Search Documents

By Stephen J. Brower

Located in Central Nevada, The Round Mountain Gold deposit has been continuously mined since 1977. Present proven and probable reserves are 226 Mt (250 million short tons) at 1.1 g/t (.032 oz per short ton). The current open pit mining rate of 118 Kt (130,000 short tons) per day is producing 41 Kt (45,000 short tons) per day of ore to be processed by heap leach methods. At this rate, the current reserves provide a 16 year mine life. The high mining rate and strict ore delivery requirements mandate comprehensive and realistic mine planning. The mine planning process is described in three general steps: Deposit Modeling; Mine Design; and, Production Coordination and Support.

Jan 1, 1989

By Andrzej Luszczkiewicz, Kazimierz S. Sztaba

Flotation tailing of Polish copper sulfide ores represents more than 90% of the mass of run-of-mine ore. The tailing contains mainly quartz, dolomite, clay minerals, traces of sulfides, and some accessory minerals. Almost all minerals of the tailing are well liberated and, therefore, any further beneficiation process applied to the tailing is expected to be inexpensive. In this work, results of investigations on utilization of flotation tailing using classification and gravity concentration are presented. It is shown that due to classification of flotation tailing in hydrocyclones, the coarse fraction becomes suitable material for gravity separation providing backfill material for underground mines as well as heavy minerals, a source of valuable rare elements. It was also found that heavy minerals separated by gravity methods contain a significant amount of rare elements such as zirconium, titanium, silver, rare earth metals, and uranium. The light fraction of the gravity separation contains well deslimed quartz particles and meets strict requirements for hydraulic filling material ked for structural support in underground mines. Evaluation of the cost of the proposed technology indicated that investment to implement the method would provide a return within 2-4 years.

Jan 1, 1995

By D. M. Milne, H. H. Kanduth

INTRODUCTION The past few years has seen an increased interest in the determination of statistically valid properties of a rock mass. The increased use of computer modelling for the study of rock excavation behaviour has created a need for upper and lower statistical bounds for the properties of a rock mass being modelled. Obviously, to determine the statistical properties of a large volume of rock, many samples must be tested - an expensive proposition when using conventional testing facilities and procedures. As a result of high costs per sample, sufficient tests for statistically valid results are rarely done. In an effort to reduce both sample preparation and test facility costs, an instrument called the Bemek Advanced Rock Tester (BRT) was developed in Sweden. With a total weight of approx. 35 kg, the BRT is portable and sells at a small fraction of the cost of a conventional testing machine. It is comprised of a small 65 KN loading frame with attachments for a variety of tests (see Table 1) , a hand operated hydraulic pump, an electronic balancing unit and a programmable microprocessor. The microprocessor is capable of storing data, performing arithmetic operation on, and printing signals from, a transducer and two strain gauges. A detailed description of the apparatus is given by G. Swan et al. (1). The proposed test strategy involves first a 3-point flexure test on a notched core specimen, followed by a 4-point flexure test on the separated specimen halves. Finally, point load and Brazilian tests can be carried out on the quarter parts of the original specimen. Thus specimen preparation is kept to a minimum. These and other perceived advantages have prompted the purchase of this machine and an evaluation of its suitability to provide data on mechanical properties of intact rock for numerical modelling and rock mechanics design at Noranda's underground mines. Details of its performance evaluation and experiences with the unit are discussed in the following sections. [ ] INITIAL OPERATING EXPERIENCE During the commissioning stage the BRT had, or developed, a series of problems, some of which seriously affected its operation. Below are some examples. Poor documentation was the most serious problem encountered. Confusing instructions for the 4-point bend test installation and its microprocessor programing, as well as poor and ambiguous information on the calculation of gauge factors, are some of the difficulties which had to be overcome. Meehan~cal problems occurred, including failure of the hydraulic pump, as well as electronic difficulties with the microprocessor. Other problems with the printer, requiring its replaceqent, were fortunately covered under warranty.

Jan 1, 1986

? World industrialization, increased urbanization, and population growth are driving a sustained demand for minerals, metals and coal. Energy demand is expected to increase significantly in the coming decades - placing even more emphasis on supply, security and environmental impact issues. ? Several countries are taking steps to nationalize their own resources thus safeguarding their supplies and reducing exports of natural resources. ? Understanding the future availability of critical minerals requires a global perspective. It is essential to know where deposits are located, their reserves and resources, the technologies necessary for production, and the costs of producing and transporting the products to consumers. ? As mining companies look to maintain or increase their operating capabilities and increase their mineral resource bases, the search for commodities expands beyond developed terrestrial regions of the world, to include marine resources. (Figure 1) Operating challenges in these locations include finding skilled workers, building infrastructure, improving recovery technologies and practicing sustainable development.

Jan 1, 2011

By Waclaw Trutwin

The idea of automatic or remote control of the mine ventilation process generally, and methane concentration particularly, attracts the attention of mining engineers more and more. The advantages of introducing mine ventilation control systems are breaking traditional reluctance. The change of attitude is not only because of the requirements of modern exploitation technology, but it is also due to the recent progress in development and successful introduction of reliable monitoring systems and actuators in the form of controlled ventilators and doors [1]; [2], [3], [4], [5], [6]. Many 'years of theoretical and experimental studies of the dynamics of mine ventilation processes created the needed base for a proper design of an automatic control system [7],[8],[9], [10]. From these studies must, however, be drawn a fundamental conclusion, which may be regarded as the motto of this paper: An automatic control system for mine ventilation ill-conditioned or improperly designed is capable of creating hazard situations in response to random disturbances, much more, severe in consequence than a traditional ventilation system without any automatic or remote control! This statement is easy to prove if the dynamic properties of the ventilation process are taken into consideration. The ventilation process, as a matter of fact, is described by non-linear equations, and it must be expected that the process has more than one state of equilibrium. In other words, in the ventilation process may exist not only one but also more than one steady-states of flow, of which some are stable and others unstable. In certain circumstances, there may be no steady-state at all, and the process will oscillate [8], [11] , [12] . The state of flow in a network tends towards a steady-state and the actual steady-state established will depend on the initial conditions or disturbances in flow (fire,. etc.), which steady-state from the total number that will be . We frequently observe jumps from one steady-state to another. Disturbances in flow conditions which may cause such transitions are events of random character, occurring very rarely. Concluding, it must be stressed that there has to be a control system adjusted to the ventilation process in order to avoid situations mentioned above. There is only one alternative available and suitable for examination or study of the dynamics of a given mine ventilation problem: either by continuous monitoring of the real process, or numerical simulation of the process using a mathematical model. The advantages of the second method are obvious. This method allows consideration of every possible case very quickly and cheaply in relation to the first method. The aim of the paper is to show again that the simulation of the mine ventilation process and particularly a methane concentration process, separately or combined together with a control system, are real possibilities. A simulation method requires precise specification of the problem under consideration. For example, if we intend to examine a methane-concentration control system, the following items have to be specified: - expected target function of the control system. - structure of the control system. - mathematical model of control system, including sensor system, data preparation system, controllers, decision routine, regulators, etc. - structure of mine ventilation network. - mathematical model of ventilation process, including air flow and methane concentration processes. - pattern of disturbances which may occur in the controlled process as well as initial conditions on a 'start-up' of the system. Using typical computer programs for numerical solution of equations in the mathematical model of the problem involved, we are able, within the adequacy of the model, to simulate every case specified by the disturbances and initial conditions. As a result of simulation, it is expected that the following parameters could be defined: - transient flow in the network. - transient state of methane concentration in working areas. - stability of flow and methane concent¬ration. - stability of the control system. - range of control. - efficiency of control, etc. It is obvious that simulation methods readily allow for modifications to existing systems such that desired results will be obtained. Also optimisation problems could be solved by use of the simulation methods. In order to illustrate these general thoughts, a brief presentation of a mathematical model of methane concentration and

Jan 1, 1980

By George Weinman

GEORGE WEINMAN: Our first group leader for the discussion, "Ups and Downs of Downsizing," wishes to remain anonymous. ANONYMOUS PRESENTER: When George and Jamie asked me to do this, I thought a while about what to say and went through several variations of what I’ll present today. I came up with the title "Ups and Downs of Downsizing." A lot of downsizing has occurred in all of our industries-mining in particular. While this downsizing has gone on there's no doubt that all of us produced more and more, probably with less and less people and less and less resources. But I contend that there's also a big downside associated with this. I disagree with a point made in the keynote presentation yesterday, the point being that vendors are bringing new technology to us. I can agree that the major changes associated with equipment and similar items are being brought to us by vendors. But I do contend that there's an awful lot that's getting away from us-especially if you factor in the integrated supply or the strategic alliance or the various and sundry related purchasing techniques. I contend that we are missing a lot of, let's call it, lesser technology; not major equipment changes, but different tools, different techniques for doing things, different left-handed widgets. The integrated suppliers, to some degree, are bringing this to us; but I am concerned about the small guy who comes up with a good idea but deals through integrated suppliers rather than having direct contact with plant people. They're probably going to go somewhere else and market their wares. That's what I'm hearing from a lot of smaller vendors. I also think that we are losing a lot of our knowledge base. Every time you shrink an organization somebody leaves. The bottom line: less people. When a person leaves-and I don't care who he or she is, be it the janitor who's cleaning the bathroom, the operator, the engineer-when that person leaves there's some knowledge that goes with that per- son. And sometimes that knowledge is quite valuable. I've worked more or less at the plant "low." I can't tell you how many excellent, viable projects have come from people who said, "Look here. There's a better way of doing this." And, you know, they were right. Now, maybe they didn't have the resources or the expertise to develop these ideas into full projects, but they had that basic idea. Someone may say, "Well, if we put a no. 6 skyhook here, so we can lift this particular pump without bringing a crane from 30 miles away ...." No. 6 skyhooks are a bit expensive, but what if we put together a little structural steel here or whatnot?

Jan 1, 1998

By L. G. Sobral, J. E. Hoffman, T. J. Keefe, A. J. Monhemius, O&apos

The kinetics of electrodeposition of gold from dilute solutions of alkaline KAu(CN)2 at different gold and free cyanide concentrations on a gold rotating disk electrode were investigated by use of a steady-state linear potential scan technique. The design and performance of a laboratory electrowinning cell with a reticulated nickel cathode, operating in the flow-through mode, for the removal of low levels of gold ions from aqueous cyanide media is described. During the batch recirculation of oxygen-free gold cyanide solutions, the gold concentration was reduced from 10 ppm to <0.5 ppm with current efficiencies of up to 80%. The influence of solution flow rate through the cathode and of the pore size of the reticulated nickel foam is discussed. The removal of gold ions from solutions of low ionic strength was also investigated.

Jan 1, 1993

By W. W. Vaughn

In the technique described and evaluated, detection of mercury is based on the principle of atomic absorption. An analog signal, produced when mercury vapor absorbs ultraviolet light, is converted to digital form and calibrated to mercury concentration. Interferences are eliminated by selectively trapping the mercury on gold. The lower limit of sensitivity, using a 1-gram sample, is 5 parts per billion. A model of the instrument mounted in a station wagon has been tested successfully in the field.

Jan 1, 1964

By Richard R. Klimpel

The author was the banquet speaker at the 48th Annual MPD meeting, sponsored by the SME Colorado Minerals Processing Section, May 14-16, 1998, in Colorado Springs, CO. Here are his remarks. It has been an exciting experience to have spent 34 years involved with the process of generating patented technology eventually leading to commercialization. In today&apos;s terminology, this process is called technology transfer. I have had the unusual experience of being involved doing basic research as an inventor while also being responsible for managing new product development and commercialization. In addition, I worked for 31 years before my retirement for a large research-oriented company, The Dow Chemical Co. In 1995, the company spent more than $1 billion dollars on research and development. The last three years of my career have been spent working with a research-oriented university, The University of Florida. And I have worked as a consultant helping several companies to optimize their products and processes. It is on this cumulative experience base that the preparation of this article is based.

Jan 1, 1998

By Jörg Weidemann, Peter W. Kuchar, Paul Burgwinkel

The West German Ruhrkohle AG and the engineering company BEDIA have developed an emission control system for diesel engines that is suitable for use in underground coal mining, consisting of a granular catalytic converter and a dry cooling system. Its first ever application was to a diesel mining locomotive. In the catalytic converter the exhaust gases pass over porous, platinum-covered ceramic balls in a double tube, oxidizing CO to CO2. Simultaneously, soot particles in the gases are subjected to afterburning. Laboratory tests carried out by BEDIA and at Aachen University of Technology showed that there was a reduction of over 80% in the CO content of the exhaust gases and over 30% in soot emission. The dry cooling system fulfills all the requirements demanded of exhaust cooling underground and does not have the disadvantages of conventional systems. It needs little maintenance, and it is light and compact. The most important components are a waterjacketed exhaust manifold, a tube and shell heat exchanger, a new type of flame arrestor in a stacked crimped ribbon design and a Venturi diluter. The system has its own thermostatically-controlled cooling circuit to keep the exhaust temperature between 120° C and 150° C, thus effectively preventing the tubes becoming blocked up.

Jan 1, 1989

By Nasri Munfah, Raymond E. Sandiford

"Superstorm Sandy (Sandy) created a storm surge that inundating many of the tunnels that pass beneath the Hudson and East Rivers. The tunnels are vital infrastructure links for the economy of New York City and the northeast region. The sea water, which contains highly reactive salts, caused significant damage to electrical and mechanical systems. In addition, the salt water inundation left corrosive precipitants on the tunnel linings and on and within electrical duck banks. After the salt water was evacuated from the tunnels, condition assessments were performed using a state of the art approach involving high resolution laser scanning, digital imaging, and thermal imaging. These scans were performed prior to hands on inspections. The damage assessment concluded that, although the tunnel structural linings were not damaged, the interior elements of the tunnels needed major rehabilitation to arrest the continual deterioration of the structures. This paper details the state of the art approach used for these tunnel inspections. INTRODUCTION On October 29, 2012 Super Storm Sandy flooded a large number of both transit and vehicular tunnels in the New York Metropolitan area. The region’s transportation network was severely disrupted. The storm damage is estimated to have been in excess of $30 billion, and with the tunnels out of service, the local economy was losing hundreds of millions in economic activity. Restoration of these tunnels was a very high priority and the resulting expedited restoration process did not always provide adequate time for comprehensive condition surveys. This resulted in many of these surveys being conducted after service restoration. Inspecting highly trafficked transit tunnels is challenging and the logistics of working in short night outages led to a rethinking of the conventional inspection approach. Traditionally, visual and tactile methods are first used to inspect tunnels and then quite often followed by LiDAR (Light Detection and Ranging) scanning and perhaps infra-red scanning. For multi-mile tunnels, the time required to visually map tunnel features can be quite extensive. By performing the scanning first and then performing the visual and tactile inspections, one is able to use the scan data to identify the specific areas that need detailed inspections. This approach was used quite successfully for a number of the NYC tunnels."

Jan 1, 2016

By Jack W. Eloranta, Michael J. T. Orobona, Peter R. VanDelinder

Ore blending for process optimization is becoming an increasing factor for managing cost and productivity. Economic mining and processing a very low value ore in an extremely competitive market results in constant cost-cummng initiatives. The inherent conflict between the lowest possible mining cost and the lowest possible milling cost is reviewed here in the context of blasting for autogenous mills. Iron ore blending focuses on a number of properties-liberation values, weight recovery and concentrate silica being the most important. Other chemical and metallurgical factors are also commonly controlled. Recent research has fueled an emerging interest in blending on physical ore properties as well. Fully autogenous mills rely on the large, competent fraction of crushed feed to act as grinding media. Previous test work indicated that Hibtac mills require specific amounts of 6- to 10-inch ore. High recirculating loads require a steady influx of large rock fragments. Blast designs, therefore, are presently characterized by wide patterns and low powder factors. Current efforts are aimed at improving mill throughput while reducing overall energy costs. Based on research and published case studies and the advent of optical measuring devices, Hibbing Taconite Company has embarked on a blast optimization program to identify optimum mill feed and to design blast fragmentation goals for each geological unit and each mining area. This paper outlines the preliminary findings of an ongoing, broad-based team effort which requires close cooperation of geologists, mine engineers, crushing and milling personnel. Three specific areas of investigation are reviewed: I) Historical relationships between powder factor and mill performance, 2) Blast fragmentation modeling using the Kuz-Ram model, and 3) Drill

Jan 1, 2004

By T. Yalcin

It is well recognized that machine type and machine characteristics play vital roles in the successful application of froth flotation in mineral processing. Since the early 1900s, a multitude of machine designs have been and are still being introduced in an attempt to improve flotation efficiency. Machines based on mechanical agitation have been the most dominant in industrial practice. However, in recent years there has been a growing interest in pneumatic flotation units because of their claimed simplicity, low cost, high throughput and good metallurgical performance. This work was carried out to assess the effectiveness of pneumatic flotation on a magnetite ore. The method was applied using a prototype pneumatic flotation device that utilized a suitable nozzle for bubble generation. Important variables of the process were examined and optimized, including the nozzle size, air flow rate and froth thickness. Further tests were conducted to determine the influence of frother dosage and to explore the improvements that could be made on concentrate grade and recovery by cleaning and scavenging. Under the best test conditions, an iron concentrate was obtained with a grade of 66.4% Fe and a recovery of 97.7%. Particularly, the recovery was superior in comparison to that of mechanical flotation. This was attributed to the ability of pneumatic flotation to create and maintain a relatively thick froth layer.

Jan 1, 2002

By Chee S. Theng

As the 2015 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2015 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 338. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME. Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2015 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-focus articles on gold processing, iron ore processing and coal processing. The 2015 Transactions consists of a total of 67 technical papers, encompassing all 22 papers published in 2015 in the Technical Papers Section of Mining Engineering (Vol. 67) and all 29 papers published in 2015 in Minerals & Metallurgical Processing (Vol. 32). Additionally, this volume contains 15 papers and one discussion that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2015 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2015

By George D. Roberts

Dams are constructed to retard the flow of water or debris; therefore natural forces are constantly at work to remove such obstructions. To circumvent nature and avoid expensive trouble with a dam requires thoughtful far-sighted planning, careful construction control and vigilant periodic inspections to detect and repair deterioration at its inception. Although the factuality of the foregoing statements is apparent, all too many have failed to consider them in the past as will many in the future. "The economic, but safe construction of dams calls for the highest order of technical knowledge, practical experience and sound judgment." (1)

Jan 1, 1967

By John H. White

As production of ground limestone increased our Company found it had an enviromental problem with limestone dust from our hammer mills. With the quarry and processing plant situated within 1 klm of a small township of 5000 people dust collection became essential. Regulations under the Clean Air Act 1972 also had to be complied with. Prior to this any demand for lime flour had been met by the use of a small drier and ball mill. Both expensive to operate. Dust emitting from the mills would amount to over 4000 tonnes per year. The cost savings were obvious. We had a better product which was essentially a by-product. Faced with a surplus of a very useful, but difficult product to handle we considered the possibility of disposing of it on the agricultural market.

Jan 1, 1982

By Yoshinori Shimada, Oleg Kotiaev, Hiroaki Sakamoto, Toshihiro Asakura, Naotoshi Yasuda, Norikazu Misaki, Masahiro Shinoda

"To ensure that trains run safely, the performance of railway civil engineering structures is checked by periodic inspections. General inspection method has merits and demerits, but none of them offers the combination of high accuracy and quick inspection. In an effort to resolve this problem, West Japan Railway Company, the Institute for Laser Technology and the Railway Technical Research Institute jointly developed a remote laser sensing system as an alternative to the impact acoustics method for detecting defective concrete elements in tunnel linings. The proposed remote laser sensing system has two lasers, one to apply an impact to the concrete surface and the other to measure the vibration of the concrete generated by the impact laser. The impact laser is a high-energy pulse laser that induces vibration in the concrete. The detection laser has a signal beam and a reference beam. The signal beam reflects on the concrete surface and goes into the dynamic hologram crystal. The reference beam diffracts in the dynamic hologram and enters the detection sensor with the signal beam. The vibration of the concrete surface can be measured to detect the movement of an interference pattern. A prototype of the remote laser sensing system was developed as shown in Figure1. A vibration and acoustic insulators are equipped to remove a noise generated from a maintenance car or electric generator in this system. The proposed laser remote sensing system and the detection algorithm were verified with the help of field test conducted in a tunnel on the Shinkansen. An impact test using hammering was applied to obtain the accurate response acceleration on the surface of the concrete before application of the proposed method. In this test, the result obtained from the proposed method has good agreement with that obtained from the impact test by hammering. Consequently, it is verified that the proposed method can be used as an alternative to the standard impact acoustics method."

Jan 1, 2016

By Chee S. Theng

As the 2017 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2017 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 342. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2017 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH), a special review article on Heap Leach Modeling, and articles from two Special Issues on Rare Earths. The 2017 Transactions consists of a total of 54 technical papers, encompassing all 21 papers published in 2017 in the Technical Papers Section of Mining Engineering (Vol. 69) and all 24 papers published in 2017 in Minerals & Metallurgical Processing (Vol. 34). Additionally, this volume contains 9 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our Publications staff. As the 2017 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2017

By Donald E. Dickie

At Sifto Canada&apos;s Goderich salt mine near Goderich, Ontario, the stress control method of mining was introduced to overcome increasing roof failure problems. After successful testing, the conventional room-and-pillar mining method was converted entirely to the stress control method. This conversion has successfully stabilized the ground, increasing the extracton ratio from 38% to 50%. At the same time, it reduced the ground control and rehabilitation cost by more than 80%. The success of the conversion is due to the quantitative technique of mine analysis that was developed to ensure that the conversion was safe and reliable. A finite element model of the ground was constructed to predict and validate the safety of the stress controlled mine opening. A system of in situ stress-property measurement instruments was developed to obtain input data for the computer model as well as to evaluate its output quantitatively with regard to time and location. History of roof problems Severe roof safety problems have been encountered at Goderich Mine since it opened in 1959. These problems continued into the 1980s. Following excavation, the roof strata started to deteriorate by slabbing. Even after roof rehabilitation, deterioration continued to progressively higher roof elevations, requiring repeated rehabilitation. The operational impact of these roof failures was severe, ranging from a considerable safety hazard to major production interruptions.

Jan 1, 1993

By Klaus Schönert

Experimental investigations of single particle and interparticle breakage show that the microprocess in mills demands an energy input between 1 J/g and 10 J/g, if particles below 100 pm have to be comminuted. A system analysis of grinding media and roller mills is given in respect to the energy supply to the microprocess and the influence of the back stream caused by the compression of the material inside the active volume. The back stream diminishes the probability for capturing the particles in very fine grinding processes. Some possibilities are discussed how to solve this problem.

Jan 1, 1989