Search Documents

By John A. Breslin

Control of radiation hazards in mines is only one of many goals of the Bureau of Mines. Radiation research is only a small part of the Bureau's mine health and safety research program. In this paper I will describe the mission and programs of the entire Bureau of Mines, with emphasis on the mine health and safety program of which our radiation research is a part. The radiation program and its results will be described in detail by other speakers during this symposium. The Bureau of Mines was established in 1910 and is one of a number of agencies within the Department of Interior. Our mission is given by the Organic Act of the Bureau of Mines, last revised in 1913, which still accurately describes our work today. The amended Organic Act (Public Law 62-386) gives the Bureau authority "... to conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment, and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources through the prevention of waste in the mining, quarrying, metallurgical, and other mineral industries; to inquire into the economic conditions affecting these industries..." Since 1913 at least 52 public laws bearing on Bureau responsibilities have come into force. However, our basic role is still unchanged, i.e. improving health conditions, and increasing safety and efficiency in the mineral industries. The two principal activities of the Bureau are Minerals Information and Analysis and Minerals Research. The Minerals Information and Analysis programs provide the data base and the analytical capability to support the development of effective national mineral policies. Data on the availability, production, and utilization of minerals are collected, interpreted, and analyzed for some 100 commodities. Resources of the most important commodities are evaluated to support policymaking that influences utilization of the Nation's existing and potential mineral supplies. The President's budget for the Mineral Information and Analysis programs in fiscal year 1982 is $34 million. The largest activity of the Bureau is Minerals Research, which is divided into three major programs: Mineral Resources Technology, Minerals Environmental Technology, and Minerals Health and Safety Technology. The principal goal of the Mineral Resources Technology program is to help provide technology to maintain an adequate supply of minerals for the United States. The budget requested by the President for this program in fiscal year 1982 is $41 million. The goal of the Minerals Environmental Technology Program is to create mining and mineral processing operations that are more compatible with the environment. The budget for this program in fiscal year 1982 is $12 million. The largest program of the Bureau is Minerals Health and Safety Technology, which has the goal of providing the technology to protect the health and safety of mine workers. The budget for health and safety research for fiscal year 1982 is $55 million. Our radiation research is part of the health and safety research program. The Bureau of Mines has done research to improve health and safety conditions in mines since it was established in 1910. The research expanded greatly following the passage of the Federal Coal Mine Health and Safety Act of 1969 (Public Law 91-173) and the Federal Mine Safety and Health Amendments Act of 1977 (Public Law 95-164). These acts provided for increased health and safety regulatory activities, but they also significantly increased the funding available for mine health and safety research by the Bureau of Mines. Funding for the Bureau's health and safety research grew from $12 million in 1970 to $60 million in 1981. The funding in 1982 will be somewhat lower than that for 1981. However, the health and safety program funding is still approximately 40 percent of the total budget of the Bureau of Mines. Of the health and safety budget, 22 percent is spent on research to control health hazards in mines, including radiation hazards, which has a budget in 1982 of approximately $1.1 million. Other mine health hazards which the Bureau is doing research to control include respirable mine dusts which cause black lung and silicosis; excessive noise; toxic gases from explosives and diesel emissions; and excessive heat in deep hot mines. The other 78 percent of the budget is spent on safety research to prevent death and injury to miners from such causes as roof falls, fires, explosions, and accidents involving mining equipment. Over the past decade the majority of the Bureau's health and safety research has been done through outside contracts with private industry and universities. Our policy has been to do some research inhouse to maintain the expertise of Bureau personnel. Contractors are used to do research for which the Bureau does not have the necessary personnel available. The percentage of the program being done by contract has been gradually declining for the past few years, and in 1982 the program will be divided evenly between inhouse and contract research. The inhouse research of the Bureau is done at the 10 research centers located throughout the country. Our radiation research is done at three research centers, Denver, Spokane and Pittsburgh, and by contractors whose work is monitored by project officers at these centers. There are three Federal agencies involved in mine health and safety. These are the Bureau of Mines, the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and

Jan 1, 1981

By John A. Lombardi

The solutions used in the heap biooxidative treatment of sulfidic refractory Au ores and concentrates generally load free mineral acid and metals and, in time, become bacteria activity inhibiting due to increased acid and/or metals concentrations. The metals­acid loaded, bacteria action inhibiting, solution must then be: (a) processed, prior to re-use, to reduce its metals and/or free acid mineral acid components to bacteria activity compatible levels; or (b) neutralized prior to discharge. The most common solution processing method to adjust acid-metals contents is liming to effect the precipitation of dissolved metals and neutralization of acid sufficient for solution discharge or re-use. The lime treated solution is high in suspended, colloidal precipitates and requires clarification before reuse. Most often the "bleedstream" of biooxidation solution that is lime treated is discharged and req­uisite volumes of fresh water added to the process inventory. Depending on the level of bacterial action in a heap and the acid consumption characteristics of the ore/concentrate being biooxi­dized, the bleedstream taken from the circulating, irrigation on­off, solution, can be large (e.g., 10%-20% and sometimes as much as 50% of the daily solution flow requires treatment-dis­charge). The lime charge for bleedstream treatment is commen­surately large and represents a major operating cost of the bioox­idation process. The patented HW Process Technologies (HWPT) Engineered Membrane Separation (EMS™) method is an alternative biooxi­dation bleedstream treatment method. EMS™ processing removes the multivalent base metals ions in an acid solution to a small volume EMS™ "concentrate" (typically 25% of the feed­stream volume). The EMS™ method coincidentally makes a "clean acid" EMS™ "permeate" (typically 75% of the feed­stream volume). In general, EMSTM processing enables 75% of the bleedstream volume to be recycled; allows up to 2/3 of the bleedstream acid to be recovered as a 10% solution; and delivers dissolved metals in a highly concentrated stream suited to a. metals recovery or b. reduced cost lime neutralization for a given metals precip­itation relative to full bleedstream neutralization (typically a 30% lime use savings). Implicit in the recovery of process water for re-use and reduced reagent addition requirement for metals precipitation is a significant reduction in wastewater-sludge dis­posal facility size.

Jan 1, 1998

By James Lonergan

This paper describes the application of the Graphics Assisted Under Ground Engineering (GAUGE) software to a 2-layered room and pillar hard rock mine. The graphics- assisted mine modeling and mine planning capabilities of GAUGE are demonstrated. The system uses polygons to model the room and pillar mine design and displays the model in plan view on the graphics screen,. The planning engineer interactively specifies areas to be mined in the medium or long term. The system calculates and accumulates tonnages and grades for the user-specified areas based on the layer being mined and the particular unit operation (drifting, widening or benching).

Jan 1, 1989

By A. M. Johnson, D. H. Carlson, D. L. Johnson, S. T. Bagley

A biologically assisted ferric iron leaching system was evaluated for in situ recovery of three copper sulfide oresfrorm northern Michigan. Laboratory scale bacterially assisted ferric sulfate leaching tests were run on the three ores. A T. ferrooxidans strain was found that could be adapted to copper in solutions at concentrations as high as 20 g/L. Column leaching of 4.5 to 2 mm (-4 +I0 mesh) material yielded extractions of 80-90% copper from one ore and 70 and 60% from the other ores. The highest copper extractions were from the Mount Bohemia ore deposits located in the Keweenaw Peninsula, which have fracture controlled chalcocite mineralization. The Bohemia ores are apparently well-suited for in situ solution mining.

Jan 1, 1987

By T. Tempel

In 1994 Newmont Gold Company commissioned a 2.5 Mt/a refractory gold ore roasting plant near Carlin Nevada. Many unique characteristics of this facility required use of specialized materials of construction in the areas of dry grinding, roasting, gas cleaning, and sulfuric acid production. Process conditions and design criteria that necessitated the use of special materials include; siliceous and abrasive ore, low roasting temperatures, gas streams with high concentrations of oxygen and sulfur, and stringent environmental regulations. Materials selected for use were ceramics, corrosion resistant steels, high temperature steels, and high temperature polymers, lead, polypropylene and low flammability PVC.

Jan 1, 1997

By Peter A. Gillett, Ian S. Clelland, J. G. S. Hynd

Today mine shaft and slope contracts include a greater amount of ancillary work such as level and pump stations, loading pockets, rotary and side dumps and connecting raises. This ancillary work requires the application of a number of construction methods often for short periods and often at short notice if the contractor is to maintain a profitable operation. In the next decade, the number of shafts that will be sunk by a boring method will outnumber those sunk by traditional methods. This will be particularly true of the deeper shafts where water problems are minimal. The increase of bored shaft work will not decrease the work completed by the shaft sinking contractor but it will change it. A greater emphasis will be placed on the speed of construction of station and other ancillary work. To meet this challenge the contractor requires full information on the ancillary work as well as the shaft work at an early date, preferably pre-bid. The two examples discussed in this paper illustrate the importance of early information. The two main factors of shaft ancillary work construction are sequence and ground support. This paper describes two examples completed recently by The Cementation Company of America Incorporated in Arizona. The first described is a Rotary Dump-Ore Pocket-Ore Pass complex and the second described is the excavation of the Main Station Level in a 2 Station-Loading Pocket-Ore Pass complex. CONSTRUCTION OF ROTARY DUMP, ORE POCKET AND PASS Introductory

Jan 1, 1976

By Ali Soltani, Scott Santti

The Gold Quarry Mine is a large scale open pit mine located 11.3 km (7 miles) north of Carlin, Nevada. The operation consists of an open pit mine, two milling facilities, a leach crushing plant, and three dump leach pads. Gold Quarry is operated by Newmont Gold Company, which is 90.1% owned by Newmont Mining Corporation, a Denver based company. The property is the largest of the three gold producing properties operated by Newmont Gold Company on the famous Carlin Trend. This paper will give a general overview of the Gold Quarry mining facilities and detail mine operating practices. Specifics on cost saving ideas being implemented and those under investigation will be discussed.

Jan 1, 1989

By Guy G. Jr. Granger

INTRODUCTION Due to the current depressed state of the mining industry, many mining companies have been forced to operate at less than maximum capacity. This paper will describe how the AMAX Henderson Molybdenum Mine and Mill near Empire and Parshall, Colorado respectively have utilized operations scheduling and budgeting to achieve production targets at minimum operating costs The AMAX Henderson Molybdenum Mine and Mill have been operating most recently at approximately sixty percent of maximum capacity. OPERATIONS SCHEDULING Production Targets. The production targets are tons, operating days, tons per opera- ting day, head grade, recovery, and pounds of molybdenum. One specific objective of operations scheduling is to meet the production target for pounds of molybdenum. Present market conditions dictate that production be adjusted to match sales of molybdenum. Over-production and creation of molybdenum inventories is unacceptable. In summary, the product ion target for pounds of molybdenum must be met, but not exceeded. Capacity. The AMAX Henderson Mill single stage open crushing circuit capacity is 48,000 dry short tons per day. The AMAX Henderson Mill single stage semi-autogenous primary grinding mill circuit capacity is 38,000 dry short tons per day. All other AMAX Henderson Mi 11 circuits such as rougher flotation, regrind, cleaner flotation, lead leach, filtering, drying and concentrate handling are sized to accommodate the 38,000 dry short tons per day and pro- ducts from same. The tailing delivery system is designed to accommodate tailing from a 38,000 dry short tons per day operation. Constraints. One mill production scheduling constraint is that the mill operating schedule must be the same as mine production, ore haulage and crushing. There is a total crushed ore stockpi1e storage capacity of 240,000 dry short tons. This breaks down to 60,000 dry short tons of crushed ore over the three reclaim pan feeders for each of the four primary grinding mill circuits. However, there is only approximately 10,000 dry short tons of live crushed ore available over the three reclaim pan feeders for each of the four primary grinding mill circuits. Dozers must be utilized to re- claim and push the other crushed ore. Primary grinding mill throughput is

Jan 1, 1986

By J. E. Gebhardt, P. E. Richardson

External control of the electrochemical potential of a bed of mineral particles was investigated by the US Bureau of Mines as a method for controlling particle interaction with organic collectors and, thus, flotation response. A cylindrically shaped, 200- to 300-g bed of sulfide mineral particles was used as the working electrode in an electrochemical-flotation cell. In a pH 9.2 sodium tetraborate buffer, chalcocite floated with ethylxanthate at applied potentials [=] - 0.25 V (versus the standard hydrogen electrode) ; pyrite floated at potentials [=] 0.15 V. Differential separation of a chalcocite-pyrite mineral mixture was obtained by controlling the potential, but the flotation response of the mixture did not follow the behavior predicted from measurements on the individual mineral beds. Chalcocite dissolution products had a deleterious effect on chalcocite-pyrite separation by activating pyrite so that it floated below the potential (~ 0.13 V) at which xanthate is oxidized to dixanthogen. A pyrite bed activated with a copper(II) sulfate solution exhibited a flotation response with a potential dependence between that of chalcocite and pyrite. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1988

By A. G. Naguib

In essence, any magnetic separator operates on the basis of imparting a preferential magnetic force on particles of higher magnetic susceptibility which are to be separated from particles of lower magnetic susceptibility. A certain amount of directional deviation to the particles takes place thus allowing for collecting each category of particles separately. The forces in action on particles in a wet magnetic separator of the established designs can be analyzed in a simple manner as shown in Figure 1.

Jan 1, 1972

By Judith A. Marks, Deane K. Smith, Jan M. Mutmansky, Maria Klimkiewicz

The mechanical mining of coal seams where roof, partings, and floor rock are extracted along with the coal often introduces large numbers of quartz particles into the mine atmosphere. This study concentrates on the quartz properties in situ and in the airborne dust to determine how they are released from the source rock and whether they are fractured by the mining machinery. Three mines using drum-type continuous miners from different geographic areas were sampled to provide a data base. The roof and floor rocks were primarily siltstones containing 5% to 25% quartz measured by the X-ray powder diffraction (XRPD) method. Much of the work presented here is based on the morphologies of the mineral grains determined by the scanning electron microscope (SEM). The study concentrated on particles of 0.2 to 10.0 µm and on particles containing > 75% Si. Mechanically-crushed quartz particles were also examined for comparison purposes. Particle shapes from the airborne samples suggested that fractured quartz particles were rare. Particle statistics also show that the average size of quartz particles in the airborne samples were similar to the average size of all particles. The conclusion is that very few quartz particles from the source rocks are fractured during mining due to their small initial size and the protection of the associated clays.

Jan 1, 1991

By Francisco J. Escandon V.

Numerous lead-zinc-barite-fluorite ore deposits, with simple mineralogy and roughly concordant with bedding, are found widely distributed all over the world, having been denominated and well described as "stratiform deposits" or "strata-bound ore bodies", not having any genetic relationship. During several years, its origin has been discussed, without getting to general agreement regarding the main mining districts of this type. Through studies made of large stratiform deposits in the United States, Europe and Russia, it has been found that there are, within this classification, syngenctic diagenetic and epigenetic ore bodies. During the Symposium about the genesis of the stratiform lead-zinc-fluorite-barite deposits, carried out in New York in 1966, Frank G. Snyder (1), presented an excellent analysis of the theories of the origin of these deposits and of the evaluation of the criteria regarding classification. As per his definitions (Table 1), "a deposit is syngenetic if formed by processes similar to and simultaneously with the enclosing rock, epigenetic if introduced into a pre-existing rock and a diagenetic origin implies deposition of metals with the host sediments but with recrystallization, rearrengement and limited migration".

Jan 1, 1974

By Ralph D. Daley, Kevin E. Redinger

The production of coal/water fuel (CWF), a highly loaded mixture of finely ground coal, water, and chemical additives, presents a unique opportunity for significant ash and sulfur reduction through physical coal cleaning. Froth flotation can be integrated with the staged, wet, fine grinding inherent in the CWF production process. A laboratory scale research program was conducted to demonstrate the feasibility of a flexible, integrated coal cleaning/CWF process flowsheet. Performance of the conceptual flowsheet was examined for two coals of CWF commercial interest, Upper Freeport and Pittsburgh seam coals, from central and southwestern Pennsylvania, respectively. Several multi-stage coal flotation and reverse flotation circuits were evaluated. CWF was produced from the cleaned coal in each case at similar solids loadings and viscosities as observed for the raw coal. However, the ash loading and SO2 emission potential for each CWF had been significantly reduced.

Jan 1, 1988

By E. Stone, R. Reagan

Risk of hand injury is very real for operators carrying out conventional bolting operations with power torque tools, reaction arms and backup wrenches. Bolting operations of this type are common today in the installation and maintenance of heavy mining machinery and equipment. Newer solutions have become available that have the potential to dramatically reduce the risk of hand injuries in mining applications. MINING APPLICATIONS Within the scope of mining operations, various types of equipment are used such as tunnel boring machines, bucket wheel excavators, draglines, material handlers, screens, pumps, crushers, continuous miners and longwall systems. Design of these machines typically includes larger diameter bolts for strength and durability. Due to rugged use all machines require frequent maintenance and service which requires the use of heavy industrial bolting tools and methods. Those engaged in bolting operations include technicians working for end-users, equipment manufacturers, general contractors and others who provide services in mining operations. Most all personnel involved with these activities are engaged with use of high power bolting tools and procedures. Training is essential to raise the awareness of bolting safety and to avoid accidents. However improved bolting tools and procedures can play an even more significant role in further improving the safety of all those engaged with bolting in the mining industry. SAFETY CONCERNS Professionals working in the mining industry are constantly looking for ways to further reduce risk to health and safety. Bolting operations which are fundamental to service and maintenance of mining equipment are often overlooked as a potential area for improvement. Several areas of bolting operations offer potential for improvement in safety and avoiding accidents during equipment maintenance. This paper addresses the safety concerns associated with reaction arms and backup wrenches in conventional bolting applications (Figure 1).

Jan 1, 2019

By Arthur S. Radtke

The structural setting of disseminated-replacement gold deposits of the Carlin-type and other aspects of their genesis are closely related to events which took place during the evolution of the Basin and Range province. The deposits formed as a result. of chemical and physical processes which took place at shallow depths in the roots of hot spring systems at moderate temperatures (about 200°C) and low pressures (about 25 bars) (Radtke and Dickson, 1974). Locations of Carlin-type gold deposits in the Basin and Range province are shown in Figure 1. Most of the block-faulted mountain ranges in the Great Basin formed by tectonic activity that happened since Miocene time, although faulting in some places probably began in Eocene to Oligocene time (Hamilton and Myers, 1966). The Carlin-type deposits are spatially related to Basin and Range-type faults: Many deposits, such as Getchell, Pinson, Preble, and Cortez, occur along the flanks of ranges, while other deposits, including Carlin (Radtke, 1974) occur within the ranges in areas characterized by crosscutting and intersecting high-angle or Basin and Range-type faults. The association of the ore deposits with Basin and Range-type faults is evidence that ore deposition is young, Miocene or later. The steep, high-angle faults played three roles: first, they provided deep channels for upward-flowing solutions; second, in preparing the rocks for fluid penetration by brecciation and general rock dislocation; and third, they moved sedimentary carbonate rocks, favorable for ore deposition, from deep levels to near-surface positions where the physico-chemical conditions were more suitable for the deposition of ore.

Jan 1, 1976

By Robert D. Talvensaari

It is indeed an honor for White Pine, as a member of the copper mining industry, to participate in this Rapid Excavation Conference. Although our presentation, as the title indicates, is not a success story, we foresee, through our experience, future application of boring machines and rapid excavation equipment in the hard rock mining industry. One might ask what a copper mining company would be doing with boring machines and why the gamble on a high-cost, capital investment for a relatively untried application. Perhaps a little background on the White Pine mine and its geology will explain our daring and speculative motives. THE WHITE PINE MINE The White Pine Copper Company, a wholly-owned subsidiary of Copper Range Company, operates a mine, mill and smelter at White Pine, Michigan in the western Upper Peninsula approximately 6 miles due south of Lake Superior. We employ approximately 3,000 people from the surrounding area and mine approximately 25,500 tons of low grade (1%) copper ore per day. The orebody is contained within several distinct sedimentary horizons that comprise the lower 20 feet of a Precambrian formation known as the Nonesuch Shale. Numerous articles and reports have described many aspects of the White Pine operation and the geology. I will brief you only on that criteria which precipitated our interest in rapid excavation equipment and techniques, specifically, boring machines. Mineralogical and optical studies have demonstrated that the siltstones, sandstone and shale beds all contain relatively barren and discrete particles of quartz (25%), feldspar and mica, bonded with

Jan 1, 1974

By Carl G. Schwenk

Rusk County is located in the northwestern portion of the state of Wisconsin, roughly 130 miles east of Minneapolis (Figure 1). The topography is generally flat with dairy farming the principal activity. Forest and swamp lands are common, as well as pasture and cultivated ground. Rusk County falls near the southern terminus of the Precambrian Shield and is covered by a thick layer of glacial drift. Outcrops are quite rare, but the few available exposures indicate that the subsurface is comprised of steeply dipping metamorphosed volcanics and sediments of Early Proterozoic age. A thin section of flatlying Cambrian sandstone is sometimes found directly under the glacial till. The depth to Precambrian basement has been recorded to be as great as 150 feet beneath the surface.

Jan 1, 1976

By George A. Desborough, David L. Fey, Stanley E. Church

About 100 mine-waste dumps from past metal exploration and mining in Colorado and Montana were sampled using surficial-sampling methods for laboratory studies of the minus-2-mm fraction. In the laboratory, the composite samples were split into l00g samples that were leached to assess their acid-generation potential and associated release of potentially toxic metals that may degrade water quality in the headwaters of the Animas River watershed in Colorado and the Boulder River watershed in Montana. Two leach methods were studied: a passive leach using de-ionized water, and a more aggressive leach following the EPA-1312 method. The resulting pH values of the leachates using both methods are comparable. The concentrations of sulfate and several, but not all, dissolved or water-soluble metals are higher in the EPA-1312 leachates than in the passive leachates; however, the overall trends of the data are very similar. The passive leach method is less labor intensive and may be more representative of the natural weathering process occurring on the mine-waste dumps, simulating the natural precipitation and snowmelt. Three chemical characteristics of mine wastes studied here provide a relative ranking of mine-waste dumps for the purpose of determining priority for removal or remediation. These characteristics are: net acid production (NAP), sum of dissolved toxic metals (?As+Cd+Cu+Pb+Zn), and dissolved iron in leachates. Ranking can be done evaluating plots of NAP versus the sum of dissolved toxic metals, and NAP versus dissolved iron. These two plots serve as a basis for relative ranking of polymetallic-vein and acid-sulfate mine wastes studied. This ranking scheme may apply to mine wastes from production of other deposit types in other watersheds.

Jan 1, 2000

By Joseph E. Schiller

As part of the Bureau of Mines research on identification of asbestos fibers, a method was discovered for removing asbestos fibers from water. This report describes this process and its theory of operation. The surface charge of amphibole minerals in potable water was found to be negative, and in common with most other silicate minerals, the isoelectric point of amphibole asbestos fibers lies in the pH range 4 to 6. Magnesia is one of the rare oxides with a high isoelectric point of about 11. The surface of magnesium oxide will, therefore, be positively charged in water at pH 6 to 6, while the electric charge an. amphibole asbestos fibers is negative. Because of the electrical attraction of these oppositely charged solids, it was possible to remove negatively charged asbestos fibers from water by percolating water that contained suspended-asbestos through a porous bed of magnesium oxide particles. A bed of 100/200-mesh MgO was added to a glass tube with a cotton plug. Aqusous suspensions of 1 to 10 ppm cummingtonite asbestos (amosite), crocidolite, and chrysotile were percolated through this porous plug of MgO. Even though chrysotile is positively charged below pH 11, MgO is an effective filter medium for removing it. The highly basic MgO appears to cause the chrysotile to flocculate and attach to particles within the bed. Scanning electron photomicrographs indicated that essentially complete removal of the fibers from water was accomplished. Other materials tested as contact filter media and found to be ineffective or only partially effective were sand, calcite, carbon, diatomaceous earth, and cellulose. Acidic alumina collected amphibole fibers but not chrysotile fibers.

Jan 1, 1980

By Fulian He, Jianhang Chen, Shoubao Zhang

"Fully grouted rock bolts have been used in mining industry for many years. Significant research has been conducted to evaluate the load transfer behavior of fully grouted rock bolts with experimental programs. However, compared with that, less work has been conducted with analytical modelling. Therefore, in this paper, the authors used an analytical model to study the load transfer behavior of fully grouted rock bolts. To confirm the credibility of this analytical model, an in-situ pull-out test was used to validate this model. There was a close match between the experimental result and the analytical result. Following this, a parametric study was conducted with this analytical model. The influence of coefficients, Young’s modulus of the rock bolt and the diameter of the rock bolt on the load transfer performance of rock bolts were studied. Furthermore, the load distribution along the fully grouted rock bolt was analytically studied. The results show that the axial load in the rock bolt decayed from the loaded end to the free end independent of the pull-out load. However, the trend of the load distribution curve was influenced by the pull-out load. This paper was beneficial to better understand the load transfer mechanism of fully grouted rock bolts.INTRODUCTIONRock bolts have been used in the mining industry for a long time. They are used as the reinforcement tendons to keep the stability of openings in underground mining and the slope in open-pit mining. Furthermore, rock bolts are commonly used not only in the mining engineering, but also in civil engineering (Thompson, Villaescusa, and Windsor, 2012).The rock bolt is a tendon which can be a rod or a cable inserted into a borehole drilled in rock masses or soils. Traditionally, the material of rock bolts was steel. However, engineering practices showed that the steel rock bolts can be easily corroded by the moist environment in underground mines. Next, Fiber Reinforced Polymer (FRP) was used to manufacture rock bolts, which are termed as FRP rock bolts. Experimental results proved that the FRP rock bolts can effectively reinforce the surrounding rock masses without being corroded (Wang et al., 2018)."

Jan 1, 2019