Search Documents

By G. L. Gomes-Sebastiao, W. W. de Graaf

"Gomes Sand is a quarry operation that produces sand and aggregate for the construction industry. The quarry is experiencing inconsistencies in the fragmentation and poor pit conditions as a result of poor drilling and blasting practices. This results in excessive downtime in the load and haul and crushing processes.A benchmarking exercise of the blasting practices was conducted to evaluate the effect of the inconsistency on the mining cycle. After changes in the blasting practices the downtime was reduced, which improved the crushing plant utilization by 4.9%. The improved blasting practices and more consistent fragmentation decreased the average number of loads lost each month due to jaw crusher blockages from 9.2% to 3.9% of plant throughput. The change in blasting practices also improved pit conditions. IntroductionGomes Sand is a quarry operation that has been in operation since 2009, producing sand and stone for the construction industry. The quarry was experiencing unacceptable blasting results. The repercussions included uneven pit floors, large amounts of oversize rock (>500 mm), and inconsistent fragmentation.The blast results affected the load and haul operations as well as the efficiency of the crusher. This resulted in downtime in the daily operations, and consequent production and revenue losses.The crusher product should have a top size of 50 mm. A blast fragmentation of <50 mm would improve the downstream operations and the crusher throughput.An investigation into the blasting practices was carried out to assess whether the downstream delays can be eliminated by improving the blast results. The exercise included:* Assessing if the designed blast layout is adhered to on the bench* Observing the quality and control of drilling* Observing the charging procedure of the blast-holes* Benchmarking the fragmentation consistency of the blasted rock using current blast design and practices* Analysing the throughput of the crushing plant* Investigating the power consumption of the crushing plant and determine if a change in blasting practices will affect this* Evaluating the hours spent by the hydraulic hammer on secondary breaking."

Jan 1, 2017

By M. J. Southwood

SYNOPSIS Experiments carried out under atmospheric pressure and temperature (25°C) and sterile conditions show that the dissolution rate of nickel and copper from a pyrrhotite-pentlandite-chalcopyrite ore in a lixiviant of sulphuric acid is greatly enhanced in the presence of pyrite. At a pH value of 1,8 and in the presence of pyrite of equal mass to that of the ore, the recoveries of nickel and copper improved dramatically (21 and 80 per cent respectively). At a pH value of 4,0 the recovery of nickel was enhanced, but the chalcopyrite was refractory. A galvanic mechanism is probable, but cannot be proved from these experiments. The economic implications of the results are discussed.

Jan 1, 1985

1. Books on management The following are available from Knowledge Resources, P.O. Box 3954, Randburg 2125. . Competitive advantage of nations, by Professor Michael Porter from Harvard Business School. This book highlights the importance of industries in contributing towards national competitiveness. It is being regarded as one of the 10 best business books published during 1990. . The borderless world, by Kenichi Ohmae, Managing Director of McKinsey in Japan. This deals with business in the new interlinked economy. . Megatrends 2000, by John Naisbitt and Patricia Aburdene. This book outlines the mega/macro trends that will

Jan 1, 1991

By M. Khodadazadeh, K. G. van den Boogaart, T. Leißner, L. Tusa, J. Gutzmer, R. Gloaguen, M. Kern

Ore sorting is a technology that is increasingly used to process primary raw materials. Timeconsuming and expensive empirical state-of-the-art test work is carried out to assess whether the use of ore sorting for the enrichment of a particular ore makes technical and economic sense. With the innovative simulation-based approach presented here, it is possible to direct the selection of a suitable sensor based on quantitative mineralogical and textural data, thus avoiding much of the empirical studies. Required data can be collected quickly and cost-effectively using available methods of automated mineralogy. The obtained parameters such as mineral grain size distribution, modal mineralogy, mineral area and mineral density distribution have been utilised in this study to simulate the prospects of success of ore sorting, applying different types of sensors. Empirical tests with commercially available sensor systems have been conducted to experimentally validate the predictions of the simulations. The estimation of the target mineral grade can be further optimised by the use of machine learning algorithms for the integration of automated mineralogy data and sensor data. The approach can easily be adapted to other types of raw materials and thus has great potential to become a key technology for the optimisation of processing experiments. Keywords: Automated mineralogy, hyperspectral imaging, machine learning, ore sorting

Jan 1, 2020

By F. Reyes, M. Hilden, G. Forbes, M. Yahyaei

Since AlphaGo defeated the best human player in the game of Go in 2016 - something thought to be an impossible achievement - machine learning, deep learning and reinforcement learning have caught the attention of scientists, the media and the general public alike. This recent development in machine learning (let us remember that neural networks have been available for decades now) opens new possibilities in the areas of modelling and process control. However, little has been reported in the minerals processing industry about these new possibilities and opportunities. This paper presents and introduces the topic of reinforcement learning and the different platforms that allow its implementation. The paper shows the consequences of using reinforcement learning for the specific area of process control and optimisation. As an example, the authors present the use of reinforcement learning for the control of a SAG mill closed with a pebble crusher using industrial data from an operation. A comparison with advanced model-based process control is provided, showing the benefits and shortcomings of reinforcement learning as a new control and optimisation technique. Keywords: Reinforcement learning, deep learning, process control, process optimisation

Jan 1, 2020

By G. W. Healy

The smelting of calcium carbide has always been plagued by eruptions, too often with serious injury y or loss of life. To find their causes, the author calculated an internal energy balance using 1992 data for CaC2 and CaO, and older data for the remaining items. The heat content of the charge, and that of the hot gases formed at the reduction temperature, showed that only a fraction of its heat content can be supplied by these gases. Laboratory data on the electrical resistivity of fine mixtures of coke and non-conductive solids were extrapolated to a commercial carbide charge, and then used to calculate the heat produced by current flowing through the mix from the electrode surface to the hearth, which, under favourable conditions, sufficed to bring the charge to 1900 K and higher, at which temperatures reduction could take place.

Jan 1, 1995

By G. van Aswegen, J. D. Bosman

Gold bearing deposits in the Witwatersrand consist predominantly of narrow tabular conglomerates with quartzite host rock. Extensive mining of these deposits at depth results in significant stresses being induced in the periphery of the tabular excavations. Where remnant pillars are created excessive stresses have resulted in the dynamic failure of the abutments. At the Hartebeestfontein Mine four brittle shear zones have recently been exposed and investigated. For most part, they represent abutment failure into the weaker hangingwall strata, striking parallel to the abutment, dipping towards the stope, with a sense of displacement consistent with closure of the stope from above. These shear zones are similar to those described in various publications by Ortlepp2: they are essentially brittle shear zones characterised by the presence of very finely comminuted ‘rock flour’ on an obviously freshly sheared surface. The angle between the shear zone wall and extension fractures indicate the sense of shear and the intersection of the extension fractures with the shear zone walls define a strong lineation normal to the direction of slip. It is suggested that these structures are referred to as ‘mining induced dynamic brittle shears’. Les gisements d’or du Witwatersrand consistent principalement de conglomérats tabulaires peu épais contenus dans une quartzite mère. Une exploitation poussée de ces gisements en profondeur a pour résultat l’apparition d’importantes contraintes induites à la périphérie des excavations tabulaires. Là où des piliers restants sont créés, des contraintes excessives ont eu pour résultat une rupture dynamique des appuis. Dans la Mine d’Hartebeestfontein, quatre zones fragiles de cisaillement ont été récemment exposées et étudiées. Dans la plupart des cas, elles représentent une rupture des appuis dans les strates moins solides de la paroi suspendue, orientée parallèlement à l’appui, inclinée en direction du chantier d’abattage avec une direction de mouvement consistante avec l’affaissement du toit de la galerie d’abattage. Ces zones de cisaillement sont similaires à celles décrites par Ortlepp2 dans diverses publications: Ce sont essentiellement des zones cisaillement fragiles caractérisées par la présence de « farine de roche » très finement réduite sur une surface évidemment fraîchement cisaillée. L’angle entre la paroi de la zone de cisaillement et les fractures de tension indiquent le sens du cisaillement et l’intersection des fractures de tension avec les parois de la zone de cisaillement définit une forte délinéation perpendiculaire à la direction du glissement. Il est suggéré que l’on se réfère à de telles structures comme des « cisaillements dynamiques fragiles induits par l‘exploitation ». Goldablagerungen im Witwatersrand bestehen überwiegend aus schmalen tabularen Konglomeraten mit Quarzitwirtgestein. Der umfangreiche Abbau dieser Ablagerungen in der Tiefe resultiert in signifikanten Drücken, die auf die Peripherie der tabularen Aushöhlungen wirken. Wo Restpfeiler hergestellt wurden, resultierten exzessive Drücke im dynamischen Versagen der Auflager. In der Hartebeestfontein Grube wurden kürzlich vier spröde Scherzonen freigelegt und untersucht. Zum größten Teil representieren sie Auflagerversagen im Stratum der schwächeren Stollenfirste, parallel zum Auflager verlaufend, in Richtung Abbaustelle abfallend, mit einem gewissen Grad an Verschiebung konsistent mit der Schliessung der Strosse von oben. Diese Scherzonen sind jenen ähnlich, die in den verschiedenen Publikationen von Ortlepp2 beschrieben werden: sie sind im Wesentlichen spröde Scherzonen, charakterisiert durch das Vorhandensein des sehr fein pulverisierten „Gesteinsmehls“ auf einer offensichtlich frisch abgescherten Oberfläche. Der Winkel zwischen der Scherzonenwand und den Bruchverlängerungen deutet die Richtung der Scherung an und die Kreuzung der Bruchverlängerungen mit der Abscherzone grenzt sich gegen eine starke Lineation normal zur Richtung der Lehne ab. Es wird vorgeschlagen, daß diese Strukturen als `vom Abbau verursachte dynamisch spröde Scherungen’ bezeichnet werden.

Jan 1, 2003

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by the Council. Although the worldwide readership of the Journal results in a preference for papers in English, the Council treats papers in Afrikaans on an equal basis, but, to meet the needs of the majority of readers, an English summary of some 5OO to 750 words should be provided.

Jan 1, 1984

By M. N. James

The Fracture Research Group has been operating at the University of the Witwatersrand for some ten years and, in that period, has achieved a significant profile, both nationally and internationally, through its research publications, industrially-based technical reports, continuing short courses in engineering education, and co1Jferences. This paper outlines the activities of the Group over the past few years, emphasizing the research thrusts and the results that have been obtained, as well as highlighting areas of current and future research interest The capabilities of the Group in terms of equipment and expertise are also discussed briefly.

Jan 1, 1995

By P. V. Scheers

A rotating-cylinder electrode (RCE) was used to simulate the effect of flow velocity on pipe corrosion. A comparison is made between the electrochemical measurements obtained and those measured with a laboratory-scale flow loop. There is good general agreement if the speed of rotation of the RCE is adjusted to give the same value of mass transfer Coefficient as in the other system. Hence, it appears that the RCE is well suited to simulate actual flow conditions in pipes. The simultaneous effect of flow velocity and pH value on the corrosion rate of mild steel in a synthetic mine water was investigated. The i1nrease of corrosion rate was found to be more pronounced at lower pH values and, apart from a sharp increase below pH 4, the initial corrosion rate also increased at pH 7 and 6.

Jan 1, 1992

By Donald J. Murdock

Column flotation has been developed over the past ten years as an alternative to conventional flotation. It has been used mainly in the cleaning applications of sulphide flotation, where its ability to wash the froth of entrained gangue and produce a higher-grade product has given it a distinct advantage over other technology. The benefits of column flotation can be summarized as follows: Improved concentrate gradeby 2 to 5 per cent . Significantly lower operating costs . Savings in capital investment . Superior control. Since the initial development of the equipment, a number of design improvements have been developed that now form the basis of the Cominco column-cell design. The purpose of this article is to discuss some of those design innovations, and present some typical industrial results.

Jan 1, 1991

By D. Mjonono, S. T. L. Harrison, N. Maliela, A. Kotsiopoulos

The improvement of coal waste management practices, through the co-disposal of waste rock with sulphur-lean fine waste tailings (<1 mm in size), can potentially mitigate acid rock drainage (ARD). On exposure to natural oxidants, the sulphide compounds present in mine discards generate acidity, creating a cyclical oxidation process intensified by iron and sulphur oxidising microorganisms. To inhibit the emergence of ARD, a stable mine dump may be constructed that is structurally stable and incompressible through the mixing of complementary waste fractions that reduce voids and access to acid generating surfaces. However, large voids manifest as scale increases, due to decreased particle interlock, enabling the unrestricted access of oxidants leading to the early onset of ARD. To avoid this phenomenon, enhanced packing approaches based on geochemical and geotechnical characterisation tests were employed to improve bed stability. These were assessed for long-term prevention using aggressive oxidative conditions typical of heap leaching applications. Favourable results were obtained for both blended and multi-layered systems. However, long-term success was most notable in beds with alternating layers of waste rock and fine waste tailings with co-mingled systems being more susceptible to failure. Deconstructed co-disposed beds provided valuable insight into post-leach structural transformations. Results indicated that relative changes in initial coarse discards to fine waste ratios were most notable in blended systems. Mass fractions of the comparatively more mobile fine wastes increased axially down these test columns that ultimately resulted in increased contact of oxidants with the acid generating waste discards. Conversely, more consistent ratios were observed in multi-layered configurations. In these systems, near impervious hardpans were created by the moisture retaining fine tailings, forming stable structures with neutralising barriers sustained at each alternating layer. Consistent with post-leach geotechnical characteristics, static acid-base accounting tests showed that the uppermost sections of blended systems were more susceptible to oxidation due to structural failure with fine particles migration, while the more stable multi-layered configuration evenly maintained neutralising capacity. Keywords: Acid rock drainage (ARD), bed structure, mobility of fine particles

Jan 1, 2020

By R. Koen, H. Visser, A. Roodt

"SynopsisThe tetraethylammonium salt of the mono-anionic coordination compound mer-oxidotrichlorido(thenoyltrifluoroacetylacetonato- K2O,O’)niobate(V) (NEt4)[NbOCl3](ttfa)], has been prepared under aerobic conditions and characterized by single-crystal X-ray diffraction. (NEt4)[NbOCl3](ttfa)] crystallized in the monoclinic P21/c space group, with a = 11.483 (5), b = 12.563 (5), c = 17.110(5) Å, and ß = 100.838 (5)o. The complex structure exists in a 50.0% (NbA) : 50.0% (NbB) positional disorder ratio.IntroductionComplexes containing organometallic type ß- diketone ligands with O,O and O,N donor atoms are used widely in coordination chemistry and have applications in catalysis, radiopharmaceuticals, etc. (Schutte et al., 2011; Roodt, Visser and Brink, 2011; Brink et al., 2010; Otto et al., 1998). These ligand systems are very useful because of their highly coordinative nature, high solubility, and also due to their ability to be functionalized with various substituents on the carbonyl carbon atoms (Schutte et al., 2011).Only a small number of ß-diketonate ligands have successfully been coordinated to a Nb(V) metal centre, with only a select few being characterized by X-ray crystallography (Viljoen, 2009; Bullen, Mason and Pauling, 1965; Preuss, Lamding and Mueller-Becker, 1994; Funk, 1934; Davies, Leedlam and Jones, 1999; Allen, 2002. The synthesis and crystal structure determination at room temperature of mer-oxidotrichlorido (thenoyltrifluoroacetylacetonato- k2O,O’)niobate(V) {(NEt4)[NbOCl3(ttfa)]} was first reported by Daran et al. in 1979. Accordingly, for this current investigation, (NEt4)[NbOCl3(ttfa)] was re-evaluated at 100 K to determine if the structural features might change with temperature."

Jan 1, 2015

By D. Farrow

Future development of kimberlite mines is now focused on mining at deeper levels. The consequences are increased difficulty and costs of the mining operations. The decisions on investments require accurate resource evaluation and quantification of the risk. In the decision process the first step consists in choosing the number of boreholes sampling the pipe relative to the level of uncertainty that can be accepted. The uncertainty in the volumes of rocks of different types can be assessed as soon as we can estimate these volumes from a given borehole layout and calculate the error by means of its variance for instance. In theory this can be achieved by using geostatistical techniques (‘transitive theory’), but in practice the calculation of the error on volumes can be achieved in very particular cases, assuming some regular sampling patterns. A different approach has been chosen based on simulations, giving maximum flexibility to reproduce the reality of the sampling procedure. The idea is to simulate the geometry of several ‘possible’ pipes with their internal geology and estimate them by kriging. Several experimental errors are obtained on which risk analysis can be performed. The aim is to find a feasible method to perform the simulations with reasonable chance to correctly represent the reality, without data on the pipe extension. The methodology applied is based on some hypotheses that can be assessed by the geologist as well as by the geostatistician. The procedure assumes a geological model based on current knowledge including appropriate geostatistical variation. What make these simulations specific and powerful in this case comes from the fact that the boundaries between the different rock-types can be simulated using a transformation of the real 3D space into a 2D space defined by means of polar coordinates. Ultimate transformations to account for smoother variations with morphological transformations allow the generation of realistic pipe geometries on which sampling pattern can be used to evaluate the estimation errors. By estimating the simulated pipe geometries with different boreholes layouts a risk curve expressing the uncertainty in the volumes of the different rock-types versus the number of holes can be developed.

Jan 1, 2003

By J. A. Venter, M. K. G. Vermaak, J. G. Bruwer

Electrostatic separation is employed in the concentration of zircon and rutile. The zircon concentrate undergoes an acid treatment to remove impurities from the surface of both the zircon and rutile. The purpose of the acid treatment is to increase the difference in the resistivities of the two minerals, thus ensuring the best possible electrostatic separation efficiencies. Previous test work suggested that these impurities are not removed, but only modified; the surface modification seemed more prevalent in the case of the rutile. The resistivity of the rutile changes with pH and thus the electrostatic separation of the rutile is influenced. X-ray photoelectron spectroscopy (XPS) indicates that there is an increase in the OH and adsorbed H2O concentrations on the rutile surface. XPS also showed significant differential charging on the rutile surface, which indicates that the species on the rutile surface have different resistivities. The zircon particles from the conducting and non-conducting streams have similar resistivities and no major differences in their surface species. Zircon losses during the final electrostatic separation appear not to be due to surface effects, but due to shielding of particles during the separation.

Jan 1, 2007

By C. Kelley

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings as fine as 75 microns and coarser have been used. In dry screening operations these same urethane screen surfaces have been relegated to only the coarser separation ranging from 1.0 mm and larger. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies, which allow an end user to consider urethane screen surfaces for dry screening operations where separations as fine as 75 microns are required. These technologies allow an end user to realize the inherent advantages of urethane in wear resistance while also realizing the benefits that a high open area urethane screen surface can bring. These benefits include non-blinding characteristics and feed capacities, which rival that of traditional stainless-steel woven wire mesh screen surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines in conjunction with which they are used. There will also be a presentation of several case studies of commercial installations where these technologies are utilized. These case studies are from the mineral sands industry; therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints, which must be taken into account when considering urethane screen surfaces such as temperature and chemical attack. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By G. Dellas, R. Mangera, A. Voigt

"X-ray transmission (XRT) sorting has become the preferred recovery technology option in several parts of the diamond-winning flow sheet. In the De Beers Group, applications of XRT are found across kimberlite, alluvial, and marine operations. This is the result of intensive R&D conducted over the years to arrive at a suite of machine embodiments capable of sorting and auditing diamonds across all size ranges.The first applications in the marine environment used the technology in an auditing mode, and served as a useful early predictor of diamond content weeks ahead of sorthouse returns. The same machines are now available with ejection capability to produce high final product grades. The next application was tests on coarse alluvial gravels as an alternative to dense medium separation. The results were very encouraging, and tests are planned for both green- and brownfield kimberlite environments, as well as to explore an alternative to conventional techniques in final diamond recovery. At the Jwaneng mine Large Diamond Pilot Plant (LDPP), the objective is to recover diamonds in the size fraction –45 +25 mm.The technical challenge remains in the finer sizes, for high-capacitymachines as direct alternatives to conventional diamond recovery technologies. This is an area of ongoing R&D and it is only a matter of time before the breakthrough emerges. X-ray transmission fundementalsXRT makes use of X-ray imaging techniques to analyse objects and materials, and has a wide range of applications from baggage scanning for security purposes (Martz et al., 2016), to recycling of waste material (Owada, 2014). During the last decade XRT has been applied to an increasing extent in the minerals processing industry (von Ketelhodt and Bergmann, 2010; Sasman, Deetlefs, and van der Westhuyzen, 2018). Dual-energy XRT (DE-XRT), in which images of the target material are obtained at both high and low Xray energies, allows for elemental analysis and therefore can be used to discriminate between various minerals.A DE-XRT system makes use of a dualenergy X-ray line scan sensor to generate images of transmitted X-rays (Figure 1). Dualenergy refers to the camera, which contains two sensors, one responding to low-energy Xrays and one to high-energy X-rays. Feed material can be imaged either while on the belt, or while in flight."

Feb 1, 2019

By Oaitse Medupe

The feed to the BCL concentrator is made of the ore from Phikwe No3 shaft, Selebi shaft and Selebi North shaft. The receiving bin of the concentrator has daily throughput of 7869mt live capacity of ore with feed grade from underground operation of 0.70%Ni, 0.75% Cu and 0.05% Co. The valuable minerals in the ore are Pentlandite, Chalcopyrite. Cobalt is present mainly in the solid solution in pentlandite. The common non-sulphides minerals are Amphibolites, quartz, micas, and Feldspar while pyrite and pyrrhotite are the major gangue sulphides. Pyrrhotite contains between 0.1% and 1% Ni in solid solution. From the mineralogical investigation, it was found that approximately 65% of the pentlandite in the ore occurs as exsolutions in the pyrrhotite and the grain sizes ranges from 8 to 38µm. about 25% of the nickel bearing pentlandite is medium grained and subhedral. This kind of pentlandite occurs along the cracks of pyrrhotite or as inclusions in pyrrhotite. The rest of pentlandite present is disseminated in the gangue matrix. Because of the fine occurrence of pentlandite, fine grinding was conducted in order to improve the recovery as well as the concentrate quality. A series of subsequent flotation test were performed in order to evaluate grinds of 35, 40, 45, 50, 60 and 80% passing 75µm. It was observed that ? The mass pull increased together with increasing fineness of grind ? Similar nickel recoveries were obtained at 35 and 40% passing 75µm but from 50% and 60% the grind was seen to adversely affect the nickel recovery. At 80% passing 75µm the recovery increased by small amount. ? Flotation kinetics showed higher initial nickel recoveries but these did not translate into higher final recoveries. ? Grinding finer than 80% passing 75µm yield very high grades of the concentrate in the first minute of the flotation test, and the grade is dramatically reduced in the fifth minute of the test. It was concluded that the current grind of approximately 48% passing 75µm is close to the optimum and no significant benefit were found to be associated with finer primary grinds. The inconsistence of the grade and recovery as well as the pentlandite losses will be discussed. Keywords: Pentlandite, Nickel losses, Grain size, Flotation

Jan 1, 2007

By L. A. Vermeulen, C. P. Campbell, D. D. Howat

The production 01material liner than 75 µm in a number of open-circuit mills was investigated. The mils ranged from laboratory rod and ball mils treating a variety 01 ores to large industrial rod mils treating gold and copper ores. It was shown that the dependence on feed rate 01 the production 01 material liner than 751J.1T1 can be accurately described by a simple formula that was derived in previous work. In some 01 the systems reviewed, it proved possible to assess the feed rate 01 ore to the mil at which the rate 01 production 01 material finer than 75 µm can be maximized.

Jan 1, 1991

By C. C. E. Pretorius, V. M. Mathoho, A. van Zyl, R. J. Mostert

The in-service degradation of the mechanical properties of steel components through the damage mechanism of high temperature hydrogen attack (HTHA), is a topic of concern in the refining and green hydrogen industry. This damage mechanism occurs in susceptible steels operating in environments at high temperatures and hydrogen pressures. The current investigation deals with the indirect monitoring of mechanical degradation via tracking of the swelling strain in affected structures. An autoclave with an AISI 316 shell was utilized to simulate accelerated HTHA damage at 550 °C and 46 bar for exposure times ranging from zero to 700 hours. The progress of the HTHA damage was tracked using encapsulated high-temperature strain gauges. The correlation between the swelling strain and mechanical property degradation was studied to develop a methodology for the continuous monitoring of embrittlement. The tensile sample orientation of the carbon steel plate was included as a variable, i.e., samples parallel, transverse, or perpendicular to the plate rolling direction were included, since it has been shown that the sample orientation influences the HTHA damage features. For the through-thickness orientation, and upon exceeding a threshold value of exposure time, all tensile properties were severely degraded, with values in the order of a 90 per cent reduction being observed. It was found that the degradation of carbon steel mechanical properties can be correlated to the swelling strain measured during exposure. The critical point for mechanical property degradation in the plate through-thickness orientation, whereafter a severe decrease in the ductility of the material occurs, was found to be in the order of 1% of the total swelling strain measured during exposure, equivalent to 65 microstrain. This threshold was found to be significantly lower than that expected from the literature, where limits of 400 to 1000 microstrain were postulated.

Nov 27, 2024