in cooperation with the Illinois Geological Survey and the Engineering Experiment Station of the University of Illinois.IntroductionThe present report covers conditions and mining royalties in District VIII of the coal fields of Illinois, as designated by the Illinois Geological Survey. The various districts have been described in the reports on the Illinois coal-mining investigations, carried on cooperatively by the Illinois Geological Survey, the engineering experiment station of the University of Illinois, and the U. S. Bureau of Mines. This district includes Vermilion and Edgar Counties, but as the coal-mining operations in Edgar County amounted to only 827 tons in 1923, the data here given have been confined to Vermilion County.A similar report on District VI (Williamson and Franklin Counties) has been issued as Serial 2722 of the Bureau of Minos.A description of geological and mining conditions, and a discussion of market and transportation facilities, have been included because these have an important bearing on the royalties specified and the general conditions of the lease.Mining ConditionsDistrict VIII is better known as the Danville district and in 1923 produced 4,177,000 tons of coal, or approximately L per cent of the total output for the entire State for that year, which was 79,300,000 tons."

Apr 1, 1926

By David Schlain

This Bureau of Mines report describes a method for electrodepositing titanium diboride from a molten salt bath. Initially, the electrolyte is a mixture of LiBO2, NaB02, Na2 Ti03 , Li2Ti03, and Ti02? The cell is operated at 900° C in a dry, inert atmosphere with consumable anodes of titanium or hot-pressed titanium diboride (TiB2) powder. Agitation of the electrolyte is essential. Current densities may be 6 to 9 amperes per square decimeter (amp/dm2) with titanium anodes and 9 to 30 amp/dm2 with titanium diboride anodes. A current density of 6 amp/dm2 is equivalent to a plating rate of about 35 micrometers per hour. The adherence of the TiB2 deposit varies with the substrate material. It is most adherent on molybdenum and on 4130 steel that has been preplated with copper and nickel, less adherent on nickel, and still less adherent on Inconel and on 4130 steel without the preplate. Cathode and anode reactions are suggested.

Jan 1, 1976

By E. G. Valdez

Laboratory research demonstrated that ceramic wall and floor tile can be produced from electric furnace phosphorus slags composed of calcium silicates. Grinding the slag in a pebble mill, followed by magnetic removal of deleterious magnetite, produced a raw material that could be compounded and formed into wall tile by dry pressing, sintering, and glazing. The effects of process variables such as forming pressure and sintering temperature were investigated. Wall tile bodies produced by this method were comparable to commercial tile. The tiles were readily glazed to a smooth shiny finish and met ASTM Specifications C34-62 for structural clay load-bearing tile. The estimated cost of producing wall tile by this method compared favorably with the retail market value for similar wall tile. Addition of borax or other additives to the ground slag followed by dry pressing and firing likewise produced a commercial grade of floor tile.

Jan 1, 1974

By E. D. Gardner

This paper discusses prospecting for lode gold and lists the principal lags and. regulations pertaining to locating; lode claims on public lands. It is a preprint of a part of a bulletin being prepared by the United States Bureau o Mines entitled "Equipping, Developing and Operating Small Gold Mines". The increased interest in gold mining manifested during the past few years (1932-1935) bas stimulated prospecting. Many adventurers have taken to the field to search for now gold deposits. A. large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the tope that it might assist these newcomers.

Jan 1, 1935

By W. A. Haley

The purpose of this investigation was to develop and improve mining methods for mining thin coal beds, to increase productivity, and to increase the recovery of coal. German coal planers and a modified longwall system of mining were introduced into American mines and are bringing about increased productivity and better recovery as compared with the conventional methods displaced. Since the first installation, 4 additional planers have been purchased by coal companies and over 1-1/2 mil¬lion tons of coal has been mined by them, using the modified longwall mining method. INTRODUCTION Except from 1932 to 1934, the growth of mechanical loading in underground bituminous-coal and lignite mines in the United States has increased steadily. The amount of coal loaded mechanically in underground mines has increased from 0.3 percent in 1923 to 79.6 percent of the total underground production in 1953.3/ The use of new and improved mining machines and auxiliary equipment, together with new techniques in mining methods, usually has resulted in increased productivity.

Jan 1, 1957

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

By Hylton R. Brown

Although extensive research has been carried on to determine the factors affecting the explosibility of carbonaceous dusts, as much has been published on coal-dust and grain-dust explosions recent reports of loss of life and property in explosions if metal dusts emphasize the lack of information on the extent of the dust-explosion hazard in plants manufacturing or handling; aluminum, magnesium, or zinc powder, as well as other metal or mineral dusts. Early investigators believed that only the carbonaceous dusts formed explosive mixtures with air, and it was not until near the beginning of the present century that the explosibility of certain metal and mineral dusts was recognized generally. In his book, entitled "Fire and Explosion Risks," published in 1904, Von Schwartz called attention to such hazards. Many vague references to metallic-dust explosions are found in the literature, such as "a severe explosion of aluminum dust occurred in the Middle West several years ago," but very little information seems to be available on the extent of the hazard, the number of explosions, or the amount of loss caused by explosions in pants handling metallic or mineral dusts or powders other than those of a carbonaceous nature. A search of the records of insurance companies, rating bureaus, fire underwriters,and fire-protection associations as well as the files and records of Government agencies has been made to obtain authentic data on explosion losses. To indicate the extent of the hazard a summary of laboratory tests covering the explosibility of certain metal dusts, with brief reference to their uses and Methods of manufacture, and the data compiled from the information available on losses are presented in this publication.

Jan 1, 1941

By Oliver Bowles

"The manufacture of asbestos paper began commercially about 40 years age but its principal development has taken place during the past twenty-five years. The asbestos used by the ancients, termed amiantus by Pliny was used for winding sheets, tablecloths and other fabrics. It was probably chrysotile fiber and was a woven and not a felted product, and there¬fore is not to be confused with asbestos paper. There are, however, some early references to paper manufacture that are of interest. Pontoppidian, Bishop of Bergen, in his Natural History of Norway, published in 1750, refers to paper made from asbestos found in the parish of Waldens. He states that this paper did not burn when thrown in the fire, but the writing on it totally disappeared. This indicates that the primary ob¬ject was to obtain an indestructible writing paper. About 100 years later, further efforts were made with the same object in view. In 1853, a patent was issued for a process of making paper from a mixture of asbestos and alum. Many experiments were made to manufacture suitable asbestos printing paper. Some such papers contained only about one-third asbestos, the remainder being of combustible material. Such papers would burn, but would leave a white residue which retained its shape and preserved the written characters. On account of the difficulty of obtaining a smooth and even surface, and the tendency for the material to absorb ink like blotting paper, asbestos paper is not well adapted for writing or printing purposes. Other early uses of asbestos paper were for ornamental wall-paper and carpet linings. None of the uses mentioned above have developed to anything of importance in a practical way, but the manufacture of asbestos paper has become a very important industry, and it has found extensive uses in ways that were never dreamed of by the early investigators.It is recorded that the first sheet of asbestos paper made in America was manufactured in 1876 by John Roberts & Son Company, in a mill near Waltham, Mass. The material first used was a long-fibered amphibole asbestos from Italy. About three years later, Canadian fiber was introduced and proved to be very satisfactory. The shorter grades of fiber which would otherwise be wasted were used for the manufacture of paper and board. For several years, the product of this mill was sold through Rice Kendall of Boston, Mass. From 1881 to 1900, the H. W. Johns Company, of New York, took the entire product which was 30C to 700 tons per year. The latter company built their own asbestos paper mill at Brooklyn in 1900. Keasbey & Mattison Company, of Ambler, Pennsylvania, began to manufacture in 1897. Other early manufacturers were: the Asbestos Paper Company, at Baldwinsville, Mass„ and Mr. B. S. Binney, at Shirley, Mass. The number of manufacturers gradually increased until at present asbestos paper is manufactured by the following ten companies:"

Nov 1, 1919

By E. A. Johnson

The Bureau of Mines determined the effect of slag additives on copper solubility and the distribution of typical impurity elements between copper-iron matte and silica-saturated fayalite (iron silicate) slag at 1,250° C, in CO-C02 atmospheres with 10 pct S02. Small additions (<10 pct) of CaO, A1203, and MgO were shown to decrease copper solubility in the slag. Additions of CaO increased the solubility of bismuth and tellurium in the slag at lower matte grades. Al 20 3 additions decreased the solubility of tellurium in the slag, but increased that of bismuth at lower matte grades. A1203 additions increased the solubility of both at lower matte grades. With no additives, matte grade did not affect the solubility of bismuth in slags, whereas increasing matte grade resulted in a slight decrease in the tellurium solubility in slag. Additions of CaO or As203 alone to the slag increased selenium and arsenic distribution to the matte, but had little or no effect on antimony distribution; whereas small MgO additions decreased antimony distribution to the matte but had no effect on arsenic and selenium distribution. In slags with no additives, selenium distribution to the matte increased with increasing matte grade, while that of antimony decreased and that of arsenic was unchanged.

Jan 1, 1982

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and, liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise eight be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and. removing the disintegrated clay particles from wells after the perforated pipes have been inserted. Mechanical methods for removing mud sheaths are quite satisfactory, but prompted by tie request of certain operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions.

Jan 1, 1934

By C. F. McCarroll

[Laboratory research and, control in the production an. utilization of petroleum and it 3 products have expanded greatly during the past decade, and much of the routine control and experimental equipment now rewires the constant daily use of liquid mercury. In spite of this ;;renter use, very little consideration has been given to the hazard that might be occasioned by the toxic vapors of mercury unavoidably spilled&apos; of otherwise exposed to the atmosphere during the normal procedure of laboratory open at ions. A simple visual examination ).&apos;.&apos; son-,, r° the laboratories reveal the presence of a considerable quantity of mercury in the cracks of floors, on work tables, and on ark, around equipment stands. Usually this mercury is contaminated with oil3/ and dirt so that it remaining in a finely divided state and a ;mall amount pre presents a relatively large surface for evaporation. Since :mercury shows measurable volatility at a temperature v,.^ lo.! 5o F., mercury vapor will be present in, the mercury _3 exposed promiscuously.]

Jan 1, 1939

By T. G. Mayhew, A. A. Bergeron, R. J. Mahany

This report describes an operational communications system which provides remote intra-terrestrial wireless transmission of environmental information. Design and modification specifications of requisite equipment are included along with a detailed description of system operation

Jan 9, 1976

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise might be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and removing the disintegrated clay particles from wells after the perforated Wipes have been inserted. Mechanical methods for removing mud sheaths are :quite satisfactory, but prompted by the request of certain .operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions. This report describes the laboratory work and deals generally with a chemical method for removing the mud sheath, cake, or plaster deposited against the face of oil sands in drilling wells end in wells that, on being shut in temporarily during periods of overproduction of oil, are conditioned for the shutdown .period by filling the well opposite the producing formations with mud fluid. The method described in this report was devised in the San Francisco laboratory of the Bureau of Mines and, as far as the writers have been able to determine, differs from any chemical method ever used in actual wells. The method proposes to add a small amount of calcium carbonate (preferably pulverized limestone) to the mud fluids before they are introduced into the wells so that the resultant mud sheaths will be susceptible to disintegration by acid solutions when it is desired to expose the faces of the oil sands in the wells.

Jan 1, 1934