Search Documents

By A. S. Geldenhuys, L. S. Leal Filho, D. A. Deglon, T. C. Souza Pinto

The Brucutu iron ore mine (Minas Gerais, Brazil), is Vale`s largest iron producing operation achieving around 21 million tons by flotation of iron ore pellet feed per annum. The run of mine is mainly composed of hematite (70%) and quartz (30%). After preparation (comminution and sizing), the slurry is submitted to reverse cationic flotation of quartz under basic conditions (pH=10.5). Corn starch (500g/t) is used to depress Fe-bearing minerals and alkyl (C10) ether amine is the collector for quartz. The flotation circuit is arranged in a “coarse” section utilizing dated 28m3 square Wemco cells, and a “fine” section utilizing modern 160m3 tank cells. The “coarse” flotation circuit treats material from the deslime cyclone underflow while the “fine” circuit treats material from the deslime cyclone overflow and the pulp product from the “coarse” circuit scavenger 2 bank. Evaluation of process performance is of high importance as even small gains can lead to large improvements for this high throughput plant. Cell-by-cell samples of the froth products, selected feed and pulp-products were analyzed for flow-rate, overall chemical composition, and particle size distribution. Bank-by-bank samples of the feed, froth and pulp products were analyzed on an assay-by-size basis. In addition, the flotation cells were hydrodynamically characterized and gas dispersion parameters assessed. The detailed experimental program resulted in a thorough characterization of the process and enough information to produce a calibrated floatability component model. Longer mainline residence time results in significant Fe2O3 losses while yielding little benefit in terms of SiO2 grade. Scavenger 2 has twice the residence time of scavenger 1 while having to treat only 10% of the SiO2; resulting in high Fe2O3 recoveries to the froth and poor separation. In addition, it is shown that the Fe2O3 exhibits true flotation behavior resulting in increased Fe2O3 losses. The detailed data collection campaign coupled with in depth data analysis and modelling gives unprecedented information and highlights avenues for optimization that was previously unknown. Keywords: Froth Flotation, Process modelling, Process evaluation, Metallurgical survey

Jan 1, 2020

By D. van der Westhuizen, H. Krieg, M. Kruger

In the field of Fischer-Tropsch synthesis catalysts, cobalt, platinum, and aluminium are the primary metal constituents of the conventionally used cobalt catalyst. While platinum recovery remains a focal point in this field, a recent endeavour by a South African company emerged, which aimed to recover cobalt and aluminium from spent Fischer-Tropsch synthesis catalysts for potential use in the agricultural sector. This study aimed to optimally separate cobalt and aluminium from spent Fischer-Tropsch synthesis catalyst for this purpose. It further leverages the OLI database to predict metal speciation during solvent extraction to aid with experimental planning. Shake-out tests were conducted to determine optimal separation. conditions, which were validated using three distinct methods: (i) evaluating the experimental error, (ii) comparing results with similar research, and (iii) validating results against the OLI database. The investigation revealed the pivotal role of the aqueous pH yielding effective separation at pH 3.13 ([H2SO4] = 2.5 × 10−4 M) when using 20 vol.% CYANEX 272 and 50 mol.% pre-neutralisation. Effective cobalt scrubbing was achieved with 50 g/L Al at pH 2.8, while successful stripping required 1 M H2SO4. Competitive interactions between complexing aluminium and cobalt species were observed when contacting with CYANEX 272 at a pH < 4. Equipment design analysis for a targeted separation efficiency of 87% dictated the necessity of two mixer stages and a settler measuring 1.5 m × 1.5 m × 6.0 m (height × width × length). This settler would ensure sufficient residence time for gravity separation at a flow rate of 10 m3/h.

May 27, 2025

1. Reviews Extraction metallurgy, by J.D. Gilchrist. 3rd ed. Oxford, Pergamon, 1989. 431 pp. £50.00 (hard cover), £14.95 (soft cover). Reviewer. Prof. M.D. Brayshaw. Reviewer. Prof. M.D. Brayshaw This third edition bears testimony to a work that contains much of value for lecturers, students, and practising metallurgists. Mineral processing in the United Kingdom, edited by P.A. Dowd. London, Institution of Mining and Metallurgy, 1988. 223 pp. £25.00. Reviewer: Prof. M.D. Brayshaw It came as both a pleasure and a challenge for a resident of South Africa (with its volume and diversity of minerals) to review a book focusing on the beneficiation of ores from the sparsely endowed mineral chests of the United Kingdom. 2. Recent issues Rock mechanics. Theory and applications with case histories, by W. Wittke. Translated from German by R. Sykes. Berlin, Springer-Verlag, 1990. 1076pp. DM248. McGregor&apos;s quick reference to the JSE. Pretoria, Juta & Co., 1990. R39,95. McGregor&apos;s economic alternatives. Pretoria, Juta & Co., 1990. 400 pp. R34,95. 3. New journals Journal of Materials Chemistry, edited by A.R. West and J. Leader, and published two-monthly by The Royal Society of Chemistry (Blackhorse Road, Letchworth, Herts SG6 IHN, OK). £195 per year, starting in 1991. New Materials World, published monthly by Lawrence Cooklin (15 Selvage Lane, Mill Hill, London NW? 3SS, OK). £180 per year. Mendeleev Communications 4. Books from The Institute of Metals The following were published recently, or are to be published soon, by The Institute of Metals, 1 Carlton House Terrace, London SWl Y SOB, OK. Illustrated case histories of marine corrosion. 1990. Modern steelmaking methods, by C. Moore and R.I. Marshall. 2nd ed. 1990. Grain boundary fractures, by S.F. Pugh. 1991. 160 pp.

Jan 1, 1991

By M. M. Ali, C. Musingwini, R. A. Phillips

The long-term open-pit mine production scheduling problem (OPMPSP) is typically solved in two broad stages. The first stage entails optimisation of the ultimate pit limit, which delimits the economical final pit and maximises the undiscounted value of the deposit. The second stage entails optimisation of the long-term open-pit mine production scheduling, which maximises the discounted value of the deposit. The long-term OPMPSP is a type of an NP-hard problem, such as the travelling salesman problem (TSP), because it is intrinsically complex to solve since it incorporates both hard and soft constraints. Therefore, metaheuristic approaches have been used to find global optimum solutions to the long-term OPMPSP. This paper presents a metaheuristic approach utilising a dual interchange algorithm (DIA) to solve the long-term OPMPSP. The DIA is a parent algorithm which supervises two subservient algorithms, namely, simulated annealing (SA) and Tabu search (TS). The DIA selects the better solution generated in each run from the two algorithms, and simultaneously penalises the algorithm that produced an inferior solution, while rewarding the one that produced a better solution. The DIA was tested on the three-dimensional Arizona Copper Deposit (KD) dataset, which is publicly available for research purposes from the online MineLib repository. It was set to generate net present values (NPVs) in five-minute intervals and the solution improved until it plateaued at about 30 minutes of runtime. The NPVs compared favourably to those obtained on the same KD dataset but obtained over 24-hour runtimes, when solved using simulated annealing and Tabu search algorithms, and the NPV generated from the work of Muñoz (2012) using the modified TopoSort as found on the MineLib repository at the time of this study. Therefore, this paper demonstrates that DIAs can be developed and used to solve the three-dimensional long-term OPMPSP.

Sep 1, 2021

By J. Mulenshi, J. Rosenkranz, P. Khavari, S. C. Chelgani

The geometallurgical concept has mainly been applied to primary ore deposits, starting from ore characterisation to the economic optimisation of the mining operation. However, as primary ore resources are becoming depleted and lower in grade, alternative sources need to be explored and a question of adaptability of the geometallurgical approach to the secondary resource repositories arises. The particle size distribution, chemical and mineralogical compositions of the Smaltjärnen historical tungsten tailings from physical separation in Yxsjöberg, Sweden were studied using drill core samples collected from different locations within the tailings repository in order to assess the amenability of the tailings to reprocessing. The tailings are dominated by the –600 to +149 μm particle size fraction. This fraction contains most of the elements of interest (W, Cu, S, Sn, Zn, Be, Bi and F) hosted by scheelite, chalcopyrite, pyrrhotite, cassiterite, danalite (both Zn and Be), bismuthinite and fluorite, respectively. The particle size distribution and mineralogical composition vary across the repository, suggesting a possible existence of geometallurgical domains, which require further assessment to evaluate metallurgical performance. Keywords: Historical tailings, tungsten, scheelite, geometallurgy, characterisation, mineralogy, reprocessing

Jan 1, 2020

By I. O. Ondicho, E. K. Mutinda, B. O. Alunda, E. Agyekum

Driven by the necessity to improve blast performance regarding fragment size distribution in limestone mines, this paper introduces the prediction and measurement of blast fragmentation distribution through the modified Kuz-Ram (MKR) and Kuznetsov-Cunningham-Ouchterlony (KCO) models. Precise prediction and measurement of rock fragmentation resulting from blasting play a critical role in hard rock ore extraction. This is due to the substantial influence of post-blast ore size distribution on the efficiency of all subsequent downstream rock handling and processing operations. Additionally, employing secondary breakage of boulders, when necessary, leads to an unjustified rise in production costs. In this paper, the MKR and KCO models were utilised to identify the most appropriate model for application in Bisil and Simba quarries situated in Kajiado County, Kenya. Split-Desktop was used for blast fragment measurement by processing digital images obtained after blasting and computing the fragment size distribution of the blasted rock. As per the investigation, the recorded percentages of boulders generated at the sites ranged from 7% to 12.3% for the Simba quarry and from 11.2% to 23.9% for the Bisil quarry, respectively. Regression, correlation, and root mean square error (RMSE) were employed as the primary performance indicators. The study concluded that KCO outperformed MKR in accurately predicting blast fragment sizes in the examined quarries.

Mar 5, 2025

By J. Arzuúa, U. Castro-Filgueira, L. R. Alejano, F. Malan

"Pillar design for underground mining is typically done using empirical formulae or numerical modelling. Practical experience and recent literature, nevertheless, illustrate the shortcomings of these design approaches. Ongoing monitoring of pillars is therefore recommended to minimize the risk associated with these designs.In a mine where a large number of pillars are cut, different pillar strengths can be expected owing to variations in rock mass strength from area to area. This problem is compounded by the fact that in mining environments the pillars are not always cut according to the prescribed dimensions. Although the original design using either empirical methods or modelling may predict stable pillars, unstable pillars will be encountered in reality. Very conservative designs with large factors of safety may circumvent this problem, but this approach is uneconomical.A possible solution to localized stability problems may be to enhance the strength of a few unstable pillars. It may even be hypothesized that reinforcing a few critical pillars may prevent ‘pillar runs’ on a much larger scale. Rockbolting, strapping of pillars, and pillar shotcreting have occasionally been used in the past as possible solutions. It appears that these have not been successful in all cases and large collapses have occurred in spite of the pillar remedial work.The authors investigated the strapping of pillars by conducting laboratory tests on cabled rock specimens. The results were qualitatively compared to actual attempts of pillar reinforcement available in the literature, as well as additional observations in an old haematite roomand- pillar mine in Spain. Based on these results, the value of steel cabling and mesh wrapped around pillars to improve stability is demonstrated. Some cases where this approach will not be successful are also discussed."

Jan 1, 2017

By T. Matlou, S. Myendeki, V. Midzi, T. Zulu, H. Mabotja, T. Mulabisana, B. S. Zulu, L. Hlatshwayo, T. Makhateng

The Council for Geoscience (CGS) performed a macroseismic investigation following the occurrence of an earthquake in the Boksburg area on 11 June 2023. The event had a magnitude of ML 4.4 and a focal mechanism that showed the event as having strike-slip motion along a northwest-southeast oriented fault. The event resulted in aftershocks, some of which occurred away from the causative fault in the east in an area without a mapped fault. However, the cluster of past events in that area suggests that there is an active fault. Due to the size of the main earthquake, a macroseismic survey was conducted to determine its impact on the community in the region. Analysis of observed data obtained from questionnaires resulted in the creation of 153 intensity data points. Their distribution showed high intensity values close to the earthquake source area. However, the investigation highlighted a number of anomalies, such as the higher than expected intensity values observed far from the event epicentre. It could be that these anomalies are caused by site conditions, for example, amplification of ground motion due to thick soil layers.

Jan 12, 2025

1. Book reviews Underwater tools, by Donald J. Hackman and Don W. Candy. Columbus (D.S.A.), Battelle Press, 1981. 152 pp. $32,95. Reviewer: B. Schmitz Uranium exploration case histories. Proceedings of Advisory Group Meeting Vienna, IAEA, 1981. Price: Austrian schillings 630. Reviewer: E. C. Kostlin Jet cutting technology, a review and bibliography, edited by Robin Brown. Published by BHRA Fluid Engineering, Cranfield, Bedford MK430AJ, England. Reviewer: D. O&apos;Beirne 2. New Books Proceedings, Twelfth Congress of the Council of Mining and Metallurgical Institutions, by H. W. Glen (editor.) Johannesburg, The South African Institute of Mining and Metallurgy, 1982. 2 vols., 1060 pp. R78,85 (air-mail RI53,85). Amborite. Johannesburg, De Beers Industrial Diamond Division (P.O. Box 916), 1982. 6 pp. Free of charge. 3. New Journal BHRA Fluid Engineering has announced its new journal World Ports and Harbour Abstracts and the associated newsletter World Ports and Harbour News, which are issued from January 1983. The Abstracts is published bi-monthly and costs £60 in the V.K. and E.E.C., and £72 elsewhere. 4. Mintek reports Report 2134D On-line analysis, by X-ray diffraction, of fluorsparcontaining slurries. (First published 30th Sep., 1981.) Report 2135D A preliminary on-line analysis, by X-ray diffraction, of pyrite-containing slurries. (First published 30th Sep., 1981.) Report M28 The measurement of flow velocity distribution in fluids. Report M34 The determination, by atomic-absorption spectrophotometryusing electrothermal atomization, of platinum,palladium, rhodium, ruthenium, and iridium. Report M45 Two computer programmes for the calculation of massand heat balances in the production of high-carbon ferromanganese. Report M50 The development of an on-line gold analyser. Report M54 Major amounts of mercury in native gold from upper Witwatersrand sediments. Report M55 A new robust method for the treatment of analytical data. Report M57 The hydrometallurgical treatment of liquors generated by the leaching of a low-grade matte. Awards for inventions For inventing devices of exceptional value to the mining industry, two mining men were presented with awards in Johannesburg on 25th November, 1982, under the Chamber of Mines&apos; Ideas and Suggestions Scheme. Mr W. W. Malan, President of the Chamber of Mines, made the presentations.

Jan 1, 1983

By F. P. Janse van Rensburg, P. J. Le Roux

"There are numerous factors that affect open stope stability and often result in falls of ground. These falls of ground can be attributed to factors such as beam failure due to a larger than normal roof area (hydraulic radius too large), adverse ground conditions, seismicity, the stress-strain environment, absence of support, and poor drill-and-blast practices. The effect of time on the stability of open stopes is sometimes underestimated and is relatively unknown, especially on Target Mine. Actual data was collected from open stopes at Target and analysed to show the effect of time on open stope stability. The benefits of this analysis will include improved understanding of time-dependent failure, which can assist in reducing dilution and the risk of sterilization of future mining blocks. IntroductionTarget Mine is situated adjacent to the town of Allanridge, some 20 km from Welkom in South Africa’s Free State Province, and is the most northerly mine in the Welkom Goldfields area (Figure 1). The mine consists of a single surface shaft system with a sub-shaft (Target 1C shaft) and a decline. Ownership was attained by Harmony Gold Mining Company Limited in May 2004 (Harmony Gold Mining Company Limited, 2010). Before discussing the selection of open stopes for the back-analyses, a brief explanation of open stoping as practiced at Target Mine will be given. The orebody is some 180 m in thickness and 270 m wide and comprises multiple reefs overlying one another. The 180 m thick reef package is termed the Eldorado Reefs, as shown in Figure 2. The Eldorado Reefs suboutcrop against the Dreyerskuil Reefs, as shown in Figure 3. The dip of the reef varies from as low as 10° in the west to 75° in the east.Compared with most Australian and Canadian open stoping mining operations, Target Mine is unique. In most Australian and Canadian mining operations the hangingwall and footwall of the open stopes comprise waste rock, and the orebody dips relatively steeply. Due to the depth of Target Mine, some 2300 m to 2500 m below surface, a destress slot (Figure 4) is mined to create an artificial, shallow mining environment whereby the field stress is managed and kept at values of around 60 MPa. The destress slot comprises a narrow tabular stope with an average width of 1.5 m, and is mined on the Dreyerskuil Reefs.At Target Mine the hangingwall, sidewalls, and footwall of the open stopes all comprise reef of different grades, except for the EA1, where the EB footwall is waste rock. If a stope, for example, is mined alongside an existing old stope, the western sidewall of this stope will consist of backfill. The general mining direction of open stopes is from the lowest position of the reef on the west, progressing up towards the east as shown in Figure 5."

Apr 1, 2019

By J. -M. Chautru

A geostatistical simulation of a typical mining site for polymetallic nodules in the North Pacific Ocean is presented. This is the first stage in the design of an industrial mining system. Two variables which have a major effect on the orebody&apos;s economic potential are considered, namely: the maximum slope of the ground inside a mining block of 50 x 100 m; and the average quantity of nodules on the same support. Two geostatistical problems have emerged in this study. The first is due to the lack of a change of support model for the maximum of a variable. A provisional solution, considering an experimentally accessible &apos;equivalent&apos; support, is proposed. The second is due to a non-linear link between the two variables. To be able to take this into account in the simulation, we propose a new method based on the decomposition: X = E(X/Y) + Residue (X). Satisfactory results were obtained with this approach.

Jan 1, 1987

By P. J. Le Roux

"Mining companies are under constant pressure to reduce their cost structures to sustain profitability. In mines using an open stoping mining method, dilution often has a significant effect on profitability. At Target mine in South Africa, dilution in some open stopes was found to exceed 10%, falls of ground being a major contributor to the problem. This dilution can reduce the recovered grade from 5.5 to 4.5 g/t, resulting in a potential loss of about R21 million per month based on a gold price of R240 000 per kilogram. In addition to the cost of dilution, the cost of damage to, or loss of, trackless equipment as a direct result of falls of ground in open stopes is significant. Other associated costs include transport, hoisting, secondary blasting, milling, and plant treatment of waste material. Stable open stopes are essential in order to reduce falls of ground. Back-analyses of stope instability at Target mine have indicated that conventional rock mass failure criteria are unsuitable for stope design. An alternative strain-based criterion has been developed, and has proved to be very successful, allowing the stability of open stopes to be calculated reliably. Since its implementation in 2010, dilution and equipment damage have decreased markedly, creating value for the mine. IntroductionMines that make use of an open stoping mining method aim to extract only the ore, leaving the waste behind. Many orebodies have well-defined boundaries between the ore and the waste rock. In such orebodies, the introduction of waste into the ore due to overbreak dilutes the grade. In massive disseminated orebodies, dilution is less problematic. Overblasting, falls of ground, or other causes may result in dilution. A study undertaken in Canada (Pakalnis et al., 1995) found that approximately 51% of all underground metal mines utilized open stoping mining methods and, from surveys conducted at these mines, open stoping operations experienced dilutions of up to 20%, and occasionally more. Dilution of this magnitude has a significant economic impact on any mining venture. Research carried out in Australia by Capes (2009) came to the same conclusion."

Jan 1, 2017

By C. Snyman, M. Le Roux, Q. P. Campbell, S. Engelbrecht

Due to the ultrafine particle size required for effective processing of chromite ores, dewatering of the concentrates presents a challenge. It is not uncommon for the ore to have elevated moisture contents even after dewatering, which must be reduced to required levels of between 8% and 10% by mass for further processing. Contact sorption drying has shown promise in test work on fine coal. This method was used to study the dewatering of chromite on a laboratory scale using 3 mm spherical activated alumina ceramic beads as a sorbent. Three different sorbent-to-chromite mass ratios, namely 0.5:1, 1:1, and 2:1, were tested with different process conditions, including dewatering in a stationary and a rotatingl bed. The experimental work showed that it was possible to achieve the target moistures in less than 10 minutes, irrespective of the sorbent-to-chromite ratio used. Ratios of 1:1 or higher, however, proved to be the best. The sorbent reusability at mass ratios of 1:1 and 2:1 were therefore tested. With a 1:1 mass ratio, the sorbents could be reused for three cycles, while with 2:1 ratio, the number of cycles increased to six. The sorbent-to-chromite mass ratio used had a significant influence on the required contact time and the reusability of the sorbents.

Oct 3, 2023

By E. K. Mutinda, D. K. Maina, R. M. Kasomo, B. O. Alunda

Assessment of blast fragment size distribution is critical in mining operations because it is the initial step towards mineral extraction. Different empirical models and techniques are available for predicting and investigating the consequences of blasting, one of which is the Kuznetsov Cunningham-Ouchterlony (KCO) model. In this paper we summarize the advances in the empirical models from inception until now, and explore the improvements that have been made so far with particular emphasis is on the most recent KCO model. Utilization of the model and the errors that arise between expected and the actual outcomes are analysed. The results indicate that the KCO model remains useful for predicting the blast fragmentation at limestone mine sites, despite the availability of other advanced prediction models. It is also a valuable instrument for pre-surveying the impact of varying certain parameters of a blast plan.

Mar 1, 2021

By B. M. Wainstein

An extension of lognormal theory and its application to risk analysis models for new mining ventures by B. M. WAINSTEIN*, B.Sc., M.B.A. (Witwatersrand) (Visitor) The lognormal distribution, which remains the most popular distribution model for ore values, is investigated. The T-distribution, an integral part of this theory, is dependent on the sample size, n, and the unknown population parameter, o2, which cannot be integrated out. Hence, o2constitutes a nuisance parameter. In this study, the robustness of the T-distribution to changes in o2 is examined. It is found that the T-distribution is robust for 0,1 <= o2 >= 2,5, a domain covering most practical applications of the lognormal theory. By the use of o2 = 0,7, multiplier factors, which facilitate the computation of the confidence limits, are derived for a comprehensive set of confidence levels.

Jan 4, 1975

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014

The June General Meeting of the Institute was held in Kelvin House, Johannesburg, on 18th June, 1969, at 4.30 p.m. Mr J. K. E. Douglas (Vice-President) was in the Chair. There were also present fourteen Members, Messrs R. J. Adamson, F. P. Bath, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, and Mr P. W. J. van Rensburg (Council Members), Messrs B. F. Berry, A. F. Lee, J. E. van Leeuwen, G. G. Nicolson, N. F. Peverett, Dr A. G. Raper, Messrs E. R. Rudolph and H. R. Reid. Five Associate Members, Messrs T. D. Brown, M. R. Fuller-Good, J. S. Freer, Dr P. R. Jochens and Mr D. A. Viljoen. One Graduate, Mr P. G. Mrkusic. Five Students, Messrs N. A. Barcza, J. A. Cruise, R. P. W. Henrard, D. I. Ossin and J. C. M. Wethmar. Nine Visitors, Messrs M. Badenhorst, N. J. Bovey, H. H. Herold, Dr H. J. S. Kriek, Messrs M. S. Rennie, B. B. Segal, S. Selmer-Olsen, O. A. W. Strydom and B. Yates. Secretary, Mr D. C. Visser. Total present: Thirty-six. MINUTES The Vice-President: "May we confirm the minutes of the Monthly General Meetings held on 24th March, 16th April and 21st May, 1969 as published in the Journal?" Agreed. MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the undermentioned candidates having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Wilfred Desmond Morgan, Abraham Kriek. Associate Members: Rodger Neville Hampson, Robert Richard Booth Lodge. Graduates: Beverley Hugh Waiters, Gwynne Hugh Johnston. Students: Colin Edward Alvery, Peter Marthinus Haikes, Charles Aubrey Husband, John Nowell Randell, Frederick Johannes Jacobus Blaauw, Johannes Andries Breytenbach, Peter Vos, Frederik Hendrik Coetzee, Petrus Nicolaas Jacobus Smit, Patrick Alien Boardman, Robert Nelson Guest. "May I welcome the newly elected members to the Institute." (Applause.) ELECTION OF SCRUTINEERS FOR THE 1969-70 BALLOT FOR COUNCIL The Vice-President: "In terms of By-Law 9.4, I now call for nominations for scrutineers for the 1969-70 ballot for CounciL" P. W. J. van Rensborg: "I wish to nominate Messrs R. C. J. Goode, V. C. Robinson, J. K. E. Douglas, P. Lambooy, D. G. Maxwell, H. Britten and H. Simon as scrutineers."

By D. A. Hayman, N. Rambuda, N. A. Sithole, C. Hockaday, J. D. Steenkamp

"Mogale Alloys operates two alternating current (AC) submerged arc furnaces (SAFs), and two direct current (DC) open bath furnaces. These furnaces are capable of producing two products, silicomanganese (SiMn) and ferrochrome (FeCr), with a total production capacity of 110 000 t/a. This paper focuses on the silicomanganese process specific to Mogale Alloys, with a two-furnace operation facility that produces 55 000 t of SiMn per annum.IntroductionMogale Alloys is situated in Krugersdorp in the West Rand District Municipality in South Africa’s Gauteng Province. The Krugersdorp facilities were initiated by Palmiet Chrome Corporation in February 1963 to produce charge chrome (Basson, Curr, and Gericke, 2007). Mogale Alloys bought the Palmiet Chrome facilities in 2005 from Samancor Chrome. The Afarak Group currently owns 90% of Mogale Alloys.SiMn is produced in two 20 MVA submerged arc furnaces (SAFs), which were originally built for chromite processing, and ferrochromium (FeCr) in two DC open bath furnaces rated at 40 MVA and 10 MVA. When this paper was compiled, the 10 MVA furnace was not operational due to the high cost of production, and one of the 20 MVA SAFs was recently converted to produce FeCr due to market constraints. Mogale Alloys has 290 permanent employees with four contracting companies on site. The paper presented here focuses on the production of SiMn at Mogale Alloys.The high-level process flow at Mogale Alloys is summarized in Figure 1, which details the raw material input and the products produced by the two 20 MVA furnaces. SiMn is produced by carbothermic reduction of manganese-bearing raw materials from four different sources, namely Wessels, Mamatwan, and UMK ores, and BHP sinter feed. The carbon sources are bituminous coal from Forzando and Msobo, local suppliers in Mpumalanga."

Nov 1, 2018

The most important event in the Institute&apos;s recent history is the strategic plan, which was drawn up in 1986 during Henry James&apos;s term of office. This plan was formulated at a workshop attended by most of the senior members of Council, and from it has flowed a number of changes that have been introduced over the past four years.

Jan 1, 1990

By M. S. Shishvan, S. Klerkx, J. Sattarvand

The inaccurately drilled blastholes from the planned locations cause changes in the spatial distribution of explosive energy; some areas of the blast may receive a surplus of explosive energy, while others see a reduction. This results in less uniform fragmentation, reduces the efficiency of mining operations and increases costs. Additionally, it can lead to slope stability issues, flyrock, and uneven benches. To mitigate these problems, this study attempts to reduce differences in the explosive energy distribution (EED) through an optimization approach that adjusts the height of explosive columns in blastholes. Two optimization algorithms, the Genetic Algorithm (GA) and Tabu Search (TS), are tested. The latter is preferred for its local search neighbourhood strategy that gives superior computation times. Applications on different blast patterns result in improvements of 0.53–1.54%, or 2.14–3.94% when only the affected blocks are considered.

Sep 1, 2021