Search Documents

By H. Wagner

The paper points out that bord-and-pillar mining is the most important method of coal extraction in South African underground coal mines, and advocates that pillar design procedures should be refined to make more rational allowance for the differences in strength properties between various coal seams and roof and floor strata. However, any deviations from well-established design procedures must be based on sound engineering principles and reliable data on the strength properties of the seams and strata concerned. Recent information indicates that practices for the protection of surface structures against underground mining should be revised.

Jan 1, 1980

By R. T. White, A. Higginson, M. Phil

Samples of water that had been collected underground from eight gold mines in South Africa were subjected comprehensive analysis of the quality of the waters, and their corrosivity on mild steel was measured by the laboratory techniques of extrapolation from Tafel plots and of polarization resistance. The results indicate that, if such factors as pH, Langelier index, and degree of aeration are beyond certain specified limits, the corrosivity ofthe water is affected. The applicability of the corrosivity index in predictions ofthe degree corrosion is questioned. Suggestions are included for future work involving the fundamental characterization of the corrosivity of mine waters.

Jan 1, 1983

By W. K. Brinsden

The Australian Institute of Geoscientists (AIG) held their fifth successive annual seminar at Observation City, Scarborough, in Perth on 15th November, 1990. The title of the seminar was 'Strategies for Grade Control'. The Seminar attracted 158 delegates, including 10 speakers. In addition to geoscientists, the attendees included mining engineers, metallurgists, and mining analysts. The welcoming address was given by Rob Duncan, Chairman of the Westem Australian Branch of AIG, who said there is a strong demand for this type of seminar in Western Australia (WA). It helps geoscientists to keep up with former colleagues and to keep abreast of technical developments.

Jan 1, 1991

By C. Musingwini, M. Woodhall

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility, mainly due to its nebulous nature. If one glosses over technical operating flexibility the resultant mine layouts and schedules tend to be sub-optimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. This paper illustrates the nature of technical operating flexibility, reviews previous work on valuing operating flexibility and proposes how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility is quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility, ore availability.

By L. Dison

This technical note is issued in two parts as follows. Part I, which appeared in the January issue of this Journal, after a brief introduction, discusses the value of patents and the law of patents, including patent applications and the exploitation of inventions. This is followed by some comments for the benefit of would-be inventors and potential users of patents. Part I focuses on the mining industry and then discusses views on patents that were quoted in Part I. The last section makes recommendations as to how inventors and users (including mining authorities) should handle patents.

Jan 1, 1992

For many of us, formal academic education slows abruptly when we leave a tertiary institute of learning. We start applying and connecting newly acquired knowledge with the practicalities of a career, and begin to think in a manner that is technology-oriented. Subsequent vocational advancement is offered by the .many mining and professional journals that circulate through departments, and by conferences and schools that are organized in-house and via the SAIMM and other professional institutions. The importance of these schools cannot be overstated: they combine people and developing technology to the benefit of the industry as a whole.

Jan 1, 1992

By D. F. Malan

This study Investigates transient closure piles of tabular excavations. Measured closure profiles in stopes indicate that time-dependent acts f the rockmass can be very prominent but such effects have been largely neglected in past analyses and modelling. This was due to a poor understanding of the time-dependent mechanisms controlling closure rates This paper investigates the feas-ibility of representing the rockmass as a visco-elastic medium. Currently, no analytical solution for the viscoelastic convergence of a tabular stope is available in the literature. Therefore, the author derived a solution using the correspondence principle and a known elastic solution. It is assumed that the rockmass behaves elastically in hydrostatic compression and as a Kelvin substance in distortion A parametric study is Included to aid in the calibration of the model parameters, together with a discussion on the correct calibration of these parameters from experimental data.

Jan 1, 1995

By J. A. L. Napier

The application of excess shear stress as an aid to the design of mine layout is reviewed, and the critical parameters required to describe slip on a plane of weakness are noted. A design procedure that is required to model the cyclic build-up of excess shear stress is described. A number of simple examples of mine layouts on two reef planes intersecting a fault plane are then considered to illustrate the application of the design concept and to highlight some of the pitfals that may be encountered

Jan 1, 1987

By K. Bryan, O&apos

A 10-year program to integrate crushing and screening models into daily flowsheet design practice has proven successful. A Circuit Analysis Program (CAP) is used worldwide to design and evaluate new and existing crushing flowsheets. To gain user acceptance of CAP and maximize effectiveness, model development, simulation flexibility, ease of use, and developing international access are key issues. These issues have been resolved effectively resulting in flowsheet simulations to assist in justifying increased capital investment. CAP is presently utilized in Canada, United States, and South Africa with intentions to expand to Europe and Asia.

Jan 1, 1987

By A. R. L. Thoresson, S. J. Lennon, F. P. A. Robinson

This paper reports and discusses experimental work carried out on heavy nickel-electroplated turbine-disc steel. Mechanical and fatigue tests were used to determine whether the coating was suitable for turbine-disc applications. It was concluded that dehydrogenation treatment is necessary in order to produce compatibility of the coating and substrate

Jan 1, 1988

By P. H. Botha

An account is given of the procedures used by the South African Iron and Steel Industrial Corporation (Iscor) for tests on the flotation of coal fines, and some of the beneficiation problems encountered with coal from Durnacol, Grootegeluk, and the Soutpansberg area are discussed. These, and other South African coals differ from overseas coals in that they contain a high percentage of fixed ash, which means that they have to be crushed more finely for liberation and that they then contain more fine material (smaller than 0,84 mm). In addition, the coal from the three areas mentioned occurs in fine layers and seams, and contains many intergrown particles.

Jan 1, 1980

By R. K. Brummer

The support of stopes and tunnels in South African gold mines subject to rockburst damage requires special attention. The interaction of a seismic wave with either a stope or a tunnel is subject to a number of variables, namely the distance from the source of the event, the ground velocity, the orientation of the excavation with respect to the direction of the seismic wave, and the geology and fracturing around the excavation. This paper discusses these factors in relation to the support requirements in stopes and tunnels. The need for the integration of hydraulic props with stope support and the use of yielding anchors for tunnel support are emphasized.

Jan 1, 1988

By J. S. Freer

Integrated Environmental Management (IEM) involves the integration of environmental factors Into project planning, execution, and operation from inception to final closure and after-care. The objective IS to develop the most cost effective, environmentally acceptable manner in which the project can proceed, and to gain the approval of the authorities and the support of the interested and affected parties (I & APs) for the benefit of the developer, the economy, the people of South Africa and the environment on which they depend.

Jan 1, 1993

By J. L. Taylor

The belt-filtration plant at Chemwes Limited has been in operation for three years. The plant design is discussed. Operational and engineering problem areas are reported, and where possible the modifications or practices that led to their solution are mentioned. Capital and operating costs, together with selected general operating data, are also included.

Jan 1, 1983

By J. H. Selby

The Southern African Institute of Mining and Metallurgy hosted the 6thInternational Heavy Minerals Conference at the Zulu Nyala Game Lodge near Hluhluwe in Zululand, during September 2007. This series of conferences has run for 10 years and has been held on three continents. The interest that has been shown in the conference over the years has demonstrated that the field of heavy minerals is a dynamic and profitable one. It is perhaps appropriate that the tenth conference was held in Zululand, South Africa, where it had its roots. The conference theme was ?back to basics?, and this implied revisiting many of the technologies that made this industry a great one. In doing so, we got a view of how those basic technologies have been put to new applications. There were 39papers accepted for the conference, covering all aspects of the industry. These were presented over a period of four days. This edition of the Conference Proceedings provides the reader with a permanent record of these papers. We hope this volume will join the other five, which this series of conferences has produced, and give a lasting record of the development of our industry.

Jan 1, 2007

Visit to Premier (Transvaal) Diamond Mining Company Limited On the 14th February, 1973, 44 members of the Institute were the guests of Premier (Transvaal) Diamond Mining Company Limited. Metrication News PRESSURE GAUGES There appears to be doubt in some circles about the general acceptance of the pascal (Pa) as a unit of pressure and stress. NATIONAL INSTITUTE FOR METALLURGY / NASIONALE INSTITUUT VIR METALLURGIE REPORT. VERSLAG No. 1430 THE USE OF THE EKCO MINERAL ANALYSER FOR THE DETERMINATION OF COPPER AND ZINC IN THE PRESENCE OF IRON 27th June, 1972 Investigator: Gisela Domel SYNOPSIS The Ekco Mineral Analyser-a portable, radio-isotopic X-rayfluorescence instrument-is briefly described,

By W. J. C. Pothas

This paper describes the state of the art in backfilling techniques used on East Driefontein Gold Mine. Areas covered are the preparation plant, the distribution plant, the pipeline network and finally placement techniques. The in-situ performance of placed backfill has been assessed by the Chamber of Mines Research Organization, and results to date will be shared. Details of the backfill expansion programme that will enable this facility to be made available to all working places are included. Benefits obtained by the introduction of backfilling are described, together with certain management aspects to be considered in the control of quality and quantity of support supplied via a pipeline.

Jan 1, 1988

An evaluation was made of the wear and performance characteristics of liter bars, and the cost-life effectiveness of backing materials for rotary-mil liners. In a large run-of-mine mil in which the liter bars were mounted on grid liners of austenitic manganese steel (AMS), the liners had an average life that was five to six times that of equivalent unprotected liners. For a single mil, this is equivalent to annual savings in the cost of materials of up to R320 000, and to a downtime of 100 hours. Of the five materials tested in a large pebble mil grinding quartzitic ore, AMS grids and 'white iron' blocks performed best on a cost-life basis, with possibly improved performance from a real white cast iron. (The 'white iron' was shown by microstructural analysis to contain flake raphite and pearlite, being in reality a grey cast iron.) The high-chromium white iron had by far the longest predicted life, with mild steel a surprising second. Rubber was shown to last well in this type of mil. The wear rates of liners change during their lifetimes. The protective effect of liter bars was clearly illustrated by the reduction of over 40 per cent in the wear rates of the liners when the lifter bars were renewed to a height of 80 mm from a fully worn height of 35 mm.

Jan 1, 1991

In the investigation described here, it was found that the main effect of temperature is on the rate of flotation, and that adsorption of the reagent is not rate controlling. Above 10°C, the flotation rate of pyrite and gangue increases almost exponentially with a rise in temperature. Below that temperature, the flotation rate of pyrite shows a sudden marked decrease, that of gangue increases, and the sulphur grades are significantly poorer. In the flotation of pyrite, the mass transfer of the pyrite from the pulp to the troth is thought to be the ratecontrolling step, whereas the flotation of gangue is controlled by the combined effect of the stability and velocity of the froth and the viscosity of the elutriating medium. The latter is probably the controlling effect at temperatures below 10°C. Little difference was noted in the recoveries (provided no time limit was set) with changes in temperature; hence adequate recoveries can be obtained at Iow temperatures by the introduction of longer residence times for the pulp. The adverse effects of Iow temperatures on grades can be overcome only by additional cleaning or by heating of the pulp.

Jan 1, 1984

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988