Search Documents

By K. Woodward, Y. Potvin, B. McFadyen, M. Grenon

Open stoping has become a popular mining method in hard rock mines, not only due to the safety of the method as a non-entry approach, but also because of the high extraction rate and low costs. At mine sites, stope performance is evaluated by calculating stope overbreak using the stability chart. However, limitations of the stability chart regarding the precision of the predictions, nonconsideration of factors such as the influence of blasting, and the exclusion of underbreak have led to non-optimal designs. The capabilities of today's computers have increased the amount of data being collected and the power of models being built. This article presents a step towards a new stope design approach where stope overbreak and underbreak are measured and georeferenced using octrees at an approximately cubic metre resolution and predicted using multivariate statistical models (partial least square, linear discriminant analysis, and random forest). Results show that overbreak and underbreak location along the design surface and their magnitude are predicted with good precision using a random forest model. These predictions are used to build the expected geometry of the open stope. The resolution of the data and the use of multivariate analysis has enabled the prediction of variation in stope performance along the design surface, going well beyond the simple qualitative per stope face prediction provided by a traditional stability chart approach.

Jun 5, 2023

By Y. Jeong, K. Kim

Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of ‘what if’ studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.

Dec 13, 2023

Mr R.D. Beck attended Felsted School in Essex (England) and the Royal School of Mines, University of London, where he ob¬tained the degree of B.Sc.(Eng.), A.R.S.M. in mineral technology in 1969. His other qualifications include Pr.Eng. (1976), C.Eng (1975), and M.I.M.M. (1975). He joined Gold Fields of South Africa in December 1969, and worked at Doornfontein Gold Mine, Greenside Colliery, West Driefontein Gold Mine, Zwartkloof Fluorspar, Gold Fields Laboratories, Gold Fields Head Office, Libanon Gold Mine, and Kloof Gold Mine before being appointed Plant Superintendent at East Driefontein Gold Mine in January 1973. In June 1976, he was transferred to Head Office as Group Metallurgist, followed, in November 1978, by his secondment to Black Mountain Mineral Development Company as Plant Superintendent, to take on-site responsibilities for staff training, plant commissioning, and start up. On his return to Head Office in July 1980 as Assistant Consulting Metallurgist, he was responsible for Black Mountain and new metallurgical projects. Then, in January 1984, he was appointed General Manager of the Zinc Corporation of South Africa Limited. He became a member of The South African Institute of Mining and Metallurgy in 1973.

Jan 1, 1985

The October General Meeting of the Institute was held in Kelvin House, Johannesburg, on 15th October, 1969, at 4.30 p.m. Mr J. K. E. Douglas (President) was in the Chair. There were also present 17 Members, Messrs: M. Barcza, R. C. J. Goode, J. A. Nixon and V. C. Robinson (Council Members), M. L. Fitzgerald, D. F. H. Graves, C. G. Hinds, S. D. Hill, J. S. Hall, D. F. Malan, T. Meyer, W. pyne-Mercier, K. S. Rae, S. G. Taussig, L. W. P. van den Bosch, Dr A. Whillier, C. H. Wyndham. Four Associate Members: Messrs O. Davel, M. J. Martinson, M. P. J. Sandys, T. G. Harington. One Student: R. P. W. Henrard. Three Visitors: Messrs A. V. Pike, B. Schmitz, A. P. Raats. Secretaries: D. C. Visser and S. de. Gersigny. Total present: Twenty-eight. OBITUARY The President: "It is my said duty to announce the death of Pieter Ulrich Fischer, Member, who joined the Institute in 1961 and passed away on 24th June, 1969. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments' silence." MINUTES The President: "The minutes of the last meeting will only appear in next month's Journal and I would request that the confirmation of these minutes be held over." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades:" Members: Alexander Edward O'Meara, Anton Leopold Melvill, WilIiam Harold Wise, Eric John Dunstan, Frank Nel, Lubertus Hendrikus Jakob Poortier. Associate Members: Michael Irvine Britten, Selwyn Wilson Lange. James McCormack, Christiaan Lodewyk de Jongh, WilIiam Andrew Hustrulid, Reinhold Johannes Ortlepp, Felix Henry Lancaster. Graduates: Willem Adriaan Gericke, Hamish David Sneddon Miller, David lan Ossin, Robert Antony Layboume, Ewart John Shillaber, Colin Hewitt Wiggett. Affiliates: Bernard Andre Thomas, Waiter Arthur Wood, Andrew John George Paschalides, David John Perry, Alex Richardson, Gert Blekker Kotze. Student: Matthys Jacobus de Beer. MEMBERS TRANSFERRED TO A HIGHER GRADE From Associate Member to Member: David Alphonso Viljoen. From Student to Associate Member: Michael Charles Carruthers. "I welcome the newly elected members to the Institute and congratulate the members who have been transferred to a higher grade." PAPERS FOR PRESENTATION The President: "Professor Wyndham, may I call on you to deliver the paper entitled 'Factors affecting the mechanical efficiency of men shovelling rock in stopes', written jointly with J. F. Morrison, J. H. Viljoen, N. B. Strydom and A. Heyns." After the presentation of the paper the President said: "Gentlemen, I would like to thank Dr Wyndham and his colleagues for once again reporting through the medium of this Institute the results of the very important work they are carrying out at the Human Science Laboratories. It is most appropriate that this work which is leading to a better understanding of the capabilities and efficiency of the human body under the arduous conditions encountered underground should be reported to this forum. In this way our members, who are actively engaged in the job of mining, can firstly learn something of this research and secondly, can, with their practical knowledge of conditions underground, contribute to what has been learnt and possibly pose new problems for our scientists in the laboratories. The scientist should always have the opportunity of subjecting his research to the scrutiny of people engaged in practical operations. By the very nature of our gold mines we are unfortunately heavily dependent on a large labour force and while mechanization has been introduced wherever feasible, we are likely to continue to be heavily dependent on this labour. In accepting this fact we can be proud in this country of what has been achieved, not only in obtaining the best efficiency from labour but in ensuring that their working conditions are reasonable and that their health and well-being are adequately cared for. When one visits our gold mines, one cannot help being impressed with what is being done to ensure that we have a satisfied, happy and healthy labour force. The Human Sciences Laboratory with its scientific approach has assisted greatly in promoting a better understanding of the problems associated with labour under the conditions experienced on our mines. Thank you." Mr M. Martinson then contributed to the discussion. (This contribution will appear in a later issue of the Journal.) "Professor Wyndham, may I call on you to deliver the paper entitled 'Acclimatizing men to heat in climatic rooms on mines,' written jointly with Prof Strydom." After Dr Wyndham had presented the paper the President said: "Thank you Dr Wyndham for so ably describing the work associated with the acclimatization procedures on our gold mines. It has certainly been an eye-opener to those of us not familiar with this work and I believe it is very important that everyone and not only people in the gold mines should know about it. It is fortunate that all industries do not have the same arduous heat conditions experienced on our mines but other industries such as our chemical and metallurgical industries do have other problems relating to the adjustment of labour to the work situation. The scientific approach employed by the gold mines in tackling this problem is an example to these industries of what can be achieved by logical

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By A. Tosun

"The size distribution of the muckpile formed as a result of open pit blasting operations has a considerable effect on the efficiency of loading, hauling, and crushing. Various researchers have developed specialized computer software that uses image analysis methods for determining the size distribution of the muckpile. However, these methods have some limitations. One of the most important of these limitations is that the very fine fragments in the muckpile cannot be used in the size distribution calculation. In this study, 18 test blasts in total were carried out in two limestone quarries belonging to Batiçim Corp. in Izmir, Turkey. A new model was developed in order to ensure that very fine fragments are used in the size distribution calculation. The size distributions of the test blasts were calculated by both the Wipfrag computer program and the new model. Correlations were established between the muckpile size distributions determined by both methods and the parameters determining the efficiency of the loader. IntroductionThe size distribution of the muckpile formed as a result of open pit blasting operations has a considerable effect on the efficiency of loading, hauling, and crushing. Various researchers have established certain correlations for predicting the efficiency of the operations according to the muckpile size distribution so that production can be carried out economically (Tunstall and Bearman, 1997; Nielsen and Kristiansen, 1996; Workman and Eloranta, 2004; Michaud and Blanchet, 1996; Frimpong, Kabongo, and Davies, 1996; Osanloo and Hekmat, 2005; Molotilov et al., 2010). In these studies, the 50% passing size (X50) is generally used. These methods rely on the correct measurement of the size distribution of the muckpile formed by the blast. The most reliable measurement method would be to subject the entire muckpile to a sieve analysis, but this is obviously impracticable. Therefore, computational method based on image analysis have been developed. These include IPACS (Dahlhielm, 1996), Tucips (Havermann and Vogt, 1996), Fragscan (Schleifer and Tessier, 1996), Cias (Downs and Kettunen, 1996), GoldSize (Kleine annd Cameron, 1996), Wipfrag (Maerz, Palangio, and Franklin, 1996), Split Desktop (Kemeny, 1994), PowerSieve (Chung and Noy, 1996), and Fragalyst (Raina et al., 2002). In these methods, the size limits of the fragments forming the material are determined by image analysis on photographs of the muckpile. However, the computer software has some limitations. It does not take into account the third dimension of the muckpile, nor the size distribution of very fine fragments. In particular, the fragment size ranges below 2.5 to 3 cm cannot be determined, and therefore these cannot be included in the muckpile size distribution. However, the muckpile formed by a bench blast contains a wide range of particle sizes (Tosun et al., 2015)."

Oct 1, 2018

By P. Cowx, L. Els, P. Smith, R. Nordhagen

"Tapping operations at ferroalloy smelters generate a significant amount of fume. Effective capture of fumes is required to meet the obligations of environmental, as well as occupational, legislation.A study was completed on an existing fume extraction system at a ferromanganese furnace tapping area. The area under consideration included the tap-hole, launder, and ladle area. The study consisted of site test work as well as computational fluid dynamics (CFD) modelling to identify and evaluate solutions.Site test work and observations during furnace operation provided a baseline of system performance as well as input parameters for CFD modelling. Gas flow rates and energy contents from each extraction area were measured. Photographs and video footage were taken to evaluate areas of fume leakage.The CFD study was firstly validated against site observations to ensure the accuracy of input parameters. Thereafter several modification concepts were modelled and suitable combinations were investigated to ensure robust solutions. The following concepts were considered:•,Air curtains•,Ladle hood aspect ratio and position•,Increase of ladle extraction volume•,Extension of the length of the tapping garage structureThe paper presents the results of a performance test on a working ferromanganese tapping area fume extraction system and the results of CFD modelling as compared to site test results. Upgrade options are evaluated and an integrated robust upgrade of the system described."

Jan 1, 2014

By H. E. James

During the past ten years there has been an upsurge of interest in the development of selective ion exchange resins and solvents, and of ion-exchange and solvent extraction equipment tailored to the special requirements of mineral-processing circuits. It is therefore not surprising that the recent Symposium on Ion Exchange and Solvent Extraction in Mineral Processing, held at the National Institute for Metallurgy (NIM) on 7th and 8th February, 1980, was a resounding success. This Symposium, organized jointly by NIM. Ion exchange and solvent extraction The Symposium on Ion Exchange and Solvent Extraction in Mineral Processing, which was organized jointly by the National Institute for Metallurgy, the South African Institution of Chemical Engineers, and the South African Institute of Mining and Metallurgy, was held in Randburg on 7th and 8th February, 1980. Analytical chemistry The Fifth International Conference on Analytical Chemistry, organized by the Chemical Society, is to be held at Lancaster University, England, from 20th to 26th July, 1980. Coal mining The First International Symposium on Thick and Steep Seam Coal Mining will be held in London from 18th to 21st May, 1980. Mineral processing The XIV International Mineral Processing Congress will be held in Toronto from 10th to 16th October, 1982. The theme of the congress will be 'Worldwide industrial application of mineral processing technology'. Sessions will be held on the following:

Jan 1, 1980

By J. S. Contreras, E. Córdova, I. Gottreux, A. Anani, A. Ferrada

Cave mining is an underground mass mining technique. The largest projects, which are known as ‘super caves’, produce hundreds of thousands of tons of ore per day, which involves large footprints with considerable column height, and have a life of mine of over 20-40 years. These operations are typically located deep, under high stresses and in competent rock masses, making initiation and propagation of the caving process harder to manage. These challenges must be confronted by optimizing the fragmentation of the orebody to achieve smaller size blocks that will result in consistent caving and improved flow of the ore from the drawpoints. To achieve better performance from the drawpoints, preconditioning is applied to fragment and damage the material required to cave. We present a proposed design for preconditioning in underground mines, considering the challenges that these large-scale mines are already facing, based on a comprehensive analysis of current design parameters, case studies, and sensitivity analyses using numerical models.

Feb 2, 2021

By M. C. Bekker, T. Govindasamy

The potential benefits of implementing the Last Planner System (LPS) on mining infrastructure projects were explored through two case studies in the South African mining industry. The first part of the study involved measurement of the impact of LPS through earned value techniques on secondary project data. The second part sought to establish the lean construction success factors leading to improvements in construction performance. This was done by means of a research questionnaire distributed to the project owner’s teams, contracted parties, and the LPS facilitators. The results revealed a positive correlation between LPS application and planned percentage complete. However, the performance achieved during the LPS pilot was not sustained. The success factors and benefits considered most evident in the case study pilot differed among the three stakeholder groups. The findings are expected to guide construction stakeholders to better define performance measures and focus on factors required to make LPS implementation more effective in the South African mining sector.

Feb 12, 2024

By C. Hartford, T. Holmes

Bulk-solids handling systems are often the most over-looked component and thereby weakest links in a processing plant’s value chain. Since their performance can dictate that of the entire operation, they actually deserve special attention. When designing a liquid handling plant, density and viscosity are well known and commonly used as design parameters. Bulk solids however, differ. While the design process is similar, the relevant parameters in handling bulk solids are instead friction, cohesive strength, compressibility, and permeability. These then vary depending on the mineralogy, particle size distribution and shape, moisture content, storage time-at-rest, temperature, and consolidation pressure. With so many variables, it becomes important to characterize each individual bulk solid across the full range of representative process conditions within the handling system, plant wide – or if you are not very lucky, suffer the consequences of poor material flow. Measuring flow properties and applying them correctly in bulk solid handling system design reduces project risk, saves significant capital, and drastically increases throughput, especially when done in the early stages of a project. Keywords: Flow Properties, Bulk Solids, Process Conditions, System Design

Jan 1, 2020

By K. B. Le Bron, T. van Aard

The empirical pillar strength formulae have been widely, and in most cases successfully, applied to design underground pillars for mines in the Bushveld Igneous Complex (BIC). This paper presents the case for combining the empirical method with numerical modelling when it comes to crush pillar stability analyses. The benefits include an understanding of potential failure mechanisms, which may then be accounted for in the designs. In addition, the impact of weak layers, such as shear zones, the impact of the dip of the orebody, differences in layouts, such as holing widths and the presence of advanced strike gulleys (ASGs) immediately adjacent to the crush pillars, and stress regime (k-ratio) may be studied using numerical modelling, as it is not accounted for in the empirical method.

Mar 5, 2025

1. USSR co-operation International Mining, the London-based publication, has received USSR Government approval to publish a Russian language edition for circulation in the Soviet Union. 2. Mintek publications Special Publication no. 11. World chromite resources and ferochromium production, by M.H. Silk. 1988. 160 pp. South Africa RlOO including postage; elsewhere US$lOO including postage. Application Report 4 The development and implementation of novel refining processes for the platinum-group metals (including the refining of anode slimes). 1988. 16 pp. Report M249D The acid activation of local clays including solid-liquid separation, by P.M. Cole and G.F. Lahoud. First issued Mar. 1986, reissued Apr. 1988. 46 pp. ReportM250D The production of refined feromanganese in a transfered- arc plasma furnace, by A.F .S. Schoukens and M.Ford. First issued Mar. 1986; reissued Apr. 1988.23 pp. ReportM257D Extraction of gold from eastern Transvaal concentrates by roasting and cyanidation, by J.J. Robinson. First issued Apr. 1986; reissued Apr. 1988. 55 pp. ReportM267D The recovery of gold from backfil by gravity separation, by R.N. Guest. First issued Jun. 1986; reissued Apr. 1988. 18 pp. ReportM285D Autogenous miling of kimberlite, by D.I. Hoyer. First issued act. 1986; reissued Apr. 1988. 11 pp

Jan 1, 1988

By C. Gatschlhofer, A. Krammer, H. Raupenstrauch, T. Hochsteiner, A. Holzer, L. Wiszniewski

The rising demand for lithium-ion batteries, coupled with international climate targets, emphasises the need for circular economy and zero-waste recycling approaches. However, so far, no industrial-scaled solutions are available that fulfil global recovery targets. Therefore, a novel pyrometallurgical reactor was developed at the Chair of Thermal Processing Technology at Montanuniversitaet Leoben to avoid lithium slagging and recover volatile elements via the gas phase. Nevertheless, previous results show that several impact factors, including interfering elements or pre-treatment steps, strongly limit the recycling efficiency of black mass. To simulate the black mass and provide feedback on possible influences of pre-treatment steps, cathode material from production with additives of interfering elements was analysed regarding melting behaviour. The results show that formation of a further processable alloy was increased by almost 50% when pretreatment steps were excluded, indicating pre-treatment steps as a major influence to be considered within this specific recycling route.

Jan 1, 2023

By W. R. Matizamhuka

"The consolidation of nano-sized composite materials presents a challenge using conventional hot pressing methods. Spark plasma sintering (SPS) technology has shown great promise in the successful sintering of nanoreinforced composite materials. This qualitative review seeks to impart knowledge gathered, and progress made over the years on the consolidation of nanocomposite materials using SPS technology. The review is aimed at introducing this technology to the South African science and engineering community. Emphasis is on improving the mechanical properties of structural ceramic nanocomposite materials, which over the years have shown great promise in a wide range of applications, including transport, energy, mining, and the environment. Although success has been achieved within the laboratory for research purposes, there are still great opportunities to commercialize the technology for the production of larger components with more complex shapes.IntroductionSince the pioneering work of Niihara and Nakahira (1991) over a decade ago there have been extensive attempts to harness the potential of nanostructural metals, ceramics, and composites in a number of applications (Niihara and Nakahira, 1991; Selaho et al., 1997; Sekino and Niihara, 1995; Khalil, 2012; Aalund, 2008). It is generally realized that reducing the grain size of materials to nanoscale offers a significant improvement in properties. Attempts to synthesize nanostructured compacts by conventional sintering methods have not succeeded owing to the uncontrollable high rates of grain growth driven by long dwelling times at the sintering temperatures and large powder surface areas (Sergueeva et al., 2009; Gua, Khora, and Chieng, 2004; Tang et al., 2009). Following the development of spark plasma sintering (SPS) technology, it is now possible to process nanocrystalline materials with controlled grain growth. SPS, also referred to as the field-assisted sintering technique (FAST) or pulsed electric current sintering (PECS), was developed with the aim of improving on the well-established hot pressing (HP) technology (Kessel and Hennicke, 2007;"

Jan 1, 2016

By Paul B. Crawford, Gerald N. Pitts

"A new method is introduced for the simulation by computer of the flow of liquid underground. The method has application in simulating, for example, liquid withdrawal systems, injection systems or injection-well systems. The computer simulation of liquid flow permits the utilization of the known properties of the rock in developing a model of the permeable rock mass.The flow properties of the rock at a specific site arc generated statistically using a random number generator. After defining in this manner the rock properties of each element in the computer grid, the streamlines or flow paths of the liquid are traced using the new method. The simulation is designed especially for computers. The meandering character of the liquids paths is displayed clearly as the fluid moves underground, thus providing the technical information required for the control of the movement of liquid."

Jan 1, 2014

By P. M. Mashaba, S. O. Bada

An advanced high internal phase water-in-oil (HIP W/O) emulsion binder and flotation with an internal dispersed water phase of 95 vol% was used to beneficiate South African weathered coal from discard dumps. Five coal samples with calorific values ranged from 8.48 MJ/kg to 20.94 MJ/kg were utilized. The performance of the HIP W/O emulsion was compared to that of kerosene in terms of the physicochemical properties of the clean coal products. A 5 kg/t emulsion binder addition produced a high-quality coal concentrate with 11.76% ash and a heating value of 28.61 MJ/kg from a sample containing 29.34% ash. Using the same dose and coal sample, kerosene resulted in a clean coal concentrate with 17.47% ash and a calorific value of 26.42 MJ/kg. Further samples were also beneficiated using 5 kg/t of W/O emulsion. The highest increase in calorific value was achieved from the beneficiation of a sample containing 48.71% ash, from 8.48 MJ/kg to 18.16 MJ/kg. It has been established that emulsion binders can upgrade coal samples dumped many decades ago.

Aug 2, 2022

1. Book reviews Mill Operators' Conference. Parkville (Australia), Australasian Institute of Mining and Metallurgy, 1982. 425 pp. Reviewer: B. K. Loveday Off highway truck haulage. Newman Combined Group, the Australian Institute of Mining and Metallurgy and the Institute of Engineers in Australia. Sep. 1982. Reviewer: B. J. Vorster Environmental engineering in South African mines.Johannesburg, Mine Ventilation Society of South Africa, 1982. 974 pp. Reviewer: A. N. Brown Underground Operators Conference. West Coast Tasmania Branch. Australasian Institute of Mining and Metallurgy. Reviewer: D. R. Aspeling 2. New publications Electric steelimaking in the eighties: challenges and opportunities. Rotterdam, Balkema, 1982. 362 pp. $50.00 or £33. Tungsten: a review, by P. M. Harris and D. S. C. Humphreys. London, Institution of Mining and Metallurgy (Occasional Paper 2), 1983. Members: £3, nonmembers £6. The platinum industry - prospects in recovery. London, Shearson{American Express Ltd (St. Alphage House, Fore Street, London EC2Y 5DA), 1983. £75. The best of E&MJ mining and processing idea book' New York, Engineering and Mining Journal, 1983. 128 pp. Free with subscription to Engineering and Mining Journal. Mining 1983. Harlow (U.K.), Longman Group Limited, 1983. 500 pp. £39.50. Ooncise guide to world coalfields. London, World Coal Resources and Reserves Data Bank Service (14/15 Lower Grosvenor Place, London SW1W OEX), 1983. 380 pp. £45. 3. Canadian publications Asbestos, by G. O. Vagt, 9 pp. Ooal and Coke, by J. A. Aylsworth, 16 pp. Orude oil and natural gas, by R. L. Thomas, 12 pp. Phosphate, by G. S. Barry, 8 pp. Rhenium, by S. A. Hamilton, 3 pp. 4. Mintek reports Report 2102D The recovery of magnesite from dump fines from the Strathmore Mine. (First issued Feb. 1981.) Report 2106D The evaluation of drill cores and a bulk sample from a deposit of andalusite near Thabazimbi. (First issued Mar., 1981.) Report 2108D Evaluation of a grinding aid in batch grinding, classification, and gravity concentration. (First issued Jul. 1981.) Report 2109D The evaluation of an andalusite deposit from Kleinfontein, Groot Marico. (First issued Apr. 1981.) Report M7D The beneficiation of chromite ore from the Ma-l seam near Marikana. (First issued Nov. 1981.) Report M62 A preliminary investigation into the extraction of zinc by direct oxidative leaching of high-manganese sphalerite. Report M76 A mineralogical investigation of a refractory gold ore, and of a sulphide concentrate and calcined tailing from that ore. Report M85 List of unrestricted Mintek publications issued from 1966 to 1982. Report M97 Reduction in metal consumption by the use of alternating lines of higher and lower lifter bars in a rod mill. Report M98 Multivariable control and optimization of the operation of a milling circuit at East Driefontein Gold Mine. Report M101 The potentiality of heat-treated balls in the grinding of gold ores. X-ray diffraction The Southern Transvaal Section of the South Mrican Chemical Institute is to present a mini-course on 'X-ray Diffraction: Theory and Application' in Johannesburg on 18th and 19th October, 1983.

Jan 1, 1983

By S. Kauchali

"Underground coal gasification (UCG) is recognized as an efficient mining technique capable of chemically converting the coal from deep coal seams into synthesis gas. Depending on the main constituents of the synthesis gas, chemicals, electricity, or heat can be produced at the surface. This paper provides a high-level graphical method to assist practitioners in developing preliminary gasification processes and experimental programmes prior to detailed designs or field trials. The graphical method identifies theoretical limits of operation for sensible gasification within a thermally balanced region, based primarily on the basic coal chemistry. The analyses of the theoretical outputs are compared to actual field trials from sites in the USA and Australia, with very favourable results. A South African coal is studied to determine the possible synthesis gas outputs achievable using various UCG techniques: controlled retractable injection point (CRIP) and linked vertical wells (LVW). For CRIP techniques, an important result suggests that pyrolysis, and subsequent char production, are important intermediate phenomena allowing for increased thermal efficiencies of UCG. The conclusion is that South African coals need to be studied for pyrolysis-char behaviour as part of any future UCG programme. The results also suggest that UCG with CRIP would be a preferred technology choice for Bosjesspruit coal where pyrolysis dynamics are important. Lastly, the use of CO2 as oxidant in the gasification process is shown to produce syngas with significant higher heating value. Introduction and literature surveyCoal is a commonly utilized fossil fuel, providing over 40% of global electricity demand and about 90% of South Africa’s primary energy needs. However, less than 20% of the known world resources are suitable for possible extraction using conventional surface and underground mining techniques (Andrianopolous,, Korre, and Durucan, 2015). Underground coal gasification (UCG) has the potential to recover the energy stored in coal in an environmentally responsible manner by exploiting seams that are deemed unmineable by traditional methods. The UCG process, if successfully developed, can increase coal reserves substantially. For example, in the Limpopo region of South Africa alone, the estimated potential for UCG gas, based on existing geological records, is over 400 trillion cubic feet (TCF) natural gas equivalent – this is about a hundred times more gas than the existing 4-TCF Pande-Temane natural gas field reserve in Mozambique (de Pontes, Mocumbi, and Sangweni, 2014)."

Oct 1, 2018

By J. Petersen, A. E. Lewis, J. Chivavava

Rare earth elements (REEs) have special properties that prompted their extensive use in high-tech applications. The demand for REE has, therefore, increased over the past years, resulting in the supply risk of the materials. Extraction from non-conventional low-grade ores, like easy-to-mine ion adsorption clays (IACs), by hydrometallurgical methods is being explored to supplement the supply of REEs. The extraction of REEs from low tenor IAC leach solutions requires enrichment using cost-effective methods such as precipitation. Therefore, the aim of this study was to understand the recovery of REEs from IAC leach solutions using various reagents for precipitation. In the first part of the study, recoveries of REEs from IAC leach solutions through direct precipitation using H2C2O4 and NH4HCO3, as well as antisolvent crystallization using C2H5OH, were predicted via thermodynamic modelling using OLI Stream Analyzer. Verification experiments were then conducted through the use of an agitated reactor. Simulation results showed that high yields of REEs were possible using each of the reagents, but large quantities of C2H5OH were required. Experimental results confirmed the high yields predicted from simulations. Precipitation with H2C2O4 was found to selectively recover REEs while rejecting Al. However, utilization of NH4HCO3 and C2H5OH resulted in the co-precipitation of Al. Furthermore, the yield of Y from antisolvent crystallization was significantly lower than the theoretical value. The product recovered from antisolvent crystallization consisted of well faceted, large crystalline particles, which filtered faster than the fine, amorphous REE carbonates recovered using NH4HCO3. REE oxalates were crystalline, larger than the REE carbonates and, overall, showed the highest filtration rate.

Dec 11, 2024