Search Documents

By J. M. Czaplicki

The problems connected with deep mine hoisting and the increasing complexity of this process can be analysed through the application of such mathematical tools as stochastic modelling to study the effectiveness, reliability or safety of hoist methods. To relate these theoretical investigations to real practice, knowledge about components, their stochastic nature and stochastic order of appearance is necessary. This paper presents results obtained during the ten-year (1976-85) period of research undertaken in the Polish mining industry by the Mining Mechanisation Institute of the Silesian Technical University, Gliwice, Poland.

Jan 1, 1987

By O. Fenn

Earlier work had shown that the use of water jets at moderate pressure enhances mechanical cutting in hard rock. To assess the potential of this technique for use in conjunction with free-rolling cutters, a series of laboratory tests was conducted with disc and button cutters to determine the effect of variations in the jet and cutting parameters on the cuter performance. In these tests it was found that the use of water jets at pressure in the range 5 to 40 MPa can reduce the forces on a free-rolling cuter by 40 per cent, which represents a significant improvement in cutting performance. The reduction in thrust force was found to be dependent on jet pressure: the greater the pressure, the greater the reduction. The reduction in rolling force was independent of jet pressure over the range investigated. The results indicate that no additional improvements in cutting performance of any significance are to be gained by an increase in jet pressure above 40 MPa. The most effective jet configuration for the reduction of cuter forces was found to be four coherent water jets, two lateraly disposed on each side of the cuter and directed at the arc of contact between the cutting edge and the rock.

Jan 1, 1987

By G. Pienaar

The South African Institute of Mining and Metallurgy held a Colloquium on High-strength Low-alloy Steels on 27th October, 1983, at the Vaal Triangle Technikon, Vanderbijlpark. The Colloquium was attended by some 170 delegates.

Jan 1, 1984

By B. Rohrmann

The paper deals briefly with the history of vanadium, and its uses, price movement, and world resources. It then describes the titanomagnetite ore of the Bushveld Complex, and the production of vanadium from this ore at Highveld Steel & Vanadium Corporation Limited, giving details of the various processes used, including the roast-leach, rotary-kiln, electric-smelting, shaking-ladle, and basic-oxygen-furnace operations. The paper concludes with a very brief account of the treatment of Highveld slags in Europe for the production of vanadium pentoxlde and ferrovanadium.

Jan 1, 1985

By A. G. W. Knock

Logistic curves are used in the prediction of the primary production of tin metal from estimated worldwide resources. Such curves are asymptotic to the total cumulative reserves, which are a function of prevailing metal prices and total resources. The figures for tin resources are based on the findings of Robertson and of Brobst and Pratt, the latter authors including estimates of undiscovered deposits. It is suggested that tin production will slump from the present level to 100000 long tons per annum by the end of the century, but will reach a new peak of 200 000 long tons some thirty years later. It appears that production will never exceed 300000 long tons per annum unless substantial new resources, excluding those predicted, are discovered.

Jan 1, 1979

By G. P. L. van der Linde

EVERY OREBODY IS UNIQUE [ ] GEOLOGY AND MINERALIZATION DIFFERENT [ ]

Jan 1, 2005

By L. Woollacott, R. P. King

This paper presents data collected from full-scale plants in order to verify the predictions of a new simulator of CIP or CL operations. Good agreement was found between the experimental data and the simulator predictions. The simulator is able to predict the effects of many of the complex operating phenomena in GIP and CL plants that previous simulation techniques could not describe. This is illustrated by predictions of how factors, such as the manner of carbon transfer, concurrent leaching, and gold loading on eluted carbon, can affect the performance of an adsorption plant.

Jan 1, 1990

By M. W. Hildyard, J. A. L. Napier

The improved design of support systems and stoping strategies when changes in depth, stratigraphy, or mine layouts are considered must rely on the designer's fundamental understanding of the deformation mechanisms adjacent to underground openings so that he can extrapolate and predict expected mining conditions. This paper presents a numerical approach to the modeling of the growth and interaction of mining-induced fractures near the edges of deep tabular excavations in brittle rock. Fractures are represented by displacement-discontinuity elements that are allowed to propagate according to prescribed growth rules. This procedure is justified by the reproduction of several features observed in laboratory simulations of fracturing around openings in blocks of rock subjected to uniaxial and biaxial compression. An attempt is then made to explain some of the attributes of the fracture zone surrounding tabular stopes. Particular questions of interest are the sequence in which fractures form and are mobilized in front of the mining face, the effect of parting planes parallel to the plane of the excavation, and the distribution of stress parallel to the hangingwall and footwall.

Jan 1, 1992

By A. M. Sage

This paper reviews the metallurgical functions of vanadium in high-strength Iow-alloy steels, and discusses the ways in which vanadium is used in various types of steel supplied as reinforcing bars, plates, sections, and strip. Potential developments to meet new engineering requirements are discussed briefly.

Jan 1, 1984

By G. J. C. Young

The new metallurgical plant has a simple, compact layout, being designed for a small team of operators. The reasons for building the new plant are given, and its various sections are briefly described. These include the conveyor plant, milling plant (for run-of-mine milling), thickener plant, agitator plant, filtration, clarification, smelthouse, and central core joining the mill and filtration sections.

Jan 1, 1978

By M. H. Marsden, R. A. Laybourne, J. D. Flint

Operations of the strip mine at Arnot Colliery are described, and the improved volumetric extraction of the in situ coal reserves that has been obtained by the application of strip-mining techniques is highlighted. An account is given of the major problems encountered during the early stages of the operation with particular reference to overburden removal. coal and parting handling, and transportation. The techniques used in dealing with the problems and the current degree of success in overcoming them are outlined.

Jan 1, 1980

By G. V. R. Landman

Changes in the explosion behaviour of mixtures of coal dust, methane, and air when exposed to different energy sources are discussed. Changes to the lower explosive limits, minimum ignition energies, and rates of pressure rise when the same hybrid mixture of coal dust, methane, and air is exposed to ignition sources which are either spatially extended or spatially concentrated, are examined. A diagram is presented from which coal-dust loadings and methane presence can be determined which are below the lower explosible limits, and stated as a safety factor.

Jan 1, 1995

Members are advised that the Council has decided to change the format of the Journal from the present size to the standard international A4 size with effect from August, 1969. By making this change we will be conforming to more general practice today in regard to publications and this should effect certain economies and facilitate selling of advertising space. It has been arranged that in future the publication of the Journal, including advertisement sales, will be handled by Kelvin Publications (Pty.) Ltd. who are already doing this work satisfactorily for the Mechanical and Electrical Institutes. While making these changes, the opportunity is taken of redesigning the outer cover of the Journal to incorporate the new coat of arms. The Council trusts that these changes will meet with the approval of members.

Iron ore pellets with or without additives are commonly used as alternate charge material in both conventional and newer ironmaking processes. The performance characteristics of these pellets are normally assessed on the basis of their reducibility values, reduction strength and resistance to clustering. These properties depend mainly on the type and amount of additives and on the sintering phenomena of the pellets during firing. In the case of composite pellets (ore-coal pellets), reduction and sintering of the iron ore fines occur simultaneously. The thermodynamic and reaction mechanisms of the processes involved in the reduction of iron ore pellets with and without reductants, additives, etc., may not necessarily be identical. The reduction and sintering characteristics of pellets greatly influence the reaction mechanism and the surface morphology of the reduced pellets. The approaches in the literature to the analysis of these reduction and sintering phenomena are broadly categorized as follows: (i) empirical models, (ii) models based on kinetics, and (ill) models based on morphological changes. The relative merits and de-merits of these models are illustrated by their application to the reduction of fluxed ore-coal composite pellets. A critical analysis of the investigations that have been conducted on the reduction and sintering behaviour of such pellets is given. It is shown that, although elegant empirical models and kinetic equations have theoretical significance and can be usefully employed in elucidating the reaction mechanisms of iron ore lumps, they are sometimes not directly applicable to fluxed ore-coal composite pellets. In studies of the latter, the approach should be to correlate the morphological changes with the reduction mechanism. The paper also gives a brief account of an investigation on the reduction and sintering aspects of fluxed composite reduced iron pellets.

Jan 1, 1996

This paper details the preliminary design work carried out before and during the implementation of an extensive backfilling programme on Cooke 3 Shaft, Randfontein Estates Gold Mining Company (Witwatersrand) Limited. The design work is of relevance to any system utilizing a cementitious binder, and the quality control aspects are of particular significance. Problems associated with correlating laboratory results to actual field results are also briefly discussed.

Jan 1, 1988

By D. J. Adams, R. G. Gürtunca

This paper describes the results obtained from a rock-engineering monitoring programme carried out at West Driefontein gold mine, where dewatered and classified tailings have been used as backfils for local and regional support. The in situ behaviour of these backfils and the surounding rockmass were determined, and it was found that the backfil used on this mine has provided significant regional support. The underground observations also showed less rockburst damage in backfiled panels than in unfiled panels, provided the backfil had been placed properly in the stopes.

Jan 1, 1991

The first commercial Corex Plant in the world capable of producing liquid iron from a variety of low-grade coals was commissioned in 1990 by Iscor at its Pretoria Works. The Plant has an annual production capacity of 300 kt of liquid iron. Because the compulsory use of coke is eliminated, the new method offers an economic and revolutionary alternative to liquid-iron production. Coke used in traditional blastfurnaces is manufactured from high-grade coal of which the available sources in South Africa are limited.

Jan 1, 1991

By B. Z. Weiss, N. R. Comins, F. Blum

Some aspects of the mechanical behaviour of chromium-containing dual-phase 3CR12 steel were investigated as a function of the temperature and strain rate. The yield stress was found to depend on both the temperature and the strain rate, with no substantial differences between the longitudinal and the transverse directions. The strain-rate sensitivity decreased with increasing temperature. The yield stress could be presented as a function of a temperature-strain-rate parameter. Impact test results showed substantial differences between the energy absorption of the transverse and longitudinal specimens above the ductile-brittle transition temperature. Changes in energy absorption with temperature were gradual for specimens in both orientations, and the transition from ductile to brittle behaviour occurred between 373 and 173 K. Strain rates ahead of the tip of notches with different geometries were calculated and measured experimentally.

Jan 1, 1990

By Z. G. He, S. H. Chen, P. Egger

A new model for hollow rock bolts which comprises rock material, hollow bolt material, bolt/rock interface, is developed on the base of the composite element method (CEM). The main advantage of the new model is that it can be incorporated into the conventional finite element analysis. So the mesh generation of bolted rock structures becomes more convenient and feasible, which is very important in the optimisation of reinforcement design: the mesh can be kept unchanged when the number and orientation of bolts are adjusted. The comparison of the calculation results with a conventional FE approach shows the robustness of the proposed method. Un nouveau modèle numérique de boulons creux comprenant la roche, le matériau du boulon creux et l’interface roche / boulon est développé sur la base de la méthode des éléments composites (CEM). L’avantage principal du nouveau modèle est la possibilité de l’incorporer dans une analyse aux éléments finis conventionnelle. Ainsi la génération du maillage d’une structure rocheuse ancrée devient plus simple ce qui est très important pour une optimisation du projet : en cas d’ajustement du nombre et de l’orientation des boulons, le maillage reste inchangé. La comparaison de résultats de calcul avec ceux obtenus par un code aux éléments finis conventionnel montre la robustesse de la méthode proposée. Auf der Grundlage der Verbund-Element-Methode (CEM) wird ein neues Modell für hohle Reibungsanker entwickelt, das den Fels, das Ankermaterial und die Kontaktfläche Fels / Anker umfasst. Der Hauptvorteil des neuen Modells ist die Möglichkeit, es in eine konventionelle FE-Analyse einzubetten. So wird die Netz-Generierung für verankerte Fels-Bauwerke einfacher, was für die Optimierung des Verankerungs-Projekts von Wichtigkeit ist: wenn Zahl und Orientierung der Anker variiert werden, bleibt das Netz unverändert. Der Vergleich von Rechenergebnissen mit solchen aus einer konventionellen FE-Rechnung zeigen die Robustheit der vorgestellten Methode.

Jan 1, 2003

This volume, which was advertised in the December, 1968, issue of the Journal at a pre-publication price of £4, is edited by W. Ryan of Warren Spring Laboratory and published by the Institute of Mining and Metallurgy, London. It is an up-to-date review of the operations of some 50 or so companies whose activities embrace the extraction and refinement of metals in the United Kingdom. Thirty-four metals are discussed, ranging from aluminium to zirconium and also there are chapters on ferro-alloys, non-ferrous alloys, high purity metals and metalloids, the platinum group metals and the rare earths. The sources of the various metals are given, followed generally by a brief description of the primary recovery process. Thereafter the operations of specific companies that deal in a particular metal are described in some detail. Certain metals such as barium, bismuth, gallium, thallium and zirconium are perforce covered very briefly as their commercial application is limited but in other cases, especially aluminium, copper lead and zinc, fairly detailed descriptions and illustrations are provided. This publication should be of considerable value to students as it presents modern procedures with regard to the refining and uses of the particular metals under review. This information may not be available from text books which in any case tend towards obsolescence. The book should also prove a valuable addition to the bookshelves of practising metallurgists providing, as it does, a schedule of most of the metallurgical companies operating in the United Kingdom. The quality of the paper and binding, the clarity of printing and illustrations and the arrangement of the subject matter are excellent and are subjects for which the editor and publishers are to be commended. R.J.A.