Search Documents

By Y. G. Zhu, G. B. Zheng, X. X. Hu

Reverse flotation by cationic collectors is the classical method to reduce the silicon content in magnesite. But because of the low selectivity, there is a large loss of magnesite in the reverse flotation froth. To improve the efficiency of the collector, a novel collector named BK433 was developed in this paper. In order to determine the performance of the BK433 collector, a systematic experimental study was carried out with a high silicon magnesite in China. The suitable pH environment of slurry was confirmed, the depression effect of different depressants was investigated, and the flotation effect was compared with commonly used traditional collectors. The results show that the BK433 shows remarkable good selectivity and collection ability. After the 4 stages reverse flotation, the SiO2 content decreased from 3.76% to 0.25%, SiO2 impurity removal rate reached 94.69%. Meanwhile, the MgO content increased from 45.06% to 46.73%，the recovery of obtained concentrate (calculated by MgO) was 82.79%. Keywords: Magnesite, Desilicication, Reverse flotation, Collector

Jan 1, 2020

By F. Ntuli, T. V. Nyangadzayi

Chromium green is an essential metal with various applications in the paints, construction, electronics, and aerospace industries. The main source of chromium green is the carbo-thermic reduction of chromite ores, however, chromite ores are being heavily depleted on a global scale, hence the need to find alternative or secondary sources for the chromium. In order to meet the global demand for chromium there is a need to implement principles of the sustainable circular economy to keep chromium within the material loop. Ferrochrome slag and stainless steel slags are secondary resources that are potential sources of chromium. In this work, recovery of chromium from ferrochrome slag was investigated. The ferrochrome slag was alkaline leached using sodium hydroxide- sodium hypochlorite solution to reduce the use of potent reagents that have a potential negative environmental impact. The leachate produced by oxidative alkaline leaching of ferrochrome slag contained hexavalent chromium, which was used to recover the extracted chromium through a two-stage process involving reduction and precipitation. Reduction of hexavalent Cr to trivalent Cr was investigated using anhydrous FeSO4 at concentrations of 5 g/L, 10 g/L, and 15 g/L. Precipitation was conducted by dosing the reduced leach solution with 1 M sodium hydroxide at dosages of 5 ml/L, 10 ml/L, and 15 ml/L. The experiments were designed using the Taguchi (L9) orthogonal array and analysed according to the ANOVA, general linear model. The optimized conditions for the reduction step were ferrous sulfate dosage of 5 g/L with a pH of 12, and for the precipitation step, 1 M sodium hydroxide at a dosage of 15 ml/L with a setting time of 90 minutes and pH of 7. Physical changes were observed during the two-step chromium recovery, with solution changing from a yellowish colour to dark green colour indicating completion of the reaction. The chromium recovery was found to be 93.3%.

Dec 11, 2024

By M. Izadi Yazdan-Abadi, S. H. Amiri, M. Ramezanizadeh, M. Bazmandeh

Iron ore concentrate is used as the fresh feed of pelletising plants. The green pellet properties depend on iron concentrate characteristics such as particle size distribution (PSD), specific surface area (Blaine value), iron grade, moisture content and grinding methods. The grinding methods affects particle size distribution and Blaine value. To find out the effects of grinding methods on pelletising process, green pellets were produced with concentrates that were reground by means of HPGR (high pressure grinding rolls) and ball mill. The Blaine values of ground concentrates in both types of milling were approximately 1400, 1600 and 1800 cm2/gr. The results of green pelletising tests on a pilot plant scale showed that at the same Blaine values, drop numbers of green pellets produced by ground concentrate inside HPGR were higher than the green pellets produced by ground concentrate inside a ball mill. Also, reground concentrates by means of HPGR, in comparison with ball mill, caused the production of green pellets, at higher wet and dry compression strengths. As a result, it was found that preparing the pelletising feed by means of HPGR led to more positive effects on the properties of green pellets. Keywords: Ball mill, HPGR, green pellet, drop number, wet and dry compression strengths

Jan 1, 2020

By S. Fazluddin, K. C. Sole, M. R. Serwale, T. Coetsee

The CSIR-Ti process employs lithiothermic reduction of titanium tetrachloride feedstock to produce titanium sponge. The product is therefore contaminated by a range of lithium and chloride species. In this study we examine the effects of particle size, temperature, and HCl concentration as input leaching variables on the removal of chlorides from the crude titanium sponge. A review of the aqueous chloride chemistry of Li and Ti provided initial conditions for leaching of impurity species from the sponge. Experimental results confirm that the effectiveness of leaching and removal of dissolved impurities from the sponge are dependent on leaching kinetics, which are influenced by temperature, particle size, and morphology. Of the variables tested, reaction temperature had the strongest influence on the oxygen content of the leached product. The HCl lixiviant concentration had a negligible effect under the conditions tested. Leaching of crude titanium sponge (−10 mm size fraction after crushing) at 14°C in either 1 M or 0.032 M HCl yielded a titanium sponge product that met the ASTM standard specification for commercially pure Grade 1 titanium, i.e., oxygen content < 0.18 mass% and chloride content < 0.15 mass%.

Dec 13, 2022

1. Book review • World mineral statistics 1974 to 1978. Production: Exports: Imports. London, H.M.S.O., Institute of Geological Sciences, 1980. (Reviewer: R. P. King) This edition is the third in a regular series prepared by the Institute of Geological Sciences. It is a useful compilation of statistics on the production, export, and import of fifty-eight different mineral commodities. Each mineral is listed by country, and a table is provided for the annual production, the annual imports, and the annual exports for each commodity included. However, some commodities are treated in considerably more detail; for example, aluminium and bauxite have tables under the following headings: Production of Bauxite, Production of Alumina, Production of Primary Aluminium, Exports of Bauxite, Alumina and Aluminium, Imports of Bauxite, Alumina and Aluminium. The information presented is the latest official information available from primary sources; the compilers have not relied on data from secondary compilations. This publication will be of considerable assistance to all who are concerned with the trading of mineral commodities and their production.

Jan 1, 1981

By G. P. Dyke

With the removal of the majority of the shallow mineral reserves there has been an increase in the mining depths in the South African mining industry. This has, in turn, changed the industry?s and stakeholders? perceptions of risk associated with mining-induced instability. In recent years the increased mining depth, particularly in open pits, has led to an increase in pit slope failures, which has highlighted the need for appropriate and effective pit slope management programmes. Such a programme comprises many facets, including mine hazard plans, regular slope inspections, cleaning of interim and final pit faces, blasting practices, histories of failures, pit depressurization, stormwater control and evacuation procedures. However, it is arguably in the field of slope monitoring that the most significant strides have been made in terms of new technologies and best practice in open pit mining geotechnics, with the introduction of technologies such as laser scanners and slope stability radar. This paper seeks to illustrate the operational benefits associated with the implementation of new technologies into open pit mining, using AngloGold Ashanti?s Geita Gold Mine in Tanzania as an example.

Jan 1, 2009

By E. Garab, M. Pillalamarry, E. Develo

"Recent geological exploration at Rosh Pinah mine revealed that the mine’s major production is shifting towards the western orefield, which will increase the demand for air flow to be supplied to this area. A snapshot of the ventilation survey carried out in December 2014 at the western orefield drill drive B (WOF-DDRB) showed that the air flow was well below the required standards. In order to improve the existing conditions, possible options were considered and simulated using Ventsim™ software.The best option found was to replace the existing western orefield fans with the larger fans from the inactive southern orefield workings, to increase the air flow in the DDRB district. Simulation showed that as much as 20 m3/s of air can be received at the working faces of WOF 30, compared to the previously received amount of 1.37 m3/s. The economic analysis indicated that the above option can reduce the ventilation cost by N$1.9 million annually. It was also noticed that after implementing this option together with other projects, the ventilation conditions in the mine were greatly improved and currently give no cause for concern. IntroductionA good mine ventilation system should be capable of providing adequate quantity and quality of air to all working faces, and is critical to the occupational health, safety, and comfort of underground employees (Luxbacher and Ramani, 1977; Exikis and Kapageridis, 2006). No ventilation system can remain adequate indefinitely; as the mine workings are extended, the ventilation characteristics such as system pressures, air volumes, leakages, and airway resistances change considerably. Continuous improvement of the ventilation system is needed to ensure compliance with health and safety regulations (Lovejoy, 2010). It also ensures that the right quality and quantity of air is delivered to all the necessary areas at the lowest possible cost. This can be achieved by identifying inefficient airways and poorly ventilated areas in the mine and planning how best to upgrade them.The latest geological exploration shows that the focus of production at Rosh Pinah mine is shifting towards the western orefield (WOF). As mining progressed, the working areas have advanced away from the main fans, which increased the resistance to air flow drastically and resulted in increasing demands being imposed on the main fan in order to supply an adequate air flow. This process also created more leakage paths between the fan and the working areas, which has caused the air to short-circuit before it can reach the faces. Consequently, a much larger quantity of air has to be circulated by the fan so that the stipulated quantity reaches the face, which increases operating costs (Singh et al., 2004)."

Jan 1, 2016

By N. Naude, W. P. Roux, O. Kaba

Ceramic filtration plates are used for dewatering slurries with high solid concentrations and particles in the size range of 30 μm to 150 μm. After extensive operating times, the ceramic filter plates at Minas Rio in Brazil begin to blind due to the precipitation of barium sulphate on the surface of the ceramic filter plate, which reduces the overall efficiency of the filtration process. Further research is needed to identify the barium precipitate phases on the blocked filter plates and its thermodynamic and kinetic behaviour in the system. A crystallography analysis was performed on the sample and the results showed that there are two different sets of precipitates formed on the filter plate: grey crystals which were large and scatted on the filter plate and red micro crystals that covered the entire surface of the filter plate. The red microcrystals on the sample were identified with XRD, which indicated that the sample contained barium sulphate in the mineral form barite. Experiments were conducted to determine the optimum conditions under which barium precipitation will occur. The conditions tested as a possible driving force for barium sulphate precipitation were the effect of temperature, pH and concentration. The pH and temperature ranges were pushed to both the lower and higher boundaries. The effect of temperatures as low as 15oC was studied and pH levels of 7 and upwards. The first nuclei started appearing at a pH of 7 but significant growth is promoted at higher pH levels. The X-Ray diffraction analysis confirmed the phase of the precipitates formed, and the orthorhombic crystallographic structure formed is a characteristic of barium sulphate. Keywords: Iron ore, barium sulphate, temperature, pH, concentration, morphology, and ceramic filter plate

Jan 1, 2020

By X. Xiang, W. Xia, J. Yin

"TiCl4 slurry containing valuable metals is an unavoidable by-product of the titanium ore chlorination process. The recovery of these valuable metals, which include titanium, niobium, tantalum, and aluminum, is an urgent issue to tackle in the titanium industry. The results of this investigation show that the valuable metallic elements can be recovered from the slurry by evaporation in a sealed container and leaching with dilute hydrochloric acid. After evaporation at 200°C for 60 minutes, nearly 99% of the titanium was recovered in the form of TiCl4, which was formed by the reaction of the TiO2 in the slurry with AlCl3. After evaporation, metals like niobium, aluminum, and tantalum remained in the residue. By leaching with 2.1 mol/L HCl at a L/S ratio of 6:1 mL/g at 80°C for 60 minutes, the soluble metals, such as aluminum, iron, and copper were all removed from the residue, and the niobium and tantalum were further enriched in the leach residue. A concentrate containing 53.40 wt% Nb and 5.57 wt% Ta was obtained by washing the leach residue with dilute aqueous ammonia under stirring. A potential waste water purifying agent containing 263.75 g/L AlCl3 was produced by purifying the leaching solution with Al(OH)3 and modified polyacrylamide. IntrodutionTitanium tetrachloride (TiCl4) is an important intermediate in titanium metallurgy that is widely used in the production of titania and titanium sponge (Akhtar, Xiong, and Pratsinis, 1991). In conventional titanium metallurgical processes, high-titanium materials such as synthetic rutile and high-titanium slag are reacted with chlorine to produce TiCl4 in a fluidized-bed furnace. Accompanying elements, such as Al, Nb, and Fe also react with chlorine to form chlorides, which are mixed with gaseous TiCl4 (Anderson, 1917). In the condensation process, gaseous TiCl4 is refrigerated and high-boiling-point chlorides are precipitated in the liquid TiCl4 to form a slurry containing 50~60 wt% TiCl4 (Wang, Xiang, and Wang, 2012).Various methods have been proposed to recover TiCl4 from the slurry, including microwave heating and spray drying (Wang, Xiang, and Wang, 2012, Wang et al., 2010a). To date, the only way to recover the TiCl4 is to return the slurry to the fluidized-bed furnace. However, this causes fluctuations in the temperature in the furnace, resulting in incomplete reaction between titanium-rich materials and chlorine. Therefore, the slurry is often rinsed with water and neutralized by adding lime, which caused serious environmental pollution and wastes a valuable resource (Roy, Bhatt, and Rajagopal, 2003)."

May 1, 2019

By C. C. Birch

Due to grade estimation uncertainty, two statistical errors can occur. The Type I error is where material is classified as ore and mined, despite the true value being below the break-even grade. This material is dilution. The Type II error is where the material is estimated to be below the cut-off grade and is classified as waste, although the true grade is actually above the break-even grade. This material is not mined and is lost. The uncertainty was assumed to follow a normal distribution in a previous study. For this study, estimated block values are compared to those determined after mining (the best estimate of the true grade). This actual data from four mines shows that the uncertainty follows a Laplace. There is no single solution regarding adjusting the cut-off grade away from the break-even grade, considering estimation uncertainty, that could be applied to all gold mines. However, adjusting the cut-off grade downwards (up to 22% for one mine) is noted when optimizing the profit considering grade uncertainties. This type of adjustment could open up significant mining areas and extend the life of the mine.

Jul 2, 2022

By C. B. van den Berg

n this study, silver and palladium nanoparticulate inks with different metal-binder ratios were screen-printed onto a paper substrate. The printed layers comprised the metal nanoparticles and an ethylcellulose binder. The layers are not typical metal composites due to the low concentration of binder and high porosity. The electrical sheet resistivity of each particle concentration was measured, and the data fitted using the scaling law of percolation theory and the general effective media (GEM) equation. The percolation parameters, i.e. the percolation threshold and the critical exponent, for each system were determined from the fits and compared. The percolation threshold for the palladium layer (39.8 wt%) was lower than that found for the silver layer (44.9 wt%). The critical exponents determined for the palladium and silver layers were both lower than the universal value for three-dimensional percolation systems. Microscopy observations indicate that the difference in the percolation threshold for the two layers can be attributed to variations in their microstructure.

Jan 1, 2014

By P. F. Dicks, N. J. Shackleton, E. H. W. Theron, V. Malysiak

Flotation is a complex physical chemical process in which flotation reagents play a vital role in valuable minerals recovery and concentrate grades. This study examines the performance of new generation AECI Mining Chemicals (previously named Senmin) collectors. They were developed to enhance the valuable minerals recovery and flotation selectivity by tailoring the collectors to target specific valuable mineral species present in an ore and thus create added value for concentrators treating PGM ores. The case study was conducted on a Platreef ore, where batch flotation tests were performed and the concentrates were mineralogically characterised for PGE and BMS using QEMSCAN. Further batch flotation testwork was conducted on Merensky and UG2 ores from various localities in South Africa to confirm the trends observed for Platreef ore. The results have shown that there is a strong correlation between PGE mineral type and AECI Mining Chemicals collector type - clearly demonstrating that one reagent type does not fit all flotation applications. Keywords: Batch flotation, QEMSCAN, collectors, PGE and BMS

Jan 1, 2020

By J. L. Havenga, L. J. van der Walt, J. T. Nel, H. Bissett

"SynopsisNew technologies used to manufacture high-quality components, such as direct laser sintering, require spherical powders of a narrow particle size distribution as this affects the packing density and sintering mechanism. The powder also has to be chemically pure as impurities such as H, O, C, N, and S causes brittleness, influence metal properties such as tensile strength, hardness, and ductility, and also increase surface tension during processing.Two new metal powder processes have been developed over the past few years. Necsa produces zirconium powders via a plasma process for use in the nuclear industry, and the CSIR produces titanium particles for use in the aerospace industry.Spheroidization and densification of these metal powders require remelting of irregular shaped particles at high temperature and solidifying the resulting droplets by rapid quenching. Spherical metal powders can be obtained by various energy-intensive methods such as atomization of molten metal at high temperatures or rotating electrode methods. Rapid heating and cooling, which prevents contamination of the powder by impurities, is, however, difficult when using these methods for highmelting- point metals. For this reason plasma methods should be considered.Thermal plasmas, characterized by their extremely high temperatures (3000–10 000 K) and rapid heating and cooling rates (approx. 106 K/s) under oxidizing, reducing, or inert conditions, are suitable for spheroidization of metal powders with relatively high melting points. Thermal plasmas for this purpose can be produced by direct current (DC) plasma arc torches or radio frequency (RF) inductively coupled discharges. In order to obtain chemically pure spheroidized powder, plasma gases such as N2, H2, O2, and CH4 cannot be considered, while Ar, Ne, and He are suitable. Neon is, however, expensive, while helium ionizes easily and it is therefore difficult to obtain a thermal helium plasma at temperatures higher than 3000 K. Therefore argon should be used as plasma gas. Residence times of particles in the plasma region range from 5–20 ms, but this is usually sufficient as 7–8 ms is required for heating and melting of titanium or zirconium metal particles in the 30 µm size range at 3500 K. In this study the melting and spheriodization of titanium powders was investigated by DC non-transferred arc and RF induction plasma methods. The powders were characterized before and after plasma treatment by optical microscopy and scanning electron microscopy (SEM) to observe if any melting or spheroidization had occurred."

Jan 1, 2015

By S. Combrink, N. Naude

Hydrocyclones are widely used in wet mineral classification applications and can be notoriously prone to wear. The methods currently used for quantifying hydrocyclone wear profiles are mostly twodimensional. In this paper it was attempted to quantify and monitor wear in three-dimensions, using a micro-CT scanner (Nikon XTH 225 ST). Hydrocyclone wear and, more specifically, spigot wear was investigated on a Multotec HC250 (Dc 250 mm, barrel diameter) hydrocyclone. The hydrocyclone is lined by a vulcanised natural rubber compound within a metal shell, with a thermosetting polyurethane spigot and vortex finder. Tests were conducted on the hydrocyclone in a pilot-scale recirculating test setup. The wear rate of the spigot was quantified by measuring the volume change within the spigot over 122 days in operation, using the micro-CT scanner. After 122 days in operation (recirculating feed materials) the wear in the hydrocyclone led to only a 13.67% loss of spigot volume. The relatively low wear rate could be related to the fact that material recirculation led to particle smoothing and a reduction in size, thereby decreasing the wear rate. This also shows the enormous influence that particle shape and size have on wear. The research was conducted with the support of Multotec, NECSA and the University of Pretoria. Keywords: Wear, hydrocyclone, micro-CT

Jan 1, 2020

By L. Rojas Mendoza, F. J. Hrach, A. Gupta, K. P. Flynn

ST Equipment & Technology (STET)’s tribo-electrostatic belt separator technology allows for the beneficiation of fine mineral powders by means of an entirely water-free technology with high throughput and low energy consumption. The STET separator is suited for separation of very fine (<1 μm) to moderately coarse (500 μm) particles, in contrast to other electrostatic processes that are typically limited to particles >75 μm in size. STET has performed exploratory studies with several iron ores including tailings and experimental results to date have demonstrated that low-grade iron fines can be upgraded by means of STET tribo-electrostatic separator to commercial grades (58-65%Fe). Experimental results together with high-level economic evaluations indicate that scavenging processes involving low drying costs, DSO operations and tailings beneficiation offer a commercially viable processing method to recover fine iron that would otherwise be lost by traditional processing. Dry electrostatic processing of iron ore presents a clean, low-energy opportunity for iron producers to reduce costs and wet tailings generation associated with traditional gravimetric, flotation and wet magnetic separation circuits. Moreover, STET technology allows for mining waste utilisation and resource recovery from iron ore fines and tailings, therefore offering processors a novel method to recover fines that would otherwise be difficult to process to sellable grades with existing technologies. Keywords: Iron fines, industrial minerals, dry separation, calcium carbonate, talc, barite, quartz, tribo-electrostatic charging, belt separator, fly ash

Jan 1, 2020

By L. J. Su, J. Y. Zhang, P. W. Gu, J. F. Xu

Surface tension of mold flux is a key factor affecting optimum casting conditions. A thermodynamic model was developed to determine the surface tension of mold flux containing fluoride based on the ion and molecule coexistence theory of slag structure and Butler’s equation. The relationship between composition and surface tension was investigated by this model. Results indicated that the calculated values showed good agreement with literature data, and the average error was 8.19%. The surface tension value of the CaO–Al2O3-based mold flux was larger than that of the CaO– SiO2-based mold flux. The surface tension in a multi-component system decreased with increasing contents of SiO2, CaF2, and Na2O, which are considered surface-active components. This trend was more significant in the CaO–Al2O3-based mold flux.

Dec 11, 2024

By H. P. Kritzinger, T. C. Kingsley

Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications. This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron-ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates.

Jan 1, 2014

By F. Sundqvist, B. Skawina, J. Greberg, A. Salama, M. Astrand, P. Ekbeck

Today’s mining operations require fast reporting and rapid rescheduling based on updated information. An automatic mine scheduling system could not only quickly reschedule but also propose alternative solutions. To avoid the financial and physical risks associated with testing such a system directly in operation, it could be first evaluated via discrete event simulation models. This would offer a safe environment to evaluate different operating rules and algorithms. In this study, this is achieved by integrating automatic scheduling software with a discrete event simulation model.

Jun 1, 2021

By G. T. Lineberry, C. M. Baird, D. L. Silverstein

The University of Kentucky (UK), with an enrollment of 25,891 in fall 2002, is a comprehensive, public land-grant university located in the Bluegrass Region of Central Kentucky. As the State’s flagship university, UK has long been involved in distance education, first through traditional correspondence courses, followed by use of videotape and satellite delivery in the 1970s and1980s, but soon supplanted by use of interactive television (ITV) and on-line course delivery in the 1990s to date. Today, UK Distance Learning Programs annually administers approximately600 course sections, with services provided to over 5200 enrollees. Courses are offered via six media: interactive video, Internet, on-site, satellite, open-air and cable television, and videotape, with hybrid delivery becoming increasingly popular. The University of Kentucky College of Engineering experience with distance instruction prior to 1985 was limited to videotape non-credit offerings. The Department of Mining Engineering, a small department in terms of numbers of both faculty and students, was a University pioneer in distance education. The first University degree program offered in its entirety by distance delivery(initially by itinerant faculty) was the Master of Mining Engineering. Satellite delivery from Lexington to Cumberland, Kentucky, was a welcomed change of delivery mode in 1987–88,resulting in six hours less travel time for faculty each week. Shortly thereafter, other initiatives directed toward fulfilment of its land-grant mission were undertaken by the College. Use of satellite for course delivery rapidly declined due to limited interactivity, in favour of compressed video and on-site instruction. Classroom sites in the Kentucky Tele-Linking Network (KTLN) now number over 200. The Network links schools, colleges and universities, as well as public and private agencies throughout the State. The KTLN supports voice, video, and data transmission in a uniformly-equipped environment. Beginning in the early 1990s, transfer-critical pre-engineering courses were delivered from Lexington to Kentucky’s community colleges with the largest pre-engineering enrolments. Success was limited, but lessons learned were invaluable. In 1996, the University of Kentucky College of Engineering was asked by the Kentucky Council on Higher Education (the predecessor to the Council on Postsecondary Education) to expand engineering education in Kentucky, first by initiating cooperative B.Sc. degree programmes in Chemical Engineering and Mechanical Engineering on the campus of Paducah Community College (PCC), located 400 km from the UK campus in Lexington. The third partner in these programmes is Murray State University (MuSU), a public regional comprehensive university 80 km south of Paducah. The genesis of the new degree programmes, which were subjected to ABET review in October 2002, as well as a summary of the major accomplishments and challenges of the innovative programmes, will be offered. The limited use of distance technologies for course delivery in these B.Sc. degree programmes will be discussed. A ‘no-spin’ overview of other non-traditional distance-learning ventures within the College of Engineering will be chronicled, with an honest assessment of the motivation for these efforts and, where appropriate, their relative degree of success. Among these ventures are: a BScME and a Master of Engineering programme at Toyota Motor Manufacturing of Kentucky, Georgetown, Kentucky; course exchange in Chemical Engineering between the University of Kentucky and the University of Louisville; an ITV-based Master of Engineering programme for practicing engineers in Kentucky; proposed joint-degree programmes in Civil Engineering and Mechanical Engineering with Western Kentucky University; and a proposed part-time MScME programme in Paducah, Kentucky, with a start date of August 2002, threshold enrolment permitting. Keywords: distance learning, distance education.

Jan 1, 2003

By M. R. MacIver, M. Pawlik, S. Finora, H. Alizadeh

The dispersion of mature fine oil sands tailings (MFT) by the addition of sodium lignosulfonate was studied using contact angle measurements, optical scattering, and particle size measurements. Lignosulfonate caused the release of residual bitumen to the slurry surface and settlement of fines. Dynamic contact angle by captive bubble measurements were carried out on bitumen to determine the effect of the dispersant on the wettability of bitumen. Lignosulfonate caused a change in the aggregation state of the MFT and increased sedimentation of particles, as indicated by optical scattering measurements. Zeta potential measurements indicate that this change was caused by an increase in adsorption of lignosulfonate onto particles, which caused improved settling of the colloid. Ultraviolet Visible (UV) spectrophotometry and organic carbon content measurements showed that only a small amount of the reagent remains in the aqueous phase of the tailings, which is critical for decontamination of recycled water. Keywords: Oil sands tailings, bitumen recovery, dewatering, dispersion, surface chemistry

Jan 1, 2020