Search Documents

By Yong-ping Wu

Based on the rules of strata behavior and the characteristics of rock movement, the elementary problems of using fully mechanized coal mining techniques in steeply dipping coal seams are described. A model of the "surrounding-support-rock" relationship is made. The support systems stability during fully mechanized mining of steeply dipping coal seams is studied. Then, a practical engineering example of the fully mechanized mining of a steeply dipping seam is presented. The seam used in the example is in the Lushuidong colliery, which is administrated by Huaying Mining Bureau, Sichuan Province.

Jan 1, 2003

By Robert W. Wheeler, Richard G. Ames, Robert B. Reger

Introduction The use of diesel engines as an alternate power source in US underground coal mines has been a controversial step towards more efficent mining practices. Three areas of potential benefit are foreseen. First, diesel-powered mining equipment is believed to be more efficient, resulting in less occupational risk for any given amount of production. Second, diesels are believed to pose fewer intrinsic hazards, especially those related to fires and ignition of combustibles. Finally, several other health and safety advantages are foreseen for diesel units. Each of these issues will be discussed separately. Diesel Efficiency Proponents of the use of underground diesel-powered mining equipment point to increased production efficiency due to greater maneuverability, speed, power, and payload (Bradbury, 1973; Jorgensen, 1982; Ogden, 1978; Wenberg, 1979; Olsen, 1980). Units most suitable for diesel power include LHD vehicles, shuttle cars, personnel carriers, and maintenance vehicles. Estimates of increased efficiency vary from 60%-300% and more (Wenberg, 1979). Increased diesel mining efficiency is usually viewed as making it practical to mine lower grade seams. Diesel units can also operate over a wider range of floor pitches and distances than electrically-powered units, thus allowing mining of seams with special mining problems (Olsen, 1980). Diesel application is not a universal substitute for electrical power. For example, continuous miners are unlikely diesel candidates. Reduced Intrinsic Hazards Proponents of diesel use have pointed to the increased safety potential due to a reduction in electrocutions, arcs, burns, underground cable fires, and methane ignition (Ogden, 1978). Diesel units are frequently employed in maintenance activities for lifting and moving, and for coal cleanup. Thus the case is made that diesel use, by making powered operations more conveniently available, reduces the incidence of lower back injuries and related causes for days lost due to disability (Olsen, 1980). Several other issues relating to diesel safety have also been suggested. Diesel units can continue operation even during power outages allowing, for example, personnel evacuation. The maneuverability of diesel units make them particularly attractive in difficult physical conditions, such as long haulage from the face to the belt and in areas where water is deep. The case for diesel use focuses heavily on the potential for a "per worker" reduction in accidents, or a reduction in the severity of accidents. Since accidents are a major part of the health impact of mining, a reduction in accidents and resulting injuries would make a major contribution to the health of coal miners. Opposition to Diesel Use Opposition to the use of underground diesel mining equipment in the US seems to have started with the United Mine Workers of America. Some opposition to US diesel use has been based on a widely publicized 1976 letter from NIOSH to Mine Enforcement and Safety Administration administrator Robert Barrett (NIOSH, 1982). In essence, this letter warned that while insufficient evidence existed as to diesel effects on underground coal miners, NIOSH had concerns based on prior knowledge of separate diesel exhaust constituents and the potential for interaction between these constituents and coal mine dust. Current opposition to underground diesel use has focused on respiratory health effects related to diesel emissions, particularly nitrogen dioxide (NO,), carbon monoxide (CO), and particulate content (Barrett, 1982). Through

Jan 4, 1983

In late 1993, Inco Ltd. completed a $600-million environmental improvement project at its Sudbury, Ontario operations -the largest single environmental project ever undertaken by a Canadian corporation. Efficient new facilities and innovative technologies installed during the course of the project have also significantly improved Inco's productivity and competitiveness. In early May 1994, a panel of 18 Inco authors contributed to a Technical Forum, "Environmental Programs at Sudbury," presented at the 96th Annual General Meeting of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) in Toronto. Their papers have been published in CIM's Toronto `94 Proceedings Volume, pp. 62-77. The following report draws primarily on discussions of Inco's milling and smelting operations published in the Proceedings Volume. The Proceedings Volume also includes papers on the acid and oxygen plants and on engineering, construction and commissioning of the project. The 222-page Proceedings Volume is available from CIM, $C27 plus shipping. To order, contact: V. Ward, CIM, Xerox Tower, 1210-3400 de Maisonneuve Blvd W, Montreal, Quebec, Canada H3Z 3B8; phone 514-939-2710, fax 514-939-2714. Lane White, Publisher.

Jan 1, 1994

By N. I. Jayaraman

Dust scrubbers on continuous miners are steadily gaining in popularity. Recent US Bureau of Mines research on scrubbers is reviewed, with emphasis on development of a new type of water-powered scrubber that can he retrofitted to existing miners; comparison of scrubber effectiveness with blowing and exhaust line ventilation; and improving the quartz dust collection of flooded-bed panels.

Jan 1, 1990

By L. P. Meade

The need to feed an established talc mill from a crude ore source located closer to the mill prompted the 1986 drilling of a previously mapped, talc-carbonate deposit. This talc-bearing rock had never been considered a potential source of crude talc ore because of the high carbonate content and other deleterious minerals observed in outcrops. Selective mining, in-pit grade control and creative processing have allowed this deposit to be developed into an ore body. By definition, an ore body has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by ore tenor.

Jan 1, 1994

By Sylvain Duchesne, Claude Bazin, Robert Grant

Grinding simulators are now widely available to assist in the selection of circuit operating conditions or flowsheet designs that yield a given product size distribution. These simulators do not inform of the impact of the grinding product size distribution on subsequent flotation stages. This paper presents a method to predict the effect of fineness of grind on a flotation bank operation. Application of the method is illustrated with data from two Canadian concentrators.

Jan 1, 1995

By Lothar Baumann, Wilhelm Knickmeyer

In mechanized roadheading predominantly two methods of rock breakage are applied at present: the cutting method by means of picks and the cutting/crushing method by means of roller cutters. Both systems meanwhile reached a high degree of technical development and consequently show very few possibilities of further improvement. While application of hard-metal picks is limited by rock hardness, the roller cutters require a high specific thrust, and, accordingly, heavy carrier systems. Roller-cutter equipped tunneling machines are therefore only cost-effective in hard-coal mining if the high investments for transport and assembly are justified by a corresponding length of road to be headed. The limit for acceptable cost-effectiveness is at present a minimum heading length of approximately 3 km. In order to improve the specific cutting performance of roller cutters by activation, Bergbau-Forschung carried out a research project sponsored by the Commission of the European Communities and the provincial government of

Jan 1, 1981

By Paul A. Lahti

Independence Mining Company, Inc. (IMC) has for the past several years processed refractory gold ores at its Jerritt Canyon operation near Elko, Nevada. The ore is typical of those of the Carlin Trend and is refractory due to physical encapsulation of gold in carbon, pyrite, and arsenopyrite. It is also "preg robbing" due to the contained organic carbon that acts as a gold adsorber. Refractory ores require some form of pretreatment before cyanidation to enable economical recovery of gold. The metallurgical facility at Jerritt Canyon is unique in that it consists of two distinct pretreatment methods for the recovery of gold: a chemical process utilizing chlorine and a pyro-metal­lurgical process employing oxidative roasting. This paper pro­vides a comparison of the two methods highlighting flow sheets, pretreatment operation detail, performance comparisons, and pertinent environmental data.

Jan 1, 1996

By Ahmed M. Nofal

This article reviews some important characteristics of the known Egyptian phosphate deposits, such as mining conditions, transport criteria, quality of products affecting their export markets and utilisation in fertilizers industry. Special attention will be given to the newly discovered large deposit of Abu-Tartur with some billion tons of ore reserves. A big project is now under implementation on Abu-Tartur deposit where the long-wall method of underground mining will be applied and a flow sheet of beneficiation will be in operation including a particular feature nontraditional in phosphate processing: high-intensity magnetic separation to eliminate dolomite impurities. Comparison with some international phosphates will be tried in order to trace the situation of Egyptian phosphates in the world market.

Jan 1, 1993

By Robert J. Timko, Lincoln Derick

This work is a follow-up to previous research that attempted to predict the location of spontaneous heating episodes in underground coal mine pillars. The objective of the original work was to see if the data obtained by commonly used detection methods could accurately predict spontaneous combustion episodes in coal pillars. Data accumulation during the study was enhanced when a spontaneously generated fire occurred within one of the pillars being examined. The fire provided researchers with realistic data that could be used to determine if fire prediction was possible. Results from the initial study found that the atmospheric status equations that were used provided little advance notice that combustion would occur where it did. This study reevaluated the accumulated data by applying it to recently developed equations and compared these results with previously obtained information to determine if a combination of these techniques could more effectively predict impending combustion.

Jan 1, 1995

By Xia Guangxiang, R. Y. Wan, Yang Hanlin, M. C. Fuerstenau

The mechanism and kinetics of pretreatment on pyritic gold concentrate with the catalytic oxidation acid leach (COAL) process were studied in the temperature range of 80-100°C and oxygen pressure range of 230-1013 kPa, with sodium lignosulfonate (SL) and mixed medium of sulfuric acid (11 g/[ ]) and nitric acid (5.5 g/ [ ]). The results show that nitric acid acts as a catalyst, the surfactant changes the hydro-phobicity of resulting elemental sulfur to favor the oxidation of pyrite, and the oxidation-determining step would be the chemical reaction between nitric acid and pyrite. When about 80% of pyrite contained in the concentrate is oxidized, the gold cyanidation extraction exceeds 95 % . The nitric acid in solution can be recycled and used again.

Jan 1, 1993

By S. Kelebek, S. O. Fekete

The flotation process developed at Falconbridge laboratories utilizes sulphur dioxide and diethylenetriamine (DETA) reagent combination in the depression of pyrrhotite to allow its separation from pentlandite and chalcopyrite. DETA by itself has failed to produce flotation selectivity with samples from plant and pilot plant streams which showed relatively high redox potentials. However, DETA was found to function effectively on laboratory-generated samples under certain conditions. The results of poor depression are in keeping with thermodynamic calculations which indicate that in the presence of sufficient xanthate and DETA, the formation of ferric dihydroxy xanthate and dixanthogen is possible under oxidizing conditions. The use of sulphur dioxide alone has also resulted in a rather poor depression of pyrrhotite. However, the combined use of these reagents has resulted in an efficient and consistent separation of pyrhotite from pentlandite and chalcopyrite. Various aspects of this selective flotation system are presented along with a discussion on possible operating mechanisms.

Jan 1, 1995

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equipment, blasting, or water infusion. To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in.- diam). The techniques in detail are somewhat complex and subject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1990

By C. M. Brown

Common operating philosophies and objectives of mining and mineral process operations are discussed. Key information required to effectively monitor operations is reviewed in conjunction with the impact of external variables such as commodity price changes on strategies adopted.

Jan 1, 1991

By F. Seymour

A dynamic programming algorithm is presented that takes a series of nested phases, a fixed mining-rate schedule and a fixed plant-production-capacity schedule, and, from these, finds the mining and cutoff grade sequence that maximizes the net present value. This tool allows the mining engineer to quickly look at project sensitivity to various production capacities, commodity prices and costs. A description of the algorithm is given along with examples of how it has been used at Newmont Gold.

Jan 1, 1996

By W. P. Stroud, R. S. Dennen

A ground penetrating synthetic pulse radar system has been used by the US Bureau of Mines to probe into a coal pillar to locate hidden structures or anomalies. Direct matrix inversion was used to obtain a velocity image of the interior of the pillar. The reconstructed image showed the existence and location of a relatively low velocity material within the pillar. Core samples were taken from the pillar in a region surrounding the low velocity material. Analysis of the cores showed the presence of a clay vein coinciding with the low velocity material imaged in the tomogram.

Jan 1, 1992

The following list is a representative sample of the types of software available to the mining industry. For additional information concerning software packages for your minicomputer, contact equipment manufacturers or software suppliers.

Jan 11, 1981

By Dave Willis

Two hundred and thirty million tons of coal! That is what the Burlington Northern (BN) railroad anticipates that it and the Chicago North Western railroad (CNW) will haul out of the southern Powder River Basin l (see map on page 966) in 1994. Put that 209 Mt (230 million st) into railroad perspective. Current average train size is 113 cars. With each car transporting 94 t (103.5 st) of coal, each train averages 10.6 kt (11,700 st) of coal. Simple division shows that 209 Mt (230 million st) of coal equals 19,658 trains a year. So BN and the CNW must move 54 loads a day out of the Basin. Every load, of course, has an empty side of its cycle. This means that 54 loads a day translates into 108 total trains a day, or 39,420 trains a year through the southern PRB.

Jan 1, 1994

By Henry A. Russell

During the last ten years Parsons Brinckerhoff has become a leader in the area of tunnel rehabilitation. A significant part of any tunnel rehabilitation program is the control of groundwater infiltration into the structure. This leakage over time, causes deterioration of the structures, and creates numerous operational problems for the tunnel operator. This paper will address current procedures for identification, documentation, and recommendations of repair methods for the control of groundwater infiltration in rail and highway tunnels.

Jan 1, 1993

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: • The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. • That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. • Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equip¬ment, blasting, or water infusion. • To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. • As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. • When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in. - diam). The techniques in detail are somewhat complex and sub¬ject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1989