Search Documents

By A. Casuge, D. Lee, J. A. Finch, C. C. Sui

The adsorption of copper and lead und their subsequent xanthate uptake were compared at pH 3.0, 6.0 and 9.2 on both fresh and oxidized sphalerite. The extent of adsorption and the rate of adsorption were strongly dependent on pH, with the highest adsorption of Cu and Pb being at pH 9.2. In the presence of both Cu and Pb, Cu adsorption was enhanced and Pb adsorption was suppressed. The adsorption kinetics of Cu and Pb were characterized by two- and three-stage adsorption processes, respectively. The exchange ratio of Cu to Zn was about one and that of Ph to Zn was greater than one and varied with pH. The uptake of xarlthate on "activated" sphalerite was dependent on pH. The rnaximum uptake was found to be at pH 6.0 for Cu-activated sphalerite artd at pH 9.2 for Pb-activated sphalerite. A measure of "activation strength" based on inetal ion adsorption and xanthate uptake was introduced. The activation strength of Cu to Pb was about one at acidic pH, but it was higher at neutral (pH -6) and alkaline (pH -3) conditions. The oxidation of sphalerite decreased Pb and, especially, Cu adsorption and decreased xanthate uptake.

Jan 1, 2000

By M. S. Vernon, J. J. Kellar, W. M. Cross, R. M. Winter, F. J. Johnson, A. G. Pommer

Three substrates (MgO crystal, CaF2 crystal and Mg plate) were used to construct thin layers of Mg(OH)2. Various routes were used to modify these substrates, including surface hydration and sol-gel coating. In each case, it was found (by using Fourier transform infrared spectroscopy) that thin layers of Mg(OH)2 could be produced. In the case of hydrated layers, the surface morphology of the Mg(OH)2 resembles the bulk platelet shape of precipitated Mg(OH)2.

Jan 1, 2000

By Charles A. Ramsey, Kathleen S. Smith, Philip L. Hageman

We developed a statistically based strategy for sampling the surficial material of mine-waste dumps for use in screening and prioritizing historic dumps on abandoned mine lands. This sampling strategy entails the collection of a representative composite sample from individual dumps and allows for regional or watershed-based assessments. One 30-inment dump-composite sample collected using this sampling strategy contains as much information, relative to average value, as 30 individual grab samples at 1/30 of the analytical cost.

Jan 1, 2000

By D. R. Spears, C. E. Jordan

The U.S. Bureau of Mines examined the influence of turbulence on the fine bubble flotation of fine-sized (minus 40 micron) galena in order to improve flotation efficiency. Fine bubble flotation was carried out in a spinning-disk flotation cell and was compared to results obtained from flotation in a conventional cell at equivalent agitation levels. An automated electrochemical technique was used to monitor the turbulent velocity distributions of the fluid within the cell as a function of time and position. The velocity profiles were used to increase the precision of the fine particle, turbulent flotation model. While improved flotation response was obtained with intense agitation, the effect of bubble size was small. These results matched the model's predicted response for fine particle flotation.

Jan 1, 1989

By D. A. Stanley, B. J. Scheiner

The U.S. Bureau of Mines has thoroughly investigated the flocculation of phosphatic clay waste with polyethylene oxide (PEO). The studies included both theoretical and applied aspects of the flocculation sequence. The screen dewatering technique developed by the Bureau was field tested at four different Florida phosphate mines. The results of these field studies are presented. Also, to determine the mechanisms of the interaction of PEO with montmorillonite clays common to the phosphatic clay waste, a number of theoretical studies were conducted. An empirical equation was developed to describe the amount of PEO needed for flocculation. Infrared, ion exchange, and rheology techniques were used to study the interaction of PEO with Florida clays. The results of these studies are also presented.

Jan 1, 1993

By Neville T. Moxen, Stuart K. Nicol, Malcolm D. Engel

Ion flotation is a process in which ions of interest are complexed with a suitable surfactant molecule. A dilute solution containing these complexes is then aerated, under which circumstance the surface-active complex concentrates at the air-water interface and is transferred to a froth. The present work describes some of the phenomenology of this process and experimental work leading up to the design and use of a pilot scale laboratory facility. Early experiments suggest that selective recovery of gold can be obtained in a manner at least equivalent to conventional CIP processing at low capital cost. Under favourable conditions, upgrade ratios of gold ions of the order of 180: l have been achieved from reclaimed residue dam water with as low an initial gold level as 0.2ppm. Successful development of countercurrent ion flotation for concentrating solids-free gold solutions may offer a lower cost alternative to existing gold ore processing technologies, or in more secondary applications such as concentrating dilute gold solutions or heap leach runoff. The technology may also have more generalised applications to other heavy metal processing.

Jan 1, 1990

By Robert A. Jankowski, Natesa I. Jayaraman, Jay F. Colinet

The U.S. Bureau of Mines evaluated the dust control effectiveness of two-phase flow systems in a full-scale model mine using a mockup of a Joy 14CM continuous mining machine. In a two-phase flow system, air and water flow simultaneously through the nozzle. Air pressure varies from 10 to 60 psi, and water at 30 to 50 psi. Coal dust was introduced at the face, and dust concentrations were monitored at the operator locations and in the return. When compared with a conventional spray system, a symmetrical two-phase flow system reduced dust levels during the box cut by 43 pct at the operator location, and 30 pct in the face return. Dust levels, however, increased at the off-operator position during the slab cut. A directional two-phase flow system reduced dust levels at both operator locations by more than 90 pct in the box cut mode. While the use of two-phase flow systems will reduce respirable dust levels and water usage, it requires an air supply to the miner. Moreover, the ability of the two-phase flow system to redirect the dust cloud makes nozzle orientation a critical factor.

Jan 1, 1991

By Ahmet Gursoy

Maryland, will be the widest vehicular tunnel ever built by the trench tube method. Careful coordination and planning were required to meet the tight and fast design and construction schedules. During the preliminary design, traditional design drawings were bypassed in favor of 25 preliminary design reports representing major work breakdown structures (tasks). For each task, alternative design solutions were examined and analyzed by means of trade-off studies on the basis of engineering, constructibility, and economic considerations, thus providing an overall conceptual value engineering approach for the entire project. So far, total value engineering proposed by the contractor for Contract I I (largest contract of the project at $245 million) is less than 1.5 percent of the contract value. This is an important indication of the success of the design phase planning.

Jan 1, 1983

By R. G. Reddy

Iron solubility's in spent pickling (HFHNO3 -H2O) solutions were determined as a function of HF and HNO3 acid concentrations. A chemical analysis of the industrial pickling solutions and sludges was performed. The stable phases observed in the sludges are FeF3.3H2O and (FeCr)F3.3H20. Pure Fe metal, AISI 316 stainless steel and AISI 416 stainless steel were used in this study. The results show, that the solubility of Fe increased as the concentrations of HF increased in the pickling solution at a fixed concentration of HNO3. A reasonable agreement between the experimental solubility data and the theoretical calculated data was obtained. X-ray diffraction analysis showed that the solid solubility product formed in the ternary solution containing pure Fe is mainly, at a high pH value, FeO(OH) compounds and, at a low pH value, Fe F3.3H2O compounds.

Jan 1, 1994

By P. Anciaux

The EUs? manufacturing and construction industries are vital to Europe?s economy. They rely heavily on a steady supply of materials which meet appropriate quality criteria and are available at a competitive price. The steadily rising global demand for (non-energy) raw materials due to increasing consumption in upcoming economies such as China, India and Brazil, is in some cases leading to rapid price increases, but also supply disruptions which affect the European industry chain. These considerations are at the basis of new policy initiatives that are being prepared by Enterprise and Industry Directorate-General in relation to the competitiveness of the European metals industry. Over the last year the raw materials supply issue has increasingly become the topic of de-bate among various stakeholders. In July 2006 the European Economic and Social Committee adopted an opinion on risks and problems associated with the supply of raw materials to European industry. It is therefore important to identify and analyse the future needs for European industry, the possible constraints and impacts on its competitiveness. The raw materials supply issue should also be looked at from the view-point of the EU extractive industry, which plays an important role in supplying raw materials to the downstream industries and which faces very specific challenges. Within the Enterprise and Industry Directorate-General the different factors that influence the competitiveness of the non-energy extractive industry are being assessed, in order to help identify policies and actions which could contribute to and enhance the competitiveness of the industry.

Jan 1, 2007

By V. K. Karra

An improvement in the present day screen sizing methods calls for knowledge on i) how material in the size range: 0.5 x 1.5 times the through-fall opening of the mesh on a deck, splits between the oversize and undersize streams of the deck, and ii) how near-mesh content of the feed affects the screening performance. In the throughput based sizing method given here, this is accomplished through the introduction of a generalized partition curve and a near-mesh factor. A newly developed efficiency factor is employed in addition to the traditional screen sizing factors.

Jan 1, 1979

By K. Baba

Liberation of valuable minerals from a gangue matrix during size reduction of multiphase mineral particles is an important objective in mineral separation processes. A methodology for the prediction of volumetric grade distribution from one dimensional, linear intercept image analysis is being developed using a transformation function to describe the relations hi p between the linear and volumetric grade distributions. As part of this research effort it has been found that a transformation function, derived from Monte Carlo simulations of irregularly shaped particles, mainly depends on the volumetric grade and the dispersion density, i.e., the number of nuclei (or grains) per particle. A possible mathematical form for the transformation function is described in detail.

Jan 1, 1985

By M. Fornaro

A small size quarrying activity (3 different quarries with an overall production in blocks less than 10.000 m3/year) has been exploiting for a long time the ?Tonalite? deposit of Adamello-Presanella. In 1967, given the outstanding natural beauty of the area, a natural park has been established with the aim of preserving environmental quality and, at the same time, of providing a sustainable development to the area. Because of the potential impacts of a mining activity in such a context, a specific study has been recently carried out in order to define if and how the quarries could co-exist with the park, beyond the ?administrative results? of a classic environmental impact assessment. The paper deals with the process that drove to the conclusion that the activities are not ?a priori? incompatible with the aims of the park. In the opinion of the authors, a responsible quarry management, which must take inspiration from the care given to environment by traditional alpine productive activities (e.g. the use of water, of wood, and of the stone itself), and take advantage of modern technologies in terms of emissions and safety, can be considered not only compatible with the protected area, but even able to positively contribute to the protection of the land and environment (Barisone et al., 2001). A series of specific prescriptions, which have been adopted by the Park Authorities after this study, are also discussed in the paper: only the definition of suitable spatial and temporal limits, the adoption of effective technical practices and a strict control are considered to be able to drive this ?exceptional? activity towards the final goal of real sustainability.

Jan 1, 2007

By John W. Greene

ennec?tt's Bameys Canyon Mine personnel developed an mnovahve process to extract gold from a small (1.8 million tons) sulfide ore zone in an oxidized ore body located at the Bameys Canyon Mine. This approach consists of extracting the sulfides from the ore via flotation, shipping the concentrate to Kennecott's new smelter, and mixing the flotation tailings with the oxide ore, agglomerating the mixture, and stacking the resultin tailings/oxide ore combination on the heaps. Conventional heap leaching technology is utilized to recover the gold from the mixed materials. Overall, the total gold recovery from the sulfide ore is esti­mated to be 90%. This approximation is based on a smelter gold recovery of 98% from the concentrate and an 88% recovery from the tailings during heap leaching

Jan 1, 1996

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By J. D. Miller

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By Michael F. Tucker

Dealing successfully with intercultural issues is critical for success on an international assignment. This is true not only for employees but for the accompanying spouses and children as well. This paper presents a set of research-based competencies required for successful life and work in another country, such as open-mindedness, flexibility, and respect for the beliefs of others. Best practices for training employees and their families bound for international assignments are also presented.

Jan 1, 2001

By Gerald P. Kelton

Over the past quarter of a century, the success of the hydrocyclone as a classifier in closed circuit grinding installations has permitted the introduction of the cyclone into virtually all fields of wet industrial processing. Research and experience gained in these applications have established the optimum cyclone sizes and designs necessary to provide the required performance. Although cyclones are used in widely diverse liquid-solid applications, their use for ultrafine separation clearly demonstrates the importance of a familiarity with previous case studies. Krebs Engineers is firmly dedicated to serving the process industry and has acquired the unsurpassed knowledge and experience to handle all types of separations and classification problems. Cyclones have been used for a number of applications to make what might be considered fine separations. A typical example is in an iron ore grinding circuit where a 381 mm diameter cyclone will classify an overflow product to 85% -44 micron. There is no question that this is a fine separation, but still finer separations are possible, and these are known as ultrafine separations.

Jan 1, 1983

By T. Brady, J. Johnson, J. Whyatt, B. Pariseau, M. Stahl

An elastic-viscoplastic material model allows for time- dependent rock mass motion in proportion to excess stress above the elastic limit. The model produces rounded stair-step curves of displacement vs. time that are similar to those obtained from recent borehole extensometer measurements made in the central portion of the Ross Shaft pillar at the Homestake mine. The work in progress, including two- and three-dimensional finite element analyses using the UTAH2/3 codes, indicates that the model is a step towards more realistic safety and stability analysis, but that inclusion of rock mass damage may be desirable.

Jan 1, 2000

By R. K. Mehta

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated for a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1989