Search Documents

By M. Dobbins

Magnetic separation has long been used to upgrade and beneficiate a wide variety of industrial minerals. Advances in both wet and dry magnetic separators over the years has broadened their use, and questions are often raised about which separation technique or equipment type is most appropriate for a particular operation. This paper will provide a brief look at existing magnetic separation technologies, and discuss their potential advantages and disadvantages when applied to heavy mineral applications. Relevant case studies for the separation of ilmenite and chromite are then presented. The process development efforts undertaken for each case are described, and the rationale for selecting appropriate magnetic separation technology is explained. The nature of the material being treated must clearly be understood, knowledge and access to testing the best separation technologies is required, and careful process development and economic evaluations are a must. As is shown in the case study discussions, it is imperative that these principles drive the separation technology selection and placement, rather than looking at typical or existing similar flowsheets as rules. As examples, the ilmenite tailings case study presented in this paper shows how advances in technology have allowed for increased recovery of -45 µm ilmenite by utilizing a multi-stage SLon® wet magnetic separator circuit equating to an additional 30 000 tons of ilmenite produced per year. The virgin chromite case study presented shows that through careful testing and circuit design efforts using RED technology, a 20% increase in overall chromite recovery was achieved over previous demonstration work.

Jan 1, 2007

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

Many industries base their decisions on the assaying of tiny analytical sub-samples. The problem is that most of the time several sampling and sub-sampling stages are required before the laboratory provides its ultimate assays using advanced chemical and physical methods of analysis. As long as each sampling and sub-sampling stage is the object of due diligence using the Theory of Sampling it is likely that the integrity of the sought after information has not been altered and the generated database is still capable to fulfil its informative mission. Unfortunately, more often than not, unawareness of the basic properties of heterogeneous materials combined with the unawareness of stringent requirements listed in the theory of sampling, lead to the conclusion that massive discrepancies may be observed between the expensive outcome of a long chain of sampling and analytical custody, and reality. There are no areas that are more vulnerable to such misfortune than sampling and assaying for trace amounts of constituents of interest in the environment, in high purity materials, in precious metals exploration, food chain, chemicals and pharmaceutical products. Without the preventive suggestions of the theory of sampling serious difficulties may arise when making Gaussian approximations or even log-normal manipulations in the subsequent interpretations. A complementary understanding of Poisson processes injected in the theory of sampling may greatly help the practitioner understand structural sampling problems and prevent unfortunate mistakes from being repeated over and over until a crisis is reached. This paper presents an overview of the theoretical, practical and economic difficulties often vastly underestimated in the search for quantifying trace amounts of valuable or unwelcome components.

Jan 1, 2009

By M. J. Santofimia

Multiphase microstructures in steel have been intensively studied in the past years, but combining non-equilibrium phases still offers a great potential for further development of these steel grades. Thus, improved combinations of mechanical properties can be obtained with microstructures formed by bainite or martensite, in combination with retained austenite. In particular, microstructures on the basis of carbon-depleted martensite and retained austenite can be produced by the very promising production process named quenching and partitioning (Q&P). Originally, the Q&P process aimed to avoid the formation of bainite during the heat treatment. However, the process does provide the possibility for (carbide-free) bainite formation during the partitioning step, i.e. in the presence of martensite. This article evaluates this approach, considering thatthe formation of bainite from austenite is strongly influenced by the preceding formation of martensite. Although the accelerating effect of the presence of martensite during bainite formation has been observed, it is not yet fully understood, and experimental and theoretical studies are being performed in order to come to a more effective exploitation of these processes for the formation of multiphase microstructures.

Jan 1, 2013

By P V. Savage, T Glück, RCA Minnitt, C Bothma

Manganese Metal Operations ?Manganese Metal Company (MMC), a subsidiary of Samancor BHP Billiton, has two production facilities for electrolytic manganese metal in South Africa and produces a range of about 44 Mn metal products. ?The company is accredited with ISO 9000 and uses Six SigmaTM for continuous improvement. ?The control of the process relies on the effective functioning of approximately 250 different control loops at 50% automation.. ?Approximately 50000 samples are analysed every month. ?There are pyro, hydro and physical unit operations for the production of electrolytic manganese metal flake and value added products ? [ ]

Jan 1, 2005

By R. Heunis

The hazard of rock bursts and rock falls as experienced in South African gold mines is examined in the light of recent research findings. The problem areas include high fatality rates, losses in production and equipment, and a detrimental influence on the recruitment of labour. The nature of the hazard is analysed, and it is shown that rock bursts are strongly related to the spatial rate of energy release by mining but that rock falls are not. The role of blasting and geological discontinuities is discussed. Practical rock-burst control strategies are compared, including the use of stabilizing pillars, back-filling and, in particular, techniques for reducing the frequency and severity of accidents resulting from large rock bursts. The latest stope-support experiments and their potential implications to mining are consid~red. It is concluded that a better understanding of the rock-burst and rock-fall hazard has resulted from the industry's research efforts. The findings can be applied towards obtaining an improved underground environment for men and machines.

Jan 1, 1980

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of 'Google maps?' underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum's new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2013

By P. R. Mothemela

The objective of the investigation is to optimize the truck and shovel operations for pre-stripping at New Vaal Colliery by introducing campaign mining. The aim of campaign mining is to improve the efficiency of the loading, hauling, dumping, and maintenance operations which are critical to the success of truck and shovel operations. The current loading (single-sided loading method), hauling, and dumping operations at New Vaal Colliery were found to be inefficient. Time studies were used as a major indicator to highlight the inefficiency of the truck and shovel operations, and it is recommended that an improved loading configuration, hauling, and dumping operations be implemented by using campaign mining. It is also recommended that a service truck be used to maintain the pre-stripping fleet in order to reduce travelling times to the main workshop. As expected, the improved operating conditions will lead to an increase in pre-stripping production.

Jan 1, 2013

By D. T. Jordan, L. C. Coetzee, G. Kalenga, T. Mahlangu, W. J. Shipman

Although online free cyanide analysers are widely available and used in gold leaching operations worldwide, reliable automated free cyanide concentration control is not consistently achieved in many of these operations. Effective cyanide concentration control is complex owing to amongst others, the long residence times and ore feed variations. Model Predictive Control (MPC) has been proven to provide superior cyanide concentration control over traditional proportional-integral-derivative (PID) control, leading to savings in operational costs and reduced leachable gold losses. In the first example reported in this paper, MPC has improved control of the free cyanide concentration by keeping it within the required range 73% of the time during testing, compared to the previous PID controller that only achieved this target 30% of the time. This represents a 143% improvement. Another example demonstrates a 22% reduction in cyanide usage as a result of using MPC. MPC functionality is rarely available on the programmable logic controllers (PLCs) and control systems installed at gold plants, hence it is implemented on a personal computer (PC) networked to the cyanide analyser and plant infrastructure. Mintek has developed an embedded MPC that installs into the Mintek Cynoprobe analyser, adding MPC functionality without the need for additional PC and network infrastructure, reducing installation costs. This allows plants to minimise their expenditure on additional infrastructure while gaining the benefits of superior MPC technology for multiple cyanide dosage points. This paper will present results showing that the embedded MPC performs as well as Mintek’s existing PC-based StarCS MPC controller, making it a viable alternative for infrastructure-constrained gold plants. Keywords: Model predictive control, gold cyanidation

Jan 1, 2020

By F. L. D. Cloete

he above article by E. Barnea, which appeared in the January 1978 issue of the Journal (vol. 78, no. 6, pp. 143-145), calls for comment in view of the author's claims for the novelty of his proof. He states in his article that its main purpose is to give a mathematically acceptable proof by induction of the 'recently proposed' equation

Jan 1, 1978

By J. Markgraaff

Because composites offer new solutions to materials problems, they are currently the focus of intense research and development worldwide. However, the natural tendency of users is to remain with tried materials in every situation of material selection. This approach ignores the tremendous advances that have been made in composite materials and their application. These advances enable engineers to tailor composites to suit specific applications such as the demanding needs of mining and industry in South Africa. However, the application of composites, where new and improved components and products are needed or are being developed is often hampered by the limited knowledge and experience of the engineers concerned. This paper presents some of the basic information needed for an appreciation of the terminology, definitions, and properties of various types of composites. It also reviews recent developments in manufacturing technology and product development that may find application in local industries and mining.

Jan 1, 1996

Now a new generation of computerized drill rigs has been launched and they are based on modern standard PC-computer technology. The rigs have been well embraced by the market and more than 100 units have left the assembly line. The new generation has taken a quantum leap forward with respect to drilling accuracy, logging capabilities, reduction of manpower in some types and serviceability compared to the previous generation of drill rigs. The Can bus technology, well proven in the automobile products, is the backbone in the new generation control system of Atlas Copco. The short-term development is now focused on establishing this new automation platform on other product lines of Atlas Copco products. The long-term objectives is to offer the mining industry Atlas Copco products with one common automation platform. Essential for Atlas Copcois to contribute to the work with the on-going Data Exchange standard between mining machines and mining computer systems (IREDES). Our belief is that an accepted standard will make mine automation programs affordable for a wider base of the mining industry, because of the possibilities to a cost effective integration of different equipment with a minimum of system integration problems and machine specific interfaces.

Sep 1, 2001

By P. Ramphisa

In South Africa reprocessing used oil into industrial fuel is commercially attractive. The reprocessed product is sold as a substitute for heavy fuel oil that is derived from crude oil (Rose Foundation, 2008). The objective of this investigation is to evaluate the use of petroleum products such as oil, petrol and diesel in Driefontein Gold Mine. The recovery of oil through recycling has costs implications to the mine while the release of petroleum hydrocarbons due to the poor management of the use of petroleum products has potential to cause pollution and negatively affect soil and water. Environmental legislation such as the Minerals and Petroleum Resources Development Act (Act 28, 2002) requires that such negative impacts to the environment be rehabilitated. The rehabilitation cost of pollution caused by petroleum products to the environment increases operational costs in business. Field assessment is conducted to identify the main sources of petroleum product contamination such as leaks in piping, overfills and petroleum spills. The areas that require mitigation would be mapped in the study. Recommendations for mitigation measures will focus on using the best practicable environmental option (BPEO) as well as the best available technology not exceeding excessive cost (BATNEEC). The recovery of oil from the mining industry is generally low and very poor. In this study, the effect of proper management of petroleum products to the mine?s operational costs is investigated and compared to there mediation costs of the impacts caused due to poor management of these products. The study investigates the financial benefit that could be obtained from proper environmental practices and efficient usage of petroleum products in the mining.

Jan 1, 2009

By F. Q. P. Leiding

SYNOPSIS A technique is described for measuring the change in volume in a borehole drilled in a rock mass subjected to stress and strain. It is shown that the volumetric strain or change in volume provides a practical estimate of the the stress in the rock.

By P. A. Laxen, P. J. van Staden

Alternative procedures for the recovery of gold from old sand dumps are discussed, with emphasis on the use of heap leaching. The modification of material to improve its permeability prior to heap leaching is not currently receiving much attention in South Africa. The channeling of solutions through heaps and the high consumption of reagents sometimes ascribed to heap leaching can, as shown by the results described in this paper, be lessened by desliming of the sand prior to heap leaching and the treatment of the resulting slimes fraction by agitation leaching and carbon-in-pulp. This combined procedure results in a higher overal recovery of gold. Alternatively, the sand can be heap-leached as it is after agglomeration with lime and cement, which improves the mixing and neutralization of the material, as well as lessening the probability of channeling.

Jan 1, 1988

By M. C. Harris

Float-sink analysis has wide application in the coal laboratory. This paper evaluates the established methods used for the float-sink analysis of fine coal, and then describes a new method and apparatus that can be used for material down to a few micrometres in size. The method is rapid and accurate, and requires only a small amount of sample. The results presented show close agreement with the float-sink analyses obtained by the more classical technique using separating columns. The new centrifugal method reduces the time required for the analysis by a factor of ten.

Jan 1, 1986

A description is given of a simple, cheap device that enables the intact shear strength of rock to be determined quickly and inexpensively. Thin rock plates, prepared with a diamond saw, are tested in double shear by a linear punching action. By varying the direction of the diamond-saw cut in a number of specimens, the change in shear strength can be measured for different orientations relative to the rock fabric.

Jan 1, 1980

By G. J. de Korte

South Africa is reliant on coal for the generation of almost all the electricity used in the country, and several large industrial concerns such as Sasol are also coal based. Research relating to the mining, beneficiation and utilization of coal is important in order to ensure the optimal exploitation and use of coal within the country. The Fuel Research Institute (FRI) of South Africa was established in 1930 to investigate all aspects of coal beneficiation and utilization in South Africa. The FRI went on to conduct world-class research and in 1957 a pilot coal preparation plant was constructed in Pretoria to enable large-scale practical experimentation. The pilot plant played a pivotal role in the establishment of South Africa?s low ash coal export project. Political and economic factors contributed to the eventual closure of the FRI and South Africa experienced a period of about 10 years between 1990 and 1999 during which very little public coal preparation research was done. This changed for the better towards the end of 1999 when Coaltech 2020, a collaborative research program was established. Participants included the CSIR, universities, the government and the major coal producers. Coal preparation research conducted under Coaltech thus far include dewatering and drying of fine coal, size classification of ultra-fine coal and dense-medium fine coal beneficiation. Currently, the Coaltech focus is on the beneficiation of low-grade coal reserves and is investigating existing as well as new techniques that can be utilized to provide cost-effective beneficiation of low-grade raw coals and reject coals.

Jan 1, 2010

"Chairman: Professor E. P. PFLEIDER Rapporteur: Mr P. R. JANISCHPapers:Optimum design of an open pit by D. A. PhillipsAn open pit design system for stratiform ore bodies by L. A. J. Pronk van Hoogeveen, J. R. Cutland and M. WeirAn open pit design model by R. H. Robinson and N. B. PrennThe Chairman in opening the session highlighted the current situation in the United States of America where some 85 to 90 per cent of all mining (except for coal) is done by open pit methods, and where some 40 per cent of the coal is mined by open pit. The South African industry is, of course, dominated by the deeper level underground gold mines; however, with the aid of an extensive open-pit technology developed in other countries, South African companies arc continuing to explore possibilities of open-pit exploitation of base mineral, coal and diamond deposits. Several successful ventures are already in operation at Phalabora, Optimum Colliery, Kimberley and elsewhere, and South Africa is undoubtedly benefitting in this regard by drawing on the experience of others.The papers of this session were therefore particularly pertinent, particularly when viewed in conjunction with those presented at an earlier South African conference devoted specifically to open pit mining.Two themes dominated the discussion which followed presentation of the three papers at this session. The first related to the practicability of using the reported techniques as a tool for management, and their acceptability as such to mine management. This was, of course, not peculiar to this particular session, but rather the major point of debate over the entire conference.The second theme concerned the reliability of the initial drill hole data on which any open-pit design must necessarily be based. This gave added emphasis to the problem of practicability, for no management is likely to accept an elaborate pit design unless confidence can be placed in the ore reserve assessment.In noting these two features of the discussion, it should be remembered that all the three papers dealt largely with design and pre-planning; there was an unfortunate lack of papers or discussion on the subject of controlling the day-to-day mining of open pits, and this is an area where the potential impact which can be made by the computer is even greater.In introducing his paper, Mr D. A. Phillips pointed out that it was concerned only with optimization, and that it therefore assumed, firstly, an adequate subdivision of the orebody into ore blocks characterized by grade, rock type, structure, etc., and, secondly, an acceptable forecast of costs and mineral prices in order to generate a suitable profit matrix. However, programs dealing with these problems for both massive, disseminated and stratiform ore bodies are available to Roan Consolidated Mines. The method of optimization which he had described had been used on a region split into 28 000 blocks, for which the program used three hours of C.P.U. time on an IBM 360/40 computer. The computer design had provided a three per cent improve¬ment on a normal design of the same area."

Jan 1, 2014

By P. S. Turner

After a brief account of the differences between the control of underground fires and those on the surface, the paper describes the analogue detection system used on the mines of the Anglo American Corporation of South Africa Limited. The system comprises Spanair gas analysers, Becon combustion-particle detectors, a telemetering system, a surface signal-recording and-processing system, and an alarm system. The use of the system is described and illustrated.

Jan 1, 1982