Search Documents

By Jr. Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

By M. B. Cooke, A. D. Bauer, E. W. Dean

The Bureau of Mines is collecting and analyzing representative samples of crude petroleum from all the producing fields in the United States , and the results are being published in a series of reports that are preliminary to the issue of a bulletin covering the entire survey . The bureau has recently completed a survey of crude oils from the Kansas district . In all 27 samples were collected and analyzed , under the direction of A. W. Ambrose , chief petroleum technologist of the Bureau. Valuable assistance was received through the cooperation of oil companies operating in the State , especially the Prairie Pipe Line Co. , and the Empire Pipe Line Co. The present report issued as Serial 2322 , on the Kansas crudes , forms the fifth of the series . Of the four previous papers , the first ( No. 2202 ) deals with crudes from the Eastern fields of the United States , the second ( No. 2235 ) with crudes from the Rocky Mountain district , the third ( No. 2290) gives additional data , cn viscosities and pour tests , for the crudes from these two fields , and the fourth ( No. 2293 ) covers the fields of northern Texas , northern Louisiana , and Arkansas . The details of the methods of collecting samples , making laboratory tests and interpreting results , have been discussed in these earlier reports . It has also been pointed out that the only adequate method of interpreting analyses of crude oils is to compare the individual reports with the analysis of some crude oil that is familiar to the operator . For this reason , no comprehensive discussion of the results of the Kansas survey is attempted, although some general statements may be made .

Feb 1, 1922

By Andrew B. Cecala, Edward D. Thimons

"The Bureau of Mines has recorded a number of different background dust sources that significantly contaminated the air breathed by bag machine operators. These background sources, observed at five different plants over the past 2 years, can expose bag machine operators to more significant dust concentrations than the filling process itself. To keep bag operator exposure within acceptable dust levels established by the Mine Safety and Health Administration, U.S. Department of Labor, the significance of these background sources must be realized, and the sources must be identified and controlled. The purpose of this work is to identify common background dust sources and show the significant effects that they have on the bag operator's overall dust exposure. INTRODUCTIONThe purpose of this report is to identify some common background dust sources in and around the bag-filling area. Although these background dust sources are of ten unrecognized, they can be more significant sources of contamination than the dust generated from the bagging process.The bagging of mineral products into 50- and 100-lb paper bags is common throughout the entire mineral processing industry. Bagging is performed by a bag operator who sits in front of a two- or four-station fill machine. The bagger's function is to attach empty bags to the fill nozzles as filled bags are ejected from the machine. If the product being bagged is extremely fine (smaller than 200 mesh), the bag operator's dust exposure is usually one of the highest in the plant.The bag operator is exposed to two primary dust sources. The first is product blowback during the bag-filling cycle. This occurs as excess pressure is released from around the fill nozzle during filling. As the excess air forces its way out of the bag, product is forced out with it. This blowback of product leaving the bag creates a considerable amount of dust. The second major source is the ""rooster tail"" of product thrown from the bag valve and fill nozzle as the bag is ejected from the fill machine. Since the bag is pressurized as it leaves the machine, product spews out of the valve for a few seconds."

Jan 1, 1986

By H. J. Heinen

This report summarizes preliminary research studies by the Bureau of Mines in electrowinning molybdenum directly from pure or impure molybdenum trioxide (MoO3) by fused-bath electrolysis in an open graphite cell without need of a protective inert atmosphere. A formulated electrolyte of the tertiary system containing 41.6 percent sodium pyrophosphate, 16.7 percent sodium tetraborat, 33.3 percent sodium chloride, and 8,4 percent molybdenum trioxide, by weight, electrolyzed at 1,000° C,, gave excellent results. Current density studies were made over a range from 20 to 260 amperes per square decimeter. Current efficiencies of 80 to 90 percent were obtained over the entire range. Yields up to 500 grams of molybdenum per kilowatt-hour were obtained. Higher current densities, however, reduced yields and produced a finer grained metal. The two most important facets in electrowinning molybdenum from MoO3, in an open cell, are temperature and electrode spacing to minimize or eliminate the formation of the suboxide MoO2, the major source of oxygen contamination. At temperatures of 1,000° C. and higher, together with the proper spacing of the electrodes, formation of oxides are practically eliminated. Molybdenum metal electrowon from pure MoO3 was 99.9 percent pure and contained 0,056 percent oxygen and 0,007 percent carbon. This metal, when arc-melted, had a Vickers hardness number of 175 and contained 50 parts per million oxygen and less than 10 parts per million carbon. Molybdenum metal electrowon directly from an impure MoO3 containing 90 percent MoO3 resulted in a metal of 99.8 percent purity.

Jan 1, 1961

By Horace M. Lawrence, Edmund S. Leaver

"The sulphidizing filming of minerals in oxide ores as a preliminary treatment to aid their recovery by flotation is known practice. In this work the use of barium polysulphide does not appear to have been considered. A study of the properties of barium lead to the following comparative investigation of the sulphides and polysulphides of the alkaline and alkaline-earth metals. It is thought that barium polysulphide may prove to be a more satisfactory sulphidizing reagent than others now in use under conditions that favor the cheaper barium reagent.For the investigation two fairly typical oxidized ores of copper and lead were selected. The copper ore came from the Big Indian Mine in southeastern Utah, and assayed 3.8% Cu; the copper was present in a sandstone gangue mainly as the carbonates, malachite and azurite, with less than 0.2% as sulphides, or silicate. The lead ore is from the Tintic Standard mine in the Tintic district, Utah. It is typical of the oxidized lead-silver ores of that district; the lead is present in an oxidised form in a siliceous gangue, much: Uncolored by ferric oxide. The sample assayed 5.15% Pb and 11.3 oz. Ag.In addition to the results obtained in this investigation, there are included some results secured by Mr. J. B. Lain, consulting metallurgist of Reno, Nevada, on a sample of ore from the Chino Copper Co. The ore assayed about 1.7% Cu, of which about 0.25% was nonsuiphide."

Aug 1, 1925

SCOPE AND APPLICATION The rules cover the installation and use of electrical equipment in coal mines.- For generating stations, substations, lines, and equip¬ment aboveground, reference is made to existing rules covering such locations, viz, the National Electrical Code and the National Electrical Safety Code and any existing State or municipal regulations. The purpose of the rules is to set forth methods for safe electrical installation. In preparing the rules five basic measures for safe¬guarding the use of electricity in mines have been followed, viz 1. Remove the contributory causes of accidents or danger. 2. Remove from the vicinity of electrical apparatus all elements susceptible to the influence of electricity. 3. Keep the electric current where it belongs, if possible; if not, limit the area of its activity by protective devices. 4. Use a. large factor of safety in the selection, installation, and in¬ spection of equipment. 5. Have full control of the operation of electrically driven machines. Each rule that is given is proposed as necessary or helpful to the accomplishment of one or more of these measures. DEFINITIONS OF TERMS USED Alive.-See definition of " live." Approved.-The term " approved " means accepted as suitable by a competent committee, board, or organization designated by those adopting the rules. Authorized person.-The term " authorized person " means a per¬son appointed or permitted by the official designated by the State mining laws as the one in charge of the operation of the mine to carry out certain duties incident to the generation, transformation, and distribution or use of electric energy in the mine, such person be-

Jan 1, 1926

By C. M. Bouton

Although much valuable work has been done in the study of dust explosions, the laboratory technique has not been developed to the point where the many factors involved can be properly controlled, and thus where really fundamental information can be obtained. This paper presents a brief discussion of the difficulties encountered in fundamental work on dust explosions, a description of apparatus intended, to overcome some of them, and an account of some results obtained. FACTORS INVOLVED IN DUST EXPLOSIONS The more important factors pertaining to the dust cloud itself which are known to determine the phenomena of explosions are (1) the kind of dust; (2) its fineness; (3) its concentration in the exploding cloud; and (4) the nature of the interior motions, or turbulence, of the cloud before and during the explosion. These factors are arranged in what seems to be an ascending order of complexity. The kind of dust is the factor most easily subject to control. The fineness of the dust at first sight seems to be a controllable factor, but when it is recalled [that] most explosible dusts are mixtures of particles of continuously varying sizes so small as to pass through the finest woven sieves, and therefore difficult to separate either for purposes of analysis or experiment, the fineness is seen to be a factor difficult to control accurately.

Jan 1, 1929

By P. Kovalchik, S. Peng, G. Cole, R. Matetic

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90 percent of coal miners and 49 percent of metal/nonmetal miners had a hearing impairment by age 50 (Franks, 1997). Mine workers are exposed to additional noise levels underground due to the reflection of machine-generated noise that would otherwise dissipate in an aboveground setting. Determining the sound-absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed rather than being reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes a finite room, a diffuse field and a relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper presents a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients are essential for determining and predicting potential overexposure to machine operators in different mine environments.1

By A. B. Hooker

All state mining laws require that flame safety lamps be used in gassy mines; the laws of some States require that safety lamps be kept for emergencies at every coal mine, whether gassy or nongassy. The use of the flame safety lamp has been widespread because it is the only defice readily available for detecting both the presence of methane and deficiency of oxygen. This paper reports the results of an investigation by the Electrical Section, in cooperation with the Gas Section, of the Pittsburgh Experiment station relative to the behavior of permissible flame Safety lamps in mine atmospheres deficient in oxygen and the effects of methan5/ on the detection of oxygen deficiency.

Jan 1, 1937

By A. B. Hooker

All State mining laws require that flame safety lamps be used in gassy mines; the laws of some States require that safety lamps be kept for emergencies at every coal mine, whether gassy or nongassy. The use of the flame safety lamp has been widespread because it is the only defice readily available for detecting both the presence of methane and deficiency of oxygen. This paper reports the results of an investigation by the Electrical Section, in cooperation with the Gas Section, of the Pittsburgh Experiment Sta¬tion relative to the behavior of permissible flame safety lamps in mine atmospheres deficient in oxygen and the effects of methane5 on the detection of Oxygen deficiency.

Jan 1, 1937

By F. N. Kissell, C. D. Litton

This study ranks the factors impacting survival during a coal mine fire. It bas already been established that reducing time delays is the most important factor in saving lives. Consequently every event during afire is measured in terms d its duration, and the effectiveness d any action taken to improve survival is measured in terms d the time it saves. By ranking actions according to time saved these authors found that a comhination d actions was most effective. This combination was: • installing lifelines. • moderately decreasing air leakage and • decreasing the fire growth rate. Changing ventilation leakage alone was much less effective, as was altering the CO (carbon monoxide), sensor alarm threshold. These results confirm an earlier fault-tree study on escape from mine fires. The fault-tree study bad shown that, with the exception d delays, single factor changes have minimal impact. Significant reductions in fire fatalities only take place with multiple factor changes.

By Lloyd A. Morley, Alan M. Christman

Presented below is a review of how the objectives, as outlined in the statement of the problem, were achieved. 1. Methods of evaluating the performance of grounding systems must be described. These methods are the subject of Chapter III. 2. Field trips to operating mines should be undertaken, and a cri¬tique of their grounding systems made upon the basis of obser¬vation and the application of the above techniques. An analysis of field trip data, along with practical recommendations, is in¬cluded in Chapter IV, while a complete review of all field trips is given in Appendix I. 3. Because of their thoroughness, present coal mine regulations should be evaluated, and their applicability to open-pit environ¬ments appraised. This has been done in consultation with governmental agency, manufacturing, operating mine, and consult¬ing engineers. As stated in Chapter IV, insight gained through field observations has served to amplify and extend the base of knowledge from which the recommendations were made. 4. The results of these investigations should lead to suggested Federal standards. Such recommendations comprise Appendix II. In addition, several important factors, which are discussed in Chapter IV, were brought to light as a direct result of the field research. 5. Seasonal variations in the earth resistance of ground mats, as illustrated by Table 12, reinforce the need for periodic

Jan 1, 1976

By B. R. Mohal, F. F. Aplan, S. Chander

"Dust abatement by water sprays involves the subprocesses of 1) collision between dust particles and water droplets, 2) adhesion of particles to droplets, and 3) engulfment of particles by the droplets. A review of the fundamental aspects of these subprocesses shows that collisions between particles and droplets are determined by aerodynamics and the size and surface charge of the particles and of the droplets. However, the adhesion and engulfment subprocesses depend upon the wetting characteristics of the particles. Although wetting agents (also known as surfactants) have been used as dust suppressants in several investigations, conflicting results are available regarding their effectiveness. In this paper, we show that these results can be explained if the effects of coal rank on surfactant adsorption and wetting characteristics are taken into account.The influence of several nonionic surfactants containing polyethoxy adducts on the wetting behavior of coal is presented. The wetting was determined by a modified Walker Test method, and contact angle measurements. The results show that the wettability of coal depends upon coal rank, structure of the hydrocarbon chain of the surfactant, and the number of ethoxy groups in the molecule.IntroductionDue to the inherent nature of the mining process, a large number of particles are generated, a portion of which becomes airborne to create dust. Dust can be aesthetically and environmentally unacceptable and it can also be explosive. Fine particles in the respirable size range ( < 5 urn) are con-sidered to cause lung diseases, namely, silicosis, pneumoconiosis, etc.(1) Several approaches to reduce dust in mine environments are practiced throughout the mining industry. These include decrease in generation of dust through improvements in mine machinery, ventilation (in which lower dust levels are achieved by dilution of contaminated air with clean air), and dust removal methods. Water sprays are most commonly used to remove dust par-ticles. Recently, scrubbers are reported to have been installed on mining machines to remove dust,(2,3) which also make use of water sprays to reduce dust."

Mar 1, 1989

By A. B. Hooker, Iilsley. L. C.

"Flame safety lamps have been used for about one hundred years in coal mines where a dangerous accumulation of explosive mine gas (methane) might occur and thus render the use of ordinary unprotected flame lamps dangerous. Flame safety lamps are not only used for illumination, but also for detecting the presence of dangerous percentages of methane mixed in the air of the mine.The safety of the lamp depends chiefly upon the cooling qualities ofThe safety of the lamp depends chiefly upon the cooling qualities of the wire gauze used to permit free circulation of the air through the lamp. If one enters a part of the mine where methane is present in the air, the methane enters the lamp and coming in contact with the wick flame is ignited and continues to burn within the gauze without igniting the methane surrounding the lamp. If the air within the mine is traveling at a velocity of several hundred feet per minute the burning gases may be driven through the gauze by the air current. If the gauzes are properly designed and of the proper material, these burning gases will be so cooled as they pass through the gauze that they will not cause an ignition of the gas surrounding the lamp. In order to test the effectiveness of a given safety lamp, tests are made in moving explosive mixtures of gas and air arranged to simulate mine conditions.The Bureau of Mines investigated many features relative to the safety of flame lamps and in 1915 established an official schedule known as Schedule 7 whereby flame lamps having certain prescribed qualifications would be approved as permissible for use in gaseous mines."

May 1, 1920

By Raymond B. Ladoo

Deposits of talc are known in many districts in Canada but at the present time active mining operations are reported only in Ontario . Here three companies are now operating, two of which, George H. Gillespie & Co. , Ltd. , and the Anglo- American Talc Co. , are at Madoc . The operations of the former company are probably the largest and best known in Canada . The writer , in his capacity as an engineer of the U. S. Bureau of Mines , was permitted by this company to make an inspection of its mine and mill in June, 1920 , and study the methods employed . This information was desired for comparison with methods employed in the United States . The following description is based on observation made during this visit , supplemented by data supplied by the company .

Sep 1, 1920

By Victor E. Kral

"INTRODUCTION The Segerstorm-Heizer property was examined by engineers 3/ of the Bureau of Mines in May and June 1942 and Mach 1943. As a result of these examination, the Nevada State Department of Highways,constructed 9.3 miles of graveled road under the mine access-road program. A magnetometer survey was made by the Geophysical Division 4/ in October 1943, and as a result the Mining Branch set up and conducted a core-drilling,project. Work on the deposit started May 24, 1944, and was suspended on July 31, 1944, but was resumed on December 4, 1944 and continued until completion on March 27, 1945.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as it, primary objective the more effective resource to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Kinickerbocker, chief analyses samples and performs beneficiation tests."

Mar 1, 1947

By Alla D. Mah

No experimental heat-of-formation value has been reported in the literature for cerium sesquioxide. The heat of formation of bismuth sesquioxide has not been determined in recent years, and the older value was subject to large uncertainty. Accordingly, the heats of combustion of cerium sesquioxide and bismuth metal were measured by the Federal Bureau of Mines. The heats of formation were: ?H°298.15 = -427.01 ± 0.70 kcal. /mole for cerium sesquioxide and ?H°298.15 = -137.16 ± 0.30 kcal./mole for bismuth sesquioxide. The free energy of formation was estimated for cerium sesquioxide and accurately calculated for bismuth sesquioxide. The data were compared with values in the literature.

Jan 1, 1961

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (-300° C) and later (>400° C) combustion stages of mine conveyor belts could be predicted by a smoke particle characteristic. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 150°, 250°, and 1,000° C, with a furnace airflow of 10 L/min. The variables studied, as a function of time, included hydrogen chloride and carbon monoxide concentrations, the average smoke particle diameter (d8 and number concentration (no), and the product of the average smoke particle diameter and concentration (dgn0) Other variables included the sample and furnace temperatures and the sample mass weight loss. Results show that the inverse of the smoke particle diameter-concentration product (ldgn0), correlates directly with the hydrogen chloride and carbon monoxide toxicities released in large quantities during the early and later stages of combustion.

Jan 1, 1989

By Raymond W. Hiteshue, Henry H. Ginsberg, Paul S. Lewis

Coal was gasified in the presence of up to 3.57 million roentgens of gamma rays by the Bureau of Mines to determine whether the irradiation increased the gasification rate or yields of methane and hydrogen . High volatile A bituminous coal was gasified with steam at 500 and 1,500 psig and temperatures of 1,400 ° and 1,800 ° F ; five other coals ranging in rank from lignite to anthracite were gasified at 500 psig and 1,800 ° F. The average results of replicate experiments with and without radiation were compared for possible effects of radiation from 40,000 curies of radioactive cobalt . The irradiation had no gross effect on the gasification rate or on the yield and distribution of methane and hydrogen . It was concluded that gammaray irradiation produced no improvement in the technology or economics of coal gasification .

Jan 1, 1964

By B. W. Madsen

Bureau of Mines research to recover arsenic from mining industry waste material and process streams is reported. Batch and column approaches were investigated for adsorbing arsenic from acid leach solutions and ion-exchange eluate solutions with hydrated titanium dioxide granules. A method for producing hydrated titanium dioxide granules was devised to provide material suitable for use in a packed adsorption tower. Selective adsorption of arsenic from acidic leach solutions was achieved. The loading capacity of arsenic on the granules was 14 wt-pct when synthetic solutions were used, but lower when actual leach solutions were used. Other elements in the leach solution were Zn, Cd, and In. The granules were used in an attempt to lower the arsenic content in a solution containing 0.95 g/l W and 0.027 g/l As from a process devised by the Bureau of Mines to treat Searles Lake brine. The arsenic content was lowered to less than 0.001 g/l, but unacceptable amounts of tungsten also were adsorbed by the granules. Adsorbed tungsten was partially stripped with pH 11.5 NaOH, and both tungsten and arsenic were completely stripped with 5M NaOH solution. Repeated loading and stripping of the granules had no effect on the loading capacity for arsenic.

Jan 1, 1983