Search Documents

By R. A. Lohnes, S. M. Levorson

As part of research to develop a coal handleability index that predicts the ease with which coal will flow through a handling system, comparative tests were conducted with a Johanson Indicizer and a low-stress triaxial apparatus on 12 coals at a variety of gradations and moisture contents. The lndicizer test provides a rapid method for generating data associated with coal handling characteristics. The arching index measured with the Indicizer is a function of the geometry of the apparatus as well as the properties of the coal. The handleability index determined from triaxial data is a more direct measure of coal characteristics. The handleability index shows a wider range of values than the arching index and, therefore, appears to be more sensitive to coal variations. Neither the arching index nor the ratholing index, as measured with the Indicizer, agreed well with the handleability index. This is attributed to differences in sample preparation as well as to the tests themselves.

Jan 1, 1993

By W. F. Kane

Underground geologic mapping is an extremely important aspect of any on- going ground control plan. However, the actual use of data derived from such a program is difficult and often leads to subjective analysis. In this regard, computer software has been developed that utilizes a statistical determination of unstable ground conditions based on geomechanical and operational data and collected by mine personnel on a mine-wide, or regional basis. Categorical variables, such as faulting or joint frequency, are selected from local experience to form the framework of a representative data base. Statistical comparisons between the selected variables and a particular ground control problem are conducted and correlations subsequently made. The probability of encountering unstable conditions in virgin areas is assessed as information from these regions is gathered. This data can be derived from surface mapping, cores, and/or geophysical logs. As mining progresses, new data is merged with the existing data base to form a more comprehensive and extensive unit. The advantages of this approach and the acquisition and maintainence of a large data base include the more accurate representation of existing mining conditions, increased confidence in analyzing future problem areas, and elimination of the difficulties which arise when using ground control theories derived for other, often very different, locales.

Jan 1, 1986

By S. G. Malghan

Flotation is the primary method for copper minerals separation from porphyry ores. The need to process difficult-to--float porphyry copper ores presents challenges to engineers and scientists in several areas. This paper is concerned with summarizing generalized problems faced in processing porphyry ores and treatment methods to overcome them. Though some of the problems are interrelated, they are classified into three broad categories. The case studies of some of the successful applications of innovative methods to solve problems related to ore mineralogy, metallurgical aspects of ore treatment, and process variables show that quite often the problems are solvable by a judicious choice of flotation variables.

Jan 1, 1987

By S. B. Keith

Cerro de Pasco Corporation operates five large base metal mines in Peru having a combined production of some three million tons of ore a year. An integrated complex of concentrators, smelters and refineries produces annually about 25,600 short tons of copper, 48,100 short tons of lead, 60,500 short tons of zinc metal, 102,300 short tons of zinc concentrate, 8,272,000 ounces of silver and substantial amounts of bismuth, cadmium and selenium. Geology plays an important role in these operations. The organization of detail geologic work in and around the Cerro mines was set up by John M. Boutwell in 1918 and a geology department was established in 1920. Growing through the years, the department technical staff now numbers over thirty men and. their work covers all phases of geological investigations. Many outstanding geologists of the past and present, too numerous to name here, have studied and contributed to the knowledge of the deposits and the ever growing list of Cerro "alumni" must rival that of any other mining organization. Numerous papers on the geology of Cerro's mines can be found in the technical literature and several doctoral theses have been presented on Cerro subjects as indicated in the attached bibliography, Specimens of Cerro's ores can be found in museum, college and university collections throughout the world. Yet, as with all mines and mining districts, the geologic knowledge of Cerro's deposits in Peru is being revised and added to constantly. This presentation cannot hope to cover adequately all the phases of the geology and mineralization. For a more complete background and discussion of the mine you are referred to the bibliography. Here I shall outline only briefly the more important geologic features and describe some of the newer developments of recent years The credit for the data presented here belongs to the many geologists who have worked or are now working for Cerro de Pasco Corporation, but I must assume sole responsibility for any omissions or variations in the interpretation of their work.

Jan 1, 1965

By John A. Herbst, William T. Pate, A. Edward Oblad

Dynamic optimization is a cost-effective means to increase production or improve product quality in a plant. Several model-based approaches to dynamic optimization of mineral processing operations have been developed and implemented in plants. This paper reviews the phenomenological models that are the basis for dynamic optimization and the alternative methods of mathematical optimization. These methods range from theoretically complex and costly to implement to intuitively comprehensible and readily implemented.

Jan 1, 1990

By Hayward B. Oblad, Gary F. Meenan

Two optoelectronic detectors were developed by CONSOL R&D for fine coal processing applications. One sensing device is used to estimate the amount of fine coal in the solids fraction of the froth flotation tailings slurry. The other probe, based on similar technology, is capable of measuring sol ids concentrations as high as 10 weight percent in fine coal slurry streams. These patented optoelectronic sensors are installed in several CONSOL coal preparation plants and are an integral part of the fine-coal control systems.

Jan 1, 1993

By Z. Nivolianitou

This article aims at highlighting the importance of technological innovation, namely the potential use of Virtual Reality (VR) technology, as a Sustainable Development Indicator for the minerals industry. Nowadays, VR is regarded as a mature technology for real world representation, and it has been already applied in various domains such as architecture, topography, aeronautics, medicine, and lately in the process industry. Several industrial sectors already use VR tools, as the car industry for improving car ergonomics and design and the aviation industry for both pilot and maintenance crew training. It is well known that the mining industry, as well as the process industry, requires people to work in hazardous environments and situations, often inadequately trained owing to limitations in time and resources, building thus the potential for minor or major accidents.

Jan 1, 2007

By C. E. Stack

For the purposes of this presentation, "refractory clay" is intended to include any clay suitable for refractory products and thus represents a description based on industrial application. Other common examples based on use would be white-ware clay, bleaching clay, paper clay, or cement clay. Most users and producers of refractories have specific quality requirements which determine the quality or type of clay that can be utilized. Many clays can however be interchanged or substituted in use by changing manufacturing processes or upgrading less desirable clays. U.S. Bureau of Mines publications (Ampian, 1985) categorize days into six groups. These are kaolin, fire clay, ball clay, bentonite, fuller's earth, and common clay. These are practical groupings based on clay production and usage in the United States. Among these groups bentonite, fuller's earth, and common clay are primarily composed of the minerals, smectite, illite, or chlorite, and are non-refractory. Kaolin, ball clay, and fire clay are commonly used in refractories and thus qualify as refractory clays.

Jan 1, 1986

By Pierre Mousset-Jones, Felipe Calizaya

This paper summarizes the current research trends in the ventilation design for the construction of very long tunnels, and presents the results of leakage flow measurements in three auxiliary ventilation systems. The study includes an estimation of an important design parameter, namely, the leakage path resistance, and a discussion of its effects on the overall efficiency of a ventilation system. A sample problem is used to illustrate the calculations.

Jan 1, 1997

By C. H. Sampaio

The effectiveness of modem spirals in the processing of fines from Brazilian coals is assessed and discussed. Coals representing the four major coalfields in Brazil have been cleaned in Reichert LD 9 spirals in pilot and industrial plants and performance results are here presented. Normalized distribution curves for all equipment and splitters are presented and were modeled using an empirical model. These data have been compared with those for shaking tables and water-only cyclones (WOC), and it has been observed that, in the size interval investigated, spirals have indeed superior accuracy than WOC and comparative performance to tables. By analyzing experimental as well as simulation results it could be observed that although limited by the poor liberation characteristics of most Brazilian coals, significant ash and sulfur removal could be achieved using spirals.

Jan 1, 1995

By M. L. Clark

Advances in the recovery of gold from heap leaching are being made daily, but of all the systems vital to the maximum recovery of gold from a leach pile, none is more important than the methods used to construct the pile in preparation for the leaching operation. The technology described in this paper illustrates the latest systems developed to minimize compaction in the pile during its construction and reduce the cost of placement of ore on the pile. The Florida Canyon Mine of Pegasus is evaluated in detail to show reasons for its high degree of success to date.

Jan 1, 1988

By Martin F. Grier

The Mt Todd Gold Project is located 300km to the south of Darwin in the Northern Territory of Australia. The identified resource comprises 46 million tonnes at 1. 65g/t using a 1. 0g/t cut-off ( 50 million short tonnes at 0.05oz/st). The resource is open to the north and at depth. Mineralisation comprises easterly dipping sheeted quartz/sulphide veins, typically 10 to 20 millimetres in thickness, hosted by hornsfelled greywackes. The majority of the ore body is primary ore with only 10% classified as oxide ore. Early testwork showed that the ore was not suitable for heap leaching, giving only 50% recovery at a -3mm crush size. Acceptable recoveries were obtained at a P80 of 75 micron. However, the ore is extremely hard.

Jan 1, 1992

By J. W. Choung, J. A. Finch

Acid rock drainage (ARD) is a recognized environmental challenge facing mining industries. An ambient temperature ferrite (ATF) process has been investigated for treating ARD. Most nonferrous metal and calcium ions present in typical ARDs were found to be detrimental to the ATF process. Three approaches were examined, including C02 aeration, addition of complex agents and use of magnetic seeds. By introducing magnetic seeds in the ATF process, the interferences were minimized and all the precipitates formed with lime neutralization were magnetically recovered from a simulated ARD. The residual concentrations of major metal ions in the treated water were environmentally acceptable. The XRD pattern confirmed the spinel ferrite crystal structure of the products

Jan 1, 2000

By S. L. Bessinger

Introduction Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering a seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois and Kentucky and by others in Wyoming and New Mexico have shown the presence of such a gamma background (Nelson. 1989). Natural gamma coal-thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company (Consol) in Pennsylvania and West Virginia (Nelson and Bessinger, 1988). This paper describes the installation of a natural gamma coal-thickness sensor on an operating continuous miner. Previous tests had shown that the NGB-1000 coal-thickness sensor manufactured by American Mining Electronics, Inc., of Huntsville. AL, is an accurate, mine-worthy instrument. This large gamma detector consists of a sensing head and a control panel. The sensing head contains thallium-doped, sodium iodide scintillating crystal, which is coupled to a photomultiplier tube. The control panel contains the electronic components required for calibration, count conversion and display to the operator. Methods Conditions at a Consol mine in northern West Virginia require that 10 to 15 cm (4 to 6 in.) of coal be left at the roof boundary of continuous miner development sections. This roof coal is required because the shale of the immediate roof is friable and unstable. In the past, operators have used a dirt band that is usually visible near the top of the seam as a guide in maintaining the proper cutting horizon. However, this is not always reliable. Earlier observation showed that the actual thickness of the coal left on the roof varied widely; further, it was noted that occasional, accidental excursions into the immediate roof required supplementary roof control measures, such as installation of planks or center bolts. Thus, it was concluded that operators needed a better source of guidance for control of the cutting horizon, and a roof-coal thickness sensor was scheduled for installation. The NGB-1000 sensor was installed on a Joy 12CM10 continuous miner in June 1988. The sensing head was mounted on the cutter boom of the miner, and the control panel was mounted in the operator's cab. Power for the sensor was initially derived from an intrinsically safe battery power supply. Initial measurements with the sensor showed that the calibration was the same as that used in earlier tests at two other mines, indicating the uniformity of the natural gamma background above the Pittsburgh seam. Operating personnel were initially skeptical of the instrument's accuracy, and were hesitant to use its readings as a guide in maintaining a proper cutting horizon. Because gamma attenuation, the instrument's operating principle, is somewhat abstract, attempts to demonstrate the instrument's accuracy by explaining that principle were generally ineffective. It was found, however, that an operator could usually be convinced of the usefulness of the instrument by placing a large piece of coal of fairly uniform thickness over the instrument's sensing head and allowing the operator to see that the instrument reading increased by an amount very near his estimate of the thickness of the piece. The mine was provided with seven battery power supplies and a charging station. The charging station was kept in the lampman's office, and the mechanic on each shift was instructed that he was responsible for two battery power supplies each day: a freshly charged one to be taken in at the beginning of his shift and a depleted one to be brought out at the end. This system worked well for a few weeks, but eventually some battery power supplies were left in use so long that their batteries were discharged too deeply to allow recharging. In addition, transport and recharging of the batteries represented an additional task for the mechanics, who were already very busy. Consequently, a request was filed with MSHA to allow the sensor to be powered through intrinsic safety barriers by an electronic power supply connected to machine power. The permit was granted, and the sensor was connected to machine power. After the sensor was connected to machine power, the only operating problem experienced was occasional failure of cables. A supply of the required cables was made and delivered to the mine so damaged cables could be quickly replaced. Much of the cable damage could be eliminated by slight modifications to the miner during a rebuild, so that cables could be installed in more protected locations. After the sensor had been in operation for about two months, a survey was made to determine its effect on continuous miner operations. In previous research, coal thickness measurements made in 88 locations by the natural gamma method were compared to measurements made in the same locations by observing drill cuttings and by inspections of drill holes with a borescope. That research showed that the gamma method is at least as accurate as the other two methods (Nelson and Bessinger, 1989) and is also much easier to use. The object of the survey described here was not to assess the accuracy of the natural gamma measurements. but rather to determine the effectiveness of the sensor output as a guide for the operator in maintaining control of the cutting horizon. Thus a smaller, hand-held gamma detector

Jan 1, 1992

By Gordon R. Haworth

During the past ten years we have experienced a period of rapidly-changing ground rules for the mining industry. Domestically we have had to contend with numerous new regulations controlling the impact of mining-related activities on the environment. However, for the purposes of this presentation we will assume that in the United States, after a certain amount of compromise on all sides, the industry will be able to work within the framework of the new regulations, and therefore we will concentrate on offshore developments. Due to the limitations in time and scope, this paper will be directed primarily toward the metal mining industry. We contend that the U.S.-headquartered mining company should remain active, and even expand its interests in foreign countries in the future. This is our feeling in spite of recent setbacks and the low return on investment experienced in recent years by some of the metal mining companies in their foreign operations.

Jan 1, 1975

By E. K. H. Goh

A reliability-based engineering design approach for the effective design of reshaped spoil dumps was developed with the aim of obtaining structurally reliable spoil dumps at optimum reshaping costs. The aim was also to satisfy environmental erosion standards and community expectations. This approach encompasses the linking up of three major components: erosion appraisal of spoil dump designs, reliability-based engineering design of spoil dumps and costing of spoil dump reshaping practices. This paper addresses the application of the reliability-based engineering- design approach to the assessment of spoil dump designs for erosion control. Included are various types of erosion prediction models and reliability-based engineering-design analytical techniques. Also included is a case study that demonstrates the application of this approach.

Jan 1, 2000

By Robert A. Hains, William P. Balaz, K. Payne

Ceramics are usually used to line chutes, pipes, dust collectors, separators, cyclones or bins where abrasive or corrosive material is moving. Improvements in ceramic manufacturing methods and quality, use of other abrasion resistant materials in combination with Alumina ceramic, improved adhesives and installation methods allow the use of Alumina ceramic tile in applications with impact. This paper discusses the criteria to determine if ceramics can provide a cost effective alternative to other liners for abrasive material handling applications, design parameters for liner systems, system costs, and case histories. The goal will be to provide a practical guide for improving the performance of existing ceramic lined systems or determining if ceramics is a cost effective solution for your abrasive material handling applications.

Jan 1, 1996

By Nader Shahcheraghi, Verya Nasri, Mehdi Bakhshi, Ali Haghighat

An accidental fire load is one of the major loads considered in design of segmental linings in transit tunnel. Typically, a two-dimensional coupled thermo-mechanical finite element analysis (FEA) is conducted. The conventional approach involves using standard fire curves (temperature-time curves) which can lead to a significant overestimation of fire load and tunnel lining thickness in metro tunnels. The focus of this paper is on the cutting-edge approach, using 3D computational fluid dynamics (CFD) analysis of real train fires in metro tunnels and coupled thermo-mechanical finite element analysis (FEA) to accurately and cost-effectively design fiber-reinforced concrete (FRC) segmental tunnel linings for large-scale metro projects.

Jun 23, 2024

By Steve L. Bessinger, Luis B. Giraldo, Joram Shenhar, James D. Pile

This paper discusses the Helical Drag Bit (HDB) and its rock drilling applications with an emphasis on use in mining operations. The HDB is a drilling tool that employs cutting members arranged in a pattern to form a helical groove or thread within a borehole. This pattern of cutters can be used for several purposes including roof bolting in mining, interpretation of the lithology of the strata being drilled and low energy consumption drilling. Laboratory and field experiments have consistently shown increase of roof bolt-anchoring capacities in weak rock of more than 100% using the short encapsulation pull test method when boreholes are conditioned using the HDB. In 2004 a series of tests conducted in mines with weak roofs demonstrated the benefits of HDB technology for roof bolting applications in mining. HDB technology offers opportunities for new and beneficial approaches to interpret the geology of roof strata. During conventional drilling, traditional approaches to determine rock properties require simultaneous measurement of several parameters such as thrust, rotational velocity, torque and penetration rate. The unique geometry of the HDB possesses a characteristic that allows determination of the mechanical properties of the rock being drilled by measuring torque as a single drilling parameter. This capability greatly simplifies the process of determining rock properties and provides reliable results. Additionally, HDB technology has been demonstrated to offer significant advantages for rock drilling. A substantial portion of the rock is removed by the fracturing of the internal thread created in the rock bore by the tool taking advantage of the weakness of the rock in tension. Because the rock chips obtained in this process are relatively large, savings in energy are realized when compared to traditional drilling technologies.

Jan 1, 2005

By P. Huttagosol

The use of computer models to design ultimate pit limits during feasibility study and long range mine planning is becoming a significant practice in open pit mining. One of the problems in determining optimal ultimate pit limits using true optimization techniques has been they require a great deal of computer memory and execution time. In this paper, the maximum closure of a graph, which is a true optimizing model developed by Lerchs and Grossmann, is modified for solving ultimate pit limit problems. By using some properties of the original L&G graph algorithm, the tree configuration can be reduced to only connections between positive ore nodes. The modified algorithm is shown to require less memory and processing time while still yielding an optimal solution.

Jan 1, 1989