Search Documents

By Michael Amick, G. Swan, R. Hill, C. Pritchard

Falconbridge, a major base metal producer in the Sudbury Basin of Ontario, identified a need to find a safe and cost effective replacement for welded-wire mesh used to support loose ground during underground nickel mining. Falconbridge took a methodical approach to the concept of a spray-on liner as a screen replacement proving the strength characteristics of the liner as a safe, cost effective, and suitable method of supporting ground. Compact, hydraulic mixing and spraying equipment have been developed and are in use at the Fraser mine. The Tekflex material has been approved as a wire-mesh replacement and has been in use since November1998.

Jan 1, 2000

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R and TGA testing setups in our ventilation laboratory, samples from US coal mines have been collected and tested. 70 The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal which is a good indicator for potential of self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential of coal self-ignition. The trend of activation energies determined using TGA techniques and adiabatic tests are reasonably consistent with each other. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal are easier to be activated with a small amount of activation energy at a relatively low temperature, the coal will has a higher potential of self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with low potential of self-ignition has low self-heating rate, high activation energy and high minimum self-heating temperature.

Jan 1, 2012

By S. Suwansawat, D. J. Maconochie, C. C. Chang

This paper describes the overall delivery of the tunneling for the Mass Rapid Transit Authority of Thailand’s Chaloem Ratchamongkhon Line in Bangkok and the constraints provided by the alignment. Eight earth pressure balance tunnel boring machines were employed under two major civil works contracts to drive approximately33 kilometers of tunnel in soft saturated ground beneath the crowded streets of Bangkok. Responsibility within the contract for building damage provided an inherent control for ground movement arising form tunneling when the right of way was narrower than the influence zone. These limits affect the earth pressure balance requirements and permissible ground loss. The methods adopted to limit ground movements and deal with the various obstacles to tunneling influenced the design and operation of the machines. The challenges provided by the need to tunnel through numerous lines of piled foundations of canal bridges and overpasses crossing the alignment are described.

Jan 1, 2001

By Steve Dubnewych

The Joint Water Pollution Control Plant, operated by the Sanitation Districts of Los Angeles County, treats wastewater generated by over three million people. A new tunnel and ocean outfall is being considered to meet future hydraulic demands and provide long-term redundancy for the Districts? existing tunnels, portions of which were constructed as early as the 1930s. The detailed process used to evaluate the feasibility of various tunnel and out-fall locations is described. Challenges include a geologic profile with mixed face and squeezing ground conditions; high water pressures; active fault crossings; gassy and contaminated ground conditions; and liquefaction, slope stability, and lateral spreading concerns in the area of the riser and diffusers.

By Y. Wang, E. Forssberg, A. Johansson, B. Chan

A super-conducting high gradient magnetic separator with matrix vibration in dry separation mode is a powder purification device, which has been used to remove weakly magnetic impure particles from fine calcite powders below 53 µm in this study. A fundamental question concerned is the evolution of the matrix clogging under gas-solids loads. This paper presents the improvement of the separation selectivity using a method of mechanically based vibration on the matrix in the separator. The functions of the matrix vibration are discussed. The results indicated that the mechanically based vibration on the matrix within a high intensity magnetic field while a feed was introduced in an air stream, was found to be effective for the dry purification of fine powder materials.

Jan 1, 2001

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009

North American Coal is a subsidiary of NACCO Industries. Originally founded as Cleveland and Western Coal in 1913, North American Coal took its present name in1925. Today, North American Coal is one of the 10largest coal producers in America, mining about 32Mt/a (35 million stpy). The company mines primarily lignite for electric utilities. Its current operations are in North Dakota, Texas, Louisiana, and Mississippi. In addition, North American Coal’s Florida operation provides dragline mining services for quarries that produce more than 18Mt/a (20 million stpy) of limerock. With more than 1.8 Gt (2 billion st)of bituminous and lignite coal re-serves in the United States, North American Coal constantly seeks new technologies to keep its operations modern, productive and cost competitive.

Jan 1, 2004

By J. Sandford, S. Hennings

EXECUTIVE SUMMARY An approach borrowed from the petroleum industry was applied to the gas development evaluation for the Bulga underground coal mine in New South Wales, Australia. The results enabled the coal mine operator, Xstrata Coal, to systematically plan the extraction of gas in harmony with mine production planning of multiple coal seams. This has allowed for a more proactive approach in preparing the resources and infrastructure needed to capture the gas and accelerate coal mining while maintaining their high level of commitment to safety. Norwest has for decades used gas recovery simulation models to assist the petroleum industry and the coal bed methane (CBM) industry in understanding and forecasting fluid saturations and flow behavior. Norwest developed a similar process with Xstrata to migrate existing mine data at Bulga into reservoir simulation models to study various drainage alternatives. An interesting feature to the evaluation was also developing an understanding of test procedures and nomenclature from the mining industry to properly translate the data for input in simulators developed for the petroleum and CBM industries. The model was then calibrated to actual field data collected from drainage pilot tests that Norwest helped design and monitor at Bulga. The resulting calibrated predictions were then used to develop budgets, schedules, resource requirements, and alternatives for capturing the gas and delivering it to market ahead of mining. Increasing revenue, reducing emissions, improving schedules and cutting costs for the mining operations have all contributed to justifying this advanced approach at Bulga. It has also allowed Xstrata to expand their focus to the sizable gas reserves in seams not currently planned for mining. Several of these seams would be economic gas development targets once the gas recovery infrastructure is installed for the mine. The evaluation process was refined throughout this project and the resulting approach will benefit Xstrata with their broader strategic development of resources in the Hunter Valley and beyond to their worldwide operations.

Jan 1, 2007

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

By R. L. Grayson, J. R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. Thus far environmental groups remain unconvinced, and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This paper presents a fresh and cogent perspective on coal’s role in sustaining society by anchoring the message in a transparent material flow analysis that links coal’s impacts across a broad range of social and environmental aspects.

Jan 1, 2006

By Faruk Oksuz

The owners of large infrastructure projects are challenged on how to implement sound engineering and construction contracting strategies that address their prime expectations: a quality job, on time and within budget. With the increasing number of large engineering and construction projects worldwide, owners continue to search for alternative contracting strategies to address their risk, quality, sustainability (operability and performance), schedule, and budget concerns. Coupled with the shortage of resources, delays, political pressures, and other obstacles in procurement and negotiation processes, engineers and contractors are also looking for creative ways to optimize contract packaging strategies for efficient and successful project delivery. This paper compiles an array of decision making criteria and suggests a balanced evaluation, ranking and selection strategy in procurement of both engineering and construction services for large tunneling and other infrastructure projects. A number of owners? general preferences and viewpoints are discussed on large tunnel programs encompassing water and wastewater conveyance systems, pump stations and treatment facility upgrades. Contract packaging strategies and project phasing and segmenting alternatives for preliminary engineering, final design, construction management, and actual construction of facilities are featured for several large water and wastewater infrastructure projects. While the selection (and the relevant selection process and criteria) and performance of service providers, whether for engineering or construction, have profound effects on the outcome of any given project, this paper only examines strategies for con-tract packaging. More specifically, the authors evaluated case studies and developed a range of recommendations for packaging of large water and wastewater infrastructure projects with multiple components.

Jan 1, 2008

By J. D. Miller, C. L. Lin

In the processing industries, it is well known that particle shape is an important factor which determines the behavior of particulate systems. For example, system properties of technological significance including rheology, suspension stability, agglomeration, packing, permeability…etc, are affected by particle shape. In this regard, characterization and analysis of particle shape is essential for more detailed understanding and improved development of particulate processes. In general, it is clear that the behavior of these systems depends on the statistical characteristics of particle shape. Remarkably few techniques exist to predict the mechanical and hydrodynamic behavior of an irregularly shaped particle or a population of irregularly shaped particles for that matter. The lack of models and correlations can be attributed to the wide variety and complexity of particle shapes, the difficulty of defining shape descriptors suitable for modeling, the limitations of measuring shape, and the lack of classifying techniques to characterize particle shape. In this paper, we present information on how 3D particle shape can be measured, characterized, and analyzed using cone-beam X-ray microtomography (XMT).

Jan 1, 2005

By M. Baumann

Introduction Gold Quarry is one of the largest gold deposits in Nevada, located along the Carlin Trend, approximately seven miles north of Carlin, NV. Owned and operated by Newmont Mining Corporation, as of December 31, 2005, Gold Quarry had produced over 13 million ounces of gold. Multiple simulations were constructed for gold and metallurgical variables using the Stepwise Conditional Transformation method. Analyses of these simulations have been used for a variety of purposes, including an assessment of uncertainty with various ore types. This assessment provides insight for improved modeling and reconciliation. Geological Framework Gold Quarry is a large, low-grade disseminated gold deposit hosted in Silurian-Devonian aged sediments at the Chukar/Alunite-Good Hope fault intersection. Gold bearing hydrothermal fluids appear to have migrated upwards along the Chukar/Alunite and Deep Sulfide Feeder faults and then moved outward along favorable stratigraphic horizons and structural intersections.

Jan 1, 2007

By M. Martins

This work presents and discusses the influence of the surface tension (gLV) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at ?51.0 mN/m. The critical surface tension of wettability (gC) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, and it was 33.9 mN/m when determined by Zisman?s approach.

Jan 1, 2009

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

By R. Bauer

Adaptations and redesign of the existing already very successful and proven road milling machine concept and technical innovations such as an optimized, specifically for mining application developed cutting drum, cutting housing design and cutting tools, high manoeuvrability achieved via a tight turning radius, a three disk clutch system and a cutting drum drive that allows for the acceptance of higher loads, a complete reinforcement of the chassis to withstand higher vibrations and torque, the installation of increased engine power via a modern drive unit, a specifically for mining/construction applications developed operator’s platform and finally a redesigned air intake system and the adaptation of the levelling system resulted in far more cost effective and advantageous capabilities of Wirtgen Surface Miner in soft to medium hard mining and construction applications. As the achieved results show for the first time in modern surface mining history mechanized cutting is capable to compete successfully against traditional drill, blast/ripping and other conventional mining methods.

Jan 1, 2007

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002

By I. Tsolas

This paper presents the use of non-parametric approach (i.e., data envelopment analysis, DEA) for the development of environmental sustainability indicators in mineral processing using environmental, economic and/or integrated indicators (i.e., indicators that interrelate two dimensions of sustainability). A case study based on real publicly available data is presented to illustrate how the proposed approach can be implemented in practice. The merit of this approach, which is based on the productive efficiency framework, is that it provides environmental sustainability indicators that can be used internally for benchmarking purposes and externally for sustainability reporting.

Jan 1, 2008

By William R. Yernberg

The current state of the copper industry was the topic of discussion at the Copper 99 — Cobre 99conference held Oct. 10 to 13, 1999, in Phoenix, AZ. More than 700 copper-industry engineers, executives, consultants, academics, vendors and other interested parties attended. This successful and well-organized conference was the fourth in a series of international conferences devoted to the mineral processing and extractive metallurgy of copper. The 1999 meeting marked the first time that the conference was held in the United States. The meeting was co-organized by the Minerals, Metals and Materials Society (TMS); the Chilean Institute of Mining Engineers (IIMCH) and the Metallurgical Society of the Canadian Institute of Mining, Metallurgy & Petroleum(CIM). The meeting was also sponsored by The Society for Mining, Metallurgy and Exploration Inc.

Jan 1, 2000