Search Documents

By J. W. Wilson, P. C. Graham

SUMMARY The Witwatersrand quartzites in which South African gold mining operations are moat exclusively conducted, are notoriously difficult and costly to drill. Despite this situation, however, with the high cost of developing new mines and extending existing mines, together with the rising cost of labour and mining problems resulting from the ever-increasing depths of workings, the demand for raise-boring in these formations is increasing rapidly. Not only is the demand for raises and shafts increasing, but also the length and size of these excavations. Raise-boring studies carried out in South African gold mines have indicated that increased penetration rates and possibly reduced costs could be obtained if higher thrusts were available at the reaming head. Until fairly recently there has been no raise-boring machine suitable for underground use that possessed the thrust and torque characteristics necessary to achieve high penetration rates in hard abrasive quartzite formations and the cutters available were not really developed for high loading. In response to these requirements a raise-borer, the Robbins 83R was designed and built in Seattle, U.S.A. for the Anglo American Corporation. This machine is operating in South African gold mines and is currently being used at a depth of 12 000 ft below surface in one of the. Group's mines. The initial raises bored have substantiated that increased penetration is attainable at high thrust and it is now apparent that the machine is sufficiently versatile to drill raises of up to 12 ft in diameter in quartzite formation over a length of 2 000 ft.

Jan 1, 1974

By Jamie Bonner, Ray Hutton, Taro Nonaka

The Nancy Creek Tunnel is a deep tunnel, designed to store and convey wastewater by diverting flows from trunk sewers currently at or near capacity in the northwest of the City of Atlanta. The tunnel, constructed in hard rock, has an overall length of 13,300 m (43,700 ft), and a finished diameter of 4.9 m (16 ft). The project is currently under construction by a joint venture of Obayashi/CJB for the City’s Department of Watershed Management. This paper describes the contractor’s techniques and equipment, as well as discussing challenges which were overcome. The project is scheduled to be complete in October 2005.

Jan 1, 2005

By B. M. Davis

Characterizing exploration prospect potential has aspects that differ from those encountered during ore reserve estimation. One problem is determination of the ore reserve potential prior to acquisition of significant volumes of hard data. The evaluation is subjective and data are usually sparse and of uncertain quality. However, estimations of the ore reserve potential are commonly demanded by management before project funding will be approved. The estimations from several prospects, along with the uncertainties inherent to the estimation, are then used to compare and contrast the potential of several prospects, often with widely varying geologic models.

Jan 1, 1990

By Louis W. Cope

Since its discovery, Cuba has been called the “Pearl of the Antilles.” The country remains that, albeit a little tarnished these days. In Havana, many of the buildings are being refurbished, while some new ones are under construction. Since 1991, the laws have been relaxed so that Cuba is developing a mixed economy of central control with free market. Joint venture agreements have been signed with businesses from many countries. This does not include the United States due to its embargo. But even these regulations have been relaxed some.

Jan 1, 2003

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By Syd S. Peng

Mountaintop removal (MTR) mining started in West Virginia nearly 30 years ago. This surface mining method can extract multiple coal seams as thin as a few inches in whole and minimum rock dilution in very steep mountainous terrain. MTR is highly efficient, even if coal seams are in close proximity and small in a real extent. Consequently, MTR has been widely used in the Central Appalachian coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impact on the surrounding area. During the past two years, however, the debate over MTR mining has grown quickly and has become very intense. This article describes chronologically issues raised by various parties, legal actions, impacts on mining permit applications and research projects developed to address the issues.

Jan 1, 2000

By David Young

This paper presents tunnel design considerations for the SR75/282 Transportation Corridor Project in Coronado, California. The project is managed by the City of Coronado in cooperation with Caltrans and the US Navy and may include a one-mile long twin-tunnel section with two options: a 36.5 foot diameter twin-bored tunnel or a twin cut-and-cover box. The alignment crosses the Coronado Fault, and design provisions were needed at the fault crossing to maintain life safety and prevent rapid inundation of the tunnel in the event of fault rupture. These provisions are discussed along with considerations related to liquefaction and ground shaking. The project is currently in the planning stage with construction to start around 2012.

Jan 1, 2008

By M. Fan, Z. Long

"This paper presents some studies on recovering valuable elements from Chinese coal by-products, including coal combustion fly ash, stone coal ash, and coal flotation tailings. Both commercialized technologies and economic potential recovery methods are described in this study. Magnetically stabilized air-dense medium fluidized bed separation, tribo-electrostatic separation, froth flotation, and hydrometallurgical methods are discussed in recovering various valuable elements in Chinese coal by-products from different coalfields. These valuable elements include iron, carbon, aluminum, rare earth elements, lithium, gallium, germanium, uranium, titanium, scandium, silicon, vanadium and phosphorus, etc. The ultimate goal is to fully utilize all valuable elements in coal by-product. Each component within coal by-product should be efficiently segregated to its highest value. INTRODUCTION Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium, and phosphorus, etc. These coal-associated elements are significantly enriched in coal combustion by-product fly ash because of majority of main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main elements oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China, and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary widely due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides, and unburned carbon."

Jan 1, 2017

By Steve Kral

The Prospectors and Developers Association of Canada (PDAC) was established in 1932 in response to proposed regulations that would have threatened prospectors in Ontario. From there, the association grew to represent the interests of Canada?s mineral exploration and development industry. The PDAC?s mission statement reads: ?The PDAC exists to protect and promote the interests of the Canadian mineral exploration sector and to ensure a robust mining industry in Canada. The PDAC will encourage the highest standards of technical, environment, safety and social practices in Canada and internationally. ?Today, the PDAC?s 6,000 individual members include prospectors, developers, geoscientists, consultants, mining executives and students. In addition, the association?s membership includes 950 corporate members, representing senior, mid-sized and junior mining companies in addition to organizations that provide services and equipment to the mining industry. In 2010, the PDAC adopted its e3 Plus principles, a framework to guide its membership in responsible exploration.

Jan 1, 2011

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By N. Arbiter

Introduction The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter (L/D) ratio. This is in spite of the fact that practice varies substantially: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia, and historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills, on the occurrence of the overload phenomenon, and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape factor is of major importance in this area and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type. Dimensionality in mill design Ball mill shape factors in the period prior to 1927 (Taggart, 1927) averaged 1.1/1 for 29 center discharge mills and 1.0/1 for 30 peripheral discharge mills. With the resumption of new plant construction after the 1930s depression, the Morenci concentrator continued the 1/1 ratio with its 3.1 x 3.1 m (10 x 10 ft) mills. The ratio was increased progressively from then on, reaching 1.6 and 1.8/1 for the largest overflow mills currently. As shown recently (Arbiter, 1989), this is in sharp contrast to autogenous and SAG mill shapes, for which the ratio averages 0.4 in North America. On the other hand, South African practice, starting at the turn of the century with autogenous mills having 4/1 ratios, moved toward 1/1 until recently, when a 2.5/ 1 ratio mill was installed. The reasons given for such divergent practice for mill shape factors are in some respects contradictory and generally inconclusive. The most complete discussion from a practical viewpoint (Dor and Bassarear, 1982) is limited to primary SAG and autogenous mills. Considerations of ball mill dimensionality have had a twofold direction. On the one hand, it has been argued that ball mill efficiencies should increase with increasing diameter and that the specific energy for a particular grind should be reduced accordingly. An inadvertent test of this idea at the Bougainville operation (Burns and Erskine, 1983) resulted in drastic underpowering, which led to failure to reach design capacity until additional mills were installed. This can be taken as strong evidence against any increase in efficiency with diameter. In another direction, it has been argued (Arbiter and Harris, 1982, 1983) that there is a limit to ball mill diameters because of the demonstrable limit to axial flow velocities evident in the overload phenomenon, which as a fact is incontrovertible. But that it places a limit on mill diameters overlooks the evidence given below that appropriate variation in the L/D ratio will permit major increases in diameter, limited only by constructional or economic factors. The present study was directed toward quantifying the overload phenomenon through examination of the influence of mill dimensionality variation and mill operating variables on its occurrence. It is shown that varying the operating conditions, specifically the load fraction and the fraction critical speed, can reduce the risk of overload for existing operations; while appropriate decreases in the L/D ratio can minimize the risk in the design of new circuits. Ball mill overload Ball mill overload is a consequence of the approach to a critical velocity with increasing feed rates or circulating loads. Although the effect has been known for over 50 years, there have been no previous attempts to quantify it. The following description of the ball mill as a flow system is the preliminary to a quantitative analysis: 1) In the absence of a ball load, axial flow of pulp through a mill resembles open channel flow, except for disturbances near the shell due to shell/lifter rotation. 2) For a given ball load (Lf), the void fraction available for pulp hold-up (H) for the ascending portion of the load is approximately 0.4 Lf. In the descending portion, it is greater than this and increases with fraction critical speed (Fc) because of load expansion. 3) Increasing the feed rate increases pulp hold-up and progressively fills the available void space. At a critical flow rate, which depends on system geometry, hydraulic head and pulp rheology, void filling reaches its limit; a pool forms rapidly and fills available space outside the ball load and up to the overflow level. Prior to this, pulp discharges mainly along the ascending rim of the overflow. 4) For a small mill (Lo et al., 1990), it has been shown that with increasing feed rates the critical filling is at or near 50% of the mill volume. Power drops rapidly when this level is reached, as required by the torque formula. 5) The transition to overload is associated with the following phenomena: a) The decrease in power draw. b) Damping of mill sound. c) Reduced comminution of coarser feed sizes, probably due to reduced direct impact in the presence of a pool. d) Increased circulating loads, which further intensify the overload, and increased density of cyclone underflows, which can lead to roping. e) Conditions beyond overload are not known because feed rates are not delibelrately increased beyond this point. f) The existence of the phenomenon limits the capacity of a mill with a fixed set of operating conditions and can prevent the balancing of hard ore feed rate decreases by increases in soft ore rates.

Jan 1, 1992

By Ronald E. Triplett, George K. Burke, Bernard H. Voor

To accommodate larger double-stack rail cars through a tunnel, the existing active tracks were to be lowered. The tunnel is an elliptical, horseshoe-shape with concrete base support, removal of which would jeopardize the tunnel integrity, particularly since the soils beneath part of the tunnel floor included soft, saturated silt overlying rock. Grouted bar anchors combined with a SuperJet soilcrete strut replaced the existing support in situ prior to floor lowering. Close cooperation and detailed timely engineering support provided a quality project. Project design and construction, ground improvement methods, and the performance of the work are described.

Jan 1, 2001

By K. Sasaki, W. Astuti, N. Okibe, T. Hirajima

"The kinetics of leaching of a saprolitic ore from Indonesia by citric acid solution under atmospheric pressure was investigated. An examination of the effects of leaching temperature, citric acid concentration, pulp density and ore particle size on the dissolution rate of nickel found that they all had significant influence on the rate. The highest nickel recovery (95.6 percent) was achieved under the leaching conditions of ore particle size of 212-355 microns, citric acid concentration of 1 M, leaching time of 15 days, pulp density of 20 weight/volume percent, leaching temperature of 40°C and shaker speed of 200 rpm. The shrinking core model was found to be appropriate for describing the leaching kinetics of this ore in citric acid solutions at atmospheric pressure. The experimental data were well interpreted by this model with rate of reaction controlled by diffusion through the solid product layer. Using the Arrhenius expression, the apparent activation energy for nickel dissolution was evaluated as 12.38 kJ/mol. Finally, on the basis of the shrinking core model, a proposed empirical kinetic model for the leaching of nickel from this Indonesian saprolitic ore was expressed as a mathematical model, which was verified as consistent with the observed experimental results.IntroductionIndonesia has some of the world’s largest nickel laterite reserves and was the largest producer of nickel – in the form of nickel lateritic ores – in the world in 2013 (Merchant Research and Consulting Ltd, 2014). However, only high-grade saprolites are processed in Indonesia using pyrometallurgical methods to produce ferronickel and nickel matte. Lower-grade saprolites and limonites are removed, becoming waste or overburden in mining site areas. Hydrometallurgical methods, involving either chemical leaching or bioleaching, are now seen as the most important technologies for treating nickel laterites in the future because of their advantage of not only extracting nickel and iron but also other valuable elements. In addition, hydrometallurgical methods consume less energy and have lower capital and operational costs. Although they are recognized to be more suited to limonites, some researchers have studied their use in the extraction of nickel and other metals from saprolites (Guo et al., 2009; Lu et al., 2013). Hydrometallurgical processes for the extraction of metals, especially nickel, promise to be meaningful alternatives to pyrometallurgical processes to primarily treat low-grade saprolites for which pyrometallurgical processing is not favorable"

Jan 1, 2015

By Osvaldo A. Bascur

Most mining and metallurgical plants have developed predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, oil and lube analysis for critical equipment. Process control strategies have also been installed in several metallurgical sites. These control strategies require instrumentation maintenance from local personnel. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is a must for global plant optimization. Specialized performance control monitoring algorithms are required to justify their existence and contribution to the bottom line. Emerging technologies are combining these techniques into a single total plant system. Tools are required to assist in troubleshooting and adapting these process control instruments and strategies. The key is the plant equipment and process control availability and utilization rather than just maintenance.

Jan 1, 1997

By Thomas Gregor, Brian Garrod

As the popularity of precast concrete segmental linings for tunnels is growing in North America, some problems related to grouting of, and near, these linings are starting to appear. The installation of a segmental lining behind a TBM requires that the annular space around the lining be quickly filled with grout to prevent collapse of the ground. In practice, the filling of the annulus is frequently delayed and takes place a distance behind the machine typically via grout ports centrally located in the segments. If partial collapse of the annulus has occurred, it may become necessary to use higher grouting pressures in an attempt to distribute the grout. There have been several occasions where these increased pressures have caused damage to the tunnel linings. Similarly, compaction grouting adjacent to a tunnel lining can cause damage. This paper quantifies the effects of such grouting on a typical precast lining.

Jan 1, 2005

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Openpit mining (prestripping) began in 2010 and full production commenced during 2011. The openpit mines feed both a sulfide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp Inc. Peñasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals.As a consequence of lower grade ores expected with advancing mine life, Peñasquito is facing a declining metal production profile. To maximize returns and asset value, plant modifications, including the addition of a carbon prefloat circuit and a pyrite leach circuit to improve recovery, are currently being undertaken. This carbon prefloat circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Peñasquito operation. The addition of the carbon prefloat circuit was also a key driver in allowing the Chile Colorado openpit to be developed.These conditions alongside Goldcorp’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this article and include improvements in geomodeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 7, 2018

By Roe-Hoan Yoon, Kaiwu Huang

Derjaguin and Dukhin (1961) were the first to develop a model for bubble-particle interaction in flotation from first principles by considering the surface forces in wetting (or flotation) films. The model predicted that the energy barriers to bubble-particle attachment arise from the ζ-potentials of fine particles, which corroborates well with an earlier work of Fuerstenau (1957) reported for the flotation of quartz using dodecyl ammonium acetate (DAA) as collector. In the present work, a series of surface force measurements have been conducted by accurately monitoring the changes in bubble curvature during bubble-silica surface interactions. The curvature changes are then used to determine the capillary force, which is the sum of the hydrodynamic and surface forces. By subtracting the former that can also be determined from the curvature changes, one obtains the surface forces (or disjoining pressure). The results obtained as functions of pH and collector concentrations show that control of the ζ-potentials of bubbles relative to those of the silica surfaces is critical for maximizing the negative disjoining pressure, which is conducive to promoting bubble-particle attachment in flotation.

By Rolland R. Mates

This paper describes the use of post- tensioned rock anchors to reduce the risk of future damage to a residential structure as a result of coal mine subsidence. The project described in this paper was performed by the Office of Surface Mining Reclamation and Enforcement (OSMRE) of the U. S. Department of the Interior. The OSMRE was created to administer Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. The responsibilities of OSMRE include "reclamation and restoration of land and water resources, adversely affected by past coal mining including prevention, abatement, control of coal mine subsidence. ?('l) Consequently, OSMRE has been addressing mine subsidence problems since its initial subsidence stabilization project in 1979. Stabilization activities have primarily consisted of supporting the overburden material by injecting materials through drilled bore holes into the underground mine voids. Injection of various materials into mine voids, including fly ash mixtures, coal refuse, cement grout, and gravel has proven to be a successful method of reducing mine subsidence-related surface movements, and has been extensively utilized in mitigating mine subsidence problems. However, the cost of drilling for injection can be extremely high in areas where the depth to the coal seam is great.

Jan 1, 1986

This paper investigates the effects of solids concentration and the addition of Dispersant S40 on the flowability of original and ground limestone slurries. A rotational viscometer with a concentric cylinder geometry and a controlled-stress rheometer with a cone-and-plate geometry were used to characterize the rheological behaviors of limestone slurries. The rheological behavior of original limestone slurries (<100 µm) is transformed through different types of flows with increasing solids concentration. The use of Dispersant S40 can improve the slurry flowability by decreasing viscosity and eliminating Casson yield stress. It is therefore used as a grinding aid for the wet ultrafine grinding of limestone. The rheological behaviors of ground limestone slurries vary with grinding from a starting dilatant flow-ability to a resulting pseudoplastic one with an evident Casson yield stress in combination with a thixotropic character. The appearance of pseudoplastic flowability combining thixotropy is related to the fineness of a ground product and its specific surface area, which are both correlated to solids concentration and the additive amount of Dispersant S40. In addition, the accurate rheological characterization of time-dependent fluids is dependent on the instruments used and operation conditions.

Jan 1, 2007

By Ingemar Marklund

INTRODUCTION Today at LKAB, the primary mining method used is sublevel caving, independent of ore-body size, shape, dip, and geographical location. The mining of small ore bodies with relatively flat dip involves a lot of develop¬ment work, a large initial investment, big dilution, and large ore losses. In 1975 serious investigations into other possible methods, especially for those small ore bodies which do not lie in direct contact with other ore bodies, began. Different methods were studied and a number of in¬teresting ideas came from Russian mines. An analysis was made of one of the proposed methods, sublevel benching, in which mining is carried out from raises, and which uses the throw from the blast to place the broken ore. However, there were reservations about working in big open rooms at great depth, and doubts about the possibility of getting acceptable drilling results in an acceptable environment from raised platforms. Testing was therefore delayed for a time. However the investigations continued and in the fall of 1976, it was decided to try vein mining in a small ore body (Indian) (see Figs. 1 and 2). MINING RESULTS The results are now available from the mining of Indian and are as follows: Ore plan area 1200 m2 Level height 50 m Ore volume 60 000 m3 Ore tonnage 270 000 t Iron content 62% Dip 0.69 rad (40°) Ore thickness 14 m Ore compressive strength 26 MPa Ore C-factor (fracture density) 0.21 Hanging wall compressive strength 28 MPa Hanging wall C-factor 0.27 About 40 000 m of the holes were drilled by ring drills with an average productivity of 85 m/shift; loading of a round (2 rows, 750 m of hole) was usually accomplished in one shift. The total ore recovery was about 270 000 t with an average iron content of 59%, and three to four shifts were required per round (4700 t) to load. The principal of "throwing" the rock during blast¬ing worked well, and no ore remains on the footwall. ROCK CONTROL Before mining commenced at Indian, it was dis¬covered that the rock strength in its vicinity was rela¬tively poor. Since the ore is flatly dipping, and mining was to take place with open rooms, the strength of the hanging wall was of great importance. A supplementary program of exploration drilling was done during the fall of 1976 in order to assess fracture spacing and rock strength from the drill cores. Results showed that the strength of the hanging wall was low because of the many fractures. A decision was made to try cable bolting of the hanging wall by extending some of the ordinary blast¬holes. Cables (20 mm diam) were grouted in these larger holes and the rest of the hole was then utilized for ordinary loading (see Fig. 2). About 100 bolts altogether were installed and, to date, only small falls have occurred and the hanging wall is holding. Its exposed area is 2100 m2 DEVELOPMENT WORK On the 350-m level, four crosscuts (two per mining room), one longitudinal drift, and two elongated drifts (one per raise) for the raise climber were developed as shown in Fig. 1. Of the 230 m of drift, 60 m were in ore and the rest in waste. For mining room A alone, a total of 115 m of drift were needed with 30 m in ore. The drift dimensions were about 4.5 X 5.5 m. In the drifting on the 300-m level, two connecting drifts were driven from one existing transport drift forward to the respective raises. The total development was 93 m, all in waste (Fig. 1). The two raises having a length of 80 m each were driven at an angle of 0.68 rad (39°) from the hori¬zontal. They were driven along the footwall contact with a separation of 30 m and had an area of 10 m2. LONG-HOLE DRILLING The drilling of long holes with the ring drilling unit began in the fall of 1977 in raise A. The equipment consisted of an Alimak raise climber, equipped with a lower platform from which the charging was done.

Jan 1, 1982