Search Documents

By R. J. Latino

Because of the lack of a universally accepted definition or standard for RCA, we are left to our own conventions in the marketplace as to what is most ?effective? or a ?Best Practice? for our own facilities or organization. This lack of uniformity in the application of RCA produces an equal lack of uniformity in the measureable outcomes of RCA on the bottom-line from site to site and industry to industry. What is the definition of success for an RCA? Is it regulatory compliance? Is it some quantifiable measure of bottom-line performance? Is compliance and bottom-line performance the same thing? Can we measure the ROI we receive by doing compliant RCA? These questions must be adequately addressed if any definition of RCA is to be effective on the bottom-line. Like our various Corporate Vision and Mission Statements, what would be our Vision and Mission for RCA? When pondering the answer to this question, we should consider: ? What Key Performance Indicators will the Success of RCA be Linked to? This provides a direct correlation to the corporate dashboard and therefore garners support for the RCA effort when implemented at the sharp end. Not until we know what KPI?s will effectively measure our maintenance and reliability objectives can we begin to establish which opportunities will afford the greatest returns1. ? What Bottom-Line Metrics will be Tracked to Measure the Effectiveness of Our RCA Effort? Will it be increased production, profitability, regulatory compliance, etc.? Will it be decreased injuries/fatalities, claims, customer complaints, risks, etc.? We should be specific about these metrics and their correlation to the metrics on our corporate dashboard. ? What Will Trigger an RCA Investigation? Normally companies will establish quantifiable thresholds to be surpassed before an RCA will be conducted. Examples may be an OSHA recordable injury, a failure event in which production losses exceed $250,000, an equipment failure in excess of $50,000 or a regulatory violation. This is the norm. However, we should realize this is using our RCA skills totally on a reactive basis. High Reliability Organizations (HRO) strive for proaction and they also use RCA proactively. Why can?t we use RCA to analyze why unacceptable risks from an FMEA are so high? It is perfectly applicable yet rarely implemented in this fashion.

Feb 27, 2013

By P. D?Elia

Following a study by NIOSH on the availability of teams in the U.S. as well as existing training sites and their capabilities, the Penn State University, leaders of the Pittsburgh Section of SME, providers of mine rescue equipment, and industry sponsors united to establish and make fully functional a student mine rescue team at Penn State University. With the growth of MERD and mine rescue competitive events at Missouri S&T, the Mine Training and Technology Center in PA, and at Colorado School of Mines Edgar Mine, a critical mass of effective training venues were made available to help student teams progress and develop mine rescue skills. The challenges to be met in creating and developing a student mine rescue team will be discussed. The rewards from this type of effort will be the quick capability of graduates from mining engineering programs to be involved in not only mining operations, but industry mine rescue teams and other leadership roles as well.

Jan 1, 2012

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983

By Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

The depletion of good-quality phosphate resources, coupled by a need to supply acceptable products at a rapid rate, while meeting the specifications of fertilizer chemical plants, is of significant concern to the phosphate industry, particularly the production of concentrates with tolerable dolomite content. Tremendous efforts have been made in the past to develop an efficient and economical process that can effectively reject dolomite. However, dolomite removal continues to plague the phosphate industry due to several process-specific challenges being encountered with various beneficiation technologies. In this regard, detailed characterization of phosphate reserves is crucial to understand textural limitations and help design appropriate strategies to achieve quality products. In this paper, the development of procedures to establish dolomite rejection/francolite recovery curves for gravity preconcentration of pebble phosphate from Central Florida is described using high-speed X-ray computed tomography (HSXCT). The developed procedure is illustrated with the analysis of high MgO pebble phosphate samples (10.39 mm × 1 mm) received from South Pasture and Four Corners locations operated by the Mosaic company. The rejection/recovery curves were calculated for each sample for five different particle size classes to observe the trend in rejection/recovery with variation in particle size. In order to evaluate the reliability of the HSXCT data, analysis using the high-resolution X-ray computed tomography (HRXCT) technique was performed on one particular sample (FC-3-1). Finally, to assess the separation efficiency, the HSXCT and HRXCT rejection/recovery curves obtained were compared to experimental gravity preconcentration results reported in the literature. In this way, liberation limitations for gravity preconcentration in the processing of pebble phosphate have been established based on X-ray computed tomography analysis.

By D. Symonds, A. J. Richins, M. G. Nelson

Mining activities at Kennecott and Park City are similar in that both districts began operation in the last half of the 18th century, and both operated on a large scale for many years. However, they are different for two important reasons. First, the mines in the Park City district were always underground. The city of Park City was above many of those mine workings. It remained in place after mining activity stopped, and as the town became an up-scale ski resort, property values increased and the tailings dumps became desirable building sites. In contrast, Kennecott eventually became an open pit mine, and the growing pit effectively consumed many of the small towns that had grown up around the underground workings. Even towns on the periphery of the open pit were razed to allow for the disposal of mine overburden. Second, almost all mining activity stopped in Park City in the early 1970s, just as the first rigorous environmental legislation in the United States was enacted. (The Ontario mine operated sporadically until 1982.) Many mine structures, waste dumps, tailings ponds and piles, and tunnels were simply abandoned as the mining companies ceased business or were bought out. Kennecott, on the other hand, has been in continuous operation for more than 120 years, so a closure plan hasn’t been finalized. Nonetheless, environmental and social problems have arisen, and the company has had to address them.

Mar 2, 2022

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By Joseph L. Petrillo

In July 1997, Kvaerner Environmental signed a unique contract with Echo Bay Alaska called the Transfer Risk and Accelerate Closure (TRAC). The contract called for Kvaerner to assume the responsibilities and obligations associated with closeout of the Alaska-Juneau (A-J) Mine. Kvaerner is an international engineering and construction company with global interdisciplinary experience in the mining industry and environmental remediation. Echo Bay’s requirements called for Kvaerner to: •Provide a fixed price for closure with no change orders. •Negotiate, prepare and implement a final closeout plan as outlined by Echo Bay. •Complete a closure program that exceeded current regulatory requirements. •Improve, expand and maintain a proactive public and community relations program. •Hire Echo Bay employees where possible. •Provide adequate performance guarantees and judicial relief of environmental claims.

Jan 1, 1999

By Rolf B. Pedersen, Ana Filipa Marques, Ingunn H. Thorseth, Ingeborg Okland

"Deep sea mining of polymetallic sulphides will change the physical and chemical conditions at the seafloor by creating scars when sulphides are removed, and potentially also by deposition of mine tailings at the seafloor. These changes will impact the existing ecosystems at the seafloor in and around the mined areas. Seafloor Massive Sulphide deposits that have been exposed to oxic seawater weather into Fe-metal-oxyhydroxides. However, the rates of weathering and release of heavy metals and other toxic compounds to the environment from freshly exposed sulphides in a deep-sea environment are not well studied.During a cruise to the Arctic Mid-Ocean Ridge in the Norwegian-Greenland Sea in July 2014 we will initiate in-situ experiments investigating the microbiological and geochemical processes involved in the weathering of freshly exposed massive sulphides deposits in a natural environment. This will be done by creating scars in naturally occurring sulphide deposits and by deploying weathering experiments at the seafloor. The sites will be revisited and re-sampled in 2015. The mobility and fate of heavy metals will be one of the main concerns of the study as well as constraining the time it will take for exposed sulphides to return to the chemical state present prior to mining. In this presentation we will present the experimental framework and the preliminary results from the July 2014 cruise. This project is part of the EU funded MIDAS (Managing impacts of deep sea resource exploitation) project."

Sep 1, 2014

By J. J. Gusek

Several final pits in the Seneca No. 1 Surface Coal Mine were abandoned in the 1960's without king reclaimed. In addition, a progressive landslide aggravated by the abandoned mine land conditions was threatening a county mad and private property. An AML-funded project to stabilize the landslide and reclaim the final pits was completed in 1986 for the Colorado Division of Mines and Geology (formerly Colorado Mine Land Reclamation Division). The site was visited after ten growing seasons. The land is stable and the vegetation re-establishment is strong. Volunteer native plant species are now invading the reclaimed sites.

Feb 24, 1997

By Omid Asghari, Amin Mousavi, Arshad Ranjbar

Geometallurgical modeling of the production benches is an attempt to estimate the geometallurgical variables of the different ore domains, which leads to a better understanding of the ore and its properties. Having geometallurgical variables results in a more accurate prediction of ore characteristics, an improved drilling and blasting operation, and better efficiency of the processing plant. In this research, the geometallurgical variables required for the geometallurgical modeling of the extraction benches are discussed. Then, the relations between Bond work index (BWi), as one of the most important geometallurgical variables and the primary grindability index, and rock geomechanical properties are investigated based on the previously published studies. The BWi is the main parameter for measuring the resistance to the grinding of ore minerals. It represents the energy required for processing (e.g., crushing, grinding) ore rocks in the beneficiation plant. As a real case study, BWi of a production bench in Sungun Copper Mine, located in East Azarbaijan province, Iran, was estimated. The rock’s geomechanical properties were measured using laboratory tests, including uniaxial compressive strength, Brazilian tensile strength, point load strength, and hardness. Then, BWi was estimated using the proposed formulas in the literature and the results of the rock’s geomechanical properties. The selected bench consists of three ore zones and two dyke domains. The laboratory tests revealed that the first ore zone has a slightly higher compressive strength than the other two zones, while the compressive strength of the waste rocks is larger than the ore domains. Using the proposed equations in the literature, the predicted values of the BWi for the samples in ore zones are in the range of 6.36 – 14.44 (kWh/t), and therefore this wide range must be considered when the short-term production schedule is planned. In addition, variations are observed in the samples within a specific zone and between the ore zones, demonstrating heterogeneity in the selected bench. Finally, wide-open results obtained by different equations show a necessity to perform a geometallurgical program specifically for the Sungun mine.

Oct 28, 2021

By Aimee A. Woolsey

Enterprise Unmanned Traffic Management is a holistic system concept evolving from technological developments in radio frequency where dynamic tracking can be added into current and emerging platforms. This is done through inexpensive RF sensors capable of real-time and cooperative, non-GPS tracking enabling digital visualization of assets, including unmanned aerial systems (UAS). The RF sensors are low size, weight, and power (SWaP), creating efficiencies in energy and material consumption while transmitting positions in real-time and at long ranges. Multiple UAS and other unmanned vehicles can be visualized for risk mitigation in operations,

Oct 17, 2022

By Morris T. Worley

Editor’s note: Mining companies doing business in Central Asia, and parts of the developing world, should look for ways to promote community development through the introduction of appropriate technology. This article should be of interest to SME members. It shows sustainable development type projects need not be massive or expensive. Smaller, utilitarian projects are equally valuable to developing communities as they seek to develop their own economic and social infrastructures. Joint Development Associates International (JDA) began humanitarian relief and community development in Central Asia in 1992, following the collapse of the former Soviet Union. Appropriate technology has played an important role in the company’s efforts to assist those segments of society that are most vulnerable to poverty and disease.

Jan 1, 2005

By J. MacFadyen

The U.S. cement industry, including Puerto Rico, again set a record in terms of production and shipments. The increase in shipments came primarily from imports of portland cement as domestic production from produced and imported clinker gained only 1.9 Mt (2.1 million st). Clinker production as reported to the U.S. Geological Survey (USGS) was 88.6 Mt (97.6 million st), an increase of 1 percent. Gray and white portland cement production from domestic and imported clinker, estimated at 93.5 Mt (103 million st), was up 1.9 Mt (2.1 million st). Masonry cement shipments of 5.5 Mt (6 million st), which equates closely to production, was up 6.3 percent. Blended ce-ment shipments were up 35.9 percent from 2004 at 2.35 Mt (2.6 million st).

Jan 1, 2006

By J. Restrepo, N. Ripepi

"The International Organization of Standards defines risk as “the effect of uncertainties on achieving objectives (15).” In mining, many uncertainties can influence the outcome of personal or professional objectives and are often difficult to predict. Risk management, the minimization and control of adverse effects from exposure to identified risks, is a well-established concept that can summarized as “being smart about taking chances” (12). Risk management now consists of management processes unique to numerous organizations across many industries, as varying sectors encounter a variety of needs, including the analysis and mitigation of risks related to physical security, product liability, information security, various forms of insurance, regulatory compliance, and workplace safety (12). The reoccurrence of multiple fatality events in the US mining industry, especially the underground coal sector, suggests an opportunity for improved methods of major safety hazard identification, assessment, and mitigation. A risk management approach would include ready identification and mitigation of these risks, inclusive stakeholder engagement, and rapid integration. While many solutions to reducing the risk of mine disasters have been proposed including stricter regulation and improved technology, a comprehensive risk management approach has yet to be fully integrated in the US mining industry. In December of 2006, R. Larry Grayson of the National Mining Association’s Mine Safety Technology and Training Commission called for “a new paradigm for ensuring safety in underground coal mines, one that focuses on systematic and comprehensive risk management as the foundation from which all life-safety efforts emanate (7).” A risk management approach has already been implemented with success in Australia’s minerals industry as part of a transition during the mid-1990s from a prescriptive based health and safety attitude to a more proactive, duty-of care [risk-based] philosophy (13, 16, 17).FUNDAMENTAL ELEMENTS OF RISK MANAGEMENT TECHNIQUES The fundamental components of a comprehensive risk assessment/management program are well-established within the realm of mining health and safety. Figure 1 depicts the elements of a typical mining hazard management framework. The first step in any safety-based risk management system is to identify and assess hazards by their location, nature, and magnitude within a mine. Next, a decision is made about choosing to eliminate, mitigate, or tolerate each hazard. Ideally, a hazard will be eliminated during the design stages of mining, though dynamic mining conditions often require continuous improvement and reevaluation of existing hazard controls. If elimination is not possible, hazard mitigation actions can consist of methods, rules, equipment, competencies, or other mechanisms. If a hazard is simply tolerated, as many inherent mining hazards must be, then specialized administrative controls must be utilized to minimize losses. During this process, the performance of each action is monitored and modified as needed (13)."

Jan 1, 2015

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation has been investigated as a process to convert gaseous CO2 into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results have been achieved using heat pretreated serpentine feed material and high partial pressure of CO2 (PCO2). Specific conditions include: 155°C; P002=185 atm; 15% solids. Under these conditions, 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy has been utilized to investigate the appropriate feed characteristics, identify the process products, and interpret the mineral dissolution and carbonate precipitation reaction paths.

Jan 1, 2001

By W. A. Wright

The use and abuse of social media restate common employee relations issues. Business solutions to these issues require advanced preparation. Employers should establish and enforce social media policies to guide their reactions to employees? social media posts that reflect on the employer and its business.

Jan 1, 2011

By M. H. Morcali

Pistachio nut shells, an agricultural waste biomass, and Lewatit TP 214, a commercial sorbent, were investigated as adsorbents for the adsorption of platinum from dilute hexachloroplatinic acid solutions. Before the pistachio nut shells were carbonized, adsorption percentage was 65%, whereas Lewatit TP 214 ensured almost 100% adsorption. However, after the pistachio nut shell was carbonized at 1,000° C under an argon atmosphere, the platinum adsorption (%) increased two-fold. The effects of such parameters as sorbent dosage, contact time, temperature and solution pH on adsorption were studied in detail in batch mode. The adsorption equilibrium data were best fitted with the Langmuir isotherm model. The maximum adsorption capacities, Qmax, at 25° C were found to be 38.31 and 33.22 mg/g for the carbonized pistachio nut shell and Lewatit TP 214, respectively. The adsorption of platinum on both sorbents was found to be described by the pseudo-second-order kinetic model. The results indicated that the activated carbon prepared from pistachio nut shells can be effectively used for the removal of platinum from acidic solutions.

By Michael Kukay, Paul Conrad, Cosmas Opoku-Ware

This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 ft below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana.

By Hai Lin, Renshu Yang, Yongliang Li, Shizheng Fang

With the aim of solving the large deformation problem of surrounding rock in coal mine roadways with a thin sand-mudstone interbed roof, transportation roadway 1603 in Haoyuan Mine was considered. The failure mechanism of surrounding rock was studied through comprehensive on-site investigations, borehole image analysis, mineral composition analysis, and other means. Numerical simulations were performed to determine the influence of roof layer thickness, lateral pressure coefficient, and coal rib strength on the stability of the interbedded roof. The main reasons for support failure and deformation of the roadway are softening and swelling of the sand-mudstone interbed roof upon exposure to water, insufficient support capacity of the roof due to the soft coal rib, an unreasonable support scheme, or poor construction quality, which can reduce the bearing capacity of surrounding rock. Based on our analysis, a control strategy was devised for a thin coal-mudstone interbed roof. The support scheme combines long and short cable support, strengthening of the coal rib to consolidate the roof, and partially shotcrete grout, and was found to improve the overall mechanical strength of surrounding rock and maintain the stability of the thin sand-mudstone interbed roof. The results of the numerical simulations and monitoring data indicated that the proposed support scheme effectively controls the deformation of the surrounding rock of thin sand-mudstone interbed roof of coal mine roadways while maintaining the safety and stability of the surrounding rock and supporting structure.

Dec 12, 2022

By Roderick Eggert, Dipesh Dipu

We look at the empirical evidence of coal block auctions in India to understand how competitive intensity affects the bid amounts in common value auctions. The results suggest that competitive intensity measured through the number of bidders for a coal block is instrumental in determining the bidding outcomes. The presence of higher numbers of bidders in the auction leads to higher bids - every additional bidder causes the bid amount to rise by INR 142.67 per tonne of coal for auctions studied for 127 coal blocks from 2014 to 2023. The paper also examines the moderating and mediating effect of competition on bids and on excess of bids from the comparative market price of coal from alternative source of Coal India Limited. The results indicate that competitive intensity does not have statistically significant impact on the relationship between common value of coal blocks and bids, neither as a moderator nor as a mediator. The strategic behavior of the bidders has also been observed as bidders have been seen to bid in a higher than market price in order to outbid the competitors.

Feb 1, 2025