Search Documents

Develop a safe, efficient filter for removing diesel particulate matter (soot) from the exhaust of underground mining machines equipped with water scrubbers. Approach The Bureau of Mines and the Donaldson Company, Inc., jointly developed a low-cost, disposable, pleated-media filter (PMF) system. The system is intended for use on Part 36 permissible equipment or other machines equipped with water scrubbers. The PMF is installed downstream of the water scrubber to take advantage of the cool exhaust produced by the water bath. This demonstration system was tested on three Jeffrey 4114 Ramcars and a Wagner LST-5 scoop at Utah Fuel Company's Skyline mine near Scofield, Utah. Figure 1 illustrates a clean filter element being inserted into the canister on the Ramcar. How It Works The PMF system consists of a water trap, an optional over-pressure relief valve, filter canister, and PMF Under normal operations exhaust from a vehicle equipped with a water scrubber is heavily laden with water, especially on immediate startup of the engine. The water trap is designed to remove most of the water droplets from the exhaust before they enter the PMF, thus improving PMF performance. The over-pressure valve is designed to limit the exhaust backpressure by venting off some exhaust gas before the: filter. It is attached to the water trap upstream of the PMF. Figure 2 illustrates and shows a break out sectional view of the location of the PMF on the Ramcar.

Jan 1, 1991

By Joseph Cervik, J. H. Perkins

The Bureau of Mines has conducted desorption work on fine coal particles at near atmospheric pressure. An apparatus has been developed that uses a capacitance manometer to measure desorption of methane from coal particles up to 2 inches in diameter and pressures up to 1,000 psi. This will make it possible to duplicate the desorption process as it occurs in its natural under- ground environment.

Aug 1, 1970

By R. R. Hornor

Due mainly to conditions brought about by the war , the metal mining industry in this country is now passing through one of the most critical stages in its history , and is confronted by new problems upon the solution and adjustment of which depends , in a large measure , its future welfare and prosperity . The chief factors contributing to the cost of production are the cost of labor and supplies . It is conceded by our leading mine operators , managers , and engineers that any material reduction in the cost of labor or supplies , within possibly the next two or three years , cannot be anticipated , anl it is not thought likely that pre - war prices will ever again prevail . This being true , the mine operator must look in some cther direction to effect economies that will lower production costs . If this cannot be accomplished it will mean , in many instances , that mines and metallurgical works will have to be closed and abandoned , which will tend to disorganize the entire industry . How to lower production costs and still maintain the present high standard of wage , is the problem that is engaging the serious attention of mine operators and managers over the entire country . In As a solution to this problem it is thought that the most promising field of investigation lies in the direction of systematizing and standardizing mining practice , so as to effect economies in the use of both labor and materials . other words , to eliminate , in so far as possible , unproductive effort and waste and thereby secure a maximum of productive results , It is not the idea to speed up work or to demand a greater effort on the part of the workman , but rather so to systematize and standardize the various under ground operations that his energy will be directed into more useful and productive channels ,

Dec 1, 1919

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown's run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the' main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972

Improve the safety of salt mine workers by providing a means for quickly identifying areas within the mine that?s how an increased potential for gas and salt outbursts. Approach Outbursts occur in salt mines when a high-pressure pocket of gas is intercepted during the mining process, resulting in a sudden and sometimes catastrophic expulsion of gas and salt. In one case, the amount of gas released through such an event caused an explosion that resulted in five fatalities. The U.S. Bureau of Mines has designed and developed a gas outburst prediction system that can quickly determine the potential instability of areas within rock salt mines. The determination is based on noise measurements obtained from samples of the salt as they are dissolved in water. This system improves upon technology currently available because it provides information in only a few minutes instead of in several days. In addition, present prediction systems are not only time consuming, but expensive because they require laboratory conditions and highly trained personnel to operate them and determine results.

Jan 1, 1989

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By Deno Pappas, Gregory Molinda, Eric Bauer, Christopher Mark, Daniel Babich

Groundfalls are much more likely to occur in coal mine intersections than in entries. NIOSH is using the experience of U.S. coal mines to determine the factors which influence intersection instability and provide guidelines for the safe excavation and support of intersections. Detailed field investigations have resulted in a database of U.S. coal mines containing 12 mines and 639 roof falls so far. By using the roof fall rate as the outcome variable, correlations between roof geology (CMRR), intersection span, and roof support have been established. Case studies have indicated that replacing 3- way intersections with 4-way intersections may not reduce the total number of roof falls. Additionally, the size of intersection spans tend to decrease with lower (weaker) CMRR. Protocols have been established for the collections of roof bolt parameters. The performance of individual roof bolts can now be tracked with roof fall rate.

By Harry W. Campbell

A mineral survey conducted by the U.S. Bureau of Mines in 1984 identified no mineral resources or prospects with mineral development potential in the Pit River Canyon Wilderness Study Area (WSA). Basalt suitable for aggregate and fill is in the WSA but rock of this nature is abundant in the region and closer to potential markets.

Jan 1, 1984

By Oliver Bowles

"Introduction.During recent months the Bureau of Mines has conducted a detailed study of the slate industry with special reference to increased efficiency in its production, preparation and utilization. The results of these investigations will be incorporated in a forthcoming bulletin. The purpose of this preliminary paper is three-fold. One object is to bring to the attention of slate producers certain modifications in manufacture and classification which would encourage a wider use of slate. A second purpose is to direct the thought of roofers toward the importance of proper laying of slate, and the third object is to acquaint the general public with its enduring qualities.Origin and character.Without entering into any detailed discussion of the origin and history of slate, a subject to be covered in the bulletin mentioned, it may be of interest to the general reader to know that slate is originally formed from mud or soft clay, carried down by streams and laid down in successive layers in deep water. The pressure of superimposed materials gradually compresses the clay into a firm rock known as shale. In many places this shale was, during the succeeding ages, subjected to intense pressure and folding due to mountain-building forces within the earth. This intense pressure, together with high temperature, changed the clay into other minerals such as mica, chlorite, and silica, which are very resistant to weathering, and also developed a very definite cleavage or splitting direction which characterizes the rock as slate. It is this property which renders slate of value for roofing, for, by using a broad chisel and a wooden mallet, a slate worker can readily split it into thin sheets which are later trimmed into rectangles of various sizes."

Jul 1, 1921

By J. J. Rutledge, C. A. Herbert

In 1916 the Bureau of Mines, the Illinois Geological Survey, and the University of Illinois, working under a cooperative agreement, began an investigation of the subsidence of the surface above coal- mining operations. Four widely separated places where mining was in progress were selected as observation stations-one in the northern Illinois longwall coal field, one in the central Illinois coal field where the room-and- pillar panel system of mining was being used, and two in the thick coal of southern Illinois where the room-and-pillar panel system of mining was employed. These four points of mining activity gave a rather wide opportunity for observing subsidence when different mining methods were used. The four places selected for investigation of surface subsidence due to coal mining have been designated as follows: 1. A, in the northern Illinois longwall coal field, where the coal company has been operating coal mines for 30 years and where long- wall advancing is the only method of mining. 2. B, in Perry County, where panel room-and-pillar mining of a thick seam of coal is in progress and where mining operations have been carried on about 40 years. 3. C, in Macoupin County, where the coal company has been min- ing coal by the panel room-and-pillar method for about 15 years. 4. D, in Franklin County, where the coal company has been mining coal for 10 years by the panel room-and-pillar method.

Jan 1, 1927

By Robert H. Essenhigh

A stirred reactor (SR) combustion system has been developed to gather information on the mechanisms of ignition and flame propagation of coal dust under conditions similar to those found in coal dust explosion flames. The prime scaling variable considered in this study is that of rapid particle heating (between 105 and 106°K/sec) which is accomplished by means of turbulent mixing during combustion. The SR combustors tested in this study have consisted basically of spheres hollowed in the centers of refractory housings. Coal and air mixtures have been injected into the spherical combustion chambers through a single jet, two opposed jets or four opposed jets. The diameters of the jets have ranged from 0.63 to 0.22 cm. The volumes of the combustion chambers have ranged from 1.0 to 0.2 liters. The reactors have been equipped with thermocouples embedded in the combustion chamber wall as well as a thermocouple located in the exhaust gas stream. In the latter versions of the SR, provisions were made for both solid sampling and gas sampling of the reactant stream exiting from the combustion chamber. Experiments have been carried out using pulverized bituminous coal. The coal has been reacted in an SR in mixtures of air and air/nitrogen. These experiments have provided information on the mode of ignition of the coal as well as yielding information on the kinetics of coal pyrolysis through the use of SR theory. Ash tests performed on the reacted samples collected from the SR indicated that the majority of the values of weight loss percentage were between 60 and 70 percent. The percentages of weight loss were relatively unaffected by changes in temperature which varied between 1100 and 1700°K and by changes in residence time which varied between 10 and 20 millisec. Volatile matter tests performed on the samples indicated that the volatile matter left in the char ranged from 3 to 20 percent of the original content. By assuming that all the mass loss was due solely to pyrolysis with no combustion occurring at the particle surface, Q-factors for each test have been calculated. The results of these calculations indicate an average value of Q equal to 1.88. This finding shows that the majority of mass loss can be attributed to pyrolysis. The fact that the extent of reaction varies only slightly over the range of test conditions has been examined in the context of the two component hypothesis of coal constitution. This approach leads to the conclusion that the reaction of the "easily evolved" component VMI is extremely rapid and that the majority of it is removed from the coal in times less than the residence time in the system. This means that the volatile residue remaining in the char can be considered to consist of component II, VMII. If the mass fraction of VMI = 0, then an activation energy of 18.0 kcal is obtained for the pyrolysis reaction. If the mass fraction is assumed to be 0.75, the activation energy increases to 31.2 kcal.

Jan 1, 1978

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

By J. J. Bourquin

"The Keely mine at Dagger, Indiana, is one of the few mines that is being operated successfully on a cooperative basis. This shaft mine is developing 133 acres of coal in the Indiana No. 6 bed, which here averages 5-1/2 feet thick and. lies about 110 feet below the surface. Thirty seven (37) miners and twenty (20) company men or day man are employed, and the daily output is around 300 tons. Practically the entire production is sold by contract for railroad use. No mining machines are used and all coal is produced by pick work.The mine was originally owned and operated by the Stockton Coal. Co. of Dugger, but about eight years ago it was leased to Mr. Roy Price. He sub-leased the property to ten miners, who formed an association known as the Dugger Mutual Coal and Mining Co., to work the mine cooperatively.At first many difficulties were encountered; the cooperative idea is an old one, but the practice was new to those interested. Some of the men were energetic, ambitious workers; others were inclined to let their associates produce the coal but wanted to share in the profits. In time, after a hard struggle and many changes in the personnel of the company, business-like methods were adopted and the mine was put on a paying basis."

Feb 1, 1983

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

By Joseph S. Coffman

The Bureau of Mines investigated the availability of barite (BaSO4) from 35 U.S. and 41 non-U.S. mines and deposits in 17 market economy countries (MEC's). This evaluation assesses the availability of mud-grade barite, and concentrates consumed by the chemicals and fillers industries. The demonstrated resources defined in this analysis totaled 130 million metric tons (Mmt) of barite (contained BaSO4), yielding a potential 115 Mmt of recoverable barite concentrates. At the 1984 MEC production rate, the evaluated resources would last about 30 yr; however, this would include production costs of up to $100/mt concentrate. An average price needed to cover all costs of production over the life of each operation was determined for both mud-grade and chemical- and filler-grade barite products. Including a 0-pct discounted-cash-flow rate of return (DCFROR), regional weighted- average total production cost ranged from $38/mt for barite concentrates in Asia to $71/mt for U.S. operations. Transportation costs have the greatest impact, contributing up to 60 pct of the total cost of production. Rail transportation costs from the mines to U.S. markets are generally significantly higher than ocean shipping rates on imports.

Jan 1, 1986

By J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) slip along steeply dipping faults and (2) fracturing of strong strata above, or below, the coal seam. Both failure modes produce dynamic or ?shock? loads on the perimeter (roof, rib, floor) of mine openings. Special consideration should be given to these failure modes in planning of deep coal mines since their occurrence is not within the professional experience of many contemporary workers, and their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

In 2001, a total of 2,144 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 14.7% of all mining operations. • Bituminous mines comprised 92.0% (n=1,972) and anthracite mines 8.0% (n=172) of coal mining operations. • More than 71% of coal mines were located in three states: Kentucky (29.5%), West Virginia (21.3%), and Pennsylvania (20.6%).

Apr 1, 2003

By C. Lorimar Colburn

"The use of helmets during the war has accentuated interest in the advisability of using stiff hats in mines to protect the miners against falling rocks. About forty per cent of the accidents in mines are due to falling rocks or roof. A large number of these accidents could be prevented if the miners wore stiff hats or helmets.The use of head protective devices in minas is not new, for they have been in use for many years in Europe and in the Lake Superior District in the United States. In practically all of the mining districts in Europe stiff hats of some kind are required by the mine management. George S. Rice, chief mining engineer of the Bureau of Mines, reported that in Germany, Belgium, and France stiff hats made of papier mache or felt rosin are in use. Similar hats are generally employed in the Lake Superior District. In building the subways of New York and Philadelphia it was the practice of engineers and workers to let the hair grow very long and to wear a close fitting cap or felt hat. In Germany the hats are high like the military helmets, whereas in France and Belgium they fit more closely to the crown. In England the practice is mixed. As a rule the miners use soft padded caps, but in Yorkshire many of the miners use sole leather, tight-fitting caps of jockey pattern with the seam forting a little ridge down the middle of the cap. These hats are very useful allow thin beds of coal, as in crawling one is very likely to strike his head a sharp piece of rock or on a timber. Of course, such mishaps are more likely to occur to a man not familiar with the mine. It must be admitted such hats do not stick on well, though this is usually due to their not being especially fitted. The German hat is particularly unsuited to an American-shaped head.It is interesting to note that on the continent tight cotton caps are generally worn over the hair and under the hard hat. This is a measure for cleanliness which is excellent. In low beds of coal share much crawling on hands and knees is necessary the dirt and coal dust sift down, making the miner black and dirty. In metal mines stiff hats are of especial use in shaft work; also in raises or high stapes. A small fragment of rock falling some distance either down a shaft or raise would kill a man if it struck him squarely on the head. A stiff hat or helmet may protect him and save his life. At a station in a shaft where men are loading the cage or skip, some kind of adequate head protector should be compulsory. A head-protecting hat or cup which is also a good insulator should be worn where there is danger of striking one's head against a wire carving an electric current."

Jun 1, 1920

By L. W. Higley

Procedures were developed for reclaiming high-temperature alloy scrap in the form of standard cobalt-base alloy. A cobalt-base, multicomponent, high- temperature alloy, such as S-816, can be successfully melted from scrap, and its specified chemical composition can be retained. Induction furnace melting in a controlled atmosphere was used to obtain ingots that were subsequently fabricated by impact forging to provide specimens for heat treatment and testing. Of the numerous metal elements in S-816 alloy, only small quantities of molybdenum were lost in the melting operation as finally developed. Test results indicated that the scrap material, after melting, forging, and heat treatment, was equivalent in room-temperature tensile strength, in high-temperature creep and stress-rupture properties, and in chemical composition to commercially produced S-816 alloy made from virgin material.

Jan 1, 1963

By Oliver C. Ralston

OUTSTANDING TRENDS of the year included the following: 1. Concentration and beneficiation of iron ores to provide improved blast-furnace feed and extend ore reserves. 2. Successful development of pelletizing and sintering procedures for fine iron ores. 3. The realization that cyclone separation could replace existing classifiers in many grinding circuits. 4. The rapidly blossoming metallurgy of ultrapure silicon and improvements in zone melting. 5. The rapid increase in the use of liquid-liquid extraction and ion exchange in hydrometallurgy. 6. The industrial application of vacuum melting on the 100-ton scale. 7. The hope for developing a columbium (noibium) base alloy for high-temperature use. The technologic advancement in metallurgy that had the greatest effect on the American economy was the beneficiation of iron ores to give improved feed for blast furnaces and indirectly extend our ore reserves. This was not a sudden development but rather culmination of a decade of intensive effort.

Jan 1, 1958