Search Documents

By M. G. Karfakis

Grouting has been used in underground mining for more than twenty years. Chemical grouting is often used as a remedial measure when the implemented ground control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. Utilization of the polyurethane grout currently being used is restricted by its limited range of physical and mechanical properties that restrict its utilization. To overcome some of the drawbacks of polyurethane, research has been conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as StrataGrip, provides a number of features, including variable gel times and much reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted. Assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research have defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1997

By Pieter Hoekstra, Jim Hild, Mark Blohm

In the Basin and Range Province of Nevada, geophysics is used to assist exploration for bulk minable gold deposits, particularly over pediments. It is employed for mapping thickness of alluvium and Tertiary valley fill, for mapping covered structures, and for identifying alteration zones. In addition to potential field and seismic methods, three different electrical and electromagnetic methods are frequently used, resistivity-induced polarization, controlled source audiomagnetotellurics, and time domain EM. A review and comparison of the principles of these methods, illustrated by case histories, is the topic of this paper.

Jan 1, 1989

By Robert F. Randolph

New technologies confront mining organizations with unprecedented human factors challenges. Likely problem areas range from the design of the human- machine interface to the design of work groups and mine organizational structures. However, these human design considerations are commonly ignored in most industries, resulting in a failure rate of 75% for advanced technology programs. The U.S. Bureau of Mines is addressing these concerns through a program of research on the human side of high technology mining systems. Interviews with mining industry participants and researchers have identified concern in several areas, including training and equipment design. Although new mining technologies promise to improve overall safety by relocating miners away from hazardous areas, data from MHSA accident reports and other sources suggest that certain types of new hazards may be created. Many of these new hazards can be reduced though a systems approach to ergonomic design of equipment, tasks, and work processes. This evidence, combined with reviews of high technology human-machine systems in other industries. can help in the design of safe and efficient future mining technologies.

Jan 1, 1992

By C. Pomeroy, J. Weyer, J. Brune

"Mining began in the Erzgebirge (“ore mountains”) region of Saxony, Germany more than 800 years ago, and extensive underground workings cut through the entire area. Some of these old workings are still used today: not for production, but for offering an underground venue for research, tourism and university teaching. One example is the Reiche Zeche mine at the Technische Universität Bergakadamie Freiberg which hosts one of the oldest mining engineering programs in the world. It is imperative to keep all active mine workings well ventilated to make the mine safe for students, visitors and researchers. Since the mine workings at Reiche Zeche are so vast, extensive and, to a large extent unexplored and unmapped, it has been difficult to provide a complete, functioning and adequate mine ventilation model for this mine that accounts for all known and unknown leakage air flows. Researchers at the Colorado School of Mines have cooperation with their colleagues at Freiberg to establish a mine ventilation network model based on a limited number of air readings in known and accessible drifts. In order to balance the measured air quantities, leakage flows were quantified and mapped by comparing input and output flows of mapped drifts, and modelled using Ventsim Visual, a powerful visualization software package. The resulting mine ventilation model is used to locate and quantify the leakage air flows and to examine how much air is lost in each area. With this model, ventilation changes and improvements underground can be documented reflected in the model. This enables the Bergakadamie Freiberg to project air changes required for scientific experiments and to set up mine ventilation in specific areas and for specific needs. The model also enables better ventilation control and monitoring than before. Finally, the model can be used to predict ventilation changes and escape way contamination in case of a fire, ground fall or inundation in the mine. The latter becomes important as the lower mine workings are often flooded during spring runoff, which has created uncertainty about mine ventilation in the past. HISTORICAL BACKGROUND The discovery of silver, lead, zinc, tin and other valuable metal ores in the Erzgebirge region of Saxony, Germany began in the12th century and started a mining boom than lasted for centuries. Surface mines quickly developed underground to access the higher grade veins. Explored by the early geologists and driven by the ingenuity of the miners, the underground works expanded vastly throughout Freiberg and the surrounding region. Development followed the highest grade veins, and engineers developed solutions to drain water and provide limited ventilation to the underground workings. Still, engineered and planned ventilation was usually not a priority in the development of a new drift, which today makes ventilation modeling a significant challenge."

Jan 1, 2015

By Jan M. Mutmansky

While production scheduling for both surface and underground mining operations is similar in nature, a rather large array of techniques is applied in solving such planning problems. The techniques consist of both rigid operations research (OR) methods and practical procedures which are not mathematically based. In the following sections, a short summary of some of the techniques that are applicable to production scheduling problems in mineral operations is presented. The techniques discussed are: linear programming, integer programming, dynamic programming, graph and network theory, simulation, and heuristic methods. For an in-depth comprehension of these techniques, the reader is referred to any of the available textbooks on these subjects. One or more references will be listed for each topic to provide a starting point.

Jan 1, 1979

By J. A. Herbst, S. L. Blust

Optimization of blasting, crushing, and grinding operations is filled with challenges. One of the more difficult tasks is accurately sampling and determining the size distributions of blasted and crushed materials at a reasonable cost. The task is difficult because of the large size of fragments and the tonnage involved. However, the size distribution measurements are necessary for models that predict the performance of mine-through-mill operations. This paper is concerned with the use of video sampling for this task at National Steel Pellet Company's operation in Keewatin, Minnesota Data gathering, data analysis, model building, and mine-to-mill simulation are all described.

Jan 1, 2000

By Makoto Terada

The most important consideration in planning the plugging and sealing of a mine for mine water control is to predict the water flow from the mine. For this purpose, a method of numerical analysis on the water behavior in the ground at the concerned mine area was developed and the mine water flows were simulated. A hydrological survey at the surface of the mine determined the recharge rate of ground- water and the apparent permeability of ground.

Jan 1, 1982

By Robert F. Jones

INTRODUCTION Upflow Solids Contact Clarification is a process long employed in the treatment of potable water, wastewater and municipal sewage. This process incorporated in a fiberglass conical structure seems to offer an economical solution to problems encountered in reduction of particulates in uranium effuents. CONCEPT OF UPFLOW CLARIFICATION Use of suspended solids contact units date back to the 1930's. These types of units produced by Infilco and the Permutit Company, among others, were used in the Lime-Soda softening process to precipitate calcium and magnesium salts from hard water. In general, the process operated as follows: (a) Raw water entered a central chamber where it was mixed with chemicals. The chamber had provisions for agitating and circulating the chemicals so that mixing and reaction zones were formed. (b) The water, precipitated chemicals, floc and turbidity flows to a clarification chamber (the Permutit precipitator used a truncated cone). In most cases the influent then passes upward through a blanket of suspended floc and other solids before it leaves the chamber at effluent weirs or launders.

Jan 1, 1984

By Sizhe Tan

An open pit mining operation can be considered as a production system with at least two products: ore and overburden (waste). A primary mine planning task is to schedule the production of ore and waste over its life span subject to several technical and economic constraints to maximize some objective such as the overall profit from the operation. Two major constraints are (i) the feasible combinations of ore and waste productions and (ii) the limiting function for ore production as a function of mine life. The task in scheduling production and stripping ratio (ratio of waste to ore production) is to find an ore production curve below the upper bound function of ore production, and a stripping ratio curve within the feasible domain of ore production and overburden removal while maximizing the defined objective. Zn this paper, feasibility of developing computerized optimization models to perform such a scheduling process is explored. Two optimization models are proposed for the task. In the first approach, a linear programming (LP) model is employed and in the second, a dynamic programming procedure (DP) is outlined. In these models, in addition to the consideration of the two major constraints mentioned earlier, various other contributing factors such as interest rate, equipment purchase cost and installation schedule, operating cost, and equipment idle cost are incorporated. An example is provided to illustrate the LP model application.

Jan 1, 1992

By R. Larry Davis

Over the past decade there has been a continual decrease in domestic oil reserves accompanied by a sharp increase in the demand for energy. Even with increased imports of foreign oil, the energy demand has not been met. This has forced many users to turn to substitute fuels. Of the many substitute fuels available most users are turning to and creating an increased demand for low sulfur coal. Because of the increased demand for low sulfur coal as well as the inherent problems in producing eastern coal, many producers have turned their attention to the large deposits of low sulfur coal in the western United States. Western coal mining is, however, not without its problems such as high moisture content, high ash content, highly variable sulfur content, multiple seams, and/or pitching seams. It is to aid in the solution of these problems that this chapter is directed.

Jan 1, 1979

By E. J. Garrison

Discussion by E.J. Garrison A.C. Noble presents a clear and concise summary of the factors pertinent to a competent reserve evaluation of a mineral occurrence. However, I believe that he confuses the difference between a resource and a reserve. By definition, a reserve estimate includes all known economic, legal, mining, metallurgical and environmental factors impacting the recovery of the product(s) found in the deposit. A resource estimate, however, is an estimate of what is there - what is available for exploitation and should not include economic and other considerations. Only after defining the resource, its extent, location, physical and chemical properties, can an intelligent selection process begin of the extraction and processing technologies most appropriate to the circumstances encountered. The early and almost certainly inappropriate application of these often cookbook choices has probably lead many companies to walk away from good properties. (How many mines have been found in others rejects?) An example of the process is the early selection of metallurgical samples, after encouraging values are found in a few holes or surface samples, in an attempt to determine the economics of the prospect. Unfortunately, the sampler does not know how representative of the occurrence the sample is because he does not know what the deposit looks like. As a consequence, the property becomes saddled with a bad metallurgical sample that is often inappropriately used in evaluating the deposit which it does not represent. Reply by A.C. Noble E.J. Garrison asserts that I confuse the difference between a resource and an ore reserve. In fact, this paper was motivated by the observation that resources and reserves are almost universally confused throughout the industry. While Garrison is concerned that too-early consideration of engineering, metallurgical and economic factors will result in dropping properties too soon, some issues that must be considered include: •The purpose of exploration is to discover ore reserves, not to discover resources. •Ore reserves are always smaller than resources. • Decisions on exploration expenditures must be made based on the expectation of the quantity of ore reserves that will ultimately be defined. Noble's Fig. 2 can be used to give guidance as to when it is appropriate to begin reserve calculations. When exploration enters the "flat" portion of the curve, representative samples can be selected for metallurgical studies and appropriate mining methods chosen. It is at this stage that we know enough about the deposit to make intelligent choices of representative samples and recognize constraints on mining caused by the deposits shape, environment and physical properties. Once the appropriate technologies have been chosen, then their cost can be estimated with reasonable accuracy. Early entry of economic and process factors gives the false appearance of reserve status to the resource estimation. It would be more informative and less subject to abuse and misunderstanding if resource calculations were made at a number of cutoff grades. The cutoff grades should be chosen to cover the range of grades found in practice in existing operations of similar type. This would emphasize the open nature of resource estimates and encourage creative evaluation of mining and process technologies. It does not preclude the use of economic, environmental and recovery technology factors in deciding the advisability of continuing exploration expenditures, but would highlight their speculative nature. It is thus hoped that decisions on the future of the deposit would not be made on the presumed suitability of a given technology but on the actually known reality. I agree that resource estimates should be reported as a range of cutoff grades. Since reporting at a cutoff implies application of underlying economics (even by analogy to similar properties), however, it should be clearly stated that resources do not consider economic, mining or cost factors, and that ore reserves will be substantially less. The dilemma of the explorationist is that until the continuity and limits of ore-grade mineralization have been established, it is difficult to make quantitative estimates of either resources or ore reserves. Further industry discussion is needed regarding standards for disclosing early exploration information in such a way as to fairly represent the potential of an exploration property.

Jan 1, 1995

By Juan L. Yarmuch, Hyam Rubinstein

Open-pit mine planning is a key process in the definition of mineral reserves and their efficient removal. Ore in open-pit mines is extracted bymining sequential pits called pushbacks. Pushbacks need to satisfy complex geometrical constraints to ensure the efficient usage of equipment. To date, no algorithms that both account for those constraints and maximizeNPV, are commercially available. Therefore, pushback design is done by engineers relying on their expertise to incorporate practical features intothe output of commercial tools. In this article, we present a new algorithm that produces close to optimal practical pushbacks and we illustrate its performance in real mines.

Jun 25, 2023

By P. Hadzeriga

Ion exchange techniques have been growing fast and spectacularly in all phases of Science for the last two decades, but still its acceptance as a unit operation in Metallurgy is resisted. Mainly this is because ion exchange procedures are thought of as glamorous techniques by which only relatively expensive metals are to be recovered. Perhaps this concept comes from the early and basic marriage of uranium and other high price metals and ion exchange procedures. The general trend is that ion exchange technique requires equipment and materials which are too expensive to economically perform a chemical step whenever "cheap" commodities are produced. However, we are here presenting a means of utilization of waste hydrochloric acid by an ion exchange technique. We have studied this from the engineering and economic standpoint in a number of variations of the main procedure discussed here and we-conclude that under proper economic circumstances, the cost of the ion exchange material as well as the equipment and labor involved in the ion exchange section, is by no means unreasonable.

Jan 1, 1964

By Steve Kral

Competition in the gold mining industry throughout the world has become fierce in recent years. The challenge facing operations personnel is to produce more gold for less money. Likewise, the explorationist's charge is to find more gold in a more cost-efficient manner. That means using new technology to find new gold deposits and expand present ones. More accurate mapping instruments are available to geologists in the search for new deposits. Advanced geophysical and geochemical methods enable explo¬ration teams to review previously mined districts in their search for minable reserves. Four technical sessions on the geology, exploration, and development of gold deposits were part of the program at `world Gold '89,' a Gold Forum on Technology and Practices," held by SME and The Australasian Institute of Mining and Metallurgy in Reno, NV, Nov. 5-8, 1989.

Jan 1, 1990

By M. S. Prasad, K. J. Reid, M. P. Katsoulis

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two-year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the various process options adopted on bulk samples collected from the Minnesota River Valley area, which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion. HGMS and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size-reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota are briefly discussed.

Jan 1, 1992

By C. Timothy Shaw

Traditionally, only the large mining companies have maintained specialist departments in such areas as Rock Mechanics, Ventilation and Safety. To the small companies this has been a luxury that they could ill afford. Any work required by such companies in these areas, more complex than could be handled by the existing staff, was done by consultants. This situation is changing though and there is a need arising for many specialist departments. These changes are partly being brought about by the effects of inflation as the ever increasing costs are causing more and more operators to increase the size of their operations in search of economies of scale. In addition though the plethora of new laws and regulations are creating a need for many more specialists in all areas of mining in order to ensure compliance. The abovementioned factors, added to the existing Pattern of mines endeavoring to improve the working environment for their labor force, both for reasons of practical labor relations and also due to further legislative pressures, have thus created a climate where, in the near future, departments such as Rock Mechanics, Safety, Ventilation, Environmental Engineering and Subsidence Control will be commonplace in mining companies. It will no longer be practical to function without such services. Many mining companies already maintain such departments and this has particularly been true of the big mining groups of South Africa. From the experience gained by many of these large companies with specialist departments, it is clear that the maintenance of a cadre of experienced, competent professionals in such a department has not always been easy. It would seem from the experience gained that one can generalise and state that graduate mining engineers tend not to view specilisation as an optimum direction for their career development. It is of course true that many professionals, especially those with higher than a bachelors degree, do view these areas as valid career options, but even here experience shows that wastage is high. The time therefore seems to be ripe to take a look at this area in some detail to see whether reasons for the problems can be isolated. Working from that some suggestions can be made as to directions in which improvements might be made. If the challenge of the demands of the new regulations are to be met then such improvements must be made.

Jan 1, 1980

By D. R. Tweeton, L. W. Lake

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of ground-water quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be per¬formed in two or three weeks. It is relatively inexpensive, requiring one injection-production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin and was partially funded by the US Bureau of Mines.

Jan 1, 1987

By P. D. Lafleur

A concerted effort to determine the quantities and effects of trace elements in the environment requires the application of a number of different analytical techniques in the same or in different laboratories. The interpretation of analytical data is often difficult because of differing results between analysts or even by the same analyst at different times. Standard Reference Materials (SRM), which are certified for their trace element content and are in a matrix similar to the one of interest, can greatly increase the accuracy of analysis and the reproducibility between laboratories. The United States National Bureau of Standards (NBS) has developed a number of SRMs applicable to the determination of trace elements in environmental materials. Two of these, SRM-1571, Orchard Leaves, and SRM-1577. Bovine Liver, are excellent for biological tissue analyses. Several new standards are of value for fossil-fuel analyses. These are: SRM-1632. Trace Elements in Coal; SM-1633, Trace Elements in Fly Ash; SM-1634, Trace Elements in Residual Fuel Oil: and SRM-1635, Trace Elements in Gasoline. In cooperation with the US Environmental Protection Agency, the NBS has recently concluded an interlaboratory comparison involving analyses by more than 60 laboratories on these fossil-fuel materials. The resulu of this intercomparison and the broad range experience with the biological materials will be presented showing both intratechnique and intertechnique variations, and the sensitivities and comparisons with the values certified by NBS.

Jan 1, 1975

By G. Y. Li, D. Farahmand

The dilemma of a numerical analyst not only concerns the problem of modelling the non-linear behaviour of intact rock, but also the non- linearity contributed by structural discontinuities. In this light, it is the intention of this paper to examine some aspects of the non-homogenity and structural discontinuities of rock and incorporate this behaviour into boundary element numerical solution. Non-homogeneous material is considered piecewise, thus homogeneous and is modelled by using sub-regions. The Mohr- Coulomb failure criterion is employed to model the non-linear behaviour of the major discontinuities. A computer program is developed based on the procedure for combining the direct boundary element method and the displacement discontinuity method. A linear element type is employed in the formulation of numerical solution. The computer program is used to study the stress distribution in a gold mine.

Jan 1, 1986

By R. K. Young

Producing a sound plant design for a major project requires hundreds of engineers and many drawings. Economical accomplishment of this task is based upon careful and orderly organization of the design team so that at all times there is a complete and workable staff but at no time a surplus of costly talent. This paper will describe the various stages in the development of plant design which normally follow the laboratory and pilot plant investigations discussed in other papers today. An outline of the procedures used in the assembling of a project design group, within an established engineering organization will be presented. Actual procedures may vary according to the size and character of the plant, the special requirements of the owner, and the make-up of the engineering organization performing the design, but most of the points covered will be found to be basic to any plant design project.

Jan 1, 1960