Search Documents

By John C. LaScola

The Bureau of Mines repeatedly surveyed a grid of monuments over an active longwall mine panel in southwestern Pennsylvania during a 1-year period. Both conventional ground surveying techniques and photogrammetry were used. The objective of this investigation was to compare elevation measurements of subsidence obtained from aerial and ground survey methods under dynamic ground conditions. The results of a statistical analysis of the survey data show that the mean of the differences between 372 matched pairs of elevation measurements was 0.20 ft (61 mm) with a 95-pct-confidence interval of 0.05 ft (15 mm). The mean of the absolute values of the differences was 0.38 ft (116 mm) with a 95-pct-con-fidence interval of 0.04 ft (12 mm). Ninety-five percent of the absolute values of the differences were less than 1.11 ft (338 mm).

Jan 1, 1988

By S. H. Katz

Artisans and laborers in mineral industries where the air is dusty with particles of reel: are subject to a peculiar pulmonary disease known as miners' phthisis or stone cutters' consumption. In granite cutters the disease is specifically designated as granite pneumoconiosis. Very fine particles of the harder rocks are especially injurious when inhaled into the lungs. It is estimated particles about one micron (1/23000 part of an inch in diameter) are most injurious, because larger particles are more readily removed by the cilia and,wet surfaces of the respiratory passages before reaching the lungs, while smaller particles either do not readily lodge or are more easily eliminated. Silica, of which quartz and flint are composed, and which forms a large part of granite, is one of the hardest of the common rock-forming materials. It is also very insoluble when silica lodges in the lungs elimination is difficult. Rock constituents of granite other than silica are probably injurious but in a lesser degree, and this is also probably true of limestone and the softer rocks. Ultimately a worker who daily inhales much granite dust has considerable deposited in his lungs. If he continues at his trade the lung tissue becomes harder and less elastic, he finds himself short winded, and in extreme cases death may come either directly or indirectly as a result of lung failure.

Feb 1, 1921

By Martin H. Stanczyk

Freezing to dewater typical Florida phosphate rock slime as demonstrated in laboratory tests appeared to have potential commercial use because of indicated moderate energy requirements, good compaction of dewatered solids, and effective recovery of usable water. After freezing, thawing, decanting, and filtering, batch freezing of gallon-size 13.7 percent solids slime samples yielded 42 percent solids products. Cationic amine, used as a process additive, yielded 46.8 percent solids product with significant filter area reduction. Semicontinuous 8 stage freezing tests also produced thickened slimes. Cooling and freezing 13.7 percent solids slime from 30° to minus 10° C required removal of 183 Btu per pound of slime; Carnot cycle calculation indicated that the theoretical minimum energy to transfer this heat was 27.8 Btu per pound. To produce 1 ton of 44 percent solids slime from 13.7 percent sol-ids slime, the calculated theoretical energy required for cooling and freezing was 52.3 kilowatt-hours. During the research heat capacity and heat of fusion data were determined for the slime at various percent solids.

Jan 1, 1971

By Lisa Steiner, Robin Burgess-Limerick

In 2004, there were 646 underground coal mines in the USA employing 37,445 miners. These mines reported 3556 injuries to MSHA that year - 17% were associated with bolting machines (593 injuries), 8% with continuous miners (283 injuries), and 4% each with Scoop/LHD (1 51 injuries), shuttle cars (134 injuries), and personnel transport (145 injuries). The use of the frequency of reported injuries for the prioritization of risk control strategies has limitations because of the tendency to underestimate the importance of relatively rare but high-consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggest the following hazards as the highest priority for elimination or control: • rock falling from supported roof • inadvertent or incorrect operation of bolting controls • handling continuous miner cable • collisions while driving LHD/Scoop, shuttle cars and personnel transport • rough road while driving or traveling in LHD/Scoop, SC & PT

By J. D. Marchant

As part of its mission to assure the maximum recovery and use of the Nation's mineral resources, the Bureau of Mines, investigated an improved procedure for producing rare earth-silicon alloys. For example, a charge consisting of 681 grams of mixed rare-earth oxides, 309 grams of ferrosilicon (75 wt-pct Si), and 182 grams of aluminum metal along with a flux consisting of 681 grams of CaO and 45 grams of MgO was reacted at 1,500° C in an induction furnace. Good slag-metal separation was achieved. The alloy product contained, in weight-percent, 53 RE, 28 Si, 11 Fe, and 4 Al with a rare earch recovery of 80 pct. In current industrial practice rare earth recoveries are usually about 60 pct in alloy products that contain approximately 30 wt-pct each of rare earths and silicon. Metallurgical evaluations showed the alloys prepared in this investigation to be as effective in controlling the detrimental effect of sulfur in steel and cast iron as the commercial rare earth-silicon-iron alloys presently used in the steel industry.

Jan 1, 1980

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

5. General Escapeway Requirements 5.1 Escape Routes Present escapeway regulations state "Every mine shall have two separate properly maintained escapeways to the surface which are so positioned that damage to one shall not lessen the effectiveness of the other, or a method of refuge shall be provided when only one opening to the surface is possible." "Escape routes shall be a. Inspected at regular intervals and maintained in safe, travellable condition, b. Marked with conspicuous and easily read direction signs that clearly indicate the ways of escape." "Application. "Regular" intervals means at intervals no greater than monthly where conditions are stable and oftener where conditions may change." "Designated escapeways inclined more than 30* from the horizontal shall be equipped with stairways, ladders, cleated walkways, or emergency hoisting facilities." As can be noted in present and proposed regulations there must be two separate properly maintained escapeways. In most operations, the escapeways will consist of one route that is the normal travelway used in day to day operations. The second route is usually a return airway through old work areas. Based on this generally accepted practice, we will designate the two types as primary and secondary.

Jan 1, 1976

By H. B. Freeman, E. J. Gleim

During the 12 months ended July 1, 1931, engineers of the Bureau of Mines examined electrical equipment in 80 bituminous-coal mines. The purpose of these examinations was to ascertain the condition of such equipment with respect to possible hazards of gas and dust ignitions, also of shock. Although only 3 of the 80 were being worked with open lights and therefore did not use explosion-proof equipment, there were others where electric cap lamps were used by the men but where it was apparently assumed that conditions as to gas and dust did not require equipment designed to give protection against ignitions. Early in its history the United States Bureau of Mines originated certain standards covering the construction and testing of electrical equipment in order to minimize the dangers of ignitions from exposed electric sparks and flashes ; accordingly, it is comparatively easy to determine wherein a machine built to these standards falls short of continuing to meet them if damaged or neglected. Many so-called flame-proof and dust-proof machines, however, have not been built to any standard comparable with that developed by the Bureau of Mines. In addition, certain machines have parts which pass Bureau of Mines tests, but do not satisfy the full requirements in other respects, and others make no pretense of inclosing the spark-producing parts. It is not uncommon to find two or more of these various types in the same mine with " permissible " machines, the type that has been built to conform to the Bureau of Mines standard. Consequently, inspection of nonpermissible machines becomes somewhat difficult without a standard of comparison. Because of its unprotected condition obviously open-type electrical equipment must be used with great care, if at all, in a mine where precautionary measures are adopted in guarding against gas and dust ignition. The unsafe nature of such equipment is widely recognized. For that reason it is to be installed only where there is no likelihood of gas being present. It is not apparent to some, however, why flame-proof and dust-proof equipment and equipment having tested parts should not be regarded in the same light as permissible equipment.

Jan 1, 1932

By Joseph A. Holmes

The perpetuation of the supply of anthracite coal in Pennsylvania is a national as well as a State problem. Any investigation that shows how larger percentages of this coal may be saved in mining, without excessive cost, and without dangerous subsidence of the overlying surface ground, has a national as well as a local interest. Messrs. Conner and Griffith, who conducted the investigations described in this report largely for the city of Scranton, are consulting engineers for the Bureau of Mines for investigations similar to those they have already made in connection with their Scranton work; and this report is published by the bureau in response to numerous requests, because of the fact that the information it contains will prove useful in the general solution of similar problems in many of the country's coal fields. A study of the accompanying maps will show that the city of Scranton is underlain by 11 separate beds of coal, varying in thick- ness from 2 to 24 feet. It is estimated that before mining opera- tions were begun these beds of coal contained underneath the present city limits of Scranton 600,000,000 tons of coal. The 27 collieries operating within the city limits, working independently of each other, had excavated and removed, up to March, 1911, an aggregate of 198,000,000 cubic yards of coal and accompanying rock, or 3,000,000 cubic yards more than the total amount of material excavated and to be excavated by the United States in constructing the Panama Canal. This fact illustrates something of the magnitude of the problem that the city of Scranton, with the aid of these engineers and of a special commission or advisory board, has undertaken to solve. The excavation has included 177,000,000 tons of coal and 44,000,000 tons of rock and accompanying refuse. This leaves about 420,000,000 tons of coal still to be removed. As a result of other investigations and of experience in adjacent anthracite mines, Messrs. Conner and Griffith and the advisory board of engineers have advised that, as far as may be necessary to prevent dangerous surface subsidence, the spaces remaining beneath the city of Scranton from the excavation of the above-described material should be filled with sand and other materials by flushing or other processes. This operation is expensive, but it is believed to be not beyond the reach of what is practicable, nor in excess of the value of the coal that may be removed and the amount of damages that may result from the caving in of the surface if such a plan is not carried out. No one realizes so fully as do the authors of this report the need of additional tests and other investigations before the data now pre- sented by them can be fully accepted as sufficient for all purposes in the solution of the problem; and it is expected that at some early date a more extensive series of similar tests can be made by the Bureau of Mines under the supervision of Messrs. Conner and Griffith on a larger scale and under a greater variety of conditions. The field examinations made for the Bureau of Mines by N. H. Darton, which are described briefly in a chapter of this bulletin and will be discussed at length in a bulletin to be published later, indicate the extent and distribution of the sands, gravels, and other materials in the Scranton-Wilkes-Barre district available for flushing purposes if further tests indicate their relative merits; and it is expected that the relative merits of these different materials will soon be tested under such conditions as will furnish the desired information.

Jan 1, 1912

By Thomas G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a chalcopyrite ore. The purpose was to obtain a direct comparison between moderate-temperature and elevated-temperature in situ leaching of copper trom minus la-inch ore and to analyze the sulfuric acid and oxygen requirements of the leaching system. Experiments employing oxygen were conducted at 35° and 90° C on 362-and 367-1b ore charges, respectively, under flooded conditions and at 400 psig. At 90° C, 47 pct of the copper was extracted in 913 days of leaching; at 35° C, 27 pct of the copper was extracted in 915 days. Diffusion into and out of the ore fragments con-trolled the rate of leaching. Oxygen consumption was 1.46 lb/lb of copper extracted at 35° C and 3.15 lb/lb of copper extracted at 90° C. Sulfuric acid requirements of the ore were 5.49 and 7.48 lb/lb of copper extracted at 35° and 90° C, respectively.

Jan 1, 1982

By R. L. Crosby

The effect of indium on the solid solubility of calcium and of silicon in magnesium was studied using metallographic, X-ray diffraction, and electrical resistivity techniques. The addition of 2 weight-percent or more of indium reduced the solid solubility of calcium in magnesium by forming a compound containing indium and calcium. Indium additions have no perceptible effect on the solid solubility of silicon in magnesium.

Jan 1, 1963

By Burke Cartwright, S. F. Ravitz, Lloyd R. Michaels

This method is similar to the reduction of dolomite by ferrosilicon, in that it does not require the direct use of electrical energy; like ferrosilicon, the calcium carbide must be produced in an electric furnace, so that the reducing agent in both processes may be considered in some respects as “stored” electrical energy. The reduction of magnesium chloride by calcium carbide is exothermic, takes place rapidly at ordinary pressure and at relatively low temperatures, and can be carried out in ordinary steel equipment, whereas the reduction of dolomite by ferrosilicon and the carbothermic reduction of magnesium oxide are endothermic, require high temperatures, and present serious problems with respect to materials of construction. Because of its apparent simplicity and other advantages, the Bureau of Mines has briefly investigated the reduction of magnesium chloride by calcium carbide. Published data on the reduction of magnesium chloride by calcium carbide are meager. Matignon states that reduction is fairly rapid at 1,200º C. Matsuura claims that magnesium chloride is not reduced by calcium carbide at atmospheric pressure and 800º C; however, by keeping the pressure under 10 mm. of mercury he was able to obtain small globules of magnesium at 800º C.

Mar 1, 1947

By M. G. Zabetakis

The method of moving averages was found useful in assessing the nature of methane emission in coal mines. Emission rates were influenced markedly by the presence of abandoned oil and gas wells in the vicinity of the mine. Such wells appeared to increase the flow rate of methane into the mine by a factor of 2 to 30 in an active mine in the Pittsburgh coal seam.

Jan 1, 1972

By L. B. Berger, W. P. Yant, R. R. Sayers

"At the request of the Chesapeake & Ohio Railroad Co. a number of tests were made to determine the temperature, humidity, and composition of the atmosphere in certain tunnels of that railroad between Clifton Forge, Va., and Hinton, W. Va. The purpose of these tests was to determine conditions in the cabs of freight locomotives while pulling trains through these tunnels. Tests were made of two types of locomotives, classified by the railroad company as the H-6 and H-7. Both are of the Mallet type, but the H-6 class has one pair of cylinders operating at boiler pressure and the other pair compound, whereas the H-7 operates all four cylinders at boiler pressure, thereby exhausting steam at a higher temperature than the H-6. It was desired to determine the relation between conditions on the H-6 and H-7 engines under comparable conditions of operation. This information supplements previous tests by the Bureau of Mines, discussed in its Reports of Investigations Serial No. 2624, entitled, ""Temperatures in Cabs of Freight Locomotives Passing Through Tunnels of Chesapeake & Ohio Railroad, 11 by s. H. Katz and E. G. Meiter, July, 1924. Three incidental tests of passenger engines were also made."

Feb 1, 1928

By N. F. LeJeune, Earl C. Lane

This is the third of a series of reports on a survey of petroleum prod- ucts manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in the other parts of the United States, and the claim has been made that some of the present Federal Specifications for petroleum products tend to discriminate against Cali- fomia products. The purposes of the present survey are to determine what par- ticular specification requirements Califomia petroleum products characteristical ly fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what lines investigation to determine this question should proceed. The first report of the series gave the physical and chemical properties of the samples of gasoline and mineral spirits. A second report**, gave the physical and chemical properties of samples of lubricating oils. The present report deals entirely with burning and fuel oils. The refin ing companies have continued their very cordial and helpful cooperation. Seven samples of kerosene, four samples of Diesel fuel and eight samples of fuel oil were obtained. The methods of analysis used are those adopted by the Interdepartmental Petroleum Specifications Committee, published by the Bureau of Mines in Technical Paper No. 323. The specifications used for corparison are those officially adopted by the Federal Specifications Board for the use of the various Depart- ments and Independent Establishments of the Government, effective February 3, 1923, and published by the Bureau of Mines in Technical Paper No. 323, Part 1. Specific gravity, degrees A.P.I., viscosity and other special tests al- though not required by the specifications have been given for comparison. All temperatures are recorded in degrees Fahrenheit. Tables have been prepared giving data on physical and chemical propertios of the individual samples. Before each table the classification and specifica- tions for the particular class of oil considered in the table are given. Follow- ing each table, brief notes show wherein samples deviate from specification re- quirements.

Aug 1, 1923

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Beaver and Lawrence Counties, Pa. Washability analyses were made on seven coalbed samples, none of which were of metallurgical quality as received. Five of the samples could be sufficiently upgraded to produce acceptable products, and the remaining two samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, one sample was of low sulfur content as received, one sample could be upgraded to low sulfur content, and three samples could be upgraded to medium sulfur content. The original sulfur content of the remaining two samples can be appreciably reduced by removal of the sink 1.58 speci fic gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1969

By F. N. Kissell, R. J. Bielicki

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about 1 part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

By E. Chin

The mineral industry of Bangladesh was totally dominated by natural gas production and its downstream uses. A small amount of cement was produced, and clays were used locally for ceramics and construction materials. Nitrogenous fertilizer was produced from natural gas and a modest, scrap-based steel industry produced steel for local consumption. The country has been developing and using its abundant and inexpensive gas reserves as fast as practical. The population, however, was predominantly dependent on agriculture for its livelihood. The industrial sector accounted for 10% of the economy, and most of the industrial output was directly associated with agricultural products jute, tobacco, and textiles. Industrial expansion, even with the availability of gas, was severely constrained because of limited domestic demand, lack of skilled work force and management, poor infrastructure, and a low rate of domestic savings. To put greater emphasis on the industrial sector, the Government established a National Committee for Industrial Development in July. The Committee instituted policy reforms in the areas of trade and investment. One important step was to move from a positive import list to a negative list, thereby permitting imports of items not restricted or banned. The system for recovering and approving new domestic or foreign industrial investments was streamlined to expedite what had become a cumbersome, bureaucratic exercise. To encourage industrial development in areas away from the crowded urban centers, several economic incentives reportedly were adopted. These included a reduced tax rate on imported machinery, exemption of import license fees, a reasonable debt equity rate, and a 9-year income tax exemption period.2 In the trade sector, imports increased 12% in fiscal year (FY) 19843 mainly

Jan 1, 1987

By Gregory M. Molinda

The Bureau of Mines conducted an investigation into the occurrence of outbursts of salt known to be responsible for explosions, fatalities, and damage in domal salt mines. The purpose of the investigation was to develop a basis for predicting these outbursts based on geologic and associated physical properties of salt. The investigation was conducted at the Cote Blanche salt mine in southern Louisiana. Because outbursts are the primary mode of methane emission into the mine, more than 80 outbursts, ranging in size from 1 to 50 ft in diameter have been mapped. These outbursts generally are aligned and elongate parallel to the direction of salt layering. More than 200 salt samples, both random and selected, were tested for methane content. It was found that outburst zones are well correlated with high methane content. Detailed mapping also revealed that the zones are well defined, with salt crystal size abruptly increasing upon entry into the zone. The intensity of folding and kinking of the salt layering within the outburst zone also appears to increase. An interbedded sand layer occurring throughout the mine does not appear to be a significant source of methane. However, fine-grained salt may be related to outburst occurrence.

Jan 1, 1988

By Jon K. Ahlness

The Bureau of Mines, in cooperation with the Institute of Mineral Research of Michigan Technological University, and the Upper Great Lakes Regional Commission, conducted an investigation of electronic sorting of native copper ore from Upper Michigan. This report is based on research by the Institute of Mineral Research under contract to the Bureau. The test program evaluated the use of belt and rotary sorters on various size and grade fractions of ore. Both plant-scale sorting and lab sorting tests were run. The plant sorting objectives were to determine the sortability of different ores and the efficiency of the electronic ore sorters. High-and low-grade ores from both conglomerate and amygdaloid types were separated into four size fractions. The two larger sizes were sorted on belt sorters and the two smaller ones on rotary sorters. Copper recoveries ranged from 20.0 pct from a feed grade of 0.40 pct to 80.3 pct from a feed grade of 1.08 pct. Lab sorting tests of conglomerate ore were run to determine the efficiency of a belt sorter equipped with a second sensing coil located above the belt and to determine the sorting characteristics of larger ore size fractions than those used in the plant sorting. Copper recoveries from the combined feed sizes ranged from 47.0 pct from a feed grade of 0.13 pct to 96.8 pct from a feed grade of 4.87 pct. For all the ore types except one, it was found that the copper recovery increased with the feed size.

Jan 1, 1980

By William P. Diamonds, David C. Oyler

Stimulated vertical boreholes are an effective means of removing gas from coalbeds in advance of mining. This Bureau of Mines report examines the coal mine roof damage potential of stimulation treatments. Twenty-two Government-sponsored stimulation treatments have been mined through to determine the effects on the coalbed and roof strata. Vertical fractures in the coalbed were discernible for most treatments and horizontal fractures were present for about half of the stimulations. Sand-propped vertical fractures were usually short in lateral extent. Evidence of stimulation fluid movement could generally be traced beyond the maximum extent of sand-filled fractures when fluorescent paint was added to the treatment fluids. The maximum lateral extent for a sand-filled vertical fracture was 416 ft and a paint-coated vertical fracture extended 630 ft. Horizontal fractures were generally found within bedding planes, most commonly on top of the coalbed. The maximum lateral extent for a horizontal fracture was 265 ft at a coalbed depth of 630 ft. Horizontal fractures have been found to occur as deep as 1,145 ft. Penetration of strata overlying coalbeds was observed in nearly half of the treatments intercepted. Most of these occurrences have been interpreted to be penetrations into preexisting joints. No roof falls or adverse mining conditions were encountered that could be attributed to the stimulations.

Jan 1, 1987