Search Documents

By J. P. Coetzee

Dr. K. Gebhard In his excellent and comprehensive survey on the future development of the Iron and Steel Industry in South Africa, Mr. Coetzee has also mentioned the direct reduction processes as a possible method of converting iron ore to iron. Mr. Coetzee has made it quite clear that at this stage one should not consider these processes as a 'magic formula' which herald a 'break through'. I agree entirely with this point of view. Once upon a time I held the opposite view, but in the meantime I have revised my views. To do so, I had 40 years at my disposal. In 1930 I had the privilege of being connected with the first commercial sponge iron plant in Germany1 - a plant which was capable of producing 40 tons of sponge iron a day. We were determined to prove that the blast furnace would become obsolete in the near future. We considered it as an unnecessary detour to convert iron ore first into an iron-carbon alloy, which contained further quite a number of undesirable elements, and to remove this carbon by an endothermic process. Direct iron-making seemed to be a logical short cut. Unfortunately, we were not able to establish this 'short cut,', but the life of our sponge iron plant was cut short. We had solved all technical but not the economic problems. Basically the positon is still the same today - mainly economic and to a lesser degree technological aspects determine the rate at which sponge iron plants are installed. More has been said and written than done about direct reduction plants. I think that there are two main reasons for this stagnation in the introduction of direct reduction processes. The first reason is that modern blast furnaces are just too good and too economic ever to be replaced by direct reduction processes on a large scale. This, of course, already limits the field of application for direct reduction plants. The second reason is that sponge iron production and utilisation is based on technical considerations, which increase not only the production cost of sponge iron but also the conversion cost to steel to such an extent that under special conditions only are direct reduction plants an economic proposition. Are these technical considerations still as forceful and valid today as they were when 'direct steelmaking' was first contemplated? The development of sponge iron production as a method of direct

Jan 3, 1971

By R. D. Cromarty, J. Du Toit

"Penetration of matte into tap-hole bricks causes detrimental refractory wear, which can lead to furnace breakouts. The ability of the tap-hole clay to form a protective layer on the brick, thereby limiting matte penetration was investigated by examining the interaction between platinum group metal (PGM) matte, tap-hole clay, and alumina-chrome refractory bricks on a laboratory scale.Samples containing clay and brick as well as samples containing clay, brick, and matte were heated to different temperatures to establish the clay-brick interaction and the extent of matte penetration. The greatest degree of physical contact between the brick and clay was achieved at curing temperatures of 600°C. Poor clay-brick contact was observed in the sample that was heated to 900°C.Matte displaced the clay in the clay-brick-matte sample that was heated to 1350°C, with significant matte penetration into the brick. Less matte penetration was observed when the clay-brick-matte sample was heated to 1500°C. Less matte penetration was also observed in the claybrick- matte sample in which the clay and brick were pre-baked at 800°C, and the sample then reacted with matte at 1350°C. IntroductionFloatation concentrate from ore from the eastern Bushveld Complex of South Africa, specifically the Platreef, Merensky, and UG2 reefs, forms the feed to the Polokwane platinum smelter (Hundermark, De Villiers, and Ndlovu, 2006). The ore from the UG2 Reef has a high chromite content, which requires high operating temperatures (1500–1700°C) to avoid chromium spinel build-up in the furnace hearth. These high operating temperatures lead to matte superheats in the vicinity of 500– 600°C, which put increased demands on the refractory materials (Nelson et al., 2005).Upon tapping, the matte moves through the tap-hole, which consists of an aluminachrome refractory brick-lined tapping channel (Hundermark, De Villiers, and Ndlovu, 2006). The flow of molten matte is stopped by the injection of tap-hole clay to form a plug in the tap-hole. The tap-hole clay hardens and strengthens during curing to obtain the required hardness and refractoriness against penetration, corrosion and erosion (Nelson and Hundermark, 2014)."

Jan 1, 2016

By J. A. Maree

After the South Deep complex was purchased by Goldfields in 2006a re-feasibility study was done and the life of mine (LOM) was extended to 52 years. This also implied that the mine?s infrastructure would have to be enhanced. One of the changes was the proposal of five new main orepass systems to be excavated before the mine reaches full production in 2013. Excavations started to show signs of scaling, and in some cases, whole new excavations were lost. This particular area was exposed to very high stresses and the geology was prone to body delimination rendering the relevant areas unstable. This paper investigates the conditions at the location of one of the proposed orepass systems, and the best possible orientation was suggested to ensure that the orepass system would be stable and have a practical life. It was, however, found that the fourth leg of the orepass system would require further support to be classified as stable by the chief rock engineer and the section geologist of South Deep. Several support methods and orepass system linings would then be analysed and evaluated to give calculated recommendations on how to productively and practically support an orepass system. Keywords Main orepass system, stresses, body delamination, impact and abrasion, rock support, concrete lining.

Jan 1, 2011

By A. O. Filmer

The techniques used in this study of the non-oxidative dissolution rates of high- and Iow-grade nickel mattes in hydrochloric acid involved leaching and the use of a rotating ring-disc electrode. It was found that the rate of metal dissolution depends on the potential at which the matte dissolves, a maximum rate of dissolution being observed at -0,2 V to 0,3 V (relative to a saturated calomel electrode). The results are comparable with those obtained in work on the dissolution of synthetic nickel and iron sulphides. The adverse effect of excess sulphur on the rate of nonoxidative dissolution is explained in terms of the mixed potential of the reaction. The leaching studies showed the feasibility of processing a high-grade nickel matte by non-oxidative dissolution, and indicate that maximum rates can be obtained in the presence of fairly Iow concentrations of oxidant. A relative selective dissolution of iron can be obtained from the Iow-grade matte under reducing conditions, thus resulting in a significant upgrading of this material. Letter to the Editor Dravo Corporation is seeking information concerning a special method of transporting explosives to aid in designing a large underground oil shale mine in the mountains of Colorado.

Jan 1, 1981

By R. Tabanrad

This article examines the stability analysis of intake tunnels of Karun III dam & power plant. The tunnels have been excavated with a 3-dimensional and fairly complicated geometry in Pabdeh weak formation rocks at Zagros region. Due to the particular excavation geometry and inapplicability of plane-strain status, the stability of these excavations has been analyzed using both the 3D elastic software Examine 3D and the 2D non-elastic software UDEC simultaneously. The geomechanical parameters have been estimated by back analyzing the measured displacements from instruments, which were installed in the tunnels, and the parameters have been used in non-elastic numerical model. The results of the analysis show that the strains occurred in surrounding rock mass are less than the allowable failure strain and that the tunnels are stable. In addition, considering the results of non-elastic 2D analysis, the areas with unstable potentiality were identified and after the instability occurred at the areas predicted by the model , it was stopped up to the allowable strain limit through installing additional support . Bei diesem Artikel handelt es sich um eine Analyse der Festigkeit der Eingangstunnel des Damms und Elektrizitätswerks “Karoon III”.Die Tunnel haben drei Dimensionen und eine sehr schwierige Form und sind in brüchigen Felsen in “Pabedeh ,in Zagrossgebirge”eingebohrt.Aufgrund besonderer Form der Bohrung wurde ihre Festigkeit durch elastische dreidimensionale Soft-ware analysiert,die gleichzeitig die drei-und zweidimensionale unelastische Soft-ware UDEC benutzt hat.Die geometrische Parameter sind mit Ausnützung der Analyse berechneter eingesetzter Versorgungen,die in Tunnel aufgebaut sind,bewertet.Und diese Parameter sind in Zahlen-Analyse benutzt.Die Ergebnisse dieser Analyse zeigen,dass die Drücke an Felsen weniger als problematischer Grad der Drücke sind und die Tunnel fest sind.Ausserdem wurde mit einem Einblick auf die Ergebnisse der unelastischen zweidimensionale Analyse die eventuellen unfesten Teile bestimmt.Nach entstandener Unfestigkeit an diesen Teilen wurde die problematischeDrücke für Aufbau mehrere Anlagen gestoppt. Cet article examine l'analyse de la stabilité de tunnels de la prise de Karoun barrage III et centrale électrique. Les tunnels ont été excavés avec une 3 dimensionnel et compliqué géométrie dans Pabedeh que la formation faible balance à région Zagros équitablement. Dû à la géométrie de l'excavation particulière et inapplicabilite de statut de tension plane, la stabilité de ces excavations a été analysée en utilisant les deux le 3D logiciel élastique Examen 3D et le 2D logiciel non - élastique UDEC simultanément. Les paramètres du geomechanical ont été estimés en analysant le déplacement mesuré d'instruments qui ont été installés dans les tunnels et les paramètres en arrière a été utilisé dans les modèles numériques non - élastique. Les résultats de l'analyse montrent que les tensions se sont produites dans masse du roc environnante est plus petit que la tension de l'échec admissible et que les tunnels sont stables. De plus, les régions avec potentialité instable ont été identifiées étant donné les résultats de 2D analyse non - élastique, et après que l'instabilité se soit produite aux régions prédites par le modèle, il a été arrêté jusqu'à la limite de la tension admissible à travers installer du support supplémentaire.

Jan 1, 2003

By D. J. Bosman

Rapid fouling of condenser tubes in underground refrigeration plants is a frequent occurrence. It leads to low heat transfer efficiencies, with consequent serious reduction in capacity and increase in the horse-power requirement of the units. High pressures develop in the condensers, and frequent cleaning of the tube bundles is required. The cleaning operation takes up to 8 hours and in some cases results in significant loss of production. One of the possible causes of fouling is deposition of scale, but this can be readily overcome by controlling the concentration of the water. When water evaporates, the dissolved solids remain behind; thus evaporation increases the amount of dissolved solids per unit volume. If half the original volume evaporates, the concentration of the dissolved solids is doubled and the water is said to have a 'concentration' of two. Concentration may be controlled by regulating the amount of water allowed to bleed from the system. The actual concentration value required is a function of the chemical analysis of the circulating cooling water. In one instance, where the problem of scale formation had been eliminated, fouling still persisted, and the possibility of excessive quantities of dust in the re-circulating water was investigated. A dispersing reagent was added to the condenser cooling water as a means of preventing sludge deposition in the condenser tubes. As shown by curve A in Fig. 1 the reagent addition did not decrease the rate of fouling.

On Friday, 18th April, 1986, Stefen Kenneth de Kok passed away peacefully at his home in Johannesburg after a short illness. New President of FSPE Mr R.G. (Bob) St Leger took office as President of The Federation of Societies of Professional Engineers on 1st July, 1986.

Jan 1, 1986

W. C. J. van Rensburg and D. A. Pretorius (H. Glen ed.). South Africa's strategic minerals - pieces on a continental chessboard. Johannesburg, Valiant Publishers, 1977. 170 pp. RI2,00. (Obtainable from The Librarian, Foreign Affairs Association, P.O. Box 26410, Arcadia, 0007 South Africa.) This book provides the answers to many questions relating to what minerals South Africa produces and in what quantities, what mineral industries and trade she practises, and what mineral resources and reserves she possesses.

Jan 1, 1978

By H. B. Prinsloo

Change management and training initiatives in remote rural settings in Africa are generally difficult to implement successfully due to factors such as varying levels of education, multiple nationalities and languages as well as cultures in one workplace. The challenge has always been the ability to implement change management and training initiatives that will have an impact despite these differences. Essentially this requires that the change and training interventions employed are applicable and should work well with a wide range of individuals sitting in one room ? in practice this can vary from semi-literate workers to engineers with PhDs. In this paper we will share the theory behind behaviour-based change management and training and present a case study that reviews an actual supply chain improvement and sustainability implementation at a Zambian copper mine. The case study explains the results achieved as well as the interventions employed to achieve these results in a multidimensional organizational environment. This paper is relevant to delegates who are faced with implementing changes or training in a similar mining environment. Keywords change management, behaviour-based training, learning style, P2P process.

Oct 1, 2013

By W. K. Brisden

The SAG Milling Seminar, which was held at Murdoch University in Perth on 30th November and 1st December, 1989, was a very successful technical seminar. Organizer Dr Norm Stockton reported a total attendance of 130, which was higher than the 70 expected: 20 delegates came from the eastern States and the remainder were from Western Australia.

Jan 1, 1990

By A. J. Burger, F. L. D. Cloete

Tests indicated that effective recovery of pyrite from a coarse Witwatersrand quartzitic ore can be accomplished by intensified flotation in an air-sparged hydrocyclone. Air is fed through the porous cylindrical wall of the hydrocyclone into a swirling layer of slury. Hydrophobic particles are attached selectively to small air bubbles, which form a froth and are recovered through the overflow. Hydrophilic particles pass out in the underflow. A spigot in which flow is restricted by an orifice was found to be more successful in preventing blockage by wood chips than an annular opening between a pedestal and the cylinder wall. Pyrite recoveries of 85 to 93 per cent at grades of 35 to 40 per cent sulphur were obtained in the air-sparged hydroclone with residence times of about 1 second. Comparative tests in a batch flotation cell after 320 seconds yielded average recoveries of up to 96 per cent, but with a mean grade of 32,5 per cent sulphur. A high colector dosage of 120 g/t was required in the cyclone, compared with the 40 gft used in conventional operations. An air flowrate of about 150 I/min was adequate at a slury feed rate of 35l/min. Particle sizes between 38 and 106µm yielded the best flotation results.

Jan 1, 1988

Visit to the Datsun Nissan Company's body pressing and assembly plant at Rosslyn, Pretoria, and the Claremont-Danville Tunnel on 27th February, 1970. The excursion arranged for the 27th February to the Datsun Nissan motor car assembly plant at Rosslyn, near Pretoria, in the morning and the Claremont-Danville tunnel in the afternoon was well supported by some 43 members. The visitors were met at the factory by Mr Rademeyer, the Industrial Relations Manager, and members of his staff and were taken to the artisan training centre for light refreshments. There is a well-equipped training section with an air-conditioned lecture hall; we were told that such training facilities were important because of the cosmopolitan nature of the artisan staff. The visitors were divided into small parties and taken to the tool die and jig-making section, which is perhaps the key department for a factory of this nature. There the many dies for the presses in the body pressing section, as well as the complicated jigs for body welding are made. The technique for making the castings for the dies is interesting. A polystyrene model of the casting is embedded in moulding sand. In a neighbouring foundry molten metal is pressed into the headers and burns away the polystyrene, which leaves no residue, and this exactly fills the space occupied by the model. This rough casting is then machined in large copying machines (costing as much as Rl80 000). An exact plastic model of the surface of the pressing required, set up in juxtaposition to this casting is traversed by a master stylus which operates the slave milling cutter, thereby machining the surface to close tolerances. The machined casting is cleaned up by hand and finally finished in large spotting machines, using a blue dye to show up high spots, to the fine degree of accuracy required. The body pressing section was next visited. There the large number of pressed parts which make up a vehicle body are pressed out of special deep drawing steel plate. Some of the largest presses were capable of applying a pressure of 1 200 tons and cost as much as Rl85 000 each. The visitors then followed through to the assembly section where jigs are used to hold together the many pressings, which are then spot welded into body frames. The frames go to an assembly line where they are finished to the stage for painting. The continuous crawl painting assembly line carries the frames through all the stages of prime coating with zinc phosphate sprayed on in a tunnel, followed by immersion of the lower parts in a priming bath, then drying and spray painting and baking in tunnels. The body frames, after painting, join another assembly line, where the doors, upholstery and many fittings are attached. After this stage the completed bodies are lowered onto and attached to the chassis units which are largely assembled from imported parts (engines, transmission units, etc.). From the end of the line the completed cars are driven off to the trial track and then pass through a tunnel with powerful water sprays to detect leaks in the body work. The proportion of locally made parts is just on 45 per cent. An interesting aspect of the assembly organization is that, of the 140 or 160 cars completed each day there may be included some of each of the Datsun model as well as some Renault and Alfa Romeo models models which are assembled by this company. The change from one model to another several times a day does not present any difficulty to the organization. Each section of the assembly plant 'buys' the units from the preceeding section and 'sells' to the succeeding section. This means that the responsibility of each section ends when the unit is sold to the next section. The cost of repairing any faults found subsequently is charged to the section where it is found, which puts a powerful emphasis on meticulous inspections between sections to safeguard their costs. After the tour the parties assembled at the lecture hall where a lavish cold buffet luncheon was provided by the company. After luncheon Mr A. R. C. Fowler, on behalf of the Institute, thanked the Managing Director, Mr W. J. Wilson and his staff for this most interesting and well organized visit. The party then left for the Claremont-Danville tunnel. The tunnel is being driven by General Mining Federale Kontrakteurs through the Daspoort Range, Pretoria, to link the suburbs of Danville, near Iscor, and Claremont, which at present can only be reached by a nine mile detour. It is estimated that some 6000 vehicles per day will use the tunnel. Before entering the tunnel a short talk was given by Mr Ross who is in charge of operations. He called on various officials and staff of the Consulting Engineering firm, Basil Read (Pty.) Ltd., to describe the tunnel and

By J. van der Merwe, C. Phetolo, V. Matjeke

The mechanical properties and microstructure of AlSi10Mg alloy samples that were printed by selective laser melting (SLM) were studied to determine the effect of processing parameters and building orientation. After printing, the alloy was stress relieved at 250°C for 2 hours. The microstructures were analysed by optical microscopy and scanning electron microscopy (SEM) to determine the alloy phases and distribution. Phase transformation characteristics of the material were evaluated using differential scanning calorimetry (DSC). Mechanical properties were determined by subjecting the XY- and Z-built samples to tensile and nano-indentation testing. The samples from the tensile tests were then used to perform fractographic analysis by SEM. The microstructural properties in each orientation revealed a non-homogeneous microstructure which was characterized by a semi-elliptical tract and fine silicon precipitates, which were found to be softer along the fusion zone. The DSC thermograms revealed that the material underwent two phase transformations during the first heating cycle. The mechanical properties revealed a higher UTS, higher yield strength, and a lower percentage elongation in the Z orientation than in the XY orientation. Fractographic analysis showed that crack initiation in both orientations started from the surface in a brittle manner due to surface flows, and then propagated via microvoid coalescence.

Jul 1, 2021

By Sh. Arshadnejad

Stress analysis in a rock medium is essential to determine the stress concentration between two consecutive circular holes and prediction of fracture behaviour. When two consecutive circular holes in a hard rock medium such as granite are loaded internally by the pressure of non-explosive expansion material (NEEM), stress concentration occurs between the holes which then causes the rock to fracture. In this work, finite element (FE) analysis using Phase2 code was employed to study the stress concentration between two consecutive circular holes under internal pressure induced by NEEM. Effects of different hole diameters and spacings, rock properties and NEEM pressures have been analysed. The data gained from the numerical analysis and analytical solutions were then used to develop two models. These models were then modified by using the FE data and polynomial regression analysis. The developed analytical models showed to be in a very good agreement with the FE analysis. Hence, the developed models can be used with confidence to determine stress distribution and concentration factors around two consecutive circular holes in a hard and brittle rock which are loaded internally by the pressure induced from the NEEM. Keywords Finite element method, non-explosive, quarry mining, stress concentration..

Jan 1, 2011

A Seminar to discuss 'Reactivity of Line in Steel Making' was held in the auditorium of Iscor's Headquarters Building in Pretoria on the 5th August, 1971. The Institute organised this Seminar on the occasion of the visit of Dr Obst of the Rheinische Kalkstein Werke GMBH, Wuelfrath, West Germany. The latter is one of the largest lime companies in the world and Dr Obst is in charge of their research laboratory. He and his co-workers have earned a reputation for their research into reactivity of lime in steel making. This work is also of great importance to the steel industry in this country, particularly with the changes which are occurring with the introduction of basic oxygen furnaces. Some 80 persons representing most of the major steel companies attended this Seminar. Dr Obst presented his most interesting paper which he illustrated with projector slides. This paper is printed in full in this journal. This was followed by several contributions and active discussions. The first contribution was made by Dr T. B. Beeton of the Research and Development Department, Iscor. He gave a brief summary of the studies on reactive lime carried out at Iscor since 1968. Their work was particularly related to the selection and definition of the various reactivity tests and the correlation of these with plant results. He demonstrated that the DIN methods, particularly the Din (40°) test, gave the best results and reported that good agreement had been reached between Iscor, Highveld and Northern Lime on future test procedures. Mr B. Lowther of The Northern Lime Company then dealt with problems associated with the production of high reactive lime. The rotary kilns at The Northern Lime plant at Lime Acres are particularly suitable for the production of high-reactive lime, because this type of kiln lends itself to accurate control of temperatures and retention times. Several problems, however, exist. Because of the long haul distances and the deterioration of reactive lime by absorption of CO2 and water, high reactive lime is not suitable for most customers. To constantly be changing kiln conditions to produce relatively small quantities of high-reactive lime, therefore, causes problems. Highveld Steel at present is the only company requiring high-reactive lime and a satisfactory product is now being produced at a cost because kiln capacity is reduced and fuel costs are higher. Dr P. R. Jochens, of the National Institute for Metallurgy then submitted data to show how the reactivity of soft burnt reactive lime deteriorated due to long railage hauls. Detailed sampling of trucks had been carried out leaving the lime works and on receipt at Highveld and it was demonstrated that there was deterioration in the top layers of the truck. This top layer protected the balance of the lime which is still in good condition on arrival at Highveld. Exposure to atmosphere by further handling and storage into the bunkers at Highveld, however, resulted in further severe deterioration in the lime reactivity and the lime when finally fed to the Basic Oxygen Furnace is reduced to one third to one quarter of the original reactivity value. The same deterioration does not occur with normal run of kiln lime, which is burnt harder, but still has a satisfactory reactivity for most purposes. Mr A. A. Hejja of the Department of Metallurgy, Witwatersrand University then made a contribution on the metallurgical aspects of the use of lime of different reactivities in the Basic Oxygen Furnace and the effect on desulphurization efficiencies. He gave a wealth of data on actual tests which had been carried out and came up with the surprising conclusion that the deterioration of high-reactive lime due to transport did not have as serious an effect on the efficiency of desulphurization as one would have expected. The efficiency was good provided high-reactive lime in the first instance had been produced, irrespective of whether it had deteriorated thereafter. Poor efficiency was obtained only when the lime in the first instance was produced in an unreactive form. The temperature rise in the Basic Oxygen Furnace also has a definite effect. If lime is introduced when the temperature is too high, soft burnt reactive lime becomes hard burnt and unreactive before it can dissolve in the slag. Use of ferromanganese slag assists dissolution of lime. There was a great deal of discussion following these contributions. Particular interest was expres8ed in the special lime described by Dr Obst. This consists of a mixture of fine lime which is premixed with fluxes and either briquetted or pelletised. The question of injecting finely ground lime as an alternative was also discussed. Both these systems eliminate the necessity for highly reactive lime. With smaller lime particles, larger surfaces are exposed thereby ensuring more rapid dissolution in the molten slag. The discussions generally were lively and informative and all present derived benefit from learning of the experiences of others. The valuable contribution made by our German visitor, Dr Obst, was particularly appreciated. The instantaneous English-German translation service which was provided, greatly facilitated discussions.

By N. C. Joughin

A simplified economic model is derived for the financial return from a new gold mining project. The model is used to analyze the effects of changes in the mining rate, capital costs, working costs, value of the reef and the stoping width. The most effective avenues for improving the return from a new project are indicated. It is shown that those technological innovations which would improve the return significantly, and therefore make it possible to open more mines, are the use of smaller mines, means for improving the mining rate to capital costs ratio for smaller mines, planning and control of mines by computer simulation, an improved mine valuation procedure and means for mining at a decreased stope tramming width.

Jan 1, 2014

By D. Wines

"Slope stability analyses have traditionally been undertaken in two dimensions assuming plane strain conditions. Although three-dimensional analysis techniques are widely available and used routinely for open pits, two-dimensional analyses are still more common due to the relative ease of model construction and the relatively rapid simulation times.Two-dimensional analyses will often produce different results to three-dimensional analyses for the same slope. It is generally thought that two-dimensional analyses will produce more conservative results. The main reason for the differences is the ability of three-dimensional analyses to account for the three-dimensional nature of the various model inputs, including the slope geometry, the distribution of soil and rock mass domains, the orientation of geological structures with respect to the excavation face, the orientation of the in situ stresses, and the distribution of pore pressure. In some cases, for a long, straight slope in basic geological conditions, two-dimensional analyses can provide a reasonable representation of the problem. However, in many cases, the inability of a two-dimensional analysis to represent the true three-dimensional nature of the problem will lead to unrealistic analysis results.This paper discusses the reasons, as detailed above, for the differences in two-dimensional and three-dimensional analysis results. Work by others is summarized, and additional numerical analyses are performed to provide an improved understanding of the effects of slope geometry, structural orientations, and in situ stresses on predicted stability. Case studies are presented for both stable and unstable slopes, and the behaviour of these slopes is related to the three-dimensional nature of the slope geometry and geology.The previous work, the new analyses performed here, and the case studies show that it is often important to provide a realistic representation of the slope in three dimensions in order to obtain reasonable stability analysis results. This is particularly true for hard rock environments where structurally controlled failure mechanisms are most likely. The paper also highlights the fact that back-analysed properties obtained from one analysis technique are not necessarily applicable to forward analyses using another technique."

Jan 1, 2016

By S. M. H. Ahmadi, K. Barani, F. Moradpouri, R. Ghaedrahmati

As exploration is time-consuming, costly, and risky, determination of the erosion surface of a metalliferous deposit before geophysical surveying and exploration drilling might be very helpful. Geochemical haloes can be used to determine whether the erosion surface is supra-ore or sub-ore and thus reduce the risk of exploration operations. The aim of this investigation is to determine the erosion surface of the North ROK porphyry deposit (NRPD) in northwestern British Columbia in Canada using linear productivity (LP), which is the content of an element defining the halo multiplied by the width of the halo. A total of 2045 soil samples from the B horizon were analysed using ICP-MS for 36 elements, including Cu, Mo, Pb, Zn, Au, As, Ag, Ni, Co, Fe, and Mn. The data-set was snalysed to obtain the statistical parameters and the elements Cu, Mo, Pb, and Zn were chosen to calculate the linear productivity and the total linear productivity. These four elements were modelled using probability plots to identify and separate subpopulations in terms of anomalous haloes and background, including the threshold values of each subpopulation. The results of the probability plot modelling and thresholds values were then used to map the distribution of each element in a GIS to calculate the linear productivity. The total linear productivity indicated that the erosion surface is supra-ore. Finally, a 3D orebody model of the Cu, Mo, Pb, and Zn distributions was constructed using borehole data and used to validate the results.

Feb 6, 2023

R. C. J. Goode (President): South Africa is known for its sunshine and mineral deposits-especially its gold and its diamonds-and as this year marks the 75th Anniversary of the establishment of the South African Institute of Mining and Metallurgy, it is appropriate that I say a few words about mining and metallurgy and the part this industry and our Institute has played in the life of this country. Africa, as the Dark Continent, with its fascinating tales of Prester John, Ophir, Queen of Sheba and its myths and legends has throughout the ages fired the public imagination. Pharaoh Necho, 600 years before the birth of Christ, sent an expedition from Egypt around the Cape to probe this strange land. The gold for King Solomon's throne was said to come from Monomotapa-the country now known as Rhodesia. Centuries later the Arabs and Portuguese searched for this mineral wealth. The Arabs found little gold but unfortunately established a lucrative trade in black slaves. Now let us take a brief look into the closing stages of the Stone Age when the indigenous population of the lower portion of this continent consisted of the Bushmen, a nomadic hunting people who knew no metals and kept no stock, and the Hottentots who were a pastoral folk with cattle and sheep. Then somewhere about the 11th century the Bantu started their long migration southwards and brought with them the knowledge of smelting of iron ore. One of their settlements was here in Johannesburg on the Melville Kopje at Emmarentia. These people were the first miners and metallurgists on the Witwatersrand and the beautifully preserved iron smelting furnace constructed nearly 1,000 years ago is a tribute to their technical ability. This ability to use iron to make better spears for hunting or to fashion hoes for cultivating the soil led to their establishment as a superior tribe. The earlier Bushmen were pushed back to the inhospitable swamps and deserts and the Hottentots fled to the south. The Bantu also knew the art of copper smelting. In the days of the Dutch East India Company, at the end of the seventeenth century, Bantu workers brought copper from the north-west Cape to Simon van der Stel, but it was another two hundred years before the white man turned this to advantage. Stories of the Bantu mining gold spurred the early European hunters to travel deeper into the heart of Africa in search of wealth, and we are told that Karel Kruger, in 1834 whilst leading an ivory hunting expedition, discovered gold on the Witwatersrand, and took samples to Cape Town; but when he returned with a larger expedition a few years later his party was attacked by Moselekatze's Matabele near Potchefstroom. Kruger was killed and only the legend survived. The real spur to mining in this country was the discovery of diamonds in Griqualand West in 1867. The field seemed fabulously rich and diggers flocked to the scene from the four corners of the earth. With them came Cecil Rhodes, Barnato, Beit and some of the finest mining and financial brains the country had yet seen. These giant entrepreneurs were not tempted by the small deposits of gold in the Barberton and Pilgrim's Rest areas when these were made a few years later but

By E. G. Galvez, E. Mate, L. A. Cisternas, C. Cruz, L. Cortés, M. E. Osorio

Designing and optimising flotation circuits are critical for mineral beneficiation plants, and therefore several procedures have been published. The modelling of flotation circuits with the objective of design and optimisation is problematic in that different approaches are used for the modelling of flotation units and regrinding units. Usually, regrinding models are based on particles characterised by their size, while flotation models are based on species characterised by fast and slow classes. The relationship between particle size and liberation can be used, but it requires laboratory studies that are time-consuming and costs are high. It is therefore not surprising that few studies on flotation circuit design and optimisation include flotation units and regrinding units simultaneously. In this paper, it is proposed to model the regrinding stage using species characterised by fine-slow, medium-fast, and coarse-slow flotation species. In deep, the regrinding model is derived from a population balance approach based on flotation species. The fraction of these species at the feed and product of the grinding unit is determined by flotation tests. Then, based on these data, the model parameters can be determined by a regression estimation procedure. A local ore was used to validate the model. Keywords: Modelling, flotation circuit, grinding circuit, process design

Jan 1, 2020