Search Documents

By Dennis Dolinar, Russell Frith, David Oyler, Christopher Mark

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures. the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used

By A. B. Cecala

A cooperative research effort was established between the Tilden Mining Company LC, the United Steelworkers of America, and the National Institute for Occupational Safety and Health to lower respirable dust levels in an iron ore grinding and concentrator plant. This cooperative effort involved three field studies to evaluate different techniques to lower respirable dust levels. The greatest impact on lowering respirable dust concentrations throughout this facility was achieved through ventilation changes. The most significant improvement was realized by changing the ventilation profile throughout the entire facility. The ventilation to this grinding and concentrator facility was provided by approximately 40 roof fans operating in either the intake or exhaust mode. The operation of these fans was significantly changed in an attempt to pro-vide more of a directional flow pattern throughout the facility, as well as to more closely balance the intake and exhaust air volume. This change accounted for a 31 pct reduction in respirable dust levels in the primary grinding area of the mill. Another successful modification was to improve the sealing of a reclaim tunnel to the outside and by barricading the access point from the reclaim tunnel to the concentrator plant. This minimized the dust liberated in the conveyor tunnels from traveling through the reclaim tunnel and into the plant. These two modifications illustrate the impact that improvements in ventilation can have on lowering respirable dust concentrations in iron ore processing facilities.

By Edward McHugh, Jami M. Girard, Stanley M. Miller

A computer analysis of bench stability has been developed to account for multiple occurrences of potential slope-failure modes in discontinuous rock masses. Bench-scale plane shears and tetrahedral wedges are simulated and stochastically analyzed to estimate the probability of retaining specified catch-bench widths. This geotechnical information is useful in designing bench configurations to improve pit-slope stability and help alleviate rockfall hazards.

By E. J. Babcock

The existence of vast deposits of lignite in the West Central and Western States is well known, although the extent and importance of the deposits have not been appreciated, nor has there been an adequate economic utilization of the deposits. The work of the Bureau of Mines, the United States Geological Survey, and the State geological surveys is disclosing an increasingly large area, underlaid with this kind of coal. Among the States having the largest workable deposits may be mentioned North Dakota, Montana, Wyoming, Colorado, and Texas, and in several other Western States lignite occurs in smaller areas. In North Dakota alone it is estimated that the deposits cover approximately 32,000 square miles, many of them being 10 to 15 feet thick and capable of producing in all several hundred billions of tons of lignite. When one stops to consider what these figures mean as to the immensity of these deposits in the West, it is not strange that people are seeking to ascertain better means for deriving larger benefits from the proper utilization of those great deposits. Consequently, any proposed methods of utilization that are promising are well worthy of careful consideration.

Jan 1, 1915

By James J. Hanslovan

Stresses that damage coal mine trailing cables were investigated to obtain a quantified description of cable-stress locations, magnitudes, and frequency of occurrence. Stresses occurring in operating mining sections were measured and observed. Answers to questions that arose during the underground investigations were pursued under controlled conditions, both in the field and in the laboratory. Cable-handling suggestions that minimize or eliminate the stresses are summarized in the form of recommendations to mine operators.

Jan 1, 1979

By Andrew B. Cecala

While various types of equipment are used in bulk material processing plants to control respirable dust, the equipment often doesn't adequately protect workers. One cost-effective way to supplement your existing dust control equipment is to install a whole-plant ventilation system. This article outlines research by the National Institute of Occupational Safety and Health (NIOSH) on using whole-plant ventilation in two mineral processing operations to reduce respirable dust levels. Information also covers how to design a ventilation system for any bulk material processing plant.

By Albert W. Deurbrouck

Dense-medium cyclone tests in 4-and 8-inch-diameter units have shown the ability of cyclones to make sharp separations down to 100 mesh when washing coals of a finer top size than normally fed to dense-medium cyclones. The reduced top size of the feed apparently allows the finer size particles to report to the proper product by reducing the effect of very coarse particles in the congested separation zone of the dense-medium cyclone.

Jan 1, 1974

By W. M. Merritts, Charles Findlay, Stephen Krickovic

Methane emission rates were studied in a Pittsburgh coalbed mine in northern West Virginia. A fullface boring-type continuous miner, equipped with a methane monitor, was used in the development of a set of eight main headings, one side of which was near old workings; the other side abutted virgin coal. Two air splits ventilated the section. Air volumes and methane percentages were recorded, and time studies of the miner were made during five consecutive operating days, during which a complete cycle of mining the headings and one line of related breakthroughs was accomplished. Methane emission rates increased significantly as mining progressed from the side near old mine workings toward the virgin area, and generally increased with coal extract ion. Mining in the heading immediately adjacent to virgin coal was interrupted quite frequently, owing to excessive methane concentrations at the face, despite adequate air volumes and acceptable methane concentrations in the immediate return airway.

Aug 1, 1970

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

 Previous reports of this series/7/8/ presented data on the composi- tion of exhaust gases produced by Diesel engines operating under various conditions possible in underground workings. In all previous experiments, the engines tested were in proper mechanical condition; that is, they were adjusted and maintained in accordance with the manufacturer's instructions. In discussing the results of these tests in relation to the use of Diesel engines underground, the importance of maintaining engines in proper mechanical condition was emphasized, although no data were presented to indicate the effect of engine maladjustments on production of harmful and objectionable constituents of exhaust gas. It is the purpose of this report to present such data and to reemphasize the importance of adequate maintenance for Diesel engines used underground.

Apr 1, 1943

By Ralph B. Adair

The Bureau of Mines conducted laboratory batch and small-scale continuous tests on samples of silt from the Nolichucky Reservoir near Greeneville, Tenn., to develop a process for the recovery of commercial-grade muscovite concentrates. Using a combination of Humphreys spirals for preconcentration followed by cationic flotation, 94.5 percent of the muscovite was recovered in a product containing 96.5 percent muscovite.

Jan 1, 1971

By E. Morrice

The effect of the temperature of SmF3-LiF electrolyte on the electrolytic preparation of samarium-cobalt alloy by the consumable cathode technique was investigated. The temperatures of the cathode zone, alloy collection zone, and samarium oxide (Sm203) feed zone had to be controlled carefully to obtain a satisfactory samarium-cobalt alloy product. Any appreciable deviation from certain temperature values adversely affected yield and product quality.

Jan 1, 1971

By R. V. Lundquist

Past reports by the Bureau of Mines have described the extraction of alumina from numerous aluminum silicate materials by the lime-soda sinter process. The results from pilot-plant investigations of six materials, with alumina-to-silica mole ratios from 0.3 to 8.7, indicated a relationship between the alumina-silica ratios and the processing characteristics of the sinter. A series of laboratory tests was conducted to define this relationship. Sinter and leach tests determined that an alumina-to-silica mole ratio of 0.90 or greater resulted in the best alumina and soda recoveries while leaving the leach slurries practically free from any tendency toward gelation. The widely different chemical and mineralogic properties of the various aluminous materials used in compounding the mixes had no perceptible effect on the leaching characteristics of the sinter. The blending of low-cost, high-alumina materials with aluminum silicate materials to give an alumina-to-silica mole ratio of 0.90 or greater would improve alumina and soda extraction and minimize operating problems in the lime-soda sinter process.

Jan 1, 1970

By W. S. Sanner

A High Splint coal was carbonized in a low-temperature, fluidized-bed sys-tem to study the effects of thermal cracking on the products of decomposition. The coal was fluidized in recycle gas at 485° to 600° C, and the products were cracked at 600°, 700°, and 800° C in a bed of fluidized coke. Yields of tar, pitch, paraffins, and olefins decreased as carbonization temperature increased. Thermal cracking of the tar vapors produced the highest tar yields at 600° C, and light oil yield increased at cracking temperatures up to 700° C. At an 800° C cracking temperature, the yield of light oil decreased.

Jan 1, 1969

By C. E. Jordan

The Bureau of Mines conducted tests on seven samples of Florida phosphate operations.slimes to develop a method to recover phosphate presently being discarded because of its small grain size. A system of hydrocyclones and hydroseparators was used to recover up to 96 pct of the plus 400-mesh material from the slimes. This plus 400-mesh material was subjected to fatty acid flotation, and concentrates containing up to 33.4 pct P205 were produced. As much as 88 pct of the phosphate (P205) was recovered from the plus 400-mesh material, and up to 29.6 pct was recovered from the total slimes.

Jan 1, 1982

By W. H. Ode, W. A. Selvig

Investigations have shown interesting relationships between primary-tar and light-oil yields and chemical analyses of coals. These studies have been based largely upon results published by the Bureau of Mines in connection with its survey of the gas-, coke-, and byproduct-making properties of American coals. This paper gives the results of a similar correlation in which the range in rank and type has been extended to include nearly all classes of coal, the object being to determine relationships that are significant in predicting tar and light-oil yields from chemical analyses of coals. The yields of primary tar and light oil are important in two fields of coal utilization, namely, combustion and carbonization. It is generally recognized that the principal cause of smoke produced upon burning coal is incomplete combustion of tar and light-oil vapor released during burning. The greater the tar and light-oil yields of a coal, the greater is its potential smoke-producing property. During the present war, development of new sources of fuel oil has been emphasized, especially where the supply of petroleum products is limited. One possible source of a substitute fuel is the tar and light oil that can be obtained by low-temperature carbonization of coal. In both England and Germany large quantities of low-temperature tar and oil are being processed as a source of liquid fuels. It is obvious that primary-tar and light-oil yields are of paramount importance in the selection of coals for such use.

Mar 1, 1944

By Julie Mitchell, Robert King, Len Eros

The Bureau of Mines has studied the Deserado Mine computerized monitoring and control system, located in Rangely, Colorado, to acquire knowledge about the overall costs and benefits of mine monitoring systems. The Deserado system is a complex system monitoring environmental parameters, electrical power, and operation of all mine equipment, and controlling the entire conveyor haul age system. This paper discusses the evaluation of the Deserado monitoring system from initial design through system installation and operation. It also examines the costs, benefits, and performance of the monitoring system.

Lower the respirable dust exposure of longwall shearer operators by use of a modified head to tail cutting sequence. Approach Modify the cutting sequence of double-drum shearer operations cutting unidirectionally head to tail, so that the tailgate drum is used to mine the entire coal face except when cutting out at the head. This approach would place the primary dust generating source, the cutting action of the drum, on the return air side of both shearer operators. How It Works Currently, 75% of the double-drum shearers in operation employ a unidirectional cutting sequence. On half of these operations, the primary cut is taken as the shearer travels from the headgate to tailgate ends of the face, with roof support to be advanced on the intake air side of the shearer. Typically, the leading (tailgate) drum is taking a full cut during the head to tail pass and the trailing (headgate) drum is cutting bottom coal. In this mode of operation, the dust generated by the trailing (headgate) drum can spread out into the walkway, and increase the respirable dust exposure of both head and taildrum operators. As an alternative, if the trailing drum is "free wheeling" or cutting minimal coal during the head to tail cut, and bottom coal taken by the tailgate drum during the tail to head clean-up pass, both operators are able to work on the intake air side of the primary dust generating source (drum) except when cutting out at the head. This modified cutting sequence would save wear on the conveyor and help to eliminate overloads, as well as reduce the respirable dust exposure of both shearer operators. This modifcation is only applicable to long-wail operations currently cutting unidirectional head to tail, and to those operations where this unidirectional cut would not produce operating constraints.

Jan 1, 1981

By Maria I. De Rosa

Table 10 and figure 4 show the number of fires and fire injuries occurring at the surface of underground metal/nonmetal and stone mines by state during 1990-2001. Table 10 also shows the injury risk rates, employees' working hours, and lost workdays. A total of 12 fires occurred in 11 states; 5 of the fires caused 5 injuries. The yearly average was one fire and 0.42 injury. Five fires with two injuries occurred at metal mines, five fires with two injuries occurred at nonmetal mines, and two fires with one injury occurred at stone mines. None of the fires involved contractors. The Ewhr value was 58 x 106 hr (Irr = 0.017), and the LWD value was 75. Nevada had the most fires (two fires and no injuries). Ohio, New Mexico, Missouri, South Dakota, and Idaho each had one fire with one injury. Of these states, Missouri had the highest injury risk rate value (In = 0.25). Table 11, partly illustrated in figure 5, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires decreased during most of the six time periods. The number of fire injuries and employees' working hours decreased during all of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 12-17 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 6 shows the major variables related to fires for 1990-2001. Table 18 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By C. Travis Anderson

 The general conclusion of earlier investigators was that the action of sulfur dioxide on manganese oxides of Cuyuna ores was not sufficiently pre- ferential to be attractive as the basis for a commercial process. Bradley4/ and his coworkers discarded it for leaching with boiling ammonium sulfate solution, and Sweet5/ used a baking operation to render the iron insoluble. These results were confirmed by the early tests in the present investigation, which were made on brown ores (Sagamore), using acid additions, because at that time the Technologic Committee on Manganese held the opinion that these ores constituted the major available reserve in the Cuyuna district. However, when it appeared that the black ores, or the formation in which they occur, were a possible source of a large tonnage of manganese, the use of sulfur dioxide and sulfuric acid leaching was again reviewed, and a satis- factorily preferential action on the manganese was found. It was originally thought that the use of sulfuric acid ahead of, or at least with, the sulfur dioxide simplified the process, particularly by preventing formation of dithionates. Removal of the phosphorus from the solution by neutralization with lime or fresh ore was suggested. The tests recorded in this report indicate that it is not practicable to use enough acid to prevent formation of dithionate and that the value of excess sulfuric acid is doubtful, particularly in regard to satisfactory manganese:phosphorus and manganese:iron ratios.

Jul 1, 1942

By J. A. Zimrner, R. J. Tirnko

The roles of main mine fans in underground mines are to induce airflow and continuously re- move hazardous gases and dust. While most larger mines use multiple fans to accomplish these tasks, many smaller mines employ only a single fan. This paper concentrates on those mines having only one fan to provide ventilation needs. If this fan should cease to function, it is likely that methane concentrations will in- crease in some areas of the mine. As a safety precaution, Federal Regulations require that personnel must be- gin evacuating the mine within fifteen minutes after fan stoppage. Powered haulage can be used to transport workers to the mine portal as long as travel is through areas where hazardous levels of methane are not expected. To determine where methane will accumulate along haulageways during a fan stoppage, air samples must be taken at specific areas and analyzed for hazardous gases. During this study, procedures were developed for measuring methane levels along the haulegeways that are used to exit a mine following stoppage of the main mine fan. Methane levels were measured in four different mines at selected underground locations during four planned fan stoppages. In these mines the measurements taken only at the specified locations showed that, if workers had used electrically powered haulage to exit the mine following a fan stoppage, the methane accumulated along haulageways during fan stoppages would not have significantly increased the risk of an ignition.