Search Documents

By Jack A. Touseull

The Bureau of Mines has developed a simple stereographic method of analyzing the orientation of single and intersecting planes of weakness in vertical pillars of parallel symmetry. From this method, it can be determined if planes of weakness transect the full horizontal cross section of a pillar. A major finding resulting from this method was that intersecting planes of weakness can transect the full horizontal cross section of a pillar even though the individual planes do not. This paper provides step-by-step instructions for using this method.

Jan 1, 1977

By R. Karl Zipf

Use of Salamon's stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon's stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

By J. Hanslovan, R. H. King

An investigation of the feasibility of shielding low-voltage trailing cables in underground coal mines is described. Both laboratory and under¬ground installation results are presented. The main objective of shielding is to reduce the electrical shock hazard; however, several problems will be encountered by mine operators who install shielded cables. Parameters related to such items as purchasing, splicing, troubleshooting, safety, and reliability are discussed. Some of these problems can be minimized by changes in cable constructions and shuttle-car reeling-device components. Both SH-C and SH-D constructions are considered.

Jan 1, 1979

Permit visual inspection of underground cavities dam the surface. Approach A closed circuit TV camera and a 35mm still camera are lowered down a borehole, and remotely operated. How It Works A platform holding the cameras, and other equipment is lowered on a graduated cable until the depth of interest is reached. Then a quartz lamp and the TV camera are turned on. The television picture is monitored at the surface and recorded on video tape. Areas of special interest are photographed with a 35mm still camera. These photographs contain more detail than TV images because photographic film is capable of higher resolution than a TV transmission.

Jan 1, 1979

By J. R. Thoenen

This circular is part IV of the third paper (entitled "Sand and Gravel Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part I discussed the use of power shovels, draglines, and excavator cranes; part II discussed the use of power scrapers, slackline cableway excavators and hydraulic monitors; and part III discussed the use of hydraulic, clamshell, ladder, and dipper dredges. This circular discusses haulage equipment in general, particularly the use of industrial cars with locomotives or hoists as the motive power. Part V, to follow, will discuss the use of other types of haulage equipment.

Oct 1, 1935

By A. L. Engel

This report describes laboratory-scale experimental treatment of six base-metal ore samples taken by engineers of the Bureau of Mines, Region II, while investigating ore deposits in California and Nevada. The information is of interest in developing the mining districts represented or when similar ores from other sources are being studied. Simple treatment methods were employed as far as possible. More complex treatments also were tried when necessary. The possibilities and limitations of the methods applied to the several ores are shown by the data herein reported.

Jan 1, 1960

By C. R. Kindall

Recently 30 men wore viewing the demonstration of a now portable electric arc-welding outfit. A few hours later 17 of the 30 men reported to the doctor for treatment. They were suffering from traumatic conjunctivitis. In two cases the gain was very severe and the symptoms were similar to those of iritis. orphine had to be administered to afford relief from pain. Only two men of the 30 wera not affected in some way from this exposure. These two men were thick-lensed orange-colored glasses. Several of the men wore orange-colored glasses with thin lenses, but the latter were not heavy enough to afford protection.against an exposure as long as took place. The distance of the eye from the are also in- fluences the possibility of injury. Conjunctivitis is an inflammation of the con- junctiva; the conjunctiva is the mucous membrane covering the inside of the eye- lids and part of the eyeball. Traumatic conjunctivitis is caused by foreign bodies in the eye, exposure of the eyes to high winds, dust, smoke, intense light from electric arc lamps, and from electric welding apparatus. In the instance mentioned above, the inflammation was due to the ultra-violet rays. The ultra-violet rays lie beyond the violet rays in the spectrum and are invisible to the eye. In some cases the effect is so severe that, in addition to conjunctivitis, an inflammation of the skin similar to sunburn is produced. The symptons of conjunctivitis caused by intense light or by the ultra- violet rays are marked photophobia (abnormal intolerance to light), excessive secretion of tears, intense starting of the lid, contraction of the pupil, some- times swelling of the lid, and small ulcers developing on the eyeball or cornea. Unless properly treated by a physician immediately, chronic inflammation of the conjunctiva, cornea, iris, or retina, and possibly blindness, may result. Under proper treatment most cases get wall in a few days. All treatments should be under the direction of a physician. That usually advised is to place ice packs on the patient's eyes three or four times daily. The pack should be left on from 15 minutes to an hour. The eyes should be irrigated with normal salt solution (a teaspoonful to a quart of sterile vater) or a saturated solution of boric acid several times daily. If there is a discharge of pus, a few drops of a 25 per cent solution of argyrol or a 5 per cent solution of protargol should bo placed in the eyes three to six times daily. The patient should be confined to a darkened room until his condition improves in order to avoid complications. These treatments will reduce the swelling, give the patient confort, and prevent the development of chronic conjunctivitis. In severe cases it may be necessary to administer morphine to relieve the pain.

Oct 1, 1920

By C. P. Hood

"The amount of ash in anthracite coal interests every buyer, and occasionally produces caustic comment, but there is a lack of authentic figures that will take the subject out of the realm of opinion and agitated fancy and. give a true picture of the quality of coal actually delivered. What per cent ash is to be expected when the coal is good, and when have we a right to make serious complaint?During the past summer the Bureau of Mines took 127 samples of 1000 pounds each, representing nearly 30,000 tons of anthracite is dealers' yards in seventeen cities in the State of Massachusetts. There were three objects in view, to discover the average and the variation in amount of ash in anthracite in some easily described area; to demonstrate standard sampling methods, and to learn something about the feasibility of itinerant coal sampling. Massachusetts was selected because its principal cities could be visited in a single season. There also appeared need for demonstration of standard sampling of coal, since a coal quality law had been passed in the State, to be administered by those unfamiliar with coal sampling."

Feb 1, 1924

Reduce the airborne dust generated in a longwall coal face. Approach Reduce the rotational speed and increase the depth-of-cut of the longwall shearer. How It Works An Anderson-Mavor AM500 double-ended ranging drum shearer was fitted with drums specially designed to accept the large picks required for this testing program. Change gears In the shearer allowed rotational speeds of the drums to be set at 35, 45, 55, or 70 rpm. As deep cutting removes larger coal fragments, the specific energy requirements of the operation are reduced and less surface area results. Dust generation and shearer power consumption are also reduced. The lower rotational speed minimizes the fanning action of the cutterheads and thus reduces the amount of coal fines that become airborne.

Jan 1, 1981

By Fred N. Kissell

Tracer gas decay curves were experimentally obtained in a full-scale model coal mine working face area. The concentration of tracer gas was found to decay in exponential fashion but with a change in slope. This change in slope is attributed to eddy zones in the face area. A simple theory was developed that allows one to calculate the approximate amount of gas in the eddy zones and thus estimate the size of the eddy zones.

Jan 1, 1974

Reduce dust generated during bagging at minerals processing facilities, such as silica sand operations. Approach Installation of a new type of bag nozzle system eliminates the major dust sources during the bag filling process. How It Works The drawing illustrates components of the new bag nozzle system. The system differs in several ways from the conventional nozzle system. An improved bag clamp reduces the amount of blow-back during bag filling, because it has direct contact with approximately 80 per-cent of the nozzle. A two nozzle arrangement includes an inner or "fill" nozzle surrounded by another nozzle, which is designed to exhaust excess pressure from the bag after it has been filled. The exhaust is powered by an eductor, which uses a venturi effect to exhaust the bag at approximately 50 cfm. The exhaust exits into a bucket elevator and is recycled. A pinch valve automatically opens and closes the exhaust system to the bag.

Jan 1, 1984

Provide an accurate, simple, alternative means of evaluating the safety of mine electrical ground systems which has little or no negative impact on mine productivity. The Traditional Evaluation Method The Code of Federal Regulations requires all mines to safely ground their power systems to earth. Effective earth grounding reduces shock hazards to mine workers operating electrical equipment, protects equipment from damage by voltage transients, and provides a means of detecting and locating ground faults. Once an earth ground bed has been constructed, its level of resistance has traditionally been used to gauge the safety of the entire grounding system. Bed resistance measurements are normally performed using a ?fall of potential? technique with a current return electrode placed at a remote location, If the resistance measured is acceptably low, then the bed is assumed safe.

Jan 1, 1985

By E. K. Stanek, P. Kantabutra, R. A. Wolf

This paper summarizes the cause and effect of induced voltages in multiple conductor cables supplying alternating current power to equipment in under- ground coal mines. The investigation of this phenomenon revealed that the electrical energy produced by the resultant electric arcing between the frames of mobile electric face equipment was of a sufficient magnitude to ignite explosive methane-air mixtures. The results of laboratory tests and field tests made between equipment frames during actual operation in numerous coal mines are discussed. Several methods of eliminating or suppressing the induced voltages to nonincendive levels are also described. It is the purpose of this paper to convey to the mining industry a knowledge of this problem and to recommend methods of eliminating or reducing these induced voltages or arcing currents to safe levels.

Jan 1, 1975

By J. Nielen van der Merwe

The move toward partial pillar extraction versus full pillar extraction has necessitated a new approach to underground section stability. When pillars are mined too small to support the weight of the overburden, they will, in some cases, remain stable for a considerable period; in other cases, they will collapse unexpectedly and violently. There is no discernable difference between the pillar safety factors of the failed and stable cases. The explanation lies in the characteristics of the overburden layers. A method is proposed that recognizes the overburden characteristics in the evaluation of stability. Two stability factors are calculated: one for the pillars, the other for the overburden. Using this method, it is possible to make use of the bridging capabilities of overburden layers to prevent pillar collapse. It is possible to scientifically design partial pillar extraction layouts that will be safe. Using energy considerations, it is also possible to prevent violent failure of pillars.

Jan 5, 1999

Determine the dust reduction capabilities of various bag valves available to the minerals processing industry. The Problem Many different types of ground mineral products are packaged into 50-and 100-lb paper bags. Although bag technology is continually improving, dust contamination from bags still remains a significant problem for workers. The greatest source of dust is the bag filling valve. Ideally, the bag filling valve should close after it fills the bag with the ground mineral product. However, the valve usually fails to close properly since some mineral product gets trapped inside the valve during filling and ejection. As a result, when the bag has been filled and falls from the fill station, a rooster-tail of product is discharged from the bag valve. As the bag hits the conveyor belt, additional product discharges from the bag valve. The dust from these sources contaminates the air inspired by the workers filling the bags as well as the work area. Dust also clings to the outside of the bag, contaminating the pallet loading station. Because the various commercial bag valves are composed of different materials, a dust analysis was performed on five of these valves to determine their dust reduction capabilities. The five valves analyzed were: standard paper, polyethylene, extended polyethylene, double trap, and foam.

Jan 1, 1986

By Joseph E. Matta, John C. LaScola, Fred N. Kissell

The Bureau of Mines investigated coal storage silos to determine how gassy coal must be for methane accumulations in a silo to become hazardous and where such accumulations are likely to occur. Methane concentrations were measured in the open space above the stored coal pile, in the pile, and in the reclaiming area. No methane layering was found in closed-top silos. Reclaiming areas were as gassy as the top part of the silos. Coal samples were collected from the conveyors entering the silos in order to assess the gassiness of the coal. No simple correlation was found between the gassiness of the coal stored and the measured methane concentrations. However, at mines where the average 24-hour gas emission from the conveyor belt samples was 14 ft3/ton or more, fans or open tops were used. It appears that a large fraction of the methane released during storage remains in the void space between the coal particles.

Jan 1, 1981

By Forrest T. Moyer

THE SAFETY record of the mineral and mineral-fuel-mining-and-processing industries retrogressed slightly in 1964, as indicated by the 3-percent increase in the frequency rate of all injuries. A slight improvement in the fatality rate was more than offset by the less-favorable rate of occurrence of nonfatal injuries. The overall-operating activity of these industries was lower in 1964 as measured by slight declines in employment and total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 18.00 per million man-hours. This overall rate in 1964 comprised frequencies of 0.29 for fatal injuries and 17.71 for nonfatal work disabilities, which compared with respective rates of 0.30 and 17.20 in 1963. Fatalities totaled 538 or 30 less than in 1963. However, the total nonfatal disabilities of 33,151 in 1964 was 492 higher than in the preceding year.

Jan 1, 1965

By J. R. Katan, J. R. Ball, Peter R. Bannister, F. J. Williams

During the last week in March and the first week in April, 1973, the Naval Underwater Systems Center measured the 76 Hz magnetic field strength (in Wisconsin and Texas) produced by both the elevated and (newly installed) buried Wisconsin Test Facility (WTF) north-south (NS) antennas. The principle result obtained from these measurements is that there is no measurable difference in performance between the WTF buried and elevated NS antennas.

Jan 1, 1973

By Robert W. Freedman, Benjamin I. Ferber, Wayne H. Duerr

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By Robert A. Bruce

A motion transducer based on coherent mixing of laser light backscattered from rough surfaces is evaluated in terms of sensitivity, bandwidth and range. Tests made with a prototype composed of a 4-mw HeNe laser, a silicon avalanche photodiode, and a 15-cm aperture telescope demonstrate that remote measurements with reasonable bandwidth and accuracy are feasible at distances up to 100 meters.

Jan 1, 1977