Search Documents

By A. B. Hooker, R. A. Kearns

Material used for flame safety lamp gauzes should possess the following qualities: (1) mechanical strength, (2) resistance to corrosion under service con- ditions, (3) a relatively high thermal conductivity, (4) a melting point above the ignition temperature of mine gas. Heretofore, three metals have been used for flame lamp gauzes, namely: steel, brass and copper. While each of these has the requisite qualities to some extent, none of them is an ideal gauze material. Copper gauzes lack mechanical strength, especiall, after they have been heated; brass and copper both have comparatively low melting points so that before the gas ignition is reached the gauze metal is attacked and oxidized under the action of the heat. Steel corrodes readily in damp atmos- pheres and if the lamp stands unused under these conditions for some time, the gauzes become unfit for service. Tests of these three materials have shown that steel offers the highest degree of safety. Manel metal, the natural alloy of nickel and copper, is practically noncor- rodible. Its relting point is approximately the same as that of steel. From time to time it has been suggested that this alloy might be a better gauze material than steel, since gauzes made of Monel metal should have all of the good qualities that steel gauzes possess and, in addition, would not corrode appreciably in ordinary mine atmospheres. One advocate of this use for Monel metal, the International Nickel Co., through their development engineer, Mr. Robert J. McKay, cooperated with the Interior Department, Bureau of ines, to the extent of supplying twelve sets of 30 mesh, Monel-metal gauzes for tests. Those gauzes were made up by the same lamp manufactur- er ho rade the steel gauzes used in the previous investigation. Being made by the same processes as the steel gauzes, these Manel-metal gauzes were needlessly given the same anti-rust coating that is always applied to steel gauzes to prevent any corrosion before the gauzes are used. In previous tests the Bureau of Mines had collected data as to the behavior of steel gauzes. In determining the value of Monel metal as a gauze material, it was planned to obtain similar data with Monel-metal gauzes, and thus make a direct comparison with the steel gauzes. In addition, steel and Monel-metal gauzes

Apr 1, 1923

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

Provide reasonably priced, reliable fire protection for blasthole drills. Approach An automatic fire sensing and suppression system using both dry and gaseous chemicals was developed, and is more shock and vibration resistant than similar industrial fire protection systems. How It Works Temperature sensors mounted in the drill's machinery house, hydraulic room, operator cab, and transformer area detect the heat from a fire, and trigger a sequence of actions. The same fire fighting sequence can be initiated from manual alarm boxes in the cab, hydraulic room, or machinery house. Electrical power to the drill Is immediately cut off, and a horn sounds to warn the drilling crew. After a 40-second, built-in, delay to allow time for drill's ventilating fan to stop, gaseous and dry chemical fire extinguishing agents are piped to and released in various rooms of the drill. The gaseous extinguishing agent (Halon 1301) is released in the machinery house, hydraulic room, and operator cab where dry chemical clean-up from electrical panels and machinery would be difficult and costly. Dry chemical is piped to the transformer room at the rear of the machine. Location of the principal components of the system are shown in the drawing.

Jan 1, 1979

By Linda L. Chasko, Charles P. Lazzara, Ronald S. (deceased) Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

Jan 12, 2005

By M. G. Cherniack, A. J. Brammer, D. R. Peterson

Over the past two decades, there have been significant reductions in industrial exposures to hand-arm vibration, especially when specific tools and work processes have been redesigned to incorporate anti-vibration and ergonomic principles. Nevertheless, Hand-Arm Vibration Syndrome (HAVS) remains a significant occupational health problem as disease symptoms continue to occur even when vibration exposure levels believed to incur low risks have been reached2. This inconsistency may be related to the methodology that is typically used to estimate workday vibration exposure levels, involving laboratory and/or very short duration field measurements coupled with estimates of overall eight-hour tool operation times determined from brief observations of tool tasks and/or self-reported surveys. One solution is to use small, commercially-available, personal vibration dosimeters to calculate, record, and display long-duration vector sums and energy equivalents of vibration. However, since these devices are attached to the worker and require tool-mounted accelerometers, they are incompatible with the worker performing normal duties involving putting down or changing tools. In addition, these commercial systems do not allow for the characterization of the transmission of vibration to the hand such as monitoring the mechanical coupling between the hand and the tool handle (e.g., grip forces). O’Boyle and Griffin showed that variations in applied force can alter vibration transmission characteristics by 50% or more indicating that the measurement of grip force is essential for modeling vibration transmissibility and vibration exposures5. In summary, a need exists for the development of a method and device that will more accurately characterize workday-long vibration exposures. Methods A portable, light-weight, Vibration Exposure Monitor (VEM) system was developed to record user-specific tool-operating times, vibrations, and grip forces throughout all, or a representative part, of a workday. It monitors frequency weighted and unweighted accelerations from a palm-mounted uni-axial accelerometer (Model 352C22, PCB Piezotronics, Depew, NY) and calculates exposure levels using the root-mean-square (RMS) and higher power mean values, such as the root-mean-quad (RMQ) and the root-mean-oct (RMO). Grip forces are also monitored using a palm-mounted force sensor (Model 400, Interlink Electronics, Camarillo, CA) from which average grip force levels and exerted grip extrema are calculated. At the core of the VEM system is a commercially available, battery-powered microcomputer (Tattletale, Model 8v2, Onset Computer, Onset, MA) with one megabyte of memory and eight analog channels using 12-bit sampling at a single-channel maximum of 100 kHz. Analog signal processing (i.e., anti-aliasing, with cutoffs at 4 and 1250 Hz, and ISO 5349-13 frequency weighting) is accomplished using custom circuitry that is directly interfaced with the microcomputer. An embedded C-based protocol governs the data collection from each channel

Jan 6, 2006

By T. G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a porphyry copper sulfide ore. The purpose was to determine the effects on copper leaching of additions of NaCI to a conventional sulfate leach system and to analyze the oxidant requirements and the oxidation products that resulted from leaching of the sulfide minerals in the ore. Baseline sulfate and sulfate plus 2-pct-NaCl-leach-solution experiments employing 167-kg (367-lb) and 152-kg (333-lb) charges, respectively, were conducted. The minus 25.4-cm (10-inch) ore was leached at 90° C under flooded conditions with 2.8 MPa (400 psig) of oxygen bubbling through the system. Sixty-seven pct of the copper was extracted in 1,236 days of leaching in the NaCI experiment, whereas 47 pct of the copper was extracted in 913 days of leaching in the baseline experiment. Diffusion into and out of the ore fragments controlled the rate of leaching, which precluded enhancement of the leach rate by the chloride ions. The calculated oxygen consumption was 3.17 kg/kg of copper extracted in the baseline experiment and 3.46 kg/kg of copper extracted in the experiment to determine the effect of chloride ions.

Jan 1, 1982

By James E. Mills

Coal, in the process of mining, transportation, and handling and on exposure to the weather, is subject to more or less disintegration. This disintegrated coal is usually called "slack" and amounts often to a considerable percentage of the lump coal produced in the mines. If this slack coal is wasted the loss so occasioned ranges from 5 to 50 per cent, or even more, of the total coal mined. It is therefore clear that the utilization of this waste slack coal becomes a serious economic consideration. When the coal is suitable for the production of coke, the utilization of the slack presents no difficulty, as it is in demand for that purpose. If the coal does not produce good coke, but cakes rather readily, the slack can be used for boiler purposes, as it fuses together more or less quickly, and burns on the furnace grate without great loss. Coal that cakes less readily can be burned on grates of special construc- tion. When so used it is more troublesome to handle, and the waste is greater than when lump coal is used. Consequently the price of much of the slack coal for fuel purposes ranges considerably lower than that of the lump coal from the same mine. The full value of this slack coal as fuel can be realized by first form- ing the coal into a coherent mass or briquet, such briquets, when of good quality, being equal to or of greater value than the original

Jan 1, 1911

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997

By David C. Byrne

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals. Also, miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupational Research Agenda, problems created by occupational hearing loss include (1) the reduced quality of life due to social isolation and unrelenting tinnitus, (2) impaired communication with family members, the public, and coworkers,(3) a diminished ability to monitor the work environment (e.g., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers’ compensation and hearing aids. Although the elimination of hazardous noise is the ideal long-term solution to the noise problem, miners will likely need to rely on personal hearing protection in certain situations for quite some time. However, it is well known that noise attenuation provided by hearing protectors as they are worn during everyday use in the workplace is usually worse than when tested under laboratory conditions. Additionally, workers may refuse to wear their hearing protection for any number of reasons. Therefore, this project was initiated to evaluate practical technological advances in hearing protectors, with an emphasis toward optimizing the balance between effectiveness, comfort, overprotection, and communication ability. Currently, the necessary in-house laboratory facilities and research techniques are being finalized. Individual experiments are planned that involve analysis of new hearing protector technology under both laboratory and field conditions. The laboratory components are to consist of con-trolled studies using human subjects and/or an anthropometrically correct artificial test fixture to evaluate the adequacy/effectiveness of various hearing protective devices. Field studies are planned to determine the actual usefulness and practicality of the hearing protectors as used in diferent mining environments. Recommendations can then be offered to the mining community regarding correct earplug/earmuff usage that maximizes recognition of hazard/warning sounds while adequately protecting the miners’ hearing.

Jan 12, 2000

Reduce the hazards to which mine personnel are exposed by providing safer procedures for removing dragline wire rope terminations. Background The termination points of wire ropes used on draglines consist of a wedge and socket that lock the rope in place through friction. These components must be separated when the wire rope is changed. At present, the cannon method is the most common procedure used to accomplish this. However this method, using a small cannon and primer (detonator) cord to propel a steel projectile that will knock the wedge out of the socket, has the potential of causing injuries to mine personnel and damage to equipment. The Bureau of Mines, has devised safer, and equally efficient methods of removing wire rope terminations. The Bureau began by studying the cannon method, its merits and draw-backs. Safety guidelines were then developed for the cannon method, and two alternative methods-the pendulum ram and hydraulic pusher-were devised and tested. The Cannon Method The steel projectile used to separate the wedge and socket in the cannon method was found to be very effective. However, the method poses the inherent hazards of any explosive de-vice-hazards that could be increased by lax work procedures. There is no strict uniformity in the manufacture of the cannon or in the work procedures used in the mines employing it. Hazards could be reduced, or even eliminated, with adaption of certain manufacturing and work-procedure guidelines, such as 1) making the cannon and projectile de-signs, as well the work procedures used, uniform, 2) ensuring separate loading of the charge and detonator with insertion of the detonator through a separate port, 3) connecting electrical firing circuits only after the charge and projectile are loaded and the cannon is placed in its final firing position, 4) using approved detonating devices, 5) anchoring the cannon before firing and, 6) placing armor netting over the cannon before detonation.

Jan 1, 1986

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry and seal manufacturers, conducted a series of full-scale experiments within the underground experimental mine at PRL's Lake Lynn Laboratory. The purpose of the experiments was to evaluate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in less than 12 hours and are capable of withstanding explosion overpressures in excess of 140 kPa (20psi). These novel seal designs use available mine materials, do not require conventional rib hitching and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By A. J. Farstad, R. F. Kehrman

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped driers in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light- weight and inexpensive.

Jan 1, 1979

By Michael A. Trevits

Mine fires can be especially perilous because toxic products can quickly spread well beyond the fire zone thereby exposing all underground miners to dangerous and deadly conditions. Since November 1998, there have been six major underground coal mine fires or explosions in the United States (Willow Creek (twice), Sanborn Creek, Loveridge No. 22, West Elk and the Jim Walter Resources No. 5 Mine). In each case, the entire mine or specific areas of the mine had to be sealed due to the build-up of dangerous gases and the fear of uncontrolled spread of the fire. Effective placement of mine seals can deprive a mine fire of oxygen and is often followed by water flooding or injection of inert gas into the affected area. When access to the fire zone is impossible because of safety reasons, airtight mine seals can be constructed, in the area of the fire, remotely from the surface through vertical boreholes. Remotely constructed mine seals are commonly made from cementitious material. Since these mine seals are typically erected blindly, it is difficult to determine if mine roof-to-floor and rib-to-rib closure has been obtained. This paper provides a review of the available materials and technology used to remotely construct mine seals through vertical boreholes.

Jan 1, 2002

By Eric E. Cather

A mineral investigation by the U.S. Bureau of Mines revealed no mines or prospects and no past or present mining claims in the Agua Tibia Wilderness Study Area (WSA). The area is underlain mainly by weakly foliated gabbro similar to rock that has hosted gem- and lithium-bearing pegmatites in the Pala district about 6 mi to the south. However, no gem- or lithium-bearing pegmatites have been discovered in the WSA. Nearby quarries in the gabbro have yielded rock for facing and dimension stone. No sand, gravel, or energy (oil, gas, coal, or geothermal) resources were identified.

Jan 1, 1984

By John R. Benham

In 1987, at the request of the Bureau of Land Management~ the U.S. Bureau of Mines studied 7,600 and 3,000 acres, respectively, of the Slocum Creek (OR-003-075) and Upper Leslie Gulch (OR-003-074) Wilderness Study Areas in order to evaluate their mineral resources. They are located in Malheur County, OR, about 25 mi northwest of Jordan Valley. Both areas have an occurrence of stone (welded tuff) covering about 3,000 acres which is suitable for construction purposes including road metal, ballast, and road fill. However, similiar deposits are more accessible and closer to markets.

Jan 1, 1988

By Elaine T. Cullen

Safety training materials appropriate for specific underground noncoal operations in the United States are often outdated or nonexistent. The Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and H ealth has developed several new training tools, including three videos on common underground activities, software that will allow trainers to create a virtual training mine using their own mine map, and toolbox training materials. SRL is working closely with industry in the development of these tools. Teams of safety professionals are involved in the early stages, and actual mines and miners are involved throughout the production phase. This presentation describes the development process and results of SRL’s safety training projects.

By Jack E. Fraley

Poor lubrication reduces the life of wire hoist ropes when they are used in corrosive environments. Although lubricants are added to ropes during the manufacturing process, these lubricants can deteriorate during use, and it is often necessary to add more lubricant to both the interior and exterior of the rope while it is in service. The U.S. Bureau of Mines evaluated the effectiveness of synthetic lubricants, using electromagnetic nondestructive testing (NDT) to measure deterioration in ropes while they were in service. For nonpressurized lubricant applications, synthetic lubricants appear superior to petroleum-based lubricants in their ability to penetrate to the interior of a rope. Therefore, the synthetics offer better wear and corrosion protection.

Jan 1, 1990

By Harold W. Lipper

A NEW record was set for helium shipment in 1962 for the 13th successive year. For the first time since 1949, the production of helium from natural gas at Bureau of Mines plants was less than in the previous year. The Bureau shipped 599.5 million cubic feet, 9 percent more than the 1961 volume, and produced 680.9 million cubic feet-a decrease of 6 percent from the record set in 1961. The Bureau added 77.2 million cubic feet to the volume stored for future use. Of the total 524.6 million cubic feet in storage, 522.4 million cubic feet is accumulated excess production from Bureau of Mines plants. The remaining 2.2 million cubic feet was purchased during 1962 from industry under the helium conservation program. The first two of five private plants began production in December to recover helium for conservation storage and ultimate use. A 425-mile pipeline system to transport helium from the five private plants to the Cliffside field was constructed by the Bureau at a cost of about $8 million.

Jan 1, 1963

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Twenty-five years ago, the former U.S. Bureau of Mines funded a research project aimed at developing the enabling technology for incipient failure prediction in electric power system components as a means of reducing the injuries and fatalities that sometimes occur when equipment malfunctions. Over the ensuing years, interest in this has waxed and waned, but recently interest has been growing for both civilian and military applications. This paper addresses the level of turn-to-turn insulation deterioration that can be resolved using an on-line monitoring technique. The detection of turn-to-turn defects is especially important because they are believed to represent the beginning stage of most motor winding failures.

By John J. Sammarco

Mining, traditionally a low-tech industry, is now utilizing surprisingly complex programmable electronic (PE) systems. The functional safety of PE-based mining systems is an international issue and concern. From 1995 to 2001, there were 11 PE-related mining incidents reported in the U.S. and 71 PE-related mining incidents reported in Australia. These incidents are due, in part, to unprecedented levels of system complexity. The National Institute for Occupational Safety and Health (NIOSH) is addressing this issue of system complexity by conducting research to develop a quantitative complexity assessment methodology based on Normal Accident Theory (NAT). The methodology models the behavioral interactive complexity at the level of system requirements. A graph-theoretical approach is used for creating quantitative metrics from Software Cost Reduction (SCR) dependency graphs. This complexity assessment methodology will help realize simpler, safer systems that will be easier to validate and verify. The methodology will benefit mining and other industries as well.