Search Documents

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time- dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct- shear tests on mudstone overcored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that the risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2002

By Jerome F. Machamer

Ninety percent of manganese is used as an alloying element in steel. Smaller amounts are used in dry-cell batteries, in aluminum and bronze alloys, and many other uses. The element has several oxidation states, and oxidation-reduction reactions control its chemical behavior. Manganese, in primary minerals such as rhodochrosite, rhodonite, and braunite, is in a divalent oxidation state, and manganese in secondary minerals, such as pyrolusite and cryptomelane, is in a quadrivalent state. Virtually all manganese ore production comes from three types of sedimentary manganese deposits. First, lenticular beds of manganese carbonate or carbonate-silicate rock in Early Precambrian volcano-sedimentary complexes in South America and Africa have been major sources of manganese ore. Second, laterally extensive beds of mangano-silicate and manganiferous carbonate minerals in certain banded iron formations are major sources of commercial ore and constitute the largest resource of manganese. Finally, manganese accumulations deposited in marginal to epicontinental basins are the largest source of current manganese ore production. Residual deposits resulting from the destructive weathering of rocks with a low manganese content have been, but are no longer, important sources of manganese ore. Most deposits have been altered to some extent by super- gene oxidative processes, and are economic because of that alteration. Outcrops of manganese ores are invariably oxidized and can be very deceiving as to the character of the underlying material. Nearshore facies of epicontinental basins, and nearshore age-equivalents of metalliferous black shales are among the targets for new manganese exploration. Very high-grade manganese occurs in sedimentary deposits altered by metamorphic and metasomatic processes.

Jan 1, 2001

By Lei Chen, Michael L. Free, Ravindra Bhide

The incorporation of particles into metal matrix materials is important to many technologically important areas. Particles that are incorporated into a metal matrix have a significant effect upon the properties of the resulting composite. Proper selection of particles and incorporation densities can lead to optimal composite properties that can be modified as needed for various applications. This paper discusses the parameters that affect the particle incorporation density in electrodeposited metal matrix composite coatings as well as a deterministic model that can be used to predict the effects of such parameters on particle incorporation density.

Jan 1, 2003

By Barry J. Hansen, Ruston A. Ford

Production of mine backfill from the tailings produced in a proposed Crandon concentrator is described. A process has been developed capable of producing suitable fill for the mining method selected for the Crandon orebody. It maximizes the placement of pyrite underground as fill and segregates tailings into pyrite and nonsulfide fractions. To determine the suitability and engineering characteristics of the backfill product for use underground, laboratory and physical stope simulation model testing was conducted. The results of the testing and the application of those results to the design of the backfill system ultimately affecting mine geometry and subsequent mine production will be presented.

Jan 1, 1981

By D. K. Sitler

Continuing advancements in manufactured diamond materials as used in rock cutting tools have created a new generation of high production tools for mining. This paper reviews the three major manufactured diamond product types available in the mining industry as supplied by General Electric Co., Specialty Materials Dept., and examines the ways these materials are used. As an integral part of this examination, the economic impact of manufactured diamond tools is evaluuted. Time and again, one will find that the premium price for these tools is economically justified when compared to traditional tools.

Jan 1, 1988

By John W. Wilson

Every operation connected with the working of a deep-level mine has, to a greater or lesser extent, a direct bearing on the costs of production, and hence, profitability of the mine. If adequate mine planning is not done in the early stages in the life of a mine, considerable expenditure can result from the cost of maintaining mine service tunnels, production delays in stopes caused by poor strata control, distortion of fittings in hoisting shafts, rockbursts and so on. In fact, the optimum profitability of a deep-level, hard-rock mine can only be achieved if the layout of the shaft systems, ore passes, tunnels, stoping areas and other underground excavations are designed to withstand or accommodate the rock stress conditions that will be created by mining operations. In South Africa where the deepest mines in the world are located, access to the underground workings of most deep-level gold mines is via vertical shaft systems and a network of tunnels connecting the shaft systems to the stoping areas. In current practice, there are two basic methods of extracting the gold-bearing reef,* namely, the scattered stoping method and the longwall stoping method. The choice of the stoping method is governed largely by the anticipated gold distribution and payability of the reef in the area, the geological conditions, the degree and complexity of faulting and dyke intrusions, the depth at which the gold-bearing reef is to be mined and the inclination and width of the reef. The longwall system was first introduced at the East 717 Rand Proprietary Mines Limited in 1942 in an effort to combat the rockburst hazard which appeared to increase with increase in depth. This mining method became standard practice on that mine for stoping operations 700 ft. below the surface. Since that date, several deep mines on the Central Rand, East Rand and West Wits gold mining areas have adopted this method.

Jan 1, 1977

By L. Xu, R. Bhaskar

While a NIOSH accepted procedure exists for determination of quartz in the respirable dust samples from coal mines, no specific procedure has been defined for quartz determination in bulk samples. In this study, the effect of particle size on the estimation of quartz using the infrared technique was evaluated. Several laboratory tests were performed to determine the dependence of the infrared absorbance peak height on the different sizes of quartz particles. The significant dependence observed between quartz particle size and the measured peak height indicates the potential for erroneous interpretation of the quartz in bulk samples depending on how the samples are prepared. A procedure to reduce the effect of size in the determination of the quartz content is suggested.

Jan 1, 1994

By I. Iwasaki

Rest potential and linear potential sweep techniques were used to study the cathodic-polarization processes on chalcopyrite, simulating chalcopyrite short-circuited with grinding media in a wet grinding mill. Microflotation tests were carried out to investigate the effect of cathodic polarization on the collectorless flotation of chalcopyrite. It was observed that collectorless flotation of a cathodically polarized chalcopyrite sample could he obtained when oxygen was used for aeration, but not if nitrogen was used. A mechanism for the role that oxygen plays in the collectorless flotation of cathodically polarized chalcopyrite is discussed.

Jan 1, 1999

By C. W. Benjamin

The paper covers the development of an efficient, "state-of-the-art" design approach encapsulating extensive research and development by Gulf on soft loading, low impact, zero spillage transfer chutes. The development, which interacts and interfaces the comprehensive methodologies for transfer chute design, allows Gulf to deliver detailed designs within 8-24 hours rather than the norm which is weeks or months. Outputs include 3D models of completed transfers and support structures along with rendered 3D representations of the design which can be fully manipulated around all axis in 3D.

Jan 1, 2000

By L. A. Panek

A new pillar strength formula is presented. It incorporates a function [IF] of size and shape that takes into account the size-shape interaction effect as well as the enhanced strength exhibited by wide pillars. Existing pillar formulas, lacking these capabilities, are not suitable for extrapolating small-specimen test results to mine-pillar sizes and shapes. Interpreting compressive strength test results as function of [Y] reveals wide-pillar behavior in much old test data. Model relationships are discussed, along with their scaling implications.

Jan 1, 1995

By Silvia Misk, Cristina Araújo, João Felipe Costa, Roberto Rolo

Linear estimation methods are widely used for resource evaluation. Among the existing linear estimation methods, ordinary Kriging (OK) was accepted as the best estimator to determine the average ore grade of each block. However, OK is inadequate for modeling small blocks in relation to data spacing, resulting in over-smoothed models. In this study, the results of the recoverable resource from the short-term model are compared to estimated models generated by the traditional method, i.e., OK, and non-linear methods. The conclusion is that non-linear methods improve the accuracy and precision of the long-term model when compared to the model generated by OK.

Jun 25, 2023

By J. R. Mattern

The engineering geology of the Rio Tinto Borax Boron Mine creates challenges in providing practical slope design recommendations to mine planning engineers. Low strength sedimentary units interbedded with very low strength lakebed clays surround the orebody. Faulting has offset and juxtaposed these units into variably adverse orientations, while groundwater is compartmentalized both vertically and horizontally within fault blocks. A collective program of geologic data collection, geomechanical strength testing, geologic modeling, slope depressurization, confirmation of underground stope locations, and documentation of slope behavior provides vital information for design investigations and sensitivities. Analysis results lead to risk assessments and operational procedures that add value to the business by optimizing slope configurations and minimizing risk.

Jan 1, 2004

By J. P. Nairn, C. M. McCulloch

More and more underground mining is being conducted using the long wall method. Likewise, many new surface mines use area or mountaintop removal methods. These methods can have a significant impact on surface and ground water resources. The overall study of the effects on surface and ground water from mining is referred to as the probable hydrologic consequences (PHC) determination of mining and reclamation. Collection and interpretation of information concerning ground water and surface water quality and quantity, as well as detailed geologic analysis, is required to adequately define the impacts of mining. This paper discusses the present day requirements and methodology of preparing a PHC for a large mining operation in the eastern coalfields.

Jan 1, 1997

By Jan M. Mutmansky, David R. Kalasky

Computer simulation continues to be one of the most successful analytical applications of computers in the mining and mineral processing industries throughout the world. Through simulation, managers and engineers can explore the impact of new technologies, equipment designs, plans and operating strategies to improve their operations. It is not uncommon for a single simulation application to provide a quick payback of analysis expenses (within weeks or months) yielding long-term financial and operational dividends. The paper will present a summary of the types of software systems that are available for use on PCs and other computer systems. Support software for curve fitting, statistical analysis, and optimization of simulation models will also be presented. Methods of leveraging simulation efforts through networking and coupling of software systems will be discussed. Finally, the trends in simulation in the mineral industries will be analyzed. Areas of strength and weakness of simulation will be discussed along with the usefulness of commercial general-purpose and custom-writ- ten simulation packages. The future possibilities for simulation in the mineral industries will be outlined and predictions on trends for the future will be presented.

Jan 1, 1996

By Waclaw Trutwin, Stanislaw Wasilewski

Application of computer-based systems for ventilation process monitoring makes it possible to widen the system functions with those connected with long-term data analysis. It allows the mine ventilation engineer to carry out necessary preventive actions. In future the wide application of computers and sophisticated expert systems together with automation equipment (like remotely controlled regulators and fans) will allow to gradually introduce minewide systems for air flow control. To achieve this goal research work is carried out using data from a mine ventilation monitoring system and methods of computer analysis of time series. With the use of digital filtering the measuring signal spectrum has been divided into three subranges components of which are important with regard to various needs of mine ventilation staff as well as to monitoring and control system functions.

Jan 1, 1991

By Van Zyl Brink

A longwall-based coal mine in Australia, referred to in this paper as AusMine Colliery, experienced windblasts resulting from goaf falls. Windblasts were the cause of serious injuries and threatened the continued operation of the mine. A microseismic early warning system was installed and a significant success rate in providing early warning of large roof instability resulting in high velocity windblasts, has been achieved. Early warning of goafing is accepted as an operational tool on the mine. Severe demands are placed on the operator in terms of 'real time' interpretation. The development of an expert system allowed for a probabilistic approach to achieve automatic alarms. This paper will quantify the success, failure and false alarm rates achieved by manual operation and automatic expert system-based decisions making, respectively.

Jan 1, 2002

By James S. Redpath

"The ways of the world be many and most of the ways be tried, you follow in the footsteps of others till you come to the great divide". These words, written by Robert Service a long time ago, come to mind when I think of our original attitude upon entering into a contract with the International Nickel Company to sink the deepest shaft in the world outside of the Union of South Africa. This shaft was to be sunk to a depth of 7,137 feet from surface, and while it was recognized by all concerned to be a somewhat unusual undertaking in our part of the world, the fact that quite a few shafts had already been sunk to this depth in South Africa probably gave us the feeling that we were following in the footsteps of others. In retrospect, because this shaft was being sunk under entirely different conditions than those existing in South Africa, we were in fact venturing into an entirely new area of endeavour without properly recognizing this fact. It has occurred to me that others considering a similar type of job could benefit from our experience, especially in an assessment of the risks involved and how they compare to those encountered in an ordinary shaft. For comparison purposes, I would define an ordinary shaft as being sunk to a depth of 5,000 ft or less, and a deep shaft as one being sunk to a depth of between 5,000 ft and 8,000 ft. The sinking of the Creighton No. 9 Shaft has been de-

Jan 1, 1997

By F. E. Heuze, R. N. Nilson, R. J. Shaffer, R. P. Swif

As part of the Unconventional Gas Program at the Lawrence Livermore National Laboratory, we are developing a model that allows for time-dependent tracking of the fluid front and flow pressures during the quasi-static or dynamic fracturing of jointed rocks. Application of the model is directed towards both short fast fractures (as in tailored pulse loading) and long hydraulically induced fractures (massive hydraulic fracturing). The thrust of this research is to determine crack extension characteristics due to specific joint systems and fluid properties and to correlate pumping records with crack behavior in jointed systems.

Jan 1, 1986

By J. C. Yingling, G. T. Lineberry

A control system for reducing peak loads on mine conveyor networks is proposed. The system involves continuous monitoring of flows into the conveyor network and section feeders with variable discharge capability. The control strategy uses differences in material transit times from various production units to the transfer points in the network to forecast load levels that will he intersected by the discharge of the controlled feeders over future time intervals. Feeder setpoint adjustments are made to prevent excessive peaks in the combined flows at the transfer points, while maintaining adequate feeder through flow to avoid production bottlenecks. Simulation studies suggest that the control strategy would be very effective in reducing capacity requirements of gathering belts.

Jan 1, 1993

By S. G. Hardcastle, Akbar Sheikh

In Canadian underground uranium mines, bacterial leaching is being increasingly applied to low-grade ore reserves. At Denison Mines Limited uranium operations, old stopes are used as leaching vessels; these contain a leaching muck pile brought down by drilling and blasting from the back which contained a low-grade reef. The bacteria used require atmospheric oxygen to oxidize the pyritic ore. A study was initiated to evaluate the ventilation, including oxygen supply, specifically, of flood leaching stopes during their rest period. The method of ventilation investigated was a single ended compressed air system which feeds airlines laid under the muckpile and carried through the inlet pressure bulkhead. The air delivery system was tested for post- blast integrity with a sulphur hexafluoride, SF6, tracer gas technique. This was injected into the intake compressed air line and collected at the stope's borehole exhaust in grab-sampling bags. The samples were analyzed with a laboratory gas chromatograph and results provided information on the stope's airflow, average residence time, overall clearance time, volume of the airpath and the airflow distribution. The borehole exhaust was monitored by anemometer and psychrometer and indicated that the psychrometric conditions in the stope were independent of the area's ambient climate. Evaluation of the exhaust's standard gaseous composition showed the oxygen consumption of the bacteria to be independent of the investigated flow range. Field derived results are compared with computer models, theoretical predictions and laboratory investigations.

Jan 1, 1987