Search Documents

By D. Armour, E. R. Bauer, D. R. Zuchelli, T. M. Durr, E. R. Reeves

A team of noise specialists from the National Institute for Occupational Safety and Health (NIOSH), Mine Safety and Health Administration (MSHA), and Joy Manufacturing attempted to evaluate an engineering noise control on a Joy longwall stageloader. The team developed and executed a test plan to evaluate the noise attenuation of the engineering control in an underground coal-mining environment. An evaluation of the long-term noise effects and durability of the engineering control were also a focus of the research effort. Pre- and postcontrol measurements consisting of a combination of worker dosimetry and task observations, tape recordings, and sound level measurements were used to evaluate the engineering control. A description of the engineering noise control, pre- and post-control sound level measurements, and an evaluation of control success is presented. In the end, no evaluation was possible due to mining practices, miner task variations, and inconclusive data.

Jan 1, 2005

By Robert C. Dunne, Maurice E. Freeman, Denis S. Yan

A laboratory tower mill was used to investigate the effect of some variables on the power requirements of a plant mill. The grinding laws were tested for fine grinding and Charles' law and Rittinger's law found to be most closely satisfy the experimental data. The effects of ball size, ball charge mass and media type were investigated. The screw speed was altered to control the power input as required. The results indicate that changes in these variables will change the grinding kinetics but in terms of the grinding efficiency they have no effect on the size-energy relationship. The main factor in the specific energy efficiency is the transfer of the input energy to the charge by variation of the agitation mechanism. The efficiency of a tumbling ball mill and a pin stirred mill were tested for comparison.

Jan 1, 1995

By R. R. Rollins

Conventional methods of controlling abandoned mine fires include: loading out, inundation, fire barriers, flushing, and surface sealing. This paper describes a proposed fire-control technique utilizing a new explosive fragmentation method. An impervious barrier is created by using explosive energy and strategic emplacement in boreholes drilled from the surface. Blast round design, average fragment size, and impermeability of the fragmentation barrier are discussed. This barrier, created by the blasted floor rock, could also be used to fill in the open space in abandoned mines for subsidence prevention or control.

Jan 1, 1989

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risks associated with the design of mine waste-management facilities. These experiences show that the technical and managerial challenges of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur in developed and developing countries is indeed re¬markable and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailings storage facilities are, in many cases, more demanding than those of conventional water dams because seepage of fluids that contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 2000

By P. C. Thakur

The history of coal mining in the United States of America and the rest of the world is replete with mine explosions and consequent loss of lives. Serious efforts in the USA to recover methane prior to mining and post mining started about forty years ago. CONSOL Energy Inc. and government agencies, e.g., the erstwhile US Bureau of Mines developed several techniques of methane drainage, such as in-mine horizontal drilling, vertical gob wells, hydrofracing of vertical wells and horizontal drilling from surface. With the current technology, thirty to sixty percent of total methane emissions from a mine can be captured making the mines much safer and more productive. Drained methane is often marketed to defray the cost of methane drainage. This paper is an anthology of these developments and describes how coalbed methane, which used to be a bane, has become a boon for the coalmining industry.

Jan 1, 2003

By Y. C. Lo

Grinding process optimization is an exciting new tool for maximizing the performance of existing mineral processing plants. This paper discusses the methodology of optimization which involves plant sampling, pilot tests, modeling, computer simulation and plant verification. The methodology developed emphasizes the interactions among operating variables and design options. Two example applications demonstrate that AG and SAG optimization provides the basis to increase grinding throughput up to 10 percent. This sys- tem optimization technology has been proven to be very cost effective for grinding plant performance improvement.

Jan 1, 1998

By L. John Minnick

Current developments in using lime and limestone slurries to remove sulfur oxide gases from the stacks of coal- and oil-burning furnaces have established an important need for treatment systems which include adequate disposal of resulting waste materials. The paper briefly outlines the classes of scrubbers which are using lime and limestone and describes the characteristics of the by-product material being produced. Some discussion is also included relating to methods of disposal of the scrubber underflow. Since coal-burning plants also produce fly ash as a waste material, one system developed by the author's company combines this material with the sulfur oxide by-products. The mixture is processed in a manner which converts the waste products into usable materials with acceptable structural and environmental properties. Recent interest in protection of ground waters from heavy-metal leachates has made the fly ash-sulfur oxide system an acceptable means of disposal, because the conversion products have very low permeability and adequately encapsulate soluble salts within the hardened mass. Although only limited information is available on the types and chemical requirements of limestone used in these processes, a few guidelines are presented to indicate the range of materials that can be used with good results.

Jan 1, 1974

By David M. Spatz

Team, as defined by Katzenbach and Smith (1993), is a small number of people with complementary skills who are committed to a common purpose, performance goals and approach for which they hold themselves mutually accountable. As the mining industry searches for new ore discoveries increasingly under post-mineral cover, the process of mineral exploration has taken us from prospector to geologist to multidisciplined explorer to multi-disciplinary team. Multidisciplinary exploration techniques have improved in terms of sensitivities and penetration and more than ever before each technique requires specialists with appropriate training and skills to process data and interpret results. To produce a quality product, specialists must collaborate openly and honestly in an atmosphere where the collective result takes into account the knowledge and expertise of each individual and the relationships between all pertinent data sets.

Jan 1, 1998

The need for geological control in orebody estimation and modelling is self- evident to geologists and mining engineers engaged in practical day-to-day estimation. It is only fairly recently, however, that attempts have been made to incorporate explicitly such requirements into published accounts of geostatistical estimation; see, for example, Dowd and Scott (1982, 19841, Rendu and Readdy (1982), Dagbert et al. (1984), Dowd (1984), Benest and Winter (1984). In practice, many geological controls in automatic or semi-automatic estimation and modelling are essentially geometrical controls. The aim of this paper is to present two techniques for geological/geometrical control. Whilst the applications are new, neither technique is entirely original and both have been adapted from other fields and sources. Both techniques are, in some sense, types of estimators and/or interpolators of shapes. The first is a method for fitting spline surfaces to control orebody boundary estimation and to unroll orebodies. The second is an application of Minkowski addition to interpolate shapes such as orebody outlines or stope boundaries and to control estimations.

Jan 1, 1986

By G. Karahalios

Industrial minerals always play an important part in the technological growth of a country. The extraction and trading of industrial minerals continues to expand, but the industry is now subject to stricter environmental guidelines. This paper presents the current status and growth potential of industrial mineral exploitation in the southeastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, the Former Yugoslav Republic of Macedonia, Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. Annual production figures per country are presented for 1992-1998. These figures are compared to each other, and, where applicable, they are compared to world production figures. The marketing of industrial minerals to Europe and other regions of the world and the effects of such trade on the local economies are also evaluated when such data are available.

Jan 1, 2000

By Alexander Filimonov, Yury Bloshteyn

The development of a high-efficiency control system for mine ventilation is a complicated scientific and engineering problem. As a result of high-costs and difficult conditions involved in experiments for the development and investigation of mine ventilation systems, simulation is a critical task in cost reduction and productivity. The paper presents the description of a universal simulation model for controlled aerodynamic processes in an Underground ventilation Network (UVN). The high-efficiency programming tool to design and investigate mine ventilation control systems (MVCS) is also suggested.

Jan 1, 1991

By R. S. Conti, L. L. Chasko

To deal with an unexpected event such as fire, prevention and preparedness are important elements in an underground mine's strategic plan. The purpose is to prevent afire before it initiates and to be prepared to deal with it when it does occur. This paper highlights a technology that may be used by the mining workforce to minimize such occurrences. It discusses thermal imaging cameras and their many applications to detect equipment failures or hot spots before they develop into afire. It also evaluates the feasibility of using thermal imaging cameras for emergency responders to assist them during exploration, rescue and fire fighting efforts. These thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, thus making it easier to locate heated areas and missing or trapped personnel.

Jan 1, 2003

A new separator, known as the HydroFloat cell, was developed to overcome the limitations of traditional flotation cells in recovering coarse particles. The HydroFloat cell separates particles based on differences in mass after the selective attachment of air bubbles to the hydrophobic component of the feed stream. Proof-of-concept testing, utilizing phosphate matrix, heavy mineral sands and anthracite slag, indicated that significant improvements in separation efficiency can be achieved using this air-assisted teeter-bed system. Based on the encouraging laboratory results, a pilot-scale HydroFloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the +35-mesh plant feed can be increased by snore than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the +16-mesh particles in the HydroFloat concentrate. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 2002

By M. Rosenshine, R. W. Barbaro

This paper presents a cyclic queueing model that evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumption of exponentially distributed service times and steady state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1988

By Song Jiang, Xianzhi Tan, Minjie Lian

"The ground water heat pump system lades underground hot water which can be heated or cooled by heat exchanger in water source heat pump air conditioner. This system replaces the model of heating of air-conditioning by refrigerator and boiler. In this paper, the formation conditions of hot water energy in Shan Dong are analyzed in order to achieve the purpose of energy conservation and emissions reduction by taking full advantage of water resources such as water pouring and return water of beatification during the productive process of underground metal mine. In order to analyze the issue better, the paper points out some ways and methods for geothermal water often used in underground metal mine. This paper also presents the advantages of the technology of water source heat pump that is applied into underground metal mine. Here is a case study of comprehensive utilization of water source in a certain underground metal mine in Ji Ning. This mine, according to its own actual situation, designs heat pump heat exchange system which is used for indoor heating of buildings and bath for staff. It turns out that the system can save 23% water per year, cut down 3.303 million KW electric energy, and reduce 4160t emission of carbon dioxide. It is concluded that the technology of water source heat pump has broad application prospects in underground metal mine. Therefore, the results show that it is an ideal way to change the present structure of cooling and heating source in metal mine.Introduction In recent years, overuse of fossil fuels has posed a grave threat onto the environment, which makes renewable energy a more important status in energy structure. Development and utilization of renewable energy has become an important direction. Water source heat pump technology is to use solar energy stored in water as cold/heat source to convert energy. Currently, this technology has been widely used in some advanced countries. However, due to facers of implementation technology and component costs, there is still a gap in water source heat pump technology between China and these advanced countries. According to (Blum et al 2011) that after in-depth study, water source heat pump technology has developed rapidly in China recently, and the gap is gradually reduced. Groundwater source heat pump system as a kind of high efficiency, energy-saving and environmentally friendly technology in recent years, more and more get the people's attention. At the same time, its practical application has also been rapid development. Based on (Ni et al 2015) that According to the relevant departments of the prediction, the technology will become the 21st century the most efficient heating and cooling technology."

Jan 1, 2017

By John S. F. Dunlop

One of the more difficult problems frequently facing geologists and mining engineers is that of estimating the ore reserves of mineral deposits. Cost conscious mining operations invariably require an accurate knowledge of tonnage and grade for both short and long term planning. A case study is presented, showing how a classical frequency distribution was fitted to a population of drillhole assays. Using these results, a grade- tonnage curve is derived using the Lasky expressions, and the results discussed. A geostatistical analysis is then presented. First, variograms are drawn, models fitted to them and analyses made of drift and anisotropy. Second, simple block kriging is carried out and the results plotted on large 1000 scale plans, suitable for overlay with routine .mine plans. Kriging results are verified using two independent techniques: random kriging on a regular grid and inverse distance weighting. Finally an attempt is made to optimize the drilling grid, and to fully tabulate the total computer running costs for the work described.

Jan 1, 1979

By D. C. Wilder

Deformations during heating and cooling of three drifts in granitic rock were influenced by the presence of faults and shear zones. Thermal deformations were significantly larger in sheared and faulted zones than where the rock was jointed. but neither sheared nor faulted. Furthermore. thermal deformations in faulted or sheared rock were not significantly recovered during subsequent cooling thus a permament deformation remained. This inelastic response is in contrast with elastic behavior identified in unfaulted and unsheared rock segments. A companion paper (Butkovich and Patrick, 1986a) indicates that deformations in un- sheared or unfaulted rock were effectively modeled as an elastic response. We conclude that permanent deformations occurred in fractures with crushed minerals and fracture filling or gouge materials. Potential mechanisms for this permanent deformation are asperity re-adjustments during thermal deformations. micro-shearing, asperity crushing and crushing of the secondary fracture filling minerals. Additionally, modulus differences in sheared or faulted rock as compared to more intact rock would result in greater deformations in response to the same thermal loads.

Jan 1, 1986

The objective of this study is to classify ore and waste in a selected mine. The support vector machine, was used for the classification purpose, is applied to a zinc ore body in a skarn deposit located in the central region of the Peruvian Andes. The input parameters used for the model are spatial coordinates and the lithological information of the ore body. The input data was divided into training and testing data sets and the performance of the model was tested using the testing data set. The results show that more than 76% of the data could be properly classified by this method. The ore waste maps of the deposit was then developed using SVM model. From the result it was observed that a comparatively very few number of cells classified as ore. The ore is concentrated in small lodes at the middle of the volume of study, and not uniformly distributed throughout the study area. The lithological map of the deposit was also constructed as it was used as an input parameter for the SVM model. The indicator kriging was used for generation of lithological map of the ore body. Key word: Ore waste classification, Support vector machine, Indicator kriging, Confusion matrix.

Jan 1, 2008

By F. F. Aplan, V. Choudhry

This investigation is an exploratory study to evaluate a large number of potential pyrite depressants for use during coal flotation. Subsequently, the more promising reagents can be evaluated in detail. Several reagent categories (such as alkalis, lime, oxidizing agents, reducing agents, specific inorganic ions and dispersants) that were found to be effective pyrite depressants are discussed here. Other pyrite depressants will be discussed in Parts II and III.

Jan 1, 1993

By Hiroyuki Kawata, Toshiyuki Ueno, Mikio Yamazaki

INTRODUCTION For the construction of several kinds of structures which pass through under railways, we have recently developed an effective and new tunnel construction method, aiming at more secure train operation during the construction as well as the rationalization in the construction works for such structures. Most important in carrying out the construction works for the structures under railways is how to maintain the safe operation of trains. For such construction works, temporary supporting structures and supplemental works have been often applied, for which high cost and long period for the construction have been required. While, this new tunnel construction method has the feature that it is capable of constructing definitive structures for various purposes, which, at the same time, acts as the temporary supporting members for protection of railways. Therefore, this method is now drawing much attention in that higher safety of train operation, low construction cost, and shorter construction period are accomplished, minimizing the period required for slackening the train speed during the construction works.

Jan 1, 1979