Search Documents

By P. A. Meyer

The Tenmile Range is a north trending zone of high relief within the central Colorado porphyry-mineral belt, located between Leadville and Breckenridge. (Figure 1, the Index Map of the area surveyed.) The Climax mineralized zone is located at the southern end of the range on the northwest side of the Continental Divide. This portion of the total area surveyed will be discussed in detail today. A fixed wing aeromagnetic survey was flown over this range and mineralized zone in the fall of 1957. The survey was run as an experiment to see if a useful geophysical tool could be applied in the exploration for similar type deposits. The purpose of this paper is to describe the results of this survey and the approaches used to aid in the interpretation of the total intensity data.

Jan 1, 1968

By W. Baguley

There are many carbon-in-pulp and resin-in-pulp screening devices which are at present in use in the South African mining industry. Each one of these screens has been an improvement, from the very basic air cleaned and 'EPAC' types which were either circumferential or · diametrical launder screens, which were developed for C I P in the early 1980's, through to the more sophisticated LAP and Kambalda Screens. Each one of these screens not only increased the performance or throughput per square metre than its predecessor, but also addressed maintenance problems, wear, reliability and the ability to handle surge conditions, thereby preventing tank overflow. However, very little theory has been presented concerning, the flow of pulp through internal screens, carbon loss and screen wear rates. Almost all this information is based on empirical data. The NKM screen continued this trend and was able to offer flow rates in excess of 180 cubic metres per square metre of screen per hour and an average screen life of approximately six months. However, with increasing sophistication of the screen and the use of wedge wire as opposed to the normal woven wire, the mass was significantly increased and costs began to mount. Therefore, Mixtec undertook to develop a radically different screen, which incorporated many of the advantages of .the existing equipment and combined a few of its own.

Jan 1, 1992

By Qiong Wu, Li Guo, Qinghua Gu

BP neural network is a multilayer feedforward network trained by error back-propagation algorithm, which is one of the most widely used neural network models. However, BP neural network has exposed more and more shortcomings and deficiencies with the expansion of the application scope. In the prediction of ore quantity, BP neural network has the characteristics of slow convergence and easy to fall into local minimum point. In order to obtain the global optimal solution, and to improve the defects of BP neural network, this paper proposes combination optimization algorithm of genetic algorithm (GA) and BP neural network to improve the speed and accuracy of forecasting the main design flow chart and the analysis of the sort distinguish algorithm are offered, and then some problem in the design and debugging of the algorithm are discussed. On this basis, the GA-BP neural network model is constructed and applied to optimize the initial weights and threshold value of BP neural network. This model choices the floating point coding method to encode the connection weights and thresholds, and divides subjects into several populations. Through the introduction of selection, mutation, crossover, initial weight and other operators, making operational synergies between the various groups. This study selects 30 geological units, 8 quantitative variables (Pb, Zn, Cu, Mo, Si, Ni, Co, V) and 12 qualitative variables to carry out empirical analysis. Then the simulation of the algorithm is carried out in MATLAB and the parameters are analysed. By normalizing the input samples, 22 groups of observation data are used as the training data for prediction, and the latter 8 groups of observation data are used as the test data to be verified. The results show that when the ore quantity characteristics are not very significant, the model will produce prediction bias. But the improvement of the algorithm increases the efficiency of the function approach capacity of BP neural network and conquer the BP neural network system’s instability. It provides an auxiliary guide for ore prediction, which have higher reference value.

Jan 1, 2017

By R. Vogt, H. C. Mult, F. L. Wilke

INTRODUCTION At present, the capability of production planning software based on Linear Programming (LP) is still limited to the optimization of the single LP-run. This is due to the LP-model itself which cannot consider the interdependencies between individual LP- runs. With regard to planning of selective mining this limited way of optimization frequently leads to situations, where the remaining and accessible ore blocks do no longer allow to produce ROM-ore in the qualitative composition required by the ore processing plant. However, many of the aspects taken into consideration when setting up production plans built from mutually dependent LP-runs cannot be modelled in a system of linear equations. They are thus unsuited for treatment with LP and have to be taken care of by the planning engineer without any assistance by the system. The KBS currently under development is intended to assist the planning engineer in designing a production plan under special consideration of the combination of consecutive LP-runs and blending beds. It is not necessarily intended to find the optimum solution within a given planning situation which is, anyway, hard to determine due to the multitude of influences. The objective is rather to work out a good and - from the practical point of view - feasible production plan. The new aspect with respect to mine planning is the integration of expert knowledge and experiences via the KBS into the planning process in order to support the planning engineer. The planning system is being developed in close cooperation with an iron-ore open pit mine. COMPONENTS OF THE PLANNING SYSTEM The software is being developed on a workstation under UNIX and comprises the components LP, CAD-module and the KBS. The applied multi-goal LP-algorithm is an in-house development of the Department of Mining Engineering at Technical University Berlin. It was already successfully implemented within other mine planning programmes and was only slightly adapted to the specific needs of the present system. Within individual LP- runs it finds the optimum qualitative composition of ore production in the sense of the selected optimizing criterion and under the given restrictions: i.e. it determines tonnages to be mined from blocks in order to optimally meet the requirements of the ore pro- cessing plant. A CAD-module based on the commercial SURPAC package in combination with a simulation device is used to graphically depict the block model and progress of mining. Both LP-algorithm and CAD-package are integrated in the KBS. It has been decided to use the shell NEXPERT OBJECT as it is a hybrid system which supports both rule-based and object-oriented knowledge representation. MINE-MODEL AND LP-MODEL KBS have to be tailor-made for specific planning problems. Therefore, it had to be decided which specifications of the iron-ore mine should be represented in the model. As the limited possibilities of a university institute do not allow to develop a KBS for mine planning which is ready to use in industry, it was decided to concentrate on those characteristics that can be regarded as typical for iron-ore surface mines and that seemed to be suited for treatment with knowledge-based techniques. The following chapter summarizes the most important features of the mine model. The description of the requirements to the mine's sales products is followed by an outline of the applied LP-model. Mine model • The model of the mine as it is used for planning consists of • the block model of the deposit, • the mobile equipment, • stockpiles and blending bed and • the requirements to the sales products. The deposit is described by a block model which contains data on the chemical composition, LOI, grain size and tonnages. Grain size was included as it is important for the two sales products of the mine. Furthermore, it is known whichs blocks require and which don't require blasting; this is relevant to the assignment of loading equipment to individual blocks. The blocks are devided in three categories: • ore, which will directly be taken to the blending bed; • waste, which will be put on the waste dump; and • blocks which will be either transported to the blending bed, to stockpiles or to the waste dump depending on the specific planning situation. This decision is made during planning. Neighboring blocks are combined in mining areas to which the loading equipment is individually assigned. Mobile equipment comprises shovels and wheel-loaders as well as trucks. The characteristics of the loading equipment are important for their ability to load different blocks and for the permissible degree of their re-positioning etc. The mine disposes of a blending bed for homogenization of the production, of a waste dump, and of several stockpiles with different ore qualities. The requirement to make only limited use of the stockpiles for economic reasons is included in the KBS. According to long term planning two commercial products have to be produced, which differ both in grain size and qualitative composition (TABLE 1). Their mass-proportions in the blending bed have to be within a fixed range. Not considered in long term planning is the occasional need for lump ore, which occurs at very short notice and has to be produced in a "campaign-like" manner. This requires the total re-arrangement of all plans for on- coming blending beds and would therefore be ideally suited for

Jan 1, 1996

By Sii Smith-Gruner

Blasthole drilling by todays standards is not a mature operation. In most mining appli¬cations, the blasthole drill rig is the least understood piece of machinery. Draglines, mining shovels, and haulage trucks may have more charisma, but the entire mining process starts with the drilling of blastholes to facilitate removal of the overburden and/or the primary material being mined. There are two (2) principal drilling methods them being rotary and percussion. In certain situations, percussion drilling is the most practical method, but for most applications, rotary drilling using the rotary tricone bit is the common and accepted drilling technique. While the drilling rig is on the surface and quite visible to everyone, it is really the object at the end of the drill pipe, the tricone bit, that is doing the work and drilling the hole. The rig supplies power to the bit and air to clean the hole. In addition, it must be capable of providing certain other functions and should be properly outfitted to adequately support the rotary tricone bit.

Jan 1, 1988

Ever since A Decade of Digital Computing in the Minerals Industry was published in 1969, mining men have expressed the need for an additional reference on computer methods. It was felt such a volume should spell out the "how to" of computer applications in the solution of their problems. Computers in the minerals industry will be 20 years old when the 1979 SME Fall Meeting and the 16th International Symposium on the Application of Computers and Operations Research in the Mineral Industry (APCOM) take place jointly in Tucson, AZ. On such an occasion it was thought appropriate to publish an anniversary volume which reviewed current practices and projected what might prevail as computer methods for the future. Thus was born the idea to publish Computer Methods for the 80's. The first planning meeting for this volume took place in Las Vegas, NV, during the 1976 annual meeting of the American Institute of Mining, Metallurgical, and Petroleum Engineers. It quickly became evident that no single computer method existed to solve most mining problems; rather, mining computer methods are generally tailored to fit unique geologic, mining, and organizational conditions. Hence a format which included both the theory and practice for each of the computer applications was adopted for this volume.

Jan 1, 1979

By Gregory A. Hahn

Explorationists and engineers rarely speak the same language. Explorationists are not cognizant of the information that engineers require to make the appropriate choices and decisions. Engineers can- not "translate"geo1ogic parlance and data into information relevant to proper decision making. This often creates a physical and intellectual "rift" between engineers and geologists that inhibits a smooth transition to development. A transition team leader who is grounded in both disciplines can best facilitate integration and communications between the explorationists, who understand the intrinsic attributes of a given deposit, and the engineers, who have to design for extraction and beneficiation of an orebody.

Jan 1, 2001

By Ronald D. Hill

The occurrence of acid mine Drainage (AMD) with coal mining has been well documented. (1) Less documentation is available of its association with other types of mining, e.g., copper, gold, zinc, and sulfur. Yet there are many locations in the western states where acid mine drainage is as great a pollution problem as in Appalachia and in some cases, because of the high copper, zinc, and arsenic concentrations, they present an even more difficult problem. Until a few years ago, it was generally believed that the neutralization of acid mine drainage was uneconomical thus, AMD was allowed to discharge freely into our streams. However, the demand for good water finally dictated that the mining industry be included under pollution laws. In 1964 the Commonwealth of Pennsylvania passed a law requiring that all active mine discharges meet a discharge standard of pH 6-9, iron less than 7 mg/1, and the water must have a net alkalinity. Several other states now require active mines to treat AMD. In all but a few cases, lime neutralization, often in conjunction with aeration, has been the treatment method used. The high cost of lime as compared to limestone and the poor quality sludge, (slow settling, large volumes, and low solids content) has stimulated work in the utilization of limestone. This paper reports on the current state-of-the-art of limestone treatment of AMD.

Jan 1, 1970

By A. J. Lewis, P. J. Hutcheson, M. E. Robertson, P. A. Moir, K. M. Barfoot

With the content of gold and platinum in the vast majority of ore deposits typically averaging 6 parts per million and less, the accurate and precise measurement of these metals in samples of ore and mining process streams has proven very difficult to achieve by modem spectroscopic analytical techniques. Largely because no other technique has proven suitable, the basic fire assay process has become the accepted international standard for these metals. Fire assay, however, suffers a number of disadvan­tages in the modem, competitive, high technology, and increas­ingly environmentally aware world. It is a labour intensive technique that is difficult to automate, and requires high levels of skill to ensure accuracy and consistency of results. Potentially hazardous chemical reagents are employed, of which, lead, in particular, can be a serious source of contamination to both personnel and the environment if not effectively controlled. Other dangerous elements, such as mercury and arsenic, liberated in high energy furnace operations, are further sources of possible health and pollution hazards. n contrast, the energy dispersive K X-ray fluorescence (K­XRF) technique devised by K X Technology Ltd overcomes many of the technical constraints of conventional low energy X­ray analysis, and has the potential to revolutionise assay opera­tions in precious metal mining. The technology is simply automated, requires basic operator skills, uses no chemicals, consumes less than 20kW, and is capable of detecting gold and platinum to an accuracy of O .1 parts per million by mass. The new third generation design of AZTEC laboratory instrument, released in 1994, is the result of significant technical development. Capable of analysing over 1200 samples per day, and developed primarily for grade control sampling, its applica­tions have spread to gold ore accounting from on-line conveyor belt sampling; screening of exploration samples; measurement of gold in carbon granules for Carbon-in-Pulp process control; and for conducting rapid checks to support key managemen decisions. The economic, rapid, and non destructive analysis ofup to 80g of ore for large numbers of samples, reduces sampling and sub-sampling errors, and provides improved grade estimates for ore bodies. When interfaced to a LIMS, laboratory automation and cost-savings can be further enhanced. The AZTEC design is also being modified for the analysis of platinum. The GOLDSTREAM on-line analysis system is an important new application of K-XRF to the continuous monitoring of process streams in gold ( or platinum) plants and mills. Integrat­ing the technologies of K-XRF to measure total gold, and dissolved gold spectroscopy to measure gold in solution, the insoluble fraction of gold can be deduced, and the effectiveness of the extraction process determined. Slurries are sampled automatically from selected points of the plant and pumped to the system for analysis. The information produced forms the basis for plant control and optimisation.

Jan 1, 1995

By Donald L. King, Frank A. Baczek

Sedimentation-based equipment is used in applications where separation of solids from liquid by gravity settling is desired. If a concentrated solids slurry is desired, the equipment is designed to "thicken"; if a clear liquid is desired the equipment is designed to "clarify." Thickeners normally handle higher solids loading rates than clarifiers, which usually process feed slurries containing low concentrations of suspended solids. Thickeners are therefore designed for heavier-duty requirements, and clarifiers have extra features to ensure more complete suspended solids removal. Major components (Figure 1) that are common to all sedimentation-based equipment are: tank, drive-support structure, drive unit and lifting device, rake structure, feed well, and a means of overflow and underflow withdrawal. Specific features are designed interdependently after the overall separation approach is defined conceptually. This conceptual approach is usually based on past experience or evolves from sedimentation studies conducted on samples of the slurry to be handled. Because many variations and combinations of components are possible, the overall conceptual approach has a number of possible designs that will accomplish the desired results. The final choice is based on practicality, potential for minimizing upsets, and cost.

Jan 1, 1986

By T. W. Peterson

There are two approaches to developing a minicomputer based application for an industrial grinding circuit. Usually, the control program is coded and compilation-debugged on a large-scale scientific computing system or the minicomputer itself if the machine is available. Final debugging and testing must wait for installation and checkout of the entire minicomputer system. Two immediate disadvantages of this approach are the need to obtain, install and check out the hardware before the final debugging stages of program development can begin, and interference with normal mill operation during such final testing. This work reports on an alternative to the usual procedure. Here both compilation and execution bugs are eliminated from the application program before hardware installation by testing the control program against a reasonable dynamic simulation of the entire process. Thus, software development can be completed before the target mini is installed. Such off-line development requires a reasonably accurate mathematical model for the entire process system as well as a suitable simulation package for communication between the simulated environment and the minicomputer application program. Specific data describing the design configurations and dimensions of the mills, cyclones, sumps, pump characteristics and analog controller configuration were supplied by ANAMAX for a grinding division consisting of a rod mill followed by two ball mills in parallel. This information was used to set up a plausible model structure. Steady state ANAMAX data on particle size analysis at various points in the circuit and corresponding values of flow rates, pump speeds, sump heights and slurry densities were used for model parameterization. The preferred operating control strategy - "best grind at operator-set rod mill feed rate" - was set by ANAMAX. An inferential particle size analysis technique using the cyclone cluster as an on-line particle size sensor was used in a novel control strategy_ to achieve the stated objective. Two disturbances common in the ANAMAX circuits - rod mill scoop pluggage and shut down/start up of one of the ball mills - were studied in detail. This report out- lines the steps in system development and testing and the results obtained.

Jan 1, 1974

By R. W. Barbaro, J. M. Mutrnansky

This paper presents a nonlinear integer goal programming model that optimizes a mineral production schedule while considering the penalties and bonuses based on quality variations in the final product. It involves five coal quality goals plus a profit objective in its formulation and uses the weighting method of goal programming for a solution. The goals to be sought involve the sulfur, ash, heat content, moisture content, and ash softening temperature of the blended coal product. The model is linear in its handling of most of these goals but uses a piecewise linear integer formulation for the sulfur and heat content bonus and penalty schedule. The model is applicable to any mineral product blended from several different sources and subject to a varying price dependent on blended product quality or qualities. However, it seems to be most pertinent to optimizing production schedules for coal deliveries to power plants. Accordingly, the model is applied to a hypothetical coal production problem where multiple coal mines are operated to supply a final blended product to a power plant. In this example, the price paid for the coal is assumed to be a function of five of the most important coal qualities. The problem is solved as a direct function of the coal supply contract, thus removing the necessity of determining the weighting coefficients on a subjective basis.

Jan 1, 1987

By Carl P. Venzke

Mining lignite in the Gulf Coast often requires some interaction with shallow ground water system. Suggestions for determining ground water data and analysis requirements for regulatory compliance are given. Simple methods for estimating mine inflow seepage, ground water level declines, and changes in ground water chemistry, which may result from mining, are discussed. The mining of lignite often results in interaction with shallow ground water systems. An evaluation of the interaction is required as input to mine permitting and engineering. Your evaluation will proceed more smoothly and produce more meaningful results with some planning prior to performing your evaluation. The following are tips to consider in planning and carrying out a successful study.

Jan 1, 1982

By Patrick A. Ley

Maintaining, managing and manipulating large quantities of geologic data can be a very costly and time-consuming process. The use of computer-based methods can provide some relief to the problems of editing, displaying, and interpreting spatial geological data. ENCORE is a system designed specifically for coal orebody modeling and reserve esitmation where the geologic data is stored on a large mainframe computer and is accessed from a local work station for editing, manipulating, and producing various reports and high-quality engineering maps. The ENCORE system was designed for use by the geologist or mining engineer with little or no computer background and, additionally, it was designed to provide the geologist or mining engineer enough flexibility to be able to select the appropriate methodology for the orebody being analyzed. The various analysis tools incorporated into ENCORE can significantly increase the professional's productivity without burdening he or she with the need to understand the details of the internal computer language.

Jan 1, 1982

By [Miroslaw] M. Hajdasinsk

The identification of the real internal rates of return (IRR's) of a project is essential for its economic evaluation. The existing methods for the calculation of IRR's are both cumbersome and unreliable, mainly because of their inability to effectively isolate the real IRR's and incapability of discovering multiple IRR's of even multiplicity. In this paper, a concept of the 'cash flow pattern tree used for isolation of the real IRR's of a project is presented. This concept, combined with the Sturm procedure for counting the real distinct zeros of a polynomial within a specified interval, leads to the development of a method and computer program for isolation and calculation of the real IRR's of a project. The method examines whether or not real IRR's exist, and if they do, isolates them within bounded and narrow intervals in a mathematically founded way. The isolated IRR's, whether simple or multiple, are subsequently calculated either directly or by means of an appropriate approximation procedure. Numerical examples assist the development of the method and the corresponding computer algorithm. Because any Net Present Value treated as a function of interest rate can easily be transformed into a polynomial, the method presented also constitutes a method for finding the real zeros of a polynomial.

Jan 1, 1986

By T. H. Jones

Fall of ground is a leading source of worker injury and fatality indicating a persistent need for ground monitoring technology. The HRTMM is an experimental convergence monitor utilizing a digital camera and custom software to track the position of one or more lasers across the target. Apparent laser movement is proportional to target convergence. The HRTMM was installed in an underground mine near active operations to test its response to the mining environment. This included intense blasting vibration and mine fog. Results and potential of the new monitoring technology will be discussed.

Jan 1, 2008

By L. Alan Weakly

At a time when the US mining industry is struggling to emerge from a lengthy recession, the burden of new, unnecessary regulations could shorten the life of, or be fatal to many domestic mining companies. The possibility of new restrictions on the use of diesel equipment operating in underground mines is one example of unnecessary regulations. These could cause serious harm to the economic health of many mining companies. Whether future health-related Mine Safety and Health Administration (MSHA) regulations restricting the use of diesel equipment are unnecessary, depends on whether these restrictions are supported by fact or created in a political environment. The mining industry has benefited from the use of diesel equipment in underground metal-non-metal and coal mines for more than 50 years. Since first introduce to underground mines in the early 1940s, the use of diesel equipment has grown in numbers and size. During this time, the mining industry in America has achieved much higher productivity rates and improved safety. Although all these gains cannot be attributed to the greater use of diesel equipment, a high percentage can be. I began my professional mining ca¬reer in 1970 working in the Missouri lead mines. At that time, the use of diesel equipment was well established in metal-non-metal mines throughout the United States and many parts of the world. As director of mining research for St. Joe Minerals Corp. (now The Doe Run Co.), I was involved in research to improve mining productivity and safety. This involved investigating the better and safer use of existing or new mining methods, products, equipment and people. Within this group, diesel equipment had the single largest positive impact.

Jan 1, 1993

By B. Jensen, R. Davis, P. Golledge, A. D. S. Gillies, W. Urbanik Urbanik

A current program of research on the explosibility of coal dust/methane mixtures is described. During the study an explosion test chamber based on a novel design has been developed. This 20 litre open chamber uses a rotating drum concept for dust dispersion and infra-red sensors for dust concentration measurement. The chamber design allows different initiators to be tested while varying methane gas and coal dust concentrations. A new approach to the determination of coal dust concentration is included with a description of a dielectric dust probe. The measurement technique is based on the change in dielectric constant as the proportion of coal dust in air between probe capacitor plates increases or decreases. Characterization of coal dust samples is of vital importance. The particle size distribution, coal proximate analysis and elemental analysis were studied. Coal dust was sourced from airborne collected samples, settled dust from mine sources and seam channel samples crushed and sized. Explosibility test results indicate that a very low concentration of coal dust can form an explosible mixture when dispersed in methane concentration of just below five percent. With low temperature initiators, the coal dust lean limit concentration rises rapidly as the methane concentration is reduced. An accurate knowledge of the potential explosion hazards of coal dust and coal dust/methane mixture is necessary to establish safe operating conditions in underground mines. The research results outlined extend knowledge in this area.

Jan 1, 1989

By L. Zhou, D. Bahrami

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time and computer-power consuming, especially for a large-scale mine ventilation network. In this paper, a direct derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the direct derivative method were verified against the results from a traditional method. The direct derivative method has been proved to be reliable and accurate.

Mar 2, 2022

By William Highton

If the economic situation in the Western World evolves on a path similar to that of the past decade, then we Mining Engineers must accept that one of the major cost factors in the production of deep mined coal is going to be that of labour. Whilst not trying to over-simplify matters it does appear that one of the ways of maintaining acceptable coal costs is by obtaining more coal without increasing manpower. One such way could be an increase in the use of the retreat method of mining. The paper theorises and illustrates case studies to show that as the Mining Industry extends the use of Longwall retreat mining systems in coal seams where the risk of spontaneous combustion exists, then the use of bleeder entries should be questioned. In addition to the spontaneous combustion risk, bleeder entry systems where the ventilation flow is not fully controllable cannot be construed as a safe and reliable method of controlling high rates of methane emission. These two major aspects alone should be sufficient ground for Mining Engineers to re-consider the practice of using bleeder entries. An alternative "The Back Return System" appears to offer most of the advantages for controlling the environment, without the disadvantages of the other system.

Jan 1, 1980